Search Documents

By M. S. Burton, G. V. Smith, A. Rosen

The kinetics of re crystallization and the effect of recovery on recrystallization of pure iron were investigated within the temperature range of 517" to 632 OC. Grain growth and activation energies were also studied. Two stages can be distinguished during recrystallization; the first is gvowth-controlled and the second is nucleation-controlled. The extent to which the first stage succeeds before the second stage begins depends on both temperature of recrystallization and temperature of recovery. The softening of cold-worked metals and alloys due to transformation of the deformed crystals to strain-free equiaxed grains during annealing is well-known, and early inestiators established that recrystallization kinetics is strongly influenced by minute quantities of impurities. Generally, it is believed that impurities decrease the rate of recrystallization and the rate of grain growth. To understand the basic phenomena of recrystallization, investigations should be on pure materials. Most of the research on high-purity materials has been on metals having the fee Bcc materials, and especially high-purity iron, have been studied only in recent years. It is known that recovery may influence recrystalliation;" however, no general description of the influence, applicable to all materials, has been presented. This paper presents results of a study of the recrystallization kinetics of high-purity iron, after 60 pct cold deformation by drawing, with particular reference to the influence of recovery on the rates of recrystallization and grain growth. From observations of these rates, conclusions are drawn concerning nucleation. MATERIAL AND EXPERIMENTAL PROCEDURE Preparation of Material. High-purity iron, prepared by zone refining of vacuum-melted electroiytic iron at Battelle Memorial Institute under sponsorship of the American Iron and Steel Institute, was used in this study. Table I gives the reported chemical analysis of the material, taken at a point near the last molten zone and thereby rep- resenting the maximum impurity level for the entire bar. Prismatic specimens, approximately 10 x 10 X 50 mm, were sawed from the 50-mm-diam bar, perpendicular to the zone-refining direction, and turned to cylindrical shape. These specimens were sealed in quartz capsules under vacuum, approximately 10"e mm Hg, austenitized at 930° C for 15 min, slowly cooled, removed from the capsules, and cold-worked in air by swaging to approximately 20-pct reduction of area. The encapsulating, austenitizing, and swaging operations were repeated two additional times, after which the samples were encapsulated, austenitized, and cold-drawn to 60-pct reduction of area. A further vacuum anneal at 630°C for 120 min and cold drawing to 60-pct reduction of area produced wire 2.8 mm in diameter. The drawn wire was electropolished to remove deformed material on the surface, after which it was sawed into 4-mm-long specimens for the recrystallization study. Microscopical examination before the final cold reduction revealed equiaxed grain structure with very fine grains in a thin layer near the surfaces of the specimen and nearly uniform ASTM 3-4 grain size in the center. Recrystallization Heat Treatment. a) Direct Recrystallization of Cold-Worked The 60 pct cold drawn iron specimens were recrystallized at five temperatures, 517, 556, 590°, 612, and 632C, in a lead bath covered with graphite (the temperature was controlled to 1°C). Specimens were treated for twelve different times at each temperature, and all were water-quenched after heat &eatment. b) Recrystallization Following Preliminary Recovery Heat Treatment. After cold working, specimens were sealed into quartz capsules under vacuum, 105 mm Hg, and recovery-annealed at 362", 400", and 440°C for 20 hr prior to recrystallization. No evidence of recrystallization was found

