Search Documents

By H. T. Kennedy, J. E. Little

An empirical equation for the prediction of the viscosity of several pure paraffin hydrocarbons and nitrogen is presented. It involves temperature, pressure and six constants of the material, and it applies reliably to both liquids and gases. The equation is similar in form to van der Waal's equation of state. For the paraffin hydrocarbons methane through r-hexane and nitrogen, an average absolute deviation of 1.9 percent was obtained on 1,006 data points described in the literature by 14 authors. When this equation is extended to complex, liquid hydrocarbon mixtures, a correlation was obtained with an average absolute deviation of 9.9 percent. INTRODUCTION Equations describing the flow of gas and liquid through porous media contain the viscosity coefficient of the fluid. If other pertinent variables remain constant, the volume rate of flow is inversely proportional to this coefficient. In dealing with condensate fluids and volatile oils, however, the compositional effects resulting from changing pressure materially affect the viscosity. The effect of compositional changes also may be significant in certain secondary recovery or pressure maintenance processes, notably miscible displacement or gas injection. Early attempts to describe the performance of reservoirs utilized a volumetric material balance method wherein gas and liquid in the reservoir were identified as produced gas and liquid at the surface. This method of analysis proved adequate for reservoirs at moderate temperature and pressure that contained gas with moderately low amounts of condensable materials. The volumetric material balance procedures for "black oil" reservoirs leave much to be desired when applied to condensate and volatile oil reservoirs because phase behavior and compositional changes are relatively more important in these cases. The alternative is a compositional material balance, which in turn, requires a correlation of properties of the reservoir fluid with composition. This paper supplies this correlation in regard to viscosity, for reservoir crude oils. REVIEW OF LITERATURE The literature contains many empirical equations describing the effects of composition, temperature and pressure on the viscosities of pure liquids and binary liquid mixtures. However, the applicability of a majority of these equations is limited to very low pressures and to a small number of systems. Most of them, when applied to complex hydrocarbon systems, are of little value. The lack of utility of the majority of equations results from the fact that they were developed to show the separate effect of temperature, pressure or composition on viscosity, but not to predict the viscosity as a function of all three variables. And with the few exceptions noted below, they were developed to apply to much simpler systems than hydrocarbon mixtures. Eakin1 developed an equation for the viscosity of pure light hydrocarbons applicable in the gas, liquid and dense fluid regions, and in its most general form is written as µ - µo =A(ebP - e-cpk) The pure component viscosity at atmospheric pressure and temperature T, µo, was calculated using the Sutherland equation: µo = BT3/2/T + S The constants in Eakin's equation permitted the term e-CPk to become quite small at high densities (above 0.215 gm/cc), and the general equation would simplify to

Jan 1, 1969

Jan 1, 1968

By B. A. Eaton

The subject of many discussions and technical papers in the last 20 years has been the prediction of the well-bore pressure gradients that are required to induce or extend fractures in subsurface formations. The subject merits this attention because of the frequently recurring problems that arise from an inability to predict fracture pressure gradients. Encountered in several common types of operations in the oil industry are problems associated with the prediction of formation fracture pressure gradients. When wells are being drilled in both new and old fields, lost circulation is often a very troublesome and expensive problem. Complete loss of circulation has been disastrous in some cases. Many times, such disasters could have been avoided if techniques for calculating fracture pressure gradient had been employed in the well plans, and if casing strings had been set, and mud weight plans had been followed accordingly. In areas of abnormally pressured formations, the prediction of fracture gradients during the well-planning stage is extremely important. In fact, it is as important as the prediction of formation pressure gradients, which has received a great deal of attention in recent years. There are several published methods used to determine fracture pressure gradients. However, none of these methods appears to be general enough to be used with much reliability in all areas. In 1957, Hub-bert and Willis published a classical paper that included the development of an equation used to predict the fracture extension pressure gradient in areas of incipient normal fau1ting.l Overburden stress gradient, formation pore pressure gradient and Poisson's ratio of rocks were the independent variables that were shown to control fracture pressure gradient, the dependent variable. In 1967, Matthews and Kelly published another fracture pressure gradient equation that is different from that of Hubbert and Willis in that a variable "matrix stress coefficient" concept was utilized.3 Later the same year, Costley wrote about a similar idea.5 Goldsmith and Wilson used a least-squares curve-fitting technique and field data from the Gulf Coast area to correlate fracture pressure gradient with formation pore pressure gradient and formation depth.' They noted that the fracture pressure gradient increased with increasing depth while the pore pressure gradient remained constant. In each of these cases, the problem for which a solution was sought was to determine the bottom-hole pressure gradient required to initiate or extend a fracture. Results of the previous work show that fracture pressure gradient is a function primarily of overburden stress gradient, pore pressure gradient, and the ratio of horizontal to vertical stress. There is argument for a fourth variable in that in many cases breakdown fracture pressure gradient is greater than the fracture extension pressure gradient. However, if the fracturing fluid is able to penetrate the formation through the pores or existing cracks, there is very little

