Search Documents

By C.P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By C. P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By B. B. Zavoico

During 1936 the Russian oil industry made very satisfactory progress and, while not all difficulties of organization have been ironed out, the country is now assured of a supply of petroleum products in sufficient quantities and of quality demanded by modern motor equipment. The year 1937 promises to better by a wide margin the good showing of 1936. The statistics given in this paper for the first time take into consideration the varying gravities of crude oils of the several Russian oil fields instead of using a flat conversion factor of 7 bbl. per metric ton. It was found from the detailed study that the generally used average conversion factor should be increased from 7 to 7.25 bbl. per metric ton, the figure varying, of course, with the gravity of oil in the individual fields. Crude-oil production during 1936 is estimated at 201,500,000 bbl. as compared with 182,970,000 bbl. produced in 1935, an increase of 9.4 per cent. The greatest increase was again recorded in the Baku district, which increased its production by 10.9 per cent, from 141,257,000 bbl. in 1935 to 158,300,000 in 1936. Grozny district maintained its production at a level of about 23,000,000 bbl., but its old fields continued to decline and production was sustained by the development of newer fields. A great advance was made in drilling speeds and the total footage in 1936 reached 6,694,200 ft. as compared with 4,926,600 ft. drilled in 1935, an increase of 26.4 per cent. In older deep fields, producers were being completed at over 8000 ft.—a great depth for Russian drillers but two years ago. Several major discoveries were made in 1936. Northeast Caucasus.—Izberbash, east from Grozny and on the Caspian Sea, was the outstanding discovery, the initial production of the discovery well being around 3000 bbl. per day from about 5000 ft. The importance of the field is due to the large area of the structure, half of which, however, is under the sea, and also to its strategic location on the shores of the Caspian and near a trunk pipe line to the Grozny refining center. An active development program is being pursued in Izberbash and its 1937 production quota is set at 7,500,000 bbl. Achi-Su field, near Izberbash, also discovered during 1936, while not as prolific as Izberbash, is thought to cover a very large area and the small

Jan 1, 1937

P. H. Dudley, Yew York, N. Y. (communication to the Secretary*) :—The characteristics of Professor Home's metallurgical papers are, that he is able, from the mass of confusing evidence on the subject, to make an analysis and present hypothetical and essential principles in concrete form for consideration and discussion. I can appreciate, from the practical side of the subject, the labor of collecting and investigating the data which was essential to prepare the paper. Much of it necessarily came from material of preceding years of manufacture in which time was allowed for chemical reactions of the re-carburizer, and for the elimination of the oxidation-products before teeming the ingots. This practice gave a favorable time-element to free the metal from slag and other impurities— a requisite condition for the production of sound steel in the ingots. But, in allowing them to become cold before they were charged into the furnace, a subsequent time-element entered as a detrimental factor in the development of the pipe or shrinkage-cavities, which gave an ingot-structure deficient in soundness, at least in the upper portion. (The term slag is used in a general rather than in a strictly technical sense.) Traces of manganese sulphide are often associated with manganese silicates in the same thread or seam, and at other places they are separate and distinct. Interpretations from material thus manufactured must be made with due allowances for the methods of fabrication and the requirements of service. The only way we now have to estimate what the degree of soundness of the ingot-structure was, in the early foreign and American manufacture of steel rails, is by examination of the worn and failed material after years of service. We must remember also that the poorest material was long since consigned to the scrap-heap without any full record of its history. The rails from a given ingot cannot now be identified ; and in many

Jan 1, 1909

By J. H. Bechtold

Tensile properties of annealed molybdenum were investigated from 1000" to—200°C. In the vicinity of room temperature a well-defined transition in tensile properties occurs. Reduction in area decreases from over 80 pct to 0 pct and, simultaneously, the yield strength increases about 60,000 psi. MOLYBDENUM, tungsten, iron, and many other metals and alloys with the body-centered cubic and hexagonal close-packed crystal structures change from ductile to brittle behavior over some relatively narrow temperature range. The temperature at which this transition in ductility occurs depends on chemical composition, microstructure, and method of testing. When fine grained, completely recrystallized molybdenum of commercial purity is tested in uniaxial tension at a slow strain rate, the transition occurs at slightly below room temperature.' Iron2 and tungsten3 tested under similar conditions become brittle at temperatures close to the boiling point of nitrogen, — 195°C and at about 200°C, respectively. A sharp change in ductility is uncommon in metals with the face-centered cubic crystal structure, however, a relatively sharp transi- tion in notched bar impact properties has been observed below room temperature in a face-centered cubic copper-antimony alloy.4 A transition from ductile to brittle behavior is usually explained by the concepts originally developed by Ludwik,5 and discussed and elaborated on by others including Orowan,6 Hollomon and Jaffe,7 and Gensamer8 In brief, there are two aspects to strength, first the resistance to flow and second the resistance to fracture. Both are functions of temperature, strain, strain rate, stress system, composition, and microstructure. With decreased test temperature the flow stress required to initiate plastic deformation increases more rapidly than the fracture strength and brittle fracture occurs at that temperature where the yield strength equals or exceeds a brittle fracture strength. This investigation was conducted to determine the effects of temperature, strain, and rate of straining on the flow and fracture strengths of molybdenum above, through, and below the ductile-to-brittle transition. Other variables were held constant during testing. This information is believed to show

