Search Documents

By B. W. Clyburn

"Coals from the Corporation's Lingan and No. 26 mines are classified as high-volatile A bituminous, with a very low inherent ash and containing all essential properties to provide metallurgical coal, with the exception of a high sulphur content. Only through proper cleaning at low specific gravity can the pyritic sulphur fraction of the coal be liberated to an extent where final sulphur meets coking standards. This first section of the paper deals with the operation of a Dutch State Mines heavy-media cyclone circuit to achieve an actual separation in the region of 1.30 specific gravity. A discussion of the parameter of control which must be applied along with an appraisal of the results obtained is included in the paper.Introduction Very high fluidity and unusually low ash are the outstanding characteristics of coal from Devco's mines in the Harbour seam of the Sydney coal field. However, sulphur content, mainly pyritic, ranges from 1 to 2.50Jo. To obtain the low and consistent sulphur level required in metallurgical coking coals, preparation at low specific gravity is required. Metallurgical coke is used as the fuel in an iron blast furnace. Its sulphur content largely determines the quantity of slag required to remove it and therefore influences furnace productivity and unit costs. Typical data on the various coal properties of importance in the production of coke are included in Table 1."

Jan 1, 1985

By Alan Bauer

New developments in drilling, blasting and explosives in both open-pit and underground mining operations are discussed, as well as novel surface blasting techniques such as are used in tar sand mining.

Jan 1, 1978

By W. G. Miller, J. D. Scott, D. C. Sego

ABSTRACT The influence of using different extraction processes (caustic versus non-caustic) on thethixotropic strength of oil sands fine tailings is examined, as is the influence of adding a coagulant tocaustic fine tailings. The thixotropic strength of fine tailings at large void ratios manifests itself as a bonding or gel strength that has been widely noted both in the laboratory and in the field. This gel strength has a significant influence on preventing the initial consolidation or settlement of fine tailings. Differences between the fine tailings’ thixotropic strength development are explained based on their physical and chemical characteristics.

Jan 1, 2010

By D. Stone

"The Beal Mountain mine near Anaconda, Montana, is an interesting case history of a mine that has continued operations despite several large pit wall failures over a period of approximately 10 years. The largest event involved some 3.9 million tons of rock that has moved steadily at a rate of about 0.05 ft/day since 1992. This paper documents the geotechnical instrumentation and monitoring programs implemented at Beal to provide the company with a comfortable baseline that supported ongoing operations. The success and failure of a variety of stabilization measures will be discussed, along with typical instrumentation responses for several significant events. The success of Beal Mountain serves as a good model for mines faced with serious geotechnical challenges."

Jan 1, 2002

By R. J. Traill

Introduction Following the discovery of high-grade deposits of pitchblende in the Great Bear Lake area of the Northwest Territories by Mr. Gilbert LaBine in May, 1930, samples were submitted to the Mines Branch for examination and investigation as to suitable methods of treatment (1). The purpose of this paper is to present, briefly, the results of the investigative work conducted on the ores and an outline of the methods developed for the extraction of the radium content and recovery of the by-products. The paper is presented in two parts. Part I gives a review of the history of radium production and of the principal processes used in other countries. Part II describes the work and gives the results of the Mines Branch investigation. Part 1-Radium Production In Other Countries Historical Outline Uranium was discovered in 1789, and more than a century later Madame Curie, while studying the physical properties of this element, observed that the ore of uranium exhibited greater activity than the pure uranium com-pounds she had prepared and traced the cause to the presence of a new element which she named radium. Eventually, research proved radium to be a disintegration product of uranium, and always present in uranium ores.

Jan 1, 1933

By J. E. Gill

THE 1938 season was marked by a distinct lull in exploratory activity in the Province of Quebec. Quebec was not unique in this respect, but the condition appears to have been more acute here than in most other parts of the Dominion. Various causes may be suggested to account for this. The general disturbance in political and economic conditions throughout the world has certainly had an adverse influence. Uncertainty induced by changes in the mining laws of Quebec in 1937 contributed. A third cause was the belief, now held by many, that the easily accessible deposits in the main producing belt extending eastward from. the Rouyn district have now all been found and that new discoveries in this field will henceforth come more slowly and more expensively. A fourth is the lack of conspicuous success by companies and individuals who have interested themselves in less accessible areas to the north, notably the Chibougamau district. A fifth, the unattractive appearance, as viewed on published geological maps, of the vast area extending northward to Ungava bay and Hudson strait. A sixth, the attraction of such speculative funds as were available to the Northwest Territories, where spectacular finds were reported in the fall of 1937. Whatever may be the relative importance of these causes, languor in exploration will ultimately be reflected in production returns. This appears, therefore, to be an opportune time to take stock of the general position of the Industry in the Province and to consider ways and means of counter-acting those conditions which are now impeding, or will in the near future impede, its expansion. At the request of the Institute Secretary, Mr. Carlyle, I have prepared a brief summary of accomplishments to date and a discussion of some of the geological aspects of the problem.