Jan 1, 1964

By W. H. Herrnstein, J. B. Clark, E. C. Utley, A. J. McEvily

The ratio of the endurance limit (10' cycles) to tensile strength of age-hardened aluminum alloys is approximately 0.3, whereas the ratio for annealed alloys is about 0.5. The lower value for the age-hardened alloys has been associated with the instability of coherent precipitate during cyclic loading, but it has not been definitely established whether this instability is due to overaging or reversion during cyclic loading. The results of the present investigatzon support the reversion viewpoint. In this work specimem of 2024-T4 aluminum alloy were aged for 16 hr at 150°C after cycling for 10 pct of the life at 25.000 psi. These specimens were then tested to failure and exhibzted a marked increase in fatigue life. It is proposed that during the early stages of fatigue in this alloy dislocations cut through the coherent precipitate and bring about the reversion of the precipitate. Subsequent aging at 150ºC induces reprecipitation in the precipitate-free zones so that the weakened regions are strengthened and the fatigue life is extended. It Is recognized that the fatigue strengths of precipitation hardened aluminum alloys are unusually low relative to their tensile strength.'-= This feature is illustrated in Fig. 1 where it can be seen that age-hardened alloys have lower fatigue ratios (the ratio of the fatigue strength to the tensile strength) than those in the annealed or cold worked state. Further, as shown in Fig. 2, the more an alloy is dependent upon precipitation hardening for its total strength, the lower is the ratio of the fatigue strength to the tensile strength. This state of affairs has been associated with an instability of the metastable metallurgical structure of precipitation hardened aluminum alloys during cyclic loading. Evidence2 in support of this view is that the fatigue ratio increases in these alloys as the test temperature is lowered, thereby indicating that thermo-mechanical instability, rather than some other factor such as a non-uniform distribution of precipitate, is the factor responsible for the low fatigue ratio at room temperature. Two mutually exclusive proposals have been ad- vanced to account for this instability. Hanstock has proposed that overaging takes place during cyclic loading, and in support of this view, Broom et a1.2 have indicated that an overaging process might be promoted by the large numbers of vacancies which are created during cyclic loading. The creation of vacancies by radiation4 has been shown to lead to rapid overaging. Hanstockl obtained visual evidence of overaging in an aluminum alloy after cyclic loading, but in this instance it has been pointed ou? that because of the high frequency used (60,000 cpm) the observed effect may have been due to normal high temperature precipitation around energy dissipating cracks. Efforts to discern visual evidence of overaging in this alloy at lower test frequencies were not successful.3 The alternative postulate3 is that reversion takes place during cyclic loading and leads to localized soft spots at which fatigue cracks are readily initiated. Evidence for this process has recently been provided by Polmear and Bainbridge5 who demonstrated metallographically that regions depleted of precipitate were created during cyclic loading of an aluminum alloy. Inasmuch as precipitate particles bordering the depleted region had not grown in size, it was concluded that the solute atoms which had constituted the missing particles had gone back into solution. No mechanism for the reversion process was presented. The present study was undertaken to investigate further the conditions leading to instability during cyclic loading, and to determine whether reversion or overaging had taken place as a result of cyclic loading. BACKGROUND AND TEST PROCEDURE In order to differentiate between the processes of reversion and overaging, rest periods at an elevated temperature, which ordinarily would insure additional precipitation, were used in this investigation. It was expected that after a period of cyclic loading an elevated temperature rest period would result in a decrease in the remaining life of the specimen if overaging were occurring during cyclic loading, whereas in the case of reversion, reprecipitation would occur and the fatigue life would be extended. Such an expectation is based on the assumption that the crack-nucleation phase is a significant portion of the total fatigue life, and that such a treatment is of influence in the crack-nucleation stage and is relatively unimportant thereafter.

Jan 1, 1963

By H. W. Weart, D. J. Mack

SINCE the first recognition of eutectic solidification as the simultaneous formation of 2 solids from one liquid,1 many complex structures thus produced have been observed. Despite many attempts to ascertain it, however, the detailed mechanism by which these structures develop remains obscure. In an attempt to clarify the origin of eutectic structures, the study described in this paper was undertaken. The broad objective of the study was to investigate the effect of different solidification conditions on the structure of single eutectic grains. It was expected that the eutectic structure would thereby be isolated for study, but preliminary experiments revealed another structure within each grain. When a literature surveye revealed only 1 previous mention of the subgrain structure,' it was decided to determine the origin of the structure and to study its response to various growth conditions. Before presenting the details of the investigation, it is apropos to distinguish carefully among the 3 structures produced during eutectic solidification. This is especially desirable in view of the apparent confusion existing in the literature concerning the structures in a eutectic specimen. The confusion is due largely to the existence of the subgrain structure noted above which is easily mistaken for the grain structure. In the following paragraphs, an effort is made to distinguish the 3 structures by briefly describing their origin during solidification, even though the results are thereby anticipated slightly. The 3 structures produced during eutectic solidification are the grain structure, the colony structure, and the eutectic structure, each one contained by the one preceding it. The grain structure is analogous to the polycrystalline structure of a metal or inle-phase alloy in that each grain grows from a single nucleus. A somewhat broader interpretation is needed here, however, because of the presence of 2 phases in each grain. Since in most eutec-tics particles of 1 phase are dispersed in a matrix of the other, a grain may be taken to be the region in which the matrix phase is monocrystalline.*