Jan 1, 1970

By P. O. Metz, E. L. Wiehe, J. S. Foster

BASED on their analyses of growth kinetics, ibbs' and Harris et al.' have recently proposed that the rate of subcritical graphitization of steel is controlled by the rate of diffusion of carbon in ferrite. illert has concluded that this is the rate controlling growth mechanism when the growing graphite particles are relatively large. Harris et al.' also propose that the matrix surrounding a growing graphite particle is plastically deformed to make room for the growing particle. If this plastic deformation does occur, then preferred recrystallization may be observed around the larger particles. If diffusion of carbon in ferrite is rate controlling, then a graphite particle growing in a matrix of, say, tempered martensite or pearlite, should be surrounded by a carbide depleted zone. Thus, the simple metallographic experiments reported here are sufficient to determine whether or not diffusion of carbon in ferrite is the dominant mechanism for the growth of graphite in steel. The present investigation considers graphitization in five alloys. The compositions are given in Table I. Graphitization was carried out at three temperatures: 900°K (627"C), 950°K (677"C), and 990°K ('717°C). Samples were reacted in both the martensitic and the pearlitic initial conditions. In the hypoeutectoid steels, Sets 7 and 8, .and in the hypereutectoid Fe-C binary, Set 6, graphitization was very limited after 1000 hr at temperature. In these samples graphite particles observed were less than 10 p in diam. In the hypereutectoid commercial steels, Sets 1 and 3, large graphite particles (100 p) did not appear until after 250 hr at temperature. The limited number of graphite particles observed and the range of sizes obtained prohibited measurement of growth rates in this investigation. However, in all samples showing graphitization, neithe a carbide depleted zone nor recrystallization was observed. illert's model predicts that diffusion of carbon in ferrite should become dominant for graphite particles larger than about 300 p in diam. The largest graphite particle observed in this investigation was approximately 450 p in diam. No evidence of carbide depletion was noted. Fig. 1 shows a typical graphite particle. This nodule is from an initially pearlitic sample from Set 3 after

Jan 1, 1970

By J. L. Green

Virginia-Carolina Chemical Corp., in its Florida Operations, uses both roller mills and ball mills in dry grinding of phosphate rock. The roller mills have been in operation since 1954 in the Mining Department. The ball mills were installed and put in operation in 1960 in the Harding Concentrate Superphosphate Plant. The roller mills in the Mining Department are used to grind phosphate rock for outside customers. This involves short notice orders of varying grinds, grades and types of rock. The ball mills grind phosphate rock for use in V-C's own phosphoric acid and concentrated superphosphate plant. These mills grind generally two types of rock for one grind. In 1959, a 10% speed-up was made in the operating speed of the roller mills. This paper deals with the operational gains and resulting cost savings which evolved from this speed-up, and compares the present operations of the roller mills and of the ball mills in grinding phosphate rock. In January 1959 it was decided to determine the feasibility of reducing the grinding cost on the roller mills, per ton of rock ground, by speeding up the mill 10%. At this time, one mill was completely reconditioned so it would be in top condition. Extensive tests were then run both before and after the mill speed-up to determine the resultant cost savings. These tests showed that, due to this 10% speed-up, the mill capacity was increased approximately 20% and grinding power costs per ton were reduced approximately 10%. Table I shows the results of these tests. Each test run actually represents several of the same type rock and grind, averaged together. Each test run lasted approximately three hours. The validity of these runs has been confirmed by subsequent operation in grinding over 1,000,000 tons of phosphate rock. Accurate records have been kept on power consumption and repairs as well as tons produced. Two types of feed rock were used for the tests — pebble phosphate rock and flotation phosphate concentrate rock. The pebble phosphate rock size is approximately 80-90% plus 20 mesh. The flotation concentrate phosphate rock size is approximately 15% plus 20 mesh and 95% plus 100 mesh. The same two types of rock feed were used for all the test runs. Test Nos. 1, 2, and 3 were run at the original mill speed of 85.5 rpm on the vertical shaft. Test No. 1 was run with a feed of high grade flotation concentrates; the desired fineness attempted was 70% passing 200 mesh. Tests No. 2 and No. 3 were run with a feed of low grade pebble. Test No. 2 was run for a desired fineness of 70% passing 200 mesh. Test No. 3 was run for desired fineness of 50% passing 200 mesh.