Jan 1, 1939

By S. J. Cook

The subject of capital and the Canadian mining industry is so broad as to be impossible of comprehensive treatment in brief form. The purpose of the present paper therefore will be only to outline in a meagre and somewhat sketchy way the nature and extent of the mineral industry in Canada and to point out those features which are likely to be of general public interest. Canada's mineral industry has a long and creditable production record. The? value of the output per capita rose from $2.23 in 1886 to a maximum of $26.40 in 1920 and the value of the products from ten million dollars in the former year to almost two hundred and twenty-eight million dollars in 1920. Compared with other primary industries and on the basis of the value of production, mining held third place in Canada in 1920, the premier position going to agriculture and the value of forestry production placing that industry second in the list. In the mineral industry, between six and seven thousand properties are operated annually giving employment to up- wards of sixty thousand employees to whom about seventy-five million dollars is paid in salaries and wages. During 1923, seventeen mineral products reached a production value of one million dollars or over in Canada and in order of the values assigned these were: coal, gold, nickel, cement, cop-per, silver, clay products, lead, asbestos, natural gas, stone, zinc, lime, cobalt, sand and gravel, gypsum and salt.

Jan 1, 1924

By N Robb

This paper gives an account of the laboratory testing, plant testing and final inclusion of the two-stage sulphuric acid leaching process in the Milliken mill. Operational results for September, 1962, are presented, showing a uranium extraction of 95.5 per cent, with a saving of some 16 lbs. of 100 per cent H~S04 and some 9 lbs. of lime per ton milled. Methods for effecting further improvements in the process are indicated. HISTORY P RIOR to the incorporation of two-stage leaching, the process for the treatment of uranium ores at Milliken consisted of a single-stage sulphuric acid leach, followed by a solution recovery step involving washing in thickeners and two-stage filtration. The thickener overflow solution was subsequently concentrated and purified by ion exchange, and the uranium was recovered, by two-stage precipitation, as ammonium diuranate. Figure I illustrates this flowsheet. For satisfactory extraction of uranium from the. Milliken ore, a high residual acidity, of the order of 40 grams per litre of free acid in the discharge solution, must be

Jan 1, 1963

By Paul W. Kingston

In New Brunswick, during the 1970's, rocks of the Lower Carboniferous Windsor Group in the Moncton Basin of the Fundy Epieugeosyncline have been the target of intense exploration and drilling programs. Sylvinite ore was discovered in three structural basins of the Moncton Basin near Sussex through a drilling program sponsored jointly by the Federal Department of Regional Economic Expansion and the New Brunswick Department of Natural Resources. In 1973, exploration and development rights to the western end of the Moncton Basin were awarded to the Potash Company of America. One high-grade sylvinite unit, varying between 15 and 70feet in true thickness, with a strike length in excess of 5 miles, is located near the stratigraphic top of the assymetric, semi-diapiric, locally overturned anticline. Late in 1975, exploration and development rights to the Marchbank Syncline were awarded to International Minerals and Chemical Corporation (Canada) Limited. To date, a stratigraphic evaporite sequence, forming the semi-diapiric core of the syncline, has been shown to contain one major high-grade sylvinite unit averaging 70 feet in true thickness over a strike length in excess of 2 miles. Both properties appear to have potential considerably in excess of that revealed by the exploratory drilling, and both, because of numerous mineralogical, structural and stratigraphic similarities, are thought to be depositionally contemporaneous. Both potash deposits lie within 50 miles of the Saint John all-weather deepwater port, thus affording easy access to eastern and mid-western U.S. markets. Further opportunities for potash exploration in New Brunswick are considered excellent, as there are large untested areas with favourable geology and known potassium water anomalies and negative gravity anomalies occurring in the Moncton and Cumberland basins, and in the Central Basin of New Brunswick.

