Search Documents

By I Gray

While in some cases it is vitally important to measure the virgin stress in rock prior to tunnelling there are a number of cases where such stress measurement is really not required. The concept of having to have a number to put in a numerical model representing a continuum is often quite inappropriate. This paper discusses the cases when virgin stress measurement is required and the most appropriate means to measure it. The techniques discussed cover all of the overcoring systems, hydrofracture and borehole breakout measurements. It also covers the use of rock surface stress measurement, which is easy to perform and should be used to check for changing stress conditions. Unfortunately this technique has been ignored in recent times because engineers are addicted to numerical models requiring far field stresses rather than measuring the real values that exist where they matter – at the tunnel wall. A case is presented in which the measurement of surface stress in a tunnel boring machine tunnel enabled the far field stress to be determined in what must be the world’s largest overcore.CITATION:Gray, I, 2014. The measurement of rock stress for tunnelling, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 153–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By R L. Brathwaite

In New Zealand, volcanogenic massive sulfide (VMS) deposits are found in three main geological environments associated with: 1.   ophiolitic basalts of Oligocene age in Northland and East Cape (eg Pupuke, Pakotai, Parakao and Lottin Point); 2.   with chert and pillow lava in greywacke sequences of Permian-Jurassic age (Torlesse and Waipapa terranes; eg Kawau Island, Te Kumi and Maharahara) and their metamorphic equivalents (Haast Schist; eg Moke Creek and Waitahuna); and 3.   with greenschists (metabasalts) and metaserpentinite of Permian-Triassic age (Ponamu Ultramafics) in Westland (eg Bowen and Wilberg ranges). The deposits consist of small lenses of disseminated to massive sulfide minerals, mainly pyrite and chalcopyrite. Small quantities of copper ore were mined from some deposits in the 1800s (eg Kawau Island from 1846), with the last mining at Parakao from 1961 to 1966. Several deposits have been recently examined for their gold potential with assays on sulfide rock samples as high as 75 g/t Au (Lottin Point).

Jan 1, 2005

By Hoskings R

Conceptual studies of the run of mine stockpiling and reclaiming requirements com- menced in 1975. Final selection of equipment was made in 1978 and the equipment was commissioned in June, 1979. Equipment selection was made after extensive investigation and visits to existing facilities throughout the world. The equipment selected is described and com- pared with the alternatives. Foundations were designed to minimise clean up effort and to ensure stability of equipment under design wind loading without storm bays. Program- mable logic control enables the stacking and reclaiming facility to provide a blended feed to the coal preparation plant.

Jan 1, 1980

By R Lethlean

The mining industry in its drive to optimise equipment use and minimise cost simply to remain profitable in an uncertain commodity market needs to develop a greater understanding of equipment capabilities and cost. The factors influencing mobile equipment fleet cost and performance commence at the time of mine planning and continue to exert an influence over the life of the mine. These factors must be understood at the early stages of any operationÆs planning process as they continue to impact both positively and negatively on fleet performance and operating cost throughout the life of the mine. The key factors examined in this paper include: grades; rolling resistance; fragmentation and truck loading.

Jan 1, 1998

Laboratory scale flotation tests were done on mineral hematite and aspecular hematite ore using oleic acid and sodium oleate as collectors. The mineral hematite floated strongly in the neutral pH region, with an increased pH range of flotation at higher oleate additions. Concentrates with sufficient hematite grade to meet the paint pigment specification were produced using oleic acid and sodium oleate as hematite collectors on the specular hematite ore. Hematite recoveries of 70 per cent at 60 per cent Fe grade were obtained using stagewise roughing. The interaction between hematite and oleate was confirmed as chemisorption but the exact mechanism could not be determined, as two independent phenomena can be used to explain the fact that the pH of maximum grade increased with increasing oleate addition.