Jan 1, 1963

By T. F. Witherbee

THE Fletcherville Furnace was built in 1864 and 1865, making its first blast from August until October of the latter year, when it was blown out to prevent its "bunging-up." Repairs were made in time to enable it to be blown in again December 12th, 1865, the blast ending October 7th, 1866. Total product 1921.15 tons iron, an average of 6.8.2.5 tons per day, from ores yielding 44.8 per cent. Consumption of charcoal 223.2 bushels per ton of iron. The furnace journal up to this time shows no record of furnace dimen¬sions, or temperature of the blast, but as near as can be ascertained, they were as follows, viz. Height of stack, 42 feet. Diameter of bosh, 11 feet. Angle of bosh, 7 1/2 inches to 12 inches rise, about 58°. Diameter of open tunnel head, 42 inches. Number of tuyeres 3; each 3 inches in diameter. Dam 15 inches high. Tuyeres 24 inches high. Tymp 22 1/2 inches high. Diameter of steam cylinder, 20 1/4 inches. Stroke 5 feet. Diameter of blast cylinder, 64 inches. The engine is direct-acting horizontal non-condensing. December 26th, 1.866, the furnace was again put in blast, having been considerably altered in the crucible; the height of stack, bosh, and tunnel head remaining as before. Six tuyeres were put in, three in each of the side arches. The hearth or crucible was rectangular in form, 3 feet wide x 32 feet long x 62 feet high. Inclination of bosh 58°. Height of tuyeres 26 inches ; nozzles 2 1/4 inches diameter. Temperature of blast estimated to be about 500°.

Jan 1, 1874

By C. E. Van Orstrand

An intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it mill be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. 11. Emmons minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. Mathematical Theory In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be as- sumed that the intrusive is a large par-allelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, 1 = o), which has the same thermal properties as the intrusive, is2,3 l-x v I FT 2 [2 2 — l-x m — y — m — y n — z In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. v = temperature at point x, y, z, time 1. v, = initial temperature throughout the intrusive, 1 = o. k = coefficient of thermal diffusivity. a, ß, y are variables of integration. Put n = m in Eq. I, and we have v I [2/5 [2I-x 2 — l-x m — y 2 2 2 kt 2 20xt e-a2da ebrdß

Jan 1, 1946

By C. E. Van Orstrand

An intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it mill be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. 11. Emmons minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. Mathematical Theory In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be as- sumed that the intrusive is a large par-allelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, 1 = o), which has the same thermal properties as the intrusive, is2,3 l-x v I FT 2 [2 2 — l-x m — y — m — y n — z In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. v = temperature at point x, y, z, time 1. v, = initial temperature throughout the intrusive, 1 = o. k = coefficient of thermal diffusivity. a, ß, y are variables of integration. Put n = m in Eq. I, and we have v I [2/5 [2I-x 2 — l-x m — y 2 2 2 kt 2 20xt e-a2da ebrdß