Jan 1, 1954

By B. S. Old, E. R. Poor

PRODUCING more steel without major capital investment in new plants is one of the most perplexing difficulties which confront the nation's postwar steel industry. The lack of scrap at a reasonable price results in an especially heavy pressure being brought to bear on the pig-iron production facilities which consist of 245 blast furnaces scattered throughout the country but concentrated most heavily in the Pittsburgh-Chicago area. Present demands exceed the total optimum output of these existing blast-furnace plants. Management hesitates to authorize erection of new plants on a scale sufficient to satisfy 'the demand for pig iron for two main reasons: first, extensive building under the present high costs of construction would greatly increase . the over-all capital investment per ton of iron capacity; and, second, the amount of steel necessary for a major construction program would upset the already tight supply-demand situation. The answer to the problem would then seem to be the development and application of a method which would increase the capacity of existing blast furnaces with a minimum of alterations and expense. Experiments consisting of operating a blast furnace at higher-than-normal top pressures, as proposed by Arthur D. Little, Inc., were carried out by the Republic Steel Corp. initially during World War II, and much more extensively during the past twenty months. The results of the Republics trials indicate that pressure blowing is a solution to the problem of increasing pig-iron capacity without necessitating major changes to existing equipment.

Jan 1, 1948

By V. F. STANLEY

THERE is not the slightest doubt that the present recoveries of valuable minerals by the Broken Hill mills could be improved, and that further machinery would be installed for the purpose if it could be assured that a high price of metals would be maintained; but concentration, like all other com¬mercial propositions, is a question of profit and loss, and no sensible metallurgist would carry out his work in such a manner as to obtain high recoveries at a financial loss to his company. There is a point in all concentration at which the added money obtained from the higher recovery of minerals is balanced by the extra cost of obtaining the last part of the recovery; a wise metallurgist will be content with his work before his working-expenditure reaches this point. To a casual observer, the work being done by the various Broken Hill mills is identically the same. A closer investigation will show that this is far from being the case, for it is a remarkable fact that, although the larger mines extend over a length of approximately only 2 miles, such a difference in the physical and chemical properties of the ores exists that, from the first reduction downwards, special treatment is necessary in each case, and hardly any two mills are identical in operation. The details of this paper refer directly- to the work of one . particular mill in Broken Hill, for the reason that the ore from each mine presents special difficulties and requires its own special treatment. I have selected the mill referred to because it has been constructed and modified under my supervision.

Sep 1, 1909

By John Howe Hall

One's first thought, upon being chosen to deliver the Henry Mario Howe lecture, is of pride at being selected for this post of honor, but ther succeeds immediately a deep sense of the Obligation thereby incurre to give of one's very best in order to make a contribution worthy of hir in whose memory these lectures are given. One who had the goo fortune to be associated with Henry ill. Howe, upon sitting down t prepare such a paper as this, irnrnediately falls to musing upon thc day when his face and his footfall were familiar from constant association, an recalls with singular vividness his active figure, his mobile, alert face, an his keenness in penetrating to thc corc of the subject under discussior Like Dr. Mathews, I was a young man when I first worked under hi direction, now nearly a quarter of a century ago, and in those early day he oft,en seemed a hard taskmaster—a man whose standards it woul never be possible for me to meet. I well recall his insisting upon m proving for the third time the truth of a conclusion which I had brc unwilling to submit to him until it had been confirmed by two carefull planned experiments. To my impatient protest that thc third .demor stration he asked for was but a repetition of the second, with differer samples, he replied, "Yes, that is true, but the inherent improbability ( your conclusions is so evident that I can not accept them until you prov your case again." "Shall I ever do a thing well enough to suit him? I thought. Looking back today upon many similar incidents, 1 suspect that h never expected me to attain the excellence he preached, and held up t me and to himself as a model, but knew out of the fullness of his experienc. that in no other way could he so impress upon me the necessity in researc of the patient, never-failing attention to detail and to accuracy tha distinguished his own work. How painstaking he was in the preparation of his many books an professional papers, as well as in his experimcntal work, was ncvcr s