Jan 1, 1979

By A. Flemming

"As the next century draws near, new mine properties must be brought into production to replace existing operations that are approaching their economic life. This paper presents some of the critical technical issues being addressed by Manalta Coal Ltd. as they strive to bring the Telkwa Coal Project near Smithers, BC into production during the year 2000. The mine is planned to produce between 1.0 to 1.5 million tonnes per year of medium volatile coal for export to overseas thermal and PCI markets. IntroductionManalta Coal Ltd. (Manalta) is proposing the development and operation of a surface coal mine and associated infrastructure approximately six kilometres southwest of the village of Telkwa, British Columbia (Fig. 1). The infrastructure consists of a coal washing facility, tailings disposal area, clean coal haul road, access road and rail loadout facility. Over a 25-year period, the mine is expected to produce between 25 and 37 million clean tonnes of coal primarily for the export market.To achieve public and governmental approval for the development, the project will be reviewed under British Columbia’s Environmental Assessment Act. Manalta entered the formal Assessment process in February 1, 1997 with the submission of an Application for a Project Approval Certificate for the Telkwa Coal Project."

Jan 1, 1997

By C. O. Brawner, J. Kalejta II

"The classical approach to control rock fall and ravel in open pit mining has been to use catch benches. The width and volume of benches is most dependent on the bench height, size of loading equipment, blast damage to the face and mining regulations. This was compatible with open pit slopes of less than approximately 45 degrees.As our understanding of rock mechanics and blasting control has improved over recent years, much steeper rock slopes can be developed at many open pit mines. However, narrower benches result in less rock fall capacity.The transportation industry has been very successful in using catch fences to protect highways throughout North America and Europe for years. The authors recommend that cable and ring net fences have a potential major application in open pit mining to allow steeper rock slopes with significant economic benefit. This paper outlines the application, design and operation of catch fences in surface mining for specific conditions. Typical case examples are presented."

Jan 1, 2002

By Ahmad Ghahreman, Denver Cowan, Yeonuk Choi

"Testwork was conducted in order to compare the effectiveness of carbon based catalysts while oxidizing a gold-bearing pyrite concentrate under atmospheric conditions. Without the use of a catalyst the oxidation of pyrite was incomplete after 96 hours, resulting in roughly 60% pyrite oxidation. Furthermore the resulting sulphate yield from unassisted pyrite oxidation ranged between 72 and 84%. It is evident that atmospheric oxidation of pyrite is not viable due to slow oxidation kinetics and high sulphuric acid production when using a ferric sulphate media without a catalyst. The effect of two different carbon based catalysts, one Lewatit® AF 5 a new microporous carbonaceous bead, and the second a granular coconut shell based activated carbon, were tested under the same oxidation conditions as the unassisted pyrite tests. After 96 hours, Lewatit® AF 5 assisted oxidation showed approximately 96% pyrite oxidation with a sulphate yield ranging between 26 and 35%, while the activated carbon assisted oxidation reached approximately 100% pyrite oxidation with a sulphate yield between 36 and 37%. Testwork indicated that not only does the addition of a carbon based catalyst greatly improve the oxidation kinetics and lead to almost complete oxidation, the sulphate yield is also drastically reduced, resulting in very high elemental sulphur yields.INTRODUCTION Pyrite is an important sulphide mineral due to its ability to contain invisible gold concentrations up to 132 g/t (Chryssoulis & Cabri, 1990). As a result, ores composed of only a small amount of pyrite still have the ability to contain high gold grades. This refractory gold cannot be accessed via conventional gold leaching processes, such as cyanidation, and additional oxidative pre-treatment is required to liberate the gold, making it more amenable to extraction (Marsden & House, 2006). Current oxidative pre-treatments do exist consisting of both pyrometallurgical and hydrometallurgical processes including high temperature and high pressure leaching within autoclaves, biological atmospheric leaching and roasting. Autoclaves are a proven process reaching desirable recoveries within approximately a 1–2 hour retention time, due to the increased temperatures and pressures, allowing for an increase in dissolved oxygen (Marsden & House, 2006). The typical reaction for pyrite oxidation within autoclaves is presented in Equations 1, 2 and 3."