Jan 1, 1959

By S. R. Goodman, Hsun Hu

The rolling texture transition in copper as a function of deformation temperature is found to be quite similar to that in high-purity silver. The ordinary copper type texture changes gradually to the brass type, accompanied by an increase in the stacking fault frequency, as the temperature of deformation decreases. The rolling textures obtained at low temperatures and the corresponding annealing textures compare remarkably well with the ordinary rolling and annealing textures of low-zinc brasses. Furthermore, it is also found that the observed stacking fault energies of copper specimens deformed at low temperatures correspond closely with those of low-zinc brasses, as deduced from measurements of the dislocation nodes. These results are consistent with the idea that texture transition may be significantly dependent on the stacking fault energy. It was shown in a series of previous publications1"3 that the rolling texture of high-purity silver changes gradually from the common silver type (or the brass type) to the copper type* with increasing temperature *The silver or brass type rolling textures are commonly described as (110)[112],4,5 whereas the copper type rolling textures are mainly (123) [a121 and (146)[211].5 Other ideal orientations have been used by various investigators for the copper type rolling textures, but the actual difference among these ideal orientations is rather small. of deformation, and that such texture transition can be correlated with the change in stacking fault frequency as a function of rolling temperature. Furthermore, it was shown that the formation of annealing textures in high-purity silver from the various rolling textures obtained during the course of texture transition depends entirely upon the deformation texture. From a common silver type or brass type rolling texture (such as produced by rolling at 0" or at 50° C) the recrystallization texture is mainly (120)[211], which is quite different from the recrystallization texture of brass.* However, for both ma- terials the orientation relationship between the rolling texture and the recrystallization texture can be expressed in terms of similar rotations around [Ill.] axes of approximately 30 or 35 deg. They differ in that the [Ill] rotational axes are different. In the case of high-purity silver, the axes of rotation are the two (111) poles near the plane normal of the deformed specimen with a (11l)[112] type rolling texture, whereas in brass, they are the (111) poles near the direction of rolling. For high-purity silver with a predominantly copper type rolling texture (such as produced by rolling at 150° or 200°C) the recrystallization texture is mainly (100)[001], or the cube texture, plus its twin orientations. It was shown previously6 that such reorientation observed in copper or aluminum can be described as [Ill] rotations of 30 to 40 deg. For intermediate cases, i.e., when the rolling textures are composed of a

Jan 1, 1963

By Arthur L. Crawford

PLAGER gold is perhaps the most difficult of the common mineral deposits to evaluate. Not only are the erratic pay streaks a source of never-ending uncertainty, but the spotty distribution of the gold in iso¬lated nuggets is a perpetual source of error and disappointment to the sampler. Experienced engineers have long realized this difficulty and have been wary in predicting assay values except in the most general terms, and then only after extensive and usually expensive sampling. During the past year I have had the opportunity of checking a number of gold placers, and from the results obtained I believe that the microscope may be employed to advantage in placer sampling.

Jan 1, 1933

By F. Forward, H. Veltman, A. Vizsolyi

Activities of oxides in the ternary FeO-MnO-SiO system are calculated from data on the binaries, using the Gibbs -Schuhmann method. These activity data are used, together with thermodynamic relations, to calculate the contents of oxygen, silicon, and manganese in liquid iron, and the composition of the corresponding oxide phases in equilibrium with it. Excellent agreement was found between calculated and experimental metal compositions, indicating that thermodynamic methods, such as those presented, can supply useful data on slag-metal equilibria, and are therefore capable of wider application. When molten steel containing oxygen is treated with a deoxidizer, the product of the reaction is composed of the oxides of the deoxidizing elements together with more or less iron oxide. This assemblage of oxides is presumably very close to equilibrium with the melt since it is formed directly from elements dissolved in it. Therefore, it is likely that metal analyses corresponding to a given oxide phase composition are calculable with considerable precision where sufficient information is available on activities in both phases. The present study was made to test this hypothesis in the case of deoxidation by silicon and manganese. Here experimental data on the relationship among oxygen, silicon, and manganese in the metal phase are available, as are activity data for the MnO-SiO2, FeO-SiO2, and FeO-MnO binary systems. A further objective was to demonstrate in a specific example how gaps in the data may be filled by judicious interpolation, and how the Gibbs-Schuhmann method is applied to obtain activities in ternary systems. The rigorous derivation of the latter, requiring considerable facility in handling partial differential equations, tends to mask the real simplicity of the method, and repel the very engineers and experimenters who would benefit the most from its use. I) GENERAL PROCEDURE Deoxidation of steel with silicon and manganese results in the formation of two phases, metal and oxide. The number of components is four—Fe, Mn, Si, and 0. The phase rule then gives the number of degrees of freedom: If temperature and pressure are fixed, 2 deg of freedom remain. Consequently, it suffices to fix the concentration of two of the components of the system for all the concentrations to be determined and, at least in principle, calculable. The practical problem is then to discover a straightforward method of calculation with a minimum of trial and error solutions. The type of reactions to be dealt with are like the following: Si (in steel) + 2 O(in steel) = SiO2(in oxide phase) The standard free energy of this reaction is readily obtained from the literature, so that the equilibrium constant can be calculated by the expression: Since the metallurgist is concerned with percentages rather than activities, a real solution requires information that will permit activities to be converted to concentrations. This information is fairly adequate for the elements dissolved in molten steel, but is not available for the FeO-MnO-SiO2 oxide system. Therefore, the first step in this study was to find the relation between activity and concentration for the three oxides making up the system. The next step was the calculation of slag and metal compositions that are in equilibrium with one another. As shown by the phase rule, it is sufficient to assume the values of two composition variables in order to calculate the rest. But which two are picked makes a vast difference in how difficult the calculation turns out to be, so that it is necessary to make preliminary trial of several routes to find the easiest one. A convenient method is to begin with the slag, and to pick FeO concentration and that of one of the other oxides. Starting with the relation between oxygen dissolved in the liquid steel and FeO in the slag permits a good first estimate to be made of the oxygen content of the steel in equilibrium with FeO, because the iron content being fairly close to 100 pct, Fe has an activity close to unity. Using this first estimate of oxygen activity, approximate values of the manganese and silicon contents of the melt are readily calculated from the appropriate equilibrium constants. A minor correction for the depar-