Jan 1, 1999

Determination of Porosity and its Influence on Specific Surface

Sep 13, 2010

By M Svartsjaern, D Saiang and K Mäkitaavola

The Kiirunavaara mine is a large-scale (28 Mt/a) iron ore mine located in northern Sweden. The mine is owned and operated by Luossavaara-Kiirunavaara Aktiebolag (LKAB) using sublevel caving (SLC). The SLC area underlies an open pit decommissioned in the 1950s, the current main SLC haulage level is situated at an depth of 1100 m. The main orebody dips 60 degrees to the east with a distinct boundary defining the hanging wall to the east and footwall to the west. Since the 1980s damage has been observed both in the footwall rock mass as well as on the footwall crest of the open pit. Recent investigations indicate that the underground footwall damage is primarily controlled by large-scale slope failure mechanisms. Structurally controlled near-vertical planar shear failures in the upper footwall appear to be driven or facilitated by a step-path like curved shear failure situated in a zone starting ca 250 m, and intersecting the SLC about 100 m above the active mining level. To confirm this failure evolution a pilot underground measuring system has been designed and installed to monitor the expected rock mass displacements indicated by numerical models based on the above mechanisms. The systems consists of 50 m time domain reflectometry (TDR) coaxial cables installed in the footwall both across and away from an estimated damage extent boundary to monitor shear movements along natural joint surfaces. The TDR installation is combined with long extensometers to facilitate differentiation between diffuse shear and rock mass normal expansion. Additionally, a low-tech system of tape extensometer lines are installed in drifts and stopes running perpendicular to the ore strike to monitor horizontal displacements in the infrastructure as the footwall ‘slope’ loses confinement during mining advance when the mined out areas are replaced by caved rock from the hanging wall.CITATION:Svartsjaern, M, Saiang, D and Mäkitaavola, K, 2016. Underground footwall monitoring at the sublevel caving mine – Kiirunavaara, Sweden, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 773–780 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By L Mollison, K W. Mills, N R. P Baczynski, M F. Lee, I A. de Bruyn

This is the first of two papers concerned with rock stress inputs to various mine design issues at the large Ok Tedi open pit mine in Papua New Guinea. The companion paper (also published at this conference) is ‘The Application of Rock Stress Inputs to Stability Assessments at Ok Tedi Mine, Papua New Guinea’ (de Bruyn et al, 2014).Stresses are a required input for numerical modelling of mine design issues. However, for some operations, like the very large Ok Tedi open pit mine in remote rugged mountainous terrain, direct and representative measurement of rock stresses can be technically difficult and expensive. In such situations, development of an appropriate and sufficient understanding of rock stresses can be challenging.This was addressed for Ok Tedi by considering the following:The tectonic and regional geologic setting of the mine.Results from three different programs of rock stress measurement over 19 years, including hydraulic fracturing (1991), acoustic emission (2007) and overcoring (2010). Some interesting results of the overcoring work are discussed. It was done in a 4 km long drainage tunnel, which intersected a thick monzodiorite intrusive that has metamorphosed contacts to host contact Ieru Formation siltstones; anomalously low horizontal stresses were measured within the monzodiorite.Compilation of rock stress measurements from other New Guinea mines and prospects, both in Papua New Guinea and Indonesian West Papua.Comparisons between the variable Ok Tedi rock stresses and similar data from other porphyry copper deposits.CITATION:Lee, M F, Baczynski, N R P, Mills, K W, de Bruyn, I A and Mollison, L, 2014. Rock stresses at Ok Tedi, Papua New Guinea, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J Savage, A Crawford, M Doyle, N McNaughton, T G. Blenkinsop

Area selection criteria for gold exploration have historically highlighted the low prospectivity of high-metamorphic grade terranes relative to regions with lower metamorphic grades. The Tropicana gold project, Western Australia, is a rare example of a major greenfields gold discovery in Archean mid-amphibolite to granulite-facies gneissic rocks that have experienced widespread recrystallisation and partial melting.The project, located on the tectonically reworked eastern margin of the Yilgarn Craton, is part of the Tropicana Joint Venture, which is 70 per cent owned by AngloGold Ashanti Australia (manager) and 30 per cent by Independence Group NL. Construction of the mine commenced in the June quarter of 2011 and first gold pour from open pit mining is anticipated in the December quarter of 2013. The approved project will have a ten-year mine life and in the first three years of operation, gold production will be between 470 000 - 490 000 oz/a at a cash cost of A$590 - A$630/oz.Reserves as at 31 December 2011 total 56.4 Mt grading 2.16 g/t for 3.91 Moz of gold. The mineral resource, as of 30 December 2012, has grown to 7.89 Moz of contained gold, including Inferred Resources of 11.9 Mt at 2.83 g/t for 1.08 Moz.Economic gold mineralisation post-dates peak metamorphism and is interpreted as younger in age (ca. 2500 Ma) than other gold deposits in the Yilgarn Craton on the basis of structural and geochronological constraints. Mineralisation is genetically related to an imbricate thrust stack that records a prolonged history of reactivation during the Proterozoic era. Gold mineralisation formed from higher temperature (>350¦C) silica-undersaturated fluids that preferentially migrated though a favourable intensely potassium metasomatised zone. Permeability created during brittle fragmentation was accompanied by replacement of mafic metamorphic minerals, and synchronous partitioning of strain into pervasively biotite-sericite-pyrite-altered stylolites and shear planes that bound more competent lithons.CITATION:Doyle, M, Savage, J, Blenkinsop, T G, Crawford, A and McNaughton, N, 2013. Tropicana - unravelling the complexity of a +6 million ounce gold deposit hosted in granulite facies metamorphic rocks, in Proceedings World Gold 2013 , pp 87-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Goldfields (Tasmania) Limited operates a small, high-grade underground gold mine on the West Coast of Tasmania, 30 kilometres north of Queenstown. The main orebody, Zone 96, was discovered in 1989, with major development work commencing in 1993. The mine was officially opened in July, 1996. Initial production came from a shallow orebody known as the Sill Zone, some 50 - 150 m below surface, which was accessed by a 1 in 8 decline. Zone 96 lies between 350 m and 550 m below the surface and is accessed by a 402 m deep, 3.2 m diameter internal shaft from the collar level located 100 m below surface. The main ore extraction system in Zone 96 is mechanised cut and fill, using high density paste fill. Run of mine ore and waste are hoisted in a single 5.5 tonne overturning skip, then trucked from the underground collar to the gold plant ROM pad or waste dump, respectively. Ground conditions in the mine vary with orientation and proximity to major faults. The gold is contained in a sequence of strongly altered volcanic rocks adjacent to the Henty Fault. Most of the gold is contained in massive quartz, ranging in width from 0.5 m to 7 m, which has been subjected to substantial faulting. Average mineable grade is about 27 grams gold per tonne. Ore reserves in 1996 proved an initial mine life of approximately 4.5 years at 90 000 ounces gold per annum, with significant potential for additional resources from extensions to Zone 96 and adjacent zones. The lease is located in an environmentally sensitive area and a very high standard of environmental management is an essential part of the operation. This paper describes the relevant aspects of mining at Henty including grade control, ground support, backfill placement and environmental management.