Jan 1, 1946

By J. Geertsma, F. de Klerk

During the hydraulic fracturing treatment of an oil or gas well the liquid pressure in the borehole is increased until tensile stress in the surrounding rock exceeds tensile strength. Once a tensile fracture is initiated, it is penetrated by liquid from the borehole and fracture propagation under continuous hydraulic action takes place. The fracturing liquid carries a propping agent to ensure a highly permeable flow channel after pressure release. Field results range from failure to obtain increased production to outstanding success. In all cases, however, it unfortunately remains uncertain whether the values chosen for the operational parameters, such as injection rate, pumping time and fluid viscosity, were in fact the ideal ones. Though experience provides a lead, a more satisfactory way to predict results would seem to be to subject the fracture propagation process to a theoretical analysis that (1) makes the maximum use of the relevant physical information and (2) so simplifies the resulting calculations that the field engineer gets practical data that he can handle comfortably. We are attempting here to do this in connection with the prediction of fracture width and areal extent before pressure release. What remains of the fracture afterwards depends on the distribution of the propping agent between the fracture walls, and that is a separate story. Idealization of the Problem To keep the problem tractable, a number of simplify- ing assumptions have had to be made: 1. The formation is homogeneous and isotropic as regards those of its properties that influence the fracture-propagation process. 2. The deformations of the formation during fracture propagation can be derived from linear elastic stress-strain relations. 3. The fracturing fluid behaves like a purely viscous liquid; i.e., any peculiar flow behavior due to the addition of gelling agents or other additives is neglected. Moreover, the effect of the propping agent distribution on the distribution of fluid viscosity in the fracture is not taken into account. 4. Fluid flow in the fracture is everywhere laminar. 5. Simple geometric fracture-extension patterns are assumed — either radially symmetrical propagation from a point source (Fig. 1A) or rectilinear propagation originating from a line source (Fig. 1B). In the first case the periphery of the fracture is circular, in the second case it is rectangular. 6. A rectilinear propagation mode can be accomplished only by injection over a large perforated interval, thus forming a line source. Such a rectilinear fracture must therefore be located in the vertical plane. A circular propagation mode might be expected from injection through a narrow band of perforations. This forms a point source. Because gravity effects are excluded from our considerations, the fracture propagation plane may in this case assume any angle with respect to the wellbore as far as the

Jan 1, 1970

By Walter F. Bradley

CLOSE to 300 members and guests were registered at the Regional Meeting of the Institute in San Francisco. Oct. 3-6, and many other mining men were present at some of the sessions, but failed to register. Headquarters were at the Palace Hotel. Technical papers for the Metals Session were sponsored by the San Francisco Section, whereas the program for the Industrial Minerals Session was arranged by the Southern California Section. Walter W. Bradley, Chairman of the San Francisco Section, opened the General and Metals Session, introducing President Buehler, who gave a hearty welcome to those present. Clyde M. Eye, of the. Benguet Consolidated Mining Co., presented the first paper, entitled "The Economic and Strategic Value of Philippine Metals to the United States." In closing, he urged. that this country retain and control the Philippines because their large

Jan 1, 1935

By Rudolph Emmel

THE mines operated by the South American Development Co. are located in the Zaruma mining district of southwestern Ecuador. They are near the old mining town of Zaruma, which is the only important city in the canton of the same name. The district is situated in the upper end of a valley lying between two spurs of the Cordillera, one of which may be considered the Coast Range and the other an intermediate range. The mining camp proper, known as Portovelo, and the plant are 2.4 km. south of Zaruma, on the north bank of the Amarillo River, a tributary of the Tumbes River, which flows southwestward through Peru to the Pacific. Portovelo is difficult of access; it is reached from Guayaquil by means of river steamers and muleback. Embarking at Guayaquil, the route is down the Guayas River, across the Jambeli Canal, and up the Santa Rosa River to Santa Rosa, a distance of 177 km. From Santa Rosa, the road or trail follows the Santa Rosa River, then across the summit of the Coast Range into Portovelo, a distance of 74 km.-a two-day trip on muleback. The mining property of the South American Development Co. comprises 297 lode claims and 142 placer claims. The combined lode claims cover an area, roughly rectangular in shape, 9000 m. long from north to south by 4000 m. wide; the northern edge of the rectangle is about 3000 m. north of the central plaza of Zaruma. Mineral lands in Ecuador are held by virtue of an annual tax per claim paid to the central government, no surface rights being included.

Jan 1, 1925

By L. B. Slichter

Prospecting is certainly the world's biggest and best gambling business. It is a game where the chips cost many thousands and where many millions, even billions, can be won. An attractive feature of this gamble is the fact that the players are free to rig the odds as favorably as possible. Only the limited bounty of nature, the restrictions of the laws of the land, the competition from other players, the limited sagacity of the player himself— only these, and other factors, restrict the possibilities for large winnings. Today probably about half the land surface of the earth remains to be searched for signs of ore visible at the surface. It is fortunate that so much land still remains for exploration by relatively economical methods. Looking to the future, it is a good guess that the costs of finding ore will increase in response to increasing technical difficulties. To continue to achieve profits from prospecting, it will become necessary to analyze the business more skillfully, in a more and more sophisticated manner. Whenever feasible, qualitative concepts must be replaced by their quantitative equivalents, improvements, and extensions. THE GAMBLE The fact that prospecting is a gambling business reminds us at once of the elementary rule known as the law of gambler's ruin. I hesitate to mention so simple a rule in this company of experts. This rule expresses the rather serious chance of going broke when the odds for success are small, merely by a normal run of bad luck regardless of the long-run expectations of gain. The only sure way of avoiding this special risk of gambler's ruin is to have enough capital, and the will, to continue the play many times and thus ride out the inevitable runs of bad luck. For example, if the probability of success is one in ten for each venture, there is a 35 pct chance that ten successive ventures will fail in a row. But if one has the capital to continue the play through a run of 100 failures, then the chance of gambler's ruin is only 5 in 100,000. Almost any management, I suppose, would be under terrific pressure to cease the play during a long run of bad luck. To continue to prospect under such circumstances requires great confidence in the premises, and a firm conviction in the long-term expectation of profit. There is evidence which I shall mention that in the future even the strongest companies may not have the necessary capital to prospect on the ideal scale. Joint ventures will be very desirable as a means for extending the available venture