Jan 1, 2017

By R. Laplante, P. Radziszewski, P. De Ciccio

"Predicting the effect of wear can lead to improved control strategies that can possibly minimize the risk of catastrophic failure due to wear while maximizing useable life. In the field of geological exploration, diamond drill rod wear illustrates just such a case. Wear conditions vary with geological formations and compositions. The objective of this paper is to determine a general relationship, based in theory and practice, that will approximate drill rod wear and therefore predict remaining drill rod life in the context of Canadian, Australian and South American drilling campaigns. Simulation results allow the definition of simple graphical tools that permit the estimation of the potential drill depth remaining on a given drill rod string. IntroductionWear, in many industrial processes, is an undesired phenomenon for which enormous efforts are made to control, if not eliminate. However, wear, in many other cases, is an intrinsic phenomenon of the given process. In such cases, predicting the effect of wear can lead to improved control strategies that can possibly minimize the risk of catastrophic failure due to wear while maximizing useable life. In the field of geological exploration, diamond drill rod wear illustrates just such a case where abrasive conditions vary with geological formations and compositions.A number of studies have been published on drill rod wear especially with regards to the petroleum industry over the last thirty years (Lewis, 1968; Rollins, 1968; Smith, 1978; White 1978; Rowe and Wilson, 1981; Cheng, 1982; Eustes, 1986; Dudman et al., 1989; Besaisow et al., 1990). Of these, most studies covered management techniques (Rollins, 1968; Smith, 1978; White, 1978; Rowe and Wilson, 1981; Besaisow et al., 1990) and some described case histories (Cheng, 1982; Eustes, 1986; Dudman et al., 1989). However, little (Lewis, 1968) was presented that could aid in predicting wear in the particular case of diamond drilling in the metal mining industry.The objective of this paper is to determine a general relationship, based in theory and practice, that will approximate diamond drill rod wear and therefore predict remaining drill rod life in the context of Canadian, Australian and South American diamond drilling campaigns."

Jan 1, 2002

By D. M. Baird

ABSTRACT A revised stratigraphic section of Carboniferous rocks which occupy about 700 square miles in southwestern Newfoundland is presented. Gypsum, which outcrops at thirty-five different localities, is found to belong to four principal zones in the section. The newly mapped structure of the region makes the otherwise random occurrences of gypsum appear as systematic outcroppings of the four zones which follow the regional structure. Details of several occurrences are given and those most advantageous for exploitation are pointed out. INTRODUCTION ROCKS of Carboniferous age occupy an area of about 700 square miles in southwestern Newfoundland. They occur in a belt, from 5 to 15 miles wide, which extends from the head of St. Georges bay southwestward for 65 miles to the mouth of Little Codroy river (see Figure 1). Several hundred feet of Pennsylvanian rocks overlie rocks of Mississippian age, which are at least 12,000 feet thick. The rocks of the Carboniferous section of Newfoundland are very similar to those of Nova Scotia and represent a northeastward continuation of the same palaeophysiographic conditions. Mississippian measures of Windsor equivalence include thick gypsum deposits which outcrop at many places and which extend under large areas as indicated by sink-holes and by structural considerations.

Jan 1, 1951

By Peter Silveston, Earl Shannon

Process-oriented experiments on the use of coal as an adsorbent for certain soluble components of sewage are described. The capacity of Canadian coals for these components was less than 0.1 per cent by weight for the highest concentration at which these components could be expected to be found in domestic sewage. This is much less than values reported in the past. A pronounced selectivity between components was observed. Experiments on bacteria removal in beds of coal, regeneration of spent coal to restore adsorption capacity and COD contributions of coal are reported in the paper. The simple application of coal as an adsorbent does not seem promising.

Jan 1, 1970

By N. Samman, S. N. Lau

"A series of new, grease-based, solvent free open gear lubricants were developed to meet the demanding service requirements of mining equipment. The use of these products has resulted in better performance under conditions of temperature extremes and in terms of longer component lives. They have gained widespread acceptance within the mining communities for such applications as the lubrication of mining shovels, draglines and ball mills.These products are WHMIS non-controlled and are environmentally acceptable. The benefits and advantages of using this type of product to lubricate mining equipment as well as the field evaluation and experience will be discussed."