Jan 1, 1929

By Archer E., Wheeler

Producing copper companies were active during 1941 owing to the national defense program the United States and the requirements of the friendly belligerent nation. This activity extended to the American owned properties in South America, the major part of whose product was taken by the Metals Reserve Co., a U.S. Government agency. Anaconda Copper Mining Co. is building a new converter plant at Anaconda, with four units of the Peirce-Smith type. The addition is being built adjacent to the reverberatory plant so as to avoid the necessity of hauling matte and slag. It is expected to be completed this year.

Jan 1, 1942

By I. C. Edwards, W. J. Dengler, D. F. Lillie

By 1959 the milling plant of Bicr oft Uranium Mines Ltd. had been in operation for two years. During this time many changes, both physical and chemical, had been made in an effort to improve plant efficiency. Investigational work had been facilitated greatly by the fact that the Bicroft mill consists to a large extent of two parallel circuits; however, the number of interrelated variables is great, and it is difficult to measure, let alone control, all of them simultaneously. The Bicroft mill staff feels that much progress has been made, but there is much yet to be done and many questions still to be answered. The Addendum outlines noteworthy developments to the fall of 1960. The property of Bicroft Uranium Mines is located in Cardiff Township in the Highlands of Haliburton County, southeastern Ontario, some 140 miles northeast of the city of Toronto and 70 miles due north of Lake Ontario. The ore-bearing dikes are classed as mafic. nonsegregated, syenite and granite pegmatite. Microline, microline perthite, quartz, sodic plagioclase, and pyroxene or biotite are the main constituents with uraninite, uranothorite, fluorite, titanite, cryolite, calcite, pyrite, pyrrhotite, and molybdenite as important accessories. The mill was designed for a nominal capacity of 1000 tpd with all sections except grinding, leaching, and clarification capable of 1500 tons. Feed was entered to one mill unit on Oct. 29, 1956, and to the second parallel line on November 13. The total feed rate was at 1000 tpd on November 15. The first precipitate was produced on November 12. By August 1958 the average entry had been increased to 1410 tpd without the installation of any additional major equipment. The overall recovery has been greater than 93.0 pct on several months, but a recovery of 92.5 pct appears to be most economical. Operating time for eight months in 1958 has been 97.1 pct although all grinding mills were relined during this period. A generalized flowsheet is shown in Fig. 1 and the plant layout in Fig. 2. The ore is crushed in three stages to -3/8-in. and then is wet ground in two stages to approximately 50 pct -200 mesh. The pulp is thickened to 68 pct solids and agitated by air for 33 hr at a pH of 1.9 as maintained by the addition of 93 pct sulfuric acid. Separation of the uranium-bearing pregnant liquor from the residue is accomplished by five-stage countercurrent decantation (CCD), following which the liquor is clarified for removal of fine slimes. The clarified liquor is treated in the ion exchange equipment in which both the upgrading of the solution and the removal of some impurities is accomplished. Addition of magnesia to the high-grade eluate from ion exchange precipitates the uranium as sodium-magnesium diuranate. After being filtered and dried this precipitate is packaged in drums for shipment. The residue from CCD and the barren solution from ion exchange are neutralized by the addition of lime and pumped to the tailings disposal area. CRUSHING All crushing is done on surface in a conventional three-stage unit consisting of a 36x48-in. Birdsboro Buchanan jaw crusher, a 4 1/4-ft standard Symons cone crusher, and a 4-ft Symons shorthead. Both the two primary and the two secondary screens are 4X 8-ft Symons rod decks. Moisture content of the feed ranges from 3 to 4 pct. In the initial installation the primary screens were equipped with 5/16-in. rods at 1 1/4-in. spacing and the secondaries with 5/16-in. rods at 1/2-in. spacing. With this arrangement the average crushing rate was better than 180 tph. To reduce the work required of the grinding circuit as tonnage was increased, several changes were made in the crushing circuit. By September 1957, both secondary screens had been reduced to 3/8-in. spacing, and rod size had been reduced to 3/16-in. to provide increased open area. Average throughput was reduced to 160 tph. Later, 50 pct of one primary screen was decreased to 1/2-in. opening to better balance the load between the two cone crushers. In May 1958,

