Search Documents

By Whiting AN

Major changes in the world in recent years are changing the criteria for selection of future developments. Oil prices soared during the 1970's while commodity prices including metals and minerals fell. Many new independent nations, have been created and now control the resources in areas which were once part of great colonial Empires.

Jan 1, 1983

By M Berndt

Four siltite-argillite rock samples were characterised (particle size, chemistry, mineralogy) and subjected to laboratory dissolution testing for 36 to 298 weeks. In two samples sulfur (0.99, 1.69 wt per cent) occurred largely as pyrite, and in the other two samples sulfur (0.96, 1.93 wt per cent) occurred predominately as potassium jarosite. The observed rate of sulfate release from the pyritic samples was one to two orders of magnitude greater than that from samples containing potassium jarosite. Drainage pH values from the pyritic samples were one to two units lower and acidities were ten to 70 times higher than associated values from the potassium jarosite samples. Geochemical modelling supported the hypothesis that pH and concentrations of sulfate and potassium in drainage from the potassium jarosite samples were controlled by the limited solubility of potassium jarosite. This dissolution produced an iron-dominated mineral phase, but iron concentrations in the drainage were well below those predicted by ferrihydrite solubility.

Jan 1, 2003

The mining. operations of Bougainville Copper Pty Limited are located at Panguna on the Island of Bougainville which is part of the Territory of Papua and New Guinea. Mineralisation in the Panguna area was first established by C.R.A. Exploration Pty Ltd in 1964. Exploration work since then has established ore reserves estimated to be 760,000,000 tons of.0.47% copper and 0.4 dwt./ton gold. An economic feasibility study completed in July of this year has enabled a decision to be made to proceed with a major mining operation. The ore will be mined by open cut methods and will be treated in a conventional concentrator with a nominal capacity of 90,000 short tons per day. The concentrate will be pumped as a slurry through a 15 mile long pipeline to a port established on the east coast where it will be filtered and dried ready for export. Other supporting facilities for the mine include two towns, a 135 megawatt steam power station, and access roads.

Jan 1, 1970

By Lawson E, Purkiss S. A R, Van Ashwegen p C

It is only in the past decade or so that industrial exploitation of biological resources and techniques has become regarded as a distinct discipline. Commonly referred to as Biotechnology, it embraces biochemistry, microbiology and the engineering sciences and is mainly aimed at the biological conversion of suitable raw materials into desired end products. The catalytic agents are more often than not bacteria although other micro-organisms such as fungi are used. The range of micro-organisms used is wide and the choice depends upon the desired end product, which in turn depends upon the metabolic attributes, genetically engineered or otherwise, of the cells. The metabolic diversity of micro-organisms has been applied to processes such as antibiotic production, food processing, brewing and chemical production, and of course extraction of metals from ores. Metabolic diversity is, to a certain extent, based on nutrition, which, in its simplest form, can be divided into energy source, carbon requirements and nature of the electron donor producing reducing power to the cells. The source of energy may be light, in which case the organisms are phototrophic (eg green plants, algae). The carbon requirements and reducing power may come from organic sources. These organisms are then called heterotrophic (eg man and most bacteria, including the well known Escherichia colt). However, there is a group of bacteria whose energy metabolism depends upon chemical redox reactions, use inorganic carbon (CO2) and obtain their reducing power from reduced chemicals such as metal sulphides. These are known as chemolithotrophs. They play an important role in mineral recycling in nature and are also ideal for extraction of metals from ores. This is because they are extremeophiles being acidophilic (grow at very low pH) and sometimes also thermophilic (grow at very high temperatures). These bacteria operate in such hostile environments that competition, or contamination, by other organisms does not occur. Extraction of metals from ores by chemolithotrophic bacteria is commonly referred to as biohydrometallurgy. Other related areas are bioadsorption of metals from dilute solution,- microbial treatment of metal contaminated wastes and removal of toxic chemicals produced or used during mineral processing. This paper basically reviews the work that Gencor has undertaken in the field of biohydrometallurgy and the advancements it has made in commercialising the technology, but also touches on certain long-term areas of research that are currently under investigation.