Jan 1, 2002

By C. G. McLachlan

Abstract This paper deals with the application of the cyanide process to recover gold from a pyrite concentrate produced by means of differential flotation. This concentrate before cyanidation contains from 0.09 oz. to 0.14 oz. gold per ton, of which only about 60 per cent is recoverable. The rest is so fine that it remains interlocked in the pyrite and therefore is not acted on by the cyanide. The concentrate also contains about 15 per cent pyrrhotite and 0.4 per cent chalcopyrite, both of which are cyanicides. The cyanicidal effect of the pyrrhotite is inhibited by preacracing the pulp with lime, and maintaining a high lime alkalinity during cyanidation. The effect of the chalcopyrice is reduced as far as possible by removing those particles which are free by means of a further flotation step immediately prior to cyanidation. This involves the flotation of some very fine material. After nullifying as far as possible these two cyanicides, the concentrate is cyanided directly, i.e., without being roasted. This leaves the pyrite available for subsequent sale as a source of sulphur dioxide and sulphuric acid, and the entire residue of the cyamde plant, amounting to about 500 tons per day, 1s now being disposed of in this way. Prior to deciding on direct cyanidation, a number of laboratory roasting tests were made. These showed chat, 1f proper control were exercised, a better recovery of gold could be effected from the roasted product than by the direct method of treatment. The tests also showed that the capital cost o the plant would be much higher than that needed for the procedure adopted. The possibility of subsequently selling the pyrite for its sulphur content would also have been eliminated. Introduction A previous paper has described in considerable detail the application of the flotation process to improve gold recovery from Noranda's milling ore, and in so doing has covered the production of an auriferous pyrite concentrate. The present paper deals with the recovery of gold by cyanidation from that concentrate. This gold, though intimately associated with the pyrite, can, for metallurgical purposes, be considered as all occuring in the native state.

Jan 1, 1946

By R. M. Kleine

In the fall of 1968, Sheridan Geophysics leased the Renzy Mine property 50 miles northwest of the town of Maniwaki, Quebec. A 500-tpd flotation mill was dismantled at Belleterre, Quebec, trucked into the mine over a winter road and re-erected during extreme winter conditions. Approximately one billion gallons of water were removed from Renzy lake to expose the orebody. A 3,000-hp diesel generating plant and a self-supporting community were set up during the early part of 1969. This was a remark-able achievement considering that most of the work, including the pouring of foundations and the draining of the lake, had to be done during the winter months. Despite this, the project was completed ahead of schedule and one million dollars below budget. The mill is now treating an average of 800 tpd.

Jan 1, 1970

By Eric D. Jamieson

"How well is the Canadian coal industry able to expand in the tough competition with other fuels in Canada and with other suppliers in the international, metallurgical and thermal coal trade? Coal production as a whole decreased between 1950and 1960 and, although there has been a tripling of production since then, underground production continued to decrease until 1975. This trend has been reversed to a certain extent as a result of the modernization of mines in Cape Breton, but in 1978 over 85% of coal production came from surface mining.Against this background, the paper reviews current Canadian mining operations as described in papers presented at the 1979 CIM Annual General Meeting. Conclusions are then drawn regarding some of the longer-term mining applications in relation to the latest coal demand forecast, which indicates a potential Canadian production requirement of 160 million tonnes per year by 2000. IntroductionThe Canadian 'coal industry is experiencing a period of expansion and a new record for production is set with each passing year. This growth pattern over the last IS years has been based on two main markets-the generation of electricity in Canada and the export of coking coal to Japan. Supply to those markets has entailed either the development of mining, coal preparation and transportation systems for the delivery of large volumes of products with predetermined specifications or the establishment of minesite plants designed specifically to suit the characteristics of the coal in the adjacent deposits (Fig. I).Coal is a low-value commodity in relation to its bulk, and the economics of coal use become progressively less attractive with increasing distance from the producing mine. The transportation component in the export trade and in the movement of western coal to Ontario is a major cost factor. In the latter case, it approaches the cost of coal produced at the mine. In addition, the .international competition among coking coal producers chasing diminishing markets in a worldwide steel recession as well as the competition from U.S. coals and other fuel s for Canadian thermal coal have introduced a tight set of parameters to govern mining practices in all parts of the country. Some appreciation of the required changes in mining techniques brought about by declining traditional markets and the rigorous demands of the new bulk markets can be gained by comparing production from surface and underground mines over the past 25 years (Fig . 2)."

Jan 1, 1980

CORPORATE SOCIAL RESPONSIBILITY CSR is about how companies manage the business processes to produce an overall positive impact on society. - Indentured work, sexual slavery, fair trade, organic growing, business ethics, environmental issues, ?Right to know -Right to decide?, AIDS activism, civil society - Balancing stakeholder issues - Government responses Who are the bad guys? Where are the threats?

May 1, 2010