Jan 1, 1961

By M. J. Pool, with Appendix by Larry Kaufman, R. W. Krenzer

Thermodynmic properties of the Cu-Mn system have been deterrrzined in the temperature range 973" to 1273°K by measuring the vapor pressure of manganese in equilibrium with alloys of compositions varying from 0.13 to 0.91 rnole fraction manganese using the Knudsen effusion technique. Activities of manganese calculated from the measured vapor pressures show large positive deviations. Calculated heats and entropies of mixing are positive with a maximum occurring at approximately 0. 7 mole fraction manganese. ThE investigation of thermodynamic properties of binary systems involving transition metals is of considerable interest at the present time. The incomplete subvalency electron levels of transition metals lead to unusual behavior in some alloys, and considerable information can be obtained by determining the thermodynamic characteristics of these systems and relating the thermodynamic behavior to observed physical properties. The Cu-Mn system, shown in Fig. 1,' provides an example of an alloy system in which the determination of the equilibrium phase diagram and various physical properties has received considerable attention, but very little work has been done on measurement of the thermodynamic properties. Elemental copper and manganese have comparable electronegatives, atomic sizes, and cohesive energies, but differ in crystal structure. They form a continuous series of solid solutions only at high temperatures and the structure varies in a continuous manner from fcc at the copper-rich end to fct at the manganese-rich end.' The purpose of this investigation was to measure the vapor pressure of manganese over a series of Cu-Mn alloys and from these values determine the thermodynamic properties of the binary system. Vapor pressure measurements were made in the temperature range 973" to 1273"K, remaining within the solid-solution region for each alloy studied. EXPERIMENTAL PROCEDURE The relative thermodynamic properties of solid Cu-Mn alloys were determined from vapor pressure measurements by means of the Knudsen effusion tech- nique. Several discussions of the theory can be found in the literature. In the case of copper and manganese, it is assumed that manganese is the only component subliming, so the vapor pressure of manganese over the various alloys can be determined directly by measuring the weight loss of the effusion cell. This is a valid assumption since the vapor pressure of manganese is about four orders of magnitude higher than the vapor pressure of copper in the temperature region of interest. The vapor pressure of manganese over the alloys at any given temperature is then related to the weight loss of the effusion cell per unit area per unit time. An upper limit of 1.5 x 10"s has been measured for the ratio of polyatomic to monoatomic molecules for manganese vapor in equilibrium with solid manganese at 1180°K, so it was assumed that manganese vapor is monoatomic. The effusion cells, fabricated from high-purity alumina, are 26 mm high, 18 mm OD, and have a wall thickness of 1 mm. Three different sized holes of 2.03, 2.54, and 3.18 mm diam were drilled in the lids from the inside face to minimize chipping, and the lids were then slip-cast onto the cells to provide a gas-tight seal. Alumina was selected for this particular application both because of its resistance to thermal shock and reaction with manganese vapor. In the ideal case, the orifice of the effusion cell should have a knife edge so that effusion through the orifice