Jan 1, 1995

By Ruston R

When coal mining first commenced in Australia, the principle objective was low cost production with development directed toward recovery of 'easy' coal. Future expans- ion of these early mines into major under- ground operations was neither envisaged nor planned. As the demand for coal grew, these mines were expanded to increase output. however, the absence of initial ventilation planning brought about ad hoc systems wh;ch required continual repair and upgrading. These systems proved satisfactory in the short term because the majority of undergrouni coal mining operations were carried out at relatively shallow depths where gas emission rates were low. By comparison, coal is now being won at depths exceeding 500 metres with a corresponding increase in gas flow from the working seams and adjacent strata. The following paper addresses, firstly, the planning and institution of a ventilation system in a mine where previous inefficiencies were many, and secondly, the value of pre- planning a mine ventilation system in the early stages of mine development, and the need to continually review and upgrade the plan to account for unforeseen ^hanges.

Jan 1, 1983

By S E. Wallah, D Hardjito, B V. Ran

The manufacture of Ordinary Portland Cement (OPC) is not only energy-intensive but also releases a significant volume of carbon dioxide (CO2) to the atmosphere. In addition, OPC in concrete often causes premature deterioration that affects the durability of concrete structures. This paper explores an alternative to OPC concrete called geopolymer concrete.The present research utilises low calcium (class F) fly ash as the source material to produce geopolymer concrete. Several factors that affect the mix design process such as mix proportion, curing time, and curing temperature have been studied. In addition, the long-term properties such as drying shrinkage, creep, and exposure to sulfate attack are also being investigated.The test data presented in this paper reveal that geopolymer concrete possesses high compressive strength, undergoes very little drying shrinkage and moderately low creep, and shows excellent resistance to sulfate attack. The result is extremely promising and demonstrates the sustainability of geopolymer concrete as a construction material for a sustainable future.

Jan 1, 2004

The blasting process involves a complex interaction of a delayed sequence of moving sources of seismic energy which produce nonlinear behaviour near the blast holes. A deterministic description of this nonlinear behaviour represents a formidable problem. The modelling of blast vibrations remote from the blast source may use some of the primary features of the blast design such as charge type, charge weight and initiation sequence. Such modelling of blast vibrations usually assumes linear behaviour remote from the blast holes. Site specific charge weight scaling laws may be used to predict the blast vibration levels with relatively poor accuracy. An important ingredient which is missing from charge weight scaling laws is the seismic source wavelet emanating from each blast hole. The present paper considers some approaches which may be used to determine a suitable source wavelet. The wavelets are suitable for use in the region where linearity may be assumed. In that region, it is possible to model the attenuation and scattering of the seismic wave as it propagates from the blast source to the measurement location.

Jan 1, 1990

By R G. Reddy

The complexity in treating environmentally harmful impurities such as As, Sb, Bi from the base metal matte or metal in the smelting stage are responsible for the high cost of the refining process. The impurity capacities (such as arsenic, antimony and bismuth) of slags were calculated a priori using Reddy-Blander (RB) model. The capacity predictions were for a wide range of matte and slag compositions in copper smelting conditions. The calculated impurities capacities and impurity distribution ratios results are in good agreement with the available experimental and industrial slags data. The a priori knowledge of impurities is useful for reduction of energy consumption and enhanced environmental control in the current and future non-ferrous metal processes.