Jan 1, 1998

The minerals industry focus over much of the past twenty years has been on cost reduction and production growth supported, but not driven, by technology improvements. Mergers and acquisitions, and the demands of financial markets, have been high priority items whereas research and development and technology based innovation have received less attention and have been cut back in many companies. Technology improvements will be critical if the industry is to make progress on the stated aims of improving energy efficiency, reducing water usage and maximising recovery from deposits. They will also be important for improving capital efficiency and in treating difficult deposits. However the role technology based innovation will play both in the overall industry, and within individual companies, during the next decade is quite uncertain. There are major challenges in progressing technology based innovation in an industry with limited technical resources which is dominated by long life high capital operations. Specific opportunities for energy and productivity improvements exist but face significant technical and structural barriers that need to be overcome if the industry is to significantly improve performance. Current evidence suggests that changes in approach will be needed for these improvements to be realised. Recent studies in the United States and Canada have highlighted the wide range of energy performance across the industry and the scope for marked improvement from both incremental improvements and increased research and development. Comminution, material transportation and underground mine ventilation were identified as high priority areas. Opportunities within these areas are discussed both in respect of specific technologies and in how they may change performance. The role of open innovation as a source of new technology is also discussed. This is an abstract only. No full paper was prepared for this presentation.

Sep 13, 2010

Cretaceous to Cenozoic sedimentary basins in Western Southland include a wide range of non-marine and marine sediments, in a structurally complex setting dominated by major fault systems. A reassessment of their mineral potential confirms large quantities of nonmetallic minerals (limestone, aggregate, marl), and smaller reserves of bituminous coal, lignite, clays, and oil shale. Hydrocarbon potential is largely untested. Metallic minerals are present in trace amounts, apart from platinum group minerals and some detrital gold. In the offshore area, seismic data suggest the hydrocarbon potential is significant. The Orepuki area has the most interest onshore.

Jan 1, 1992

By A Deakin

It has been almost a decade since the release of the International Council of Mining and Metals (ICMM) Health and Safety Critical Control Management: Good Practice Guide (2015a). During this time the ICMM member companies, along with many others across industry, have been busy designing, deploying and enhancing their own critical control management (CCM) programs. So, what have we learnt? This paper discusses the scope, application and learnings from the implementation of CCM within the mining industry. What’s going well? What are the common challenges? What are the opportunities to strengthen the approach? What are the threats to successful implementation? The paper draws on the author’s experience as one of the key contributors to the development of the CCM Good Practice Guide and an adviser to many mining companies, including six of the ICMM members. The paper focuses on the practical (operational) application of CCM and the cycle of identifying, defining, implementing, verifying and improving critical controls at the frontline. The paper also includes a discussion on the safety performance of the ICMM member companies over the past decade and provides a recommendation for how CCM can be incorporated into a more proactive model to measure safety performance. The paper concludes with practical recommendations that mining companies, regardless of their CCM maturity, can consider as they look ahead. They are supplemented by three additional recommendations for consideration at the industry level.