Jan 1, 1970

By Dudley L. Davis, E. C. Peterson

Introduction The Darwin District is 30 miles east of Olancha which is 220 miles north from Los z4ngeles via U. S. Highway No. 6. The ore deposits occur in the Darwin hills that have been elevated above the Darwin plateau by typical basin and range-type faults. Some of these faults have been active quite recently as shown by the displacemerit of Quaternary (?) basalt flows and the rejuvenation of erosion in Darwin wash. The ore bodies occur as fissure fillings and replacement of favorable beddings in a thick series of Paleozoic limestones, dolomites, shales and quartzites. Rich oxidized lead-silver ores were dis'Overed in the early seventies. BY 1875, Darwin had a population Of about 5000, and by 1880 several small mills and smelters had been built. Early exhaustion of surface ores, the isolated location of the district, and fluctuation Of metal prices caused intermittent operations until World War 11. The district production is estimated at about $3,000,000 prior to 1900 and perhaps $4,000,000 between 1900 and 1945 when Anaconda purchased the major producing mines. 'or the Past two Years, daily production has averaged 75 tons of direct shipping and 150 tons of milling-grade ore. At present, 300 tons of mixed oxide and sulphide ore are treated by flotation, the oxidized lead minerals being activated by addition of sodium sulphide after galena and sphalerite have been recovered from the circuit. Extraction averages 85 pct of the lead, 80 pct of the silver, and about 33 Pct Of the zinc in a bulk concentrate. The mill is designed so that minor changes permit selective flotation of pyritic lead-zinc ores encountered at depth. General Geology The oldest rocks in the Darwin hills are a series of Paleozoic limestones, dolomites, shales and quartzites probably pennsyl-vanian in age. These rocks have been intruded on the Rest by the Coso granite batholith and on the east by a granodiorite stock. Numerous sills and dikes grading from orthoclase granite to gabbro are exposed in the underground workings. The sedimentary rocks have been considerably folded and faulted, the most prominent structure being a northwest pitching anticlinal fold, the crest of which lies just west of the ridge line of the Darwin hills, The east limb of this fold has been intruded by the granodiorite stock and east of the stock the sediments show several closely spaced anticlines and synclines. The minor flexures on the west flank of the major fold are structurally important in localizing the ore in the Defiance and Essex mines of the Darwin group. There are three principal systems of faulting and fissuring, most of which are post-intrusive and premineral in age, with minor amounts of postmineral movement. The Darwin tear fault is the largest, most persistent fault in the district. It strikes N 60 to 75°W, dips steeply south and is traceable for about 10 miles. It is a normal

Jan 1, 1949

R. L. Fleischer (Department of Metallurgy, Massachusetts Institute of Technology)— The authors have presented valuable observations of oehavior of aluminum at intermediate and high temperatures. I should like to consider their interpretation of the appearance of cross slip plane traces in sample B-3 as partly due to "bending of the crystal due to grip constraint." Because bending moments might be set

Jan 1, 1960

By E. J. ENGEL

The New York talc deposits of commercial importance are in St. Lawrence and Lewis counties, in the northwest Adirondack Mountains (Fig 1). All of the deposits are of pre-Cambrian age and occur within highly deformed and recrystallized marble of the Grenville series. The deposits in St. Lawrence County, near Gouverneur, are the largest and most productive of their type known in the Western Hemisphere. In 1948 the seven mines which are in operation will produce about 130,000 tons of ground talc. All talc production in Lewis County is from one mine. There the annual production ranges from 15,000 to 30,000 tons. These so called talcs of New York State include earth materials of differ- ent chemical and mineral compositions. In general the mineral talc is sub- ordinate in amount to other minerals in both the Gouverneur and Natural Bridge deposits.

Jan 1, 1949

INTO their great Pacific Northwest counting house went the members of the Industrial Minerals Division recently, to count their blessings amidst the scenic grandeur and mineral wealth of the State of Washington. From their vantage point in Seattle, those who attended the IMD's fourth Pacific Northwest meeting turned their sights to the South and Southeast, scanned Montana, Idaho, Oregon and Utah, and predicted a very healthy economic future for their region. The praises of Idaho's booming phosphate industry were sung by Earl W. Murphy, secretary of that State's Chamber of Commerce. He said the establishment of Fort Hall, on the banks of the Snake River near Pocatello, first turned the eyes of the world toward what is now the center of the greatest known deposits of phosphate rock-the section adjacent to the common corners of Idaho, Wyoming and Utah. With the founding of Fort Hall, Mr. Murphy said, historians will also rank the construction of the first electric furnaces for the production of elemental phosphorous as equally significant in the commercial history of the West. Those furnaces were installed only last year by the Westvaco Chemical Div. of the Food Machinery & Chemical Corp. at Pocatello, at a cost of $8 million.

Jan 7, 1950

By AIME AIME

BY COMBINING the sessions on reduction and refining of copper, lead and zinc it was possible to devote an entire day to nonferrous metallurgy. Four interesting papers were presented at the morning session and four more in the afternoon. In the discussion of papers on copper, F. R. Pyne acted as chairman, with H. M. Shepard as vice-chairman, whereas for those on lead and zinc, F. F. Colcord acted as chairman, with C. R. Hayward as vice-chairman. The paper by P. D. I. Honeyman on the smelting of raw concentrates in the reverberatory furnace was presented by Mr. Pyne and discussed by Messrs. Mazany and Hayward. The interesting paper by E. S. Bardwell, com- paring the use of various fuels in copper-refining furnaces at Great Fails, Mont., was presented by Mr. Shepard and discussed by Messrs. Boggs, Gronningsater and Hayward. That by R. G. Knickerhocker, describing the stationary basic copper converter at Messina, Transvaal, was presented by Mr. Pyne, together with a written discussion by c. R. Kuzell, of the United Verde Copper co. It was an interesting illustration of how well-known processes may sometimes be modified to fit into unusual conditions.