Aug 21, 2024

By P Pieterse

Kumba Iron Ore Ltd is currently commissioning the Sishen Expansion Project (SEP) û a brownfields project on the Sishen Iron Ore Mine located in the Northern Cape Province, South Africa. SEP is designed to produce 13 Mtpa of product from 21.7 Mtpa of ROM feed. The beneficiation section of SEP employs jigs to process narrow size fractions in the 25 x 0.8 mm size range. The -0.8 mm fraction is screened out ahead of the jig plant and rejected as waste without any prior beneficiation. The processing of this fraction was not included in the early stages of SEP development because no suitable beneficiation or dewatering technologies could be identified within the time-frame required to implement SEP. This paper presents the SEP 1B project, ie the metallurgical and process engineering study that was done to evaluate the techno-economic viability of processing the -0.8 mm material of SEP. To support this evaluation, metallurgical bench scale testwork was done on selected samples characterising the material types used in the SEP for gravity concentration beneficiation. Subsequently, pilot testwork on a 300-ton bulk sample demonstrated that an integrated teeter-bed/spiral circuit could be used to successfully beneficiate the -0.8 mm fraction. The study has established the viability of the proposed process and has concluded that approximately 390 000 tpa could be produced and added to the SEP fine ore product without violating the applicable product specifications. The proposed process has been designed to be implemented in modular units in order to facilitate implementation and ensure future expandability. Based on the recommendations of the study, approval has been granted for the detail design feasibility study. Production is scheduled to commence in the first quarter of 2010.

Jan 1, 2008

The success of any industry depends on the planned integration of the policies and resources of the key components of the Australian economic and political structure - government, industry management, education, research, and the human resources of the industry. The Australian Mineral Industry, like Australia itself, has grown and developed at a rate not foreseen by many of our founding fathers and early industry leaders. Hence, now, as we approach the 21st Century, we need to re-think our approach to the significant new problems that are beginning to face both government and the Mineral Industry. Government initiatives, government information and support services, industry re-structuring, and research and development support, need to be carefully re-evaluated, re-diredted,. and strengthened, so that government, the community, and the Mineral Industry produce and receive the optimum education and research strategies and services. The support of academics and researchers, the development of facilities, and the design of new Courses for the future successful and beneficial exploitation of minerals need particular consideration.

Jan 1, 1986

By Schmidt CG

Parameters affecting gold elution using the AARL process are reviewed and critically analyzed in an attempt to optimise metallurgical efficiency and minimise costs in both current and future carbon adsorption operations. Such factors as acid washing, column geometry, elution temperatures and pretreatment reagents are discussed together with eluant water quality and eluate flowrates. Hot acid washing of carbon prior to gold elution has many benefits. Besides improving elution efficiency when eluting with regional water, a hot acid treatment preheats the carbon without causing any gold leakage. Laboratory data indicated that hot acid washing reduces the mass loss of carbon during thermal regeneration. The eluate going to either zinc precipitation or electrowinning is also relatively free of troublesome impurities (organic contaminants and ferrocyanides in particular). Because of the chromatographic character of the AARL elution where an ionic strength gradient is used to inhibit the readsorption of gold, column geometry plays a significant role. While practical considerations and capital costs may restrain the length of the elution column, high length/diameter ratios are advocated in order to promote the plug flow of column eluate. From both a metallurgical and costing viewpoint, the two significant factors affect- ing the AARL gold elution are temperature and cyanide addition. High temperature and high reagent additions within prescribed limits will improve metallurgical efficiencies, but a balance between energy and reagent costs is required in order to minimise overall elution costs. As pretreatment reagents constitute a considerable portion of the total elution costs, both the addition and consumption of sodium cyanide must be carefully considered. Lower cyanide additions may be effective in certain instances, but the more practical use of 0,6 bed volume of a 2-3 per cent NaCN reagent containing 2 per cent NaOH is advocated. This is equivalent to an addition of 20-30 kg NaCN and 20 kg NaOH per ton carbon Treated.