Jan 1, 1963

By P. R. Gage, R. W. Bartlett

At high temperatues and reduced oxygen pressuves, molybdenum silicicles oxidize to form SiO(g) vathev than a passivating SiO2 film. This is a sevious problem for low-pressure applications of sili-cide-coated rejvactory tnetals. As oxiclalion pvoceeds, the higher oxidntion potential of silicon initially suppresses oxidation of molybdenum and silicon is depleted near the surface. Eventually, silicon depletion causes secondary passivation (SiO2) mid an active to passiue transition in oxidntion behavior at moderately low pressures. At very low pressures, silicon depletion continues until steady-state oxidation of both silicon and rnolyhdenum can proceed at rates propovtional to their initial stoicliiorrzetvies. Ohsel-vations of 'oxidatiou-rate belzcriliov at temperatures from 1101° to 1700°C and oxygen pressures from 10-7 to 1 at in were made using thermogravimetn'c, X-ray diffraction, and elect?*on-rtric?ro/,vobe techniqrres. The experimental results are in good agreement with calculated lirnits for the various types of behavior that were based on tlievtnochernicnl atzd dffusion rate data for the Mo-Si system. A protective oxide film normally forms during the oxidation of elemental silicon. However, at elevated temperatures and reduced pressures this film is not present and oxidation is rapid. wagnerl has shown that this behavior occurs because SiO(g) is more stable than SiO2. The behavior of the silicides at high temperatures is similar but more complicated. Molybdenum and several silicide compounds are involved and the chemical activity of silicon, or the equivalent silicon vapor pressure, can vary considerably in these phases. Also, diffusion in the silicides resulting from reactions in which a higher silicide is reduced to a lower silicide, or molybdenum containing dissolved silicon, must be considered. EXPERIMENTAL AND ANALYTICAL METHODS Isothermal oxidation experiments were conducted using hot-pressed MoSi2 and Mo5Si3 wafers. Each experiment was conducted at a fixed oxygen pressure by controlling the flow of oxygen in and out of the furnace chamber. Most of the experiments were conducted in a molybdenum-wound tube furnace. Special construction features, including use of a high-purity dense A12O3 refractory tube, permitted operation in high vacuum to 1500°C. Higher temperatures could be obtained at higher working pressures and with a sacrifice of tube lifetime. Temperature was measured with three Pt 6 pct Rh/Pt 30 pct Rh thermocouples and controlled with a proportional controller. Weight changes were monitored with a quartz spring balance. The few experiments, at higher temperatures and low pressures, were conducted in a cold wall vacuum chamber using induction heating with direct susceptance of the sample. Because of the variable levitation effect of the induction coil on the sample, weight changes could not be monitored continuously in these experiments. All samples representing both experimental methods were weighed before and after oxidiation and examined with a microscope and analyzed by X-ray diffraction. The analytical treatment assumes equilibrium at interfaces and uses existing thermodynamic data. For convenience, equilibria are expressed as chemical potentials or as vapor pressures of the gases involved. The resulting differences in equilibrium vapor pressure between adjacent interfaces and between the surface and external atmosphere drive diffusion processes in the solid and gas boundary film, respectively. These diffusion processes govern the rate of oxidation. A bibliography of the sources of thermochemical data for the reactions pertinent to the Mo-Si-O system is given in Table I. Reactions are listed with the sources of free-energy data referenced. Since all of these reactions involve one or more gas species, usually oxygen, a plot of the product-gas chemical potential, -RT In Pg, vs absolute temperature for each reaction is given in Fig. 1. These curves can be used to determine equilibrium vapor pressures or to compare the stability of different compounds in the various gases: O2, Si, SiO, and Moo3,. The data of Table I and Fig. 1 were used to determine the analytical results presented in this paper. EXPERIMENTAL RESULTS The weight changes for three MoSi, samples oxidized at 1500°C are plotted against time in Fig. 2. The treatments were identical except for the indicated variance of oxygen pressure and each curve represents one of three characteristic types of behavior that were observed. The upper curve is an example of passive oxidation, which is defined as