Jan 1, 1932

By Charles H. Morgan

THE case of Henry Cort comprises: (1) the nature of Cort's inventions;, (2) their value to England and to mankind,; (3) the remuneration received therefor by him or his family; and (4) the suitable permanent record and recognition of his services by the representatives of the art lie founded-a debt long over-due, and still unpaid. I. CORT'S INVENTIONS. Under this head, it is unnecessary here to enter into details. The facts have been repeatedly published, and a brief outline of them will be sufficient for my present purpose. . Henry Cort, born in 1740 at Lancaster, England, became a navy broker in. London about 1765, and gained from that business in about ten years. something more than £20,000, which lie devoted to perfecting the manufacture of iron, building a mill at Fontley, near Portsmouth, and prosecuting, between 1777 and 1783, the experiments which culminated in .his two patents, one for puddling iron and the other for shaping it by rolling between grooved rolls.: Careful study of the contemporary evidence, including Cort's specifications, the testimony (in act as well as word) of his business rivals, the public declarations of eminent authorities, and the history of the times, leaves no possible doubt that Cort was the real inventor, of

Mar 1, 1905

By Rossiter W. Raymond

(Chattanooga Meeting, October, INS.) THE formal outline of Mr. Hague's life and work is embraced in the following statement, chiefly based upon data furnished by him, at my request, shortly before his death. At that time the probability that I would survive to record his death was apparently small; but I urged upon him the duty of providing, whether for me or for my successor as Secretary of the Institute, trustworthy material for the notice which somebody would some day have to write-and which might otherwise be incomplete or incorrect. Mr. Hague, with characteristic promptness and freedom from affectation, did what I asked of him; and I am therefore . able to present an authoritative sketch-concerning the details of which I shall add my own comments, and some particulars obtained from others of his personal friends. James Duncan Hague was born Feb..24, 1836, at Boston, Mass., where his father, Rev. William Hague, D.D., an eminent clergyman, then resided. After a preliminary, education in private. schools, be studied in 1854 at the, Lawrence Scientific School of Harvard University; in 1855 and 1856 at the University of Göttingen, Hanover; and from 1856 to 1858 at the Royal Mining Academy of Freiberg, Saxony. In 1859-1861 he was attached as chemist to a South Sea exploring expedition, sent by W. H. Webb, of New York, to examine Jarvis, Baker, and other islands for phosphate-deposits. After the outbreak of the Civil War, he entered the U. S. Navy, serving for a year as Judge Advocate to the fleet stationed at Port Royal, S. C. In 1863 he became Superintendent of the Albany and Boston copper-mine, in the Lake Superior region, where he was also connected with the earliest development of the Calumet and Hecla property. In 1867 he became the First Assistant Geologist in Clarence King's famous Exploration of

Feb 1, 1909

By Thomas R. Stauffer

The principle that conventional schemes for taxing petroleum or mineral resources are "inefficient" is illustrated using simulation calculations tested against an "ideal" system. Inefficiency is defined as the relative success in maximizing expected government revenues from the resources. Most systems fail because: 1) they leave oil in limbo, i.e. unproduced because of excessive fiscal burden; or 2) they unnecessarily increase the variance in the explorationist'c, rate of return by undertaxing large fields and overtaxing smaller but infra-marginal fields. This increases his discount rate and reduces taxable surplus. An "ideal" tax system is specified which maximizes government revenues while minimizing risk to the operator. Two criteria are developed: 1) the tax falls to zero on fields which yield only the minimum necessary rate of return ("marginal" fields); and 2) the after-tax present value of all fields is the same for all fields above a threshhold size. In particular, marginal fields, while contrib- uting little to expected values, do contribute to reducing variance and hence risk praemia by distributing the exploration costs over a higher probability of successful outcomes.

Jan 1, 1982

By Philip D. Wilson

SPEED is essentiaI in this war program and it is hard to keep up with developments. When the title of this paper was chosen, the contemplated magnesium production for which plants were then under construction was some 200,000 tons of metal per year or sixty times the 3350-ton production in prewar 1939. A few- days later an analysis of the President's 185,000-plane pro-gram, incendiary bomb schedules, and the additional requirements of the Army. Navy and Maritime Commission made it apparent that a much greater amount of magnesium must be provided in 1943. The new figures are huge but the censor will not per-mit their disclosure.

Jan 1, 1942