Jan 1, 1986

By Abbott T. M

Alcoa of Australia operates three Alumina refineries in the South West of Western Australia at Kwinana adjacent to the South suburbs of Perth and at Pinjarra and Wagerup in rural settings 100 and 150 kilometres south of Perth respectively (see Figure 1). Alcoa's total alumina production is currently around five million tonnes per annum and this will increase to 5.5 million tonnes by early 1990. Further expansion of production is likely if current world aluminium demand trends continue. Alcoa's refineries utilise bauxite mined in the nearby Darling Range which is low grade by world standards having around 32 % by weight extractable alumina (by comparison Weipa bauxite yields around 55% alumina). This means that for every tonne of alumina produced two tonnes of solid wastes remain and therefore while we in Western Australia can boast of hosting the largest alumina industry in the world with around 18% of total world production we suffer from having the lion's share or 40% of the world's bauxite residues to dispose of. In its Western Australian setting the management of these residues in a manner which is acceptable to the community creates many challenges. These are primarily due to the mass and volume of waste produced, its chemical and physical characteristics and the environmental features of the local area including close proximity of neighbours, competing land uses and the presence of natural resources such as surface water and groundwater. In addition the trend towards more stringent statutory environmental controls and greater political and community awareness of environmental issues means that we must be able to demonstrate improvements that will reduce the considerable adverse impacts of past practices. Of course we must also try to keep the overall cost of residue disposal as low as possible to maintain our competitiveness with refineries which may have much smaller volumes of waste to dispose of and less environmental constraints.

Jan 1, 1989

By J Zhou, D M. Hunter, S M. Iveson, K P. Galvin

The recovery and concentration of ultra-fine iron ore can provide significant economic benefits. Presently, there are limited options available given the low settling rates achieved by conventional gravity separation and the relatively poor performance of reverse flotation. The Reflux Classifier is a new water-based gravity separation technology that consists of a set of parallel inclined channels positioned above a vertical fluidised section. This arrangement promotes a powerful throughput advantage compared to conventional fluidisation and a highly selective hydrodynamic basis for achieving sharp separations. A high shear rate develops within the inclined channels, which generates sufficient hydrodynamic lift to convey the lower-density particles (even if they are relatively coarse) to overflow while retaining the high-density particles (even those that are ultra-fine) for discharge to the underflow. The technology has previously been used around the world on particle sizes in excess of 0.1 mm. The present work, however, is concerned with density-based separations down to much finer particle sizes approaching 0.01 mm.A major advantage of the Reflux Classifier technology is the achievement of simultaneous gravity separation and desliming via a single-stage separation. A series of continuous experiments was conducted using an iron ore feed with head grade of 35 wt per cent FeT and nominal top size of 0.106 mm, with 59 wt per cent being below 0.038 mm in size. At a low throughput of 1.5 t/(m2 h), the Reflux Classifier produced high-grade products at a high recovery. For the entire feed, grades of 66.1 wt per cent FeT with Fe recoveries of 80 per cent were achieved in a single-stage separation. Within the 0.020–0.038 mm size fraction, grades of 68.8 per cent were achieved with iron recoveries of 94.7 per cent. Excellent recoveries of up to 57.0 per cent were achieved for the -0.020 mm size fraction. The ability of the inclined channels to retain the fine dense material further enhances the effectiveness of the Reflux Classifier by creating an autogenous dense medium effect within the vertical section. This helps to elevate large gangue particles up into the overflow.CITATION:Hunter, D M, Zhou, J, Iveson, S M and Galvin, K P, 2015. Gravity separation of ultra-fine iron ore in the reflux classifier, in Proceedings Iron Ore 2015, pp 143–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By G Barla

In Europe, a major interest in the infrastructure and tunnelling fields is in the new crossings of Alps in the form of base tunnels, which are important components of the high-speed (for passengers)/high-capacity (for freight) Trans European railway corridors. These tunnels cross the mountain belt at the elevation of the main cities and basins located all around the Alps and are longer (up to 57 km) and deeper (up to 2500 m) than all tunnels constructed in the centuries before. The excavation of the first Alpine railway and road traffi c tunnels could in general be carried out successfully by conventional excavation methods. With the great lengths of the new base tunnels, mechanised excavation by using tunnel boring machines (TBMs) is imperative as it contributes significantly to savings in construction time and costs. Questions are however posed on the adoption of such a systematic tunnel construction method given the severe ground conditions which are some time anticipated along the tunnel alignment, with possible major geological hazards such as water inflow in heterogeneous fractured or karstifi ed rock masses, stress-induced tensile failure of hard rocks, and plastic shear failure and squeezing of weak rocks, etc. This lecture is to briefly review the current state-of-the-art in the understanding and modelling of two such critical hazards as spalling/bursting and squeezing ground behaviour. With the present interest in the design of mechanised tunnelling with TBMs in such conditions, the complex interaction between the rock mass, the tunnel machine and its system components, and the tunnel support is studied in detail by numerical modelling. The research and development efforts presently underway with the intention to provide the designer with a novel three-dimensional (3D) simulator of mechanised tunnel excavation are presented. Case examples are discussed with reference to the Lyon-Turin Base Tunnel design.