Jan 1, 1961

CYRIL STANLEY SMITH, Chairman CARL E. SWARTZ, Past-Chairman ARTHUR PHILLIPS, Vice-Chairman E. E. SCHUMACHER, Vice-Chairman H. A. MALONEY, Treasurer FRANK. T. SISCO, Secretary 9 West 39th Street, New York, N. 1. Executive Committee 1944 1945 WILLIAM C. ELLIS C. S. BARRETT ALAN MORRIS T. A. WRIGHT KENT R. VAN HORN L. L. WYMAN

Jan 1, 1943

By A. G. Rozner

TRANSVERSE rupture tests have been commonly used in mechanical investigations of brittle materials. The specimens are simple, easy to prepare, and loading presents no difficulty. Owing to the complexity of stress distribution in bending1 one can determine stresses rigorously only for the elastic range. The bend-test results, however, are at times converted into tensile-strength data, determined as maximum fiber stress. The assumption is made that for small plastic deformations the linear stress-strain relation applies. This problem was experimentally investigated by Bach3 who tested cast iron in bending and in tension and found that the maximum fiber strength obtained in bending exceeded the experimental tensile strength by a factor depending on the geometry of the tested piece. The factor varied from 1.57 for a rectangular cross section to 2.12 for a circular cross section of the tested beam. Since this work was carried out 60 years ago, the cast iron used could be expected to have been highly brittle, thus the extent of plastic deformation prior to fracture very small. We have therefore carried out a number of tests on magnesium-modified cast iron with an average elongation of -5 pct. It was hoped that the data obtained from the tests would serve as a guideline for comparing data obtained in tension and bending for brittle materials. Mechanical properties were measured at room temperature on an Instron tensile machine at a crosshead speed of 0.05 in. per min. The three-point bend test employed cylindrical bars 0.20 in. in diameter with a 1.0-in. span. For the tensile test, cylindrical tensile specimens with a gage length of 0.85 in. and a diameter of 0.160 in. were used. Results are summarized in Table I. From Table I one can see that fracture strength

Jan 1, 1965

By AMY F. JENNINGS

TO give a concise history of the Woman's Auxiliary of the A. I. M. E. is a difficult task and much interesting information must needs be omitted. The organization has grown and evolved so much from its early simple beginning that it seems best to adopt the technique of some of our modern novelists and begin with the latest development. As the headquarters of the A. I. M. E. is in New York, it follows that the Woman's Auxiliary to the A. I. M. E. necessarily has also its central office and government there. The affairs of the organization are administered by a duly-elected president and five vice- presidents, a treasurer, recording secretary, and corresponding secretary and a board of directors, the personnel of which includes each chairman of a section or an elected or nominated representative who is able to attend the monthly meetings of the board and correspond with the section for which she acts, and the chairmen of the five standing national committees, i. e. Educational Fund, Library, Emergency, Membership and Hospitality. The chairmen of these committees are all responsible to the president and board of directors and their activities must be indorsed with their approval.