Apr 16, 2024

Roles of Mineral Impurities and Sulfur in the Leaching Behaviour of Pre-Reduced Ilmenite Ores

Sep 13, 2010

The traditional measure of Lost Time Injury Frequency Rate (LTIFR) as a measure of improvement in safety performance is recognised as inadequate and misleading, lulling managers into believing that safety is improving. It is a reactive measure, and steadily declining LTIFRs around the world have failed to be accompanied by a similar reduction in the fatality rate. This paper confronts the industry with the attitudes of some mining managers, such as one that allowed fatalities to occur in the case of a gold mining company at a rate of one death per 150 000 ounces of gold produced while claiming their safety record has improved, as shown by a falling LTIFR, and viewing fatality reductions as a long-term goal instead of an immediate priority. A quantum shift in management attitudes is required to focus on proactive measurements to detect the indicators of an impending disaster, and to predict conditions conducive to fatalities. Corporate CEOs are challenged to attend the funerals of all workers killed in the workplace. CEOs who fail to attend such funerals send a message to employees that the CEOÆs priorities lie elsewhere, and that profits take priority over workersÆ lives. The dichotomy of whether mining companies are run for the benefit of shareholders or whether companies owe social responsibility to the community is examined. The role of individual responsibility for personal safety is examined, together with the psychology of employees in the mining industry. A number of proactive measurable indicators are suggested to stimulate discussion on developing robust measuring tools to predict and therefore prevent fatalities.

Jan 1, 2003

By A G. Grice

WMC Resources Pty Ltd û Copper Uranium Division operates the large underground Olympic Dam Mine at Roxby Downs, South Australia. These operations mine and process the ore to produce refined copper, uranium oxide, gold and silver. In mid-1996, the company committed to the Olympic Dam Expansion Project (OEP) to expand production from 3.0 million tonnes per annum of ore (85 000 tonnes per annum of copper metal) to over 9.0 million tonnes per annum of ore (over 200 000 tonnes per annum of copper metal). Along with the increase in the ore production capacity of the underground mine and the surface ore handling and processing facilities, expansion of the backfill system was required. The target backfill placement rate was 2.0 million cubic metres of backfill per annum which was to be predominantly delivered as cemented aggregate fill (CAF). This paper discusses the engineering activities undertaken to assess and change the method of designing the required strength of fill exposures. In addition, the operational changes that were introduced to achieve the required fill quantities and the mix designs to meet the specified strengths, including the use of alternate binders, are discussed. This work resulted in a large increase in the fill placement rate and a reduction in the overall unit cost of fill.

Jan 1, 2000

By P Phelan

This paper presents the general background and development of raiseboring followed by case histories of circumstances where raiseboring equipment was used in a different manner to normal. Each project has been summarised for this paper as described below: Case 1: Retrieval of a 40 tonne truck from a stope at Peak Gold Mines. Case 2: Slot raising - Conventional, Uphole and Downhole Reaming at Peak Gold Mines. Case 3: Reamer recovery by Downreaming at Tower Colliery. Case 4: The importance of Mucking Raisebore Holes û Thalanga Project. Case 5: Pilot Drilling Dewatering Holes at Beaconsfield Gold Mines. Case 6: Low angle æcut offsÆ in vein at Telfer Gold Mine.

Jan 1, 1998

By I M. Howard

With the bell-less top (BLT) charging system replacing the centuries old double bell charging method, the furnace efficiency has been greatly improved together with considerable reduction in the furnace down time and operational problems. But still there are many draw-backs which need further attention to achieve better efficiency and operational effectiveness. The performance and operational problems of the BLTs have been highlighted and possible solutions to overcome some of the major problems are discussed.

Jan 1, 1999

During a mineral exploration program in an environmentally sensitive area nearMount Painter in South Australia, a helicopter was used to position, construct and service drilling rigs in order to avoid the need to create new access tracks. The drilling program was designed to optimise the advantages of natural landforms in order to minimise the environmental impact of site construction and drilling activities. This minimisation of land disturbance reduced the required amount of rehabilitation measures to the extent where all impacts of the helicopter-supported programme had disappeared within 12 months of completion of work.

Jan 1, 1995

By I Sherrell, R Jain, P Jansson

With the depleting iron reserves and difficult market conditions, precision in separation efficiency is of utmost importance. Classical local control options are predominant in the industry, but their inability to adjust to resolve application problems of interest has furthered the need of developing and implementing continuous control methodologies.This paper highlights the recent development in control of Outotec SLon® vertically pulsating high gradient magnetic separator (VPHGMS) including programmable logic controllers (PLC) coupled with distributed control system (DCS), on-site human–machine interface (HMI) control panel, advanced process control, continuous online sampling using Courier® 8 and additional modernisation packages including level control and cooling monitoring. These modern control options result in improved efficiencies, promote safer operation and at the same time reduce operational manpower needs.CITATION:Jain, R, Sherrell, I and Jansson, P, 2017. Automation for efficient separation with the Outotec SLon® vertically pulsating high gradient magnetic separator, in Proceedings Iron Ore 2017, pp 211–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017