Mar 8, 2011

By Sataev IS, Malinovskaja ND, Otrozdenova LA, Knodov NV, Maximov II, Kuznetzou OK

The technology of flotation recovery of silver from the residue of a zinc plant is described. The peculiarity of this technology is a preliminary pulp conditioning in sodium chloride solution in the presence of aluminum metal under high temperature. In this process the silver is converted to the metallic phase and then floated with the usual sulphydryl collectors. A variant using a combined technology is also described, in which before flotation is performed about 50 per cent of silver is leached. The total silver recovery with the combined technology comes up to 90 - 94 per cent.

Jan 1, 1993

By S Hapugoda, J Manuel, E Donskoi, L Lu

Sinter can constitute up to 80–85 per cent of the total ferrous burden in modern blast furnace ironmaking operations. The mineralogy and microstructure of iron ore sinter play an important role in determining its physical and metallurgical properties. As a result, characterisation of sinter phases is a cost-effective and complementary tool to conventional physical and metallurgical testing of iron ore sinter in evaluating and predicting sinter quality. Over the years, CSIRO has developed a scheme for characterising iron ore sinter that classifies primary sinter phases such as unreacted and partially reacted hematite and magnetite, and secondary phases, including prismatic high-temperature silico-ferrite of calcium and alumina (SFCA), microplaty SFCA (SFCA 1), dense SFCA, secondary hematite and magnetite, glass, larnite (dicalcium silicate; Ca2SiO4) and remnant fluxes. Quantification of these phases has traditionally been carried out by manual point counting under a petrographic microscope; however, new technologies based on automated optical image analysis, quantitative X-ray diffraction and scanning electron microscopy are now available for evaluation. In this study, two sinter samples of varying chemistry were prepared and characterised using both point counting and automated optical image analysis. The implication of the results obtained for the performance of different quantification methods is also assessed.CITATION:Hapugoda, S, Lu, L, Donskoi, E and Manuel, J, 2015. Mineralogical quantification of iron ore sinter, in Proceedings Iron Ore 2015, pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M Iglesias-Martínez

The potential for iron ore in the Central African Archean belts has received much less attention by comparison to their equivalents in other cratonic regions of West Africa, South Africa, Australia and Brazil. Historically, iron ore is known to occur in South Cameroon and North Gabon with significant iron ore deposits (eg Mbalam in Cameroon, Avima in the Republic of Congo, Minkébé, Bélinga and Boka-boka in Gabon), having been the subject of geological exploration programs carried out by government institutions and exploration companies. Although the presence of strong aeromagnetic anomalies, undeniably related to the presence of greenstone belt formations, has been recognised, this study is the first attempt to assess the potential of banded iron formations (BIF) in the Northern part of the Gabonese Republic in the region between Minvoul and Minkébé (>10.000 km2). Deep lateritic weathering, inaccessible equatorial rain forest and high operational costs are some of the reasons why only limited exploration has been undertaken in the area. This work aims to improve the geological knowledge and to highlight the potential for iron ore of the eastern margin of the Ntem Complex units dated between 3.3–2.7 Ga. Field work showed a series of mafic rocks (amphibolite, anorthosite and gabbro), schist and BIF (described as itabirites in neighbouring areas). Samples from Minvoul BIF showed an extensive and deep weathering to powdery hematite revealing the presence, in thin sections, of iron oxides including magnetite, hematite and martite, primary and secondary quartz, garnet, hornblende, anthophyllite, cummingtonite and epidote. Mineral assemblages and coarse grain size suggest a metamorphic grade ranging from medium to upper amphibolite facies. The existence of known economic iron ore deposits in neighbouring regions combined with an extensive weathering enrichment process are promising factors for potential iron ore discovery in this remote area.