Jan 1, 1929

Jan 1, 1897

By L. A. Roe

Magnetic separation of iron ores is one of the fastest-growing segments of the minerals beneficiation industry. The tonnage of taconite ores processed annually by magnetic separation will, in a few years, reach 100 million. Magnetic separation occupies an attractive position in the field of ore beneficiation. It is a simple yet effective method, used for some 150 years and steadily growing more important. This type of beneficiation orginated in 1792, when William Ful-larton was issued a British patent covering the separation of iron ore by magnetic attraction. What is magnetism, and why are some materials capable of being magnetized and others not The study involves many unknowns, and even a partial answer to these questions would be a dissertation in solid state physics and perhaps other fields of science. But the last two decades have revealed basic facts as to why certain materials are magnetic and what happens to them when they are magnetized. Some of the newer studies in solid state physics have developed a theory that can be applied to studies of magnetism. It is claimed that magnetism stems fundamentally from the spin of electrons in atoms that tend to go in pairs, spinning in opposite directions. The atom as a whole can act as a magnet only when there is an imbalance of electronic spin. Whenever an atom has an odd number of electrons, therefore, this imbalance exists. This neutralizing effect explains why a piece of material that contains atomic magnets is not necessarily magnetic. The physicists tell us that iron is composed of many small magnetized regions called domains, which consist individually of millions of atoms. The piece of iron becomes magnetized when an external force lines up these domains in the same direction. Fundamental data developed by physicists working in fields far removed from minerals beneficiation are now available for developing better magnetic separators for ore processing. More Data Needed on Magnetic Properties of Minerals: There is less information on magnetic properties of minerals than there is for certain aspects of magnetic separator design. When the data on magnetic properties is available, it is often directed toward the study of powders for tape recorders and other highly scientific endeavors that are of little use to the beneficiation engineer. W. R. Crane's table of tractive forces, published in 1902, is still a guide in the study of magnetic minerals. Bits of other information regarding electrostatic conductivity, dielectric constant values, and permeability of various minerals have also appeared but are of small practical value in magnetic separation of ore. It is extremely important to obtain pure mineral specimens for making investigations and to record results that may be of use in studies of magnetic processes. Reference to the large volume of data developed by those concerned with analysis and design of permanent magnets soon reveals that these people have extensively evaluated the effect of various impurities on magnetic properties. Much of the science of the ferrite industry is based upon spinel-type structures which are varied by substitution of selected elements or even subtraction of elements, leaving vacant sites in the space lattice. Magnetic separators are used to beneficiate a wide variety of industrial minerals. In this application the relatively large volumes of nonmagnetics are usually the commercial products. The amount of mag-

Jan 1, 1959

Jan 1, 1944

Jan 1, 1944

By H. E. Biber

DURING the production of tin plate a thin layer of FeSn2, is formed at the interface between the steel sheet and the protective tin coating. Because excessive amounts of this alloy layer are undesirable, the kinetics of its formation is a subject of interest in the tin-plate industry. A recent study of this subject at our laboratory uncovered a relationship which should be of general interest to anyone studying kinetics of reactions in metallic systems. It had been previously concluded that, at any given temperature in the range 175" to 330°C, the Fe-Sn alloy layer would have a parabolic growth rate.1,2 However, our studies showed that this rule apparently holds only when the tin plate is heated very slowly to the "reaction" temperature; when the tin plate is rapidly heated, considerably different growth rates occur. An example of this effect of heating rate on growth behavior is contained in the accompanying results of alloy-layer growth measurements at 240°C in oil baths stirred at 10,500, 1800, and 0 rpm. The heating curves for these three conditions are given in Fig. 1, and the growth data are presented in Fig. 2. With the rapid heating rate, provided by the stirring at 10,500 rpm, the alloy layer had three distinct stages of growth. In the initial stage, which persisted well beyond the time required to heat the tin plate to bath temperature, the alloy layer formed very rapidly. The growth followed a rate law of the form w = ktn where n > 1. This initial stage was followed by a growth-retardation stage of about 50-sec duration in which little additional alloy was formed. In the third stage the growth again followed a rate law of the form w = ktn, but here « =0.3. With the intermediate heating rate provided by stirring at 1800 rpm, the three-stage nature was less pronounced and the slope of the third stage increased (i.e., n > 0.3). With the slow heating rate provided by the unstirred oil bath, the alloy layer grew in two stages. The initial rapid-growth stage persisted only until the specimen was heated to bath temperature, no growth retardation was observed, and the slope of the main portion of the plotted data was greater than in the stirred baths, having a value of almost 0.5. Similar results were obtained for other bath temperatures in the range 200" to 300°C. This effect of heating rate on growth behavior may be due to changes in the rate of nucleation of FeSn, crystallites. The iron and tin are in contact from the onset of heating. Thus the initial formation of FeSn, occurs not at the "reaction" temperature but rather while the tin plate is being heated to that temperature. Because nucleation is in general temperature-dependent, different heating rates could cause different over-all nucleation rates, which in turn could cause different growth behaviors. A more detailed discussion of the growth of Fe-Sn alloy layer and the effect of heating rate will be published shortly.

Jan 1, 1965