Sep 18, 2023

By R Wei, Y Peng

With the depletion of high-quality ores, the efficiency of extracting difficult gold ores through flotation and leaching becomes very important in the mining industry. Iron contaminants, sulfide and carbonaceous coatings on the surface of gold and gold bearing minerals significantly hinder the recovery of gold during gold processing. As the surface of gold minerals is easily contaminated, coatings of iron oxides and iron hydroxides originated from the grinding process and oxidation of iron sulfides will cause a retarding effect on both gold flotation and leaching.To mitigate the processing issues caused by undesirable surface coatings on gold minerals, a new technology in treating surface coatings of iron contaminants has been developed. The pulp potential and pH of the slurry are altered to allow dissolution of surface coatings which are further excluded by the use of complexing reagents. The current work shows that iron contaminants can be removed from the surfaces of gold through Eh-pH adjustment and chelation which result in significantly improved gold flotation response. The addition of complexants aids the formation of iron chelates to prevent the iron species in the solution from forming iron oxide and iron hydroxide in the flotation conditions.CITATION:Wei, R and Peng, Y, 2014. Mitigating the effect of surface coatings on gold processing, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 187–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By E M. Wightman, C L. Evans

A recent survey of mineral processors undertaken as part of the International Mineral Processing Council (IMPC) Education Commission identified mineralogy as one of the key skills required for mineral processors (the other key areas being comminution, flotation, physical separation, sampling and extractive metallurgy). Past experience in a number of operations has shown what can be achieved when the data outputs from mineralogical tools are coupled with people with the right skills who can transform the data into actionable information. This paper reviews what has been done successfully in plant operations over a period of more than four decades and gives examples of a range of applications with both long and short-term objectives. The examples demonstrate the usefulness of mineralogical data – both basic and complex – in optimising mineral processing operations, whether the data are applied in a simple analysis or in more complex modelling. Similarly, the examples show the range of options available for operations to access the mineralogy information they need – through in-house experts and equipment based in centralised technology centres, through on-site equipment and experts or through external laboratories and consultants.The examples from industry highlight the huge potential benefit of including mineralogy as an integral part of operational best practice and raise the question of why more operations do not utilise what should be readily available data. Successful application of mineralogical data requires skilled people to generate relevant data of the required quality, together with skilled people to interpret the data (this may be the same person). And, as in any project, corporate recognition of the value of this approach to best practice is required to ensure continuing support. With fewer university courses providing courses in process mineralogy to undergraduate mineral processing engineers and chemical engineers, there is an increasing lack of knowledge about what mineralogical information is needed, how to get the required data and, equally importantly, how to turn the data into useful information.CITATION:Evans, C L and Wightman, E M, 2018. Understanding minerals in mineral processing – the basics and beyond, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 363–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Many types of micro-organisms inhabit iron ore deposits contributing to biogenic formation and conversion of iron oxides and associated minerals. Bacteria such as Paenibacillus polymyxa are capable of significantly altering the surface chemical behaviour of iron ore minerals such as haematite, alumina, calcite and silica. Differing mineral surface affinities of bacterial cells and metabolic products such as proteins and polysaccharides can be utilised to induce their flotation or flocculation. Mineral-specific bioreagents such as proteins are generated when bacteria are grown in the presence of haematite, alumina, calcite and silica. Alumina-grown bacterial cells and proteins separated from such cells were found to be capable of separating alumina from haematite. Biodegradation of iron ore flotation collectors such as amines and oleates can be effectively utilised to achieve environmental control in iron ore processing mills.

Jan 1, 2009