Jan 1, 1965

By F. L. Wolf

THE catenary system of line construction possesses so many desirable characteristics from the operating standpoint that it has wide application for all types of electric traction. Many steam roads are electrifying sections of their lines, and in most cases are operating both steam and electric locomotives over the same track. This' means that the overhead catenary system is subjected to the severe corrosive action of locomotive smoke, and data concerning the resistance of various alloys to this form of corrosion are very desirable from every point of view. Reliable and specific information and data on the subject of corrosion due to steam and smoke from locomotives are extremely meager and, on this account, extensive service tests, together with accelerated tests, have been made on a number of commercial metals and alloys. The observations and data recorded in this paper are the result of a, preliminary test which was started in 1923 and which has been carried on to the present time. The recognition of the need for even more detailed and accurate data has resulted in the undertaking of another test which has been in progress for about a year. The result of this test will be published in due course. Some years ago The Ohio Brass Co. was asked by one of the large steam railroad companies to furnish data on construction details for a catenary system which it was considering for one of its divisions. The selection of, materials which would give the necessary physical characteristics as well as withstand the severe corrosive action of locomotive gases caused electrical railroad engineers considerable concern. At that time, there were available no specific or authentic data on these important questions: no systematic investigation of the problem appeared to have been made, even though its importance was generally recognized. Such observations as had been made were crude in that they had been limited largely to visual inspection which too frequently is most misleading. However, the scattered information which was collected gave important clues as to how best to start an investigation.

Jan 1, 1930

By G. A. Beiswenger

The application of the law of supply and demand to the sale of crude oil is generally conceded, but the motives underlying the buyer's (refiner's) demands are not always obvious to the seller (producer). In some cases this obscurity has led to the conclusion that the refiner may be unnecessarily particular when he selects one crude and rejects another. This preference, however, is very largely the reflection of the refiner's product demands and the quality of the stocks obtainable from the selected crude. The purpose of this paper is to point out critical characteristies of the major classes of refined products and to show how crudes vary in their suitability for such products. With relatively few exceptions, available processing methods and addition agents make it theoretically possible to produce any type of refined product from any crude source, although it may not be economically sound to do so. The widespread application of thermal cracking for converting higher boiling stocks into gasoline is well known. More recently cracking and refining in the presence of catalysts9 have been developed, as well as various processes for polymerizing lighter hydrocarbons into gasolines having desirable characteristics.6 For several years, selective solvents have been applied commercially to refining inferior quality kerosene, Diesel fuel and lubricating oil distillates.3 Improved methods for refining lubricating oils from crude residual4 formerly suitable only for fuel, are now in use and a number of special solvent processes are available for dewaxing lubricating oils to low pour point.5 These improved refining methods have been developed not only to meet the demand for improved product quality but also to enable the refiner to obtain quality products from crude sources that would not yield such products by the older refining methods. In many cases, the utilization of these modern refining tools necessitates an appreciable expenditure for equipment as well as added manufacturing costs, and their application therefore must be justified economically. Despite the availability of such tools, the added processing costs involved and yields obtainable may render their application entirely impractical. To illustrate this point, inspections of typical cuts from various crudes

Jan 1, 1940

By G. K. Manning, E. R. Stein, E. E. Underwood

Columbium, carbon. and nickel additions were made to iron-base alloys with 20 pct CY. The effects on microstructure, precipitation-hardening characteristics, and High-temperature properties were investigated by means of metallographic, hot-hardness, and magnetic measurements. An austenitic alloy consistilzg of Fe-20Cr-14Ni-0.8C-2.5Cb had higher hot-lzaciness at 1700°F than the other alloys investigated. Its favorable standing is attributed to an enhanced interaction of Cb and Cr4C particles dispersed within a stable austenitic matrix. FOR the past 20 years, cobalt- and nickel-base alloys have been used for the more stringent high-temperature applications because of their excellent creep resistance. Although their performance is quite satisfactory, other base materials must be considered for large tonnage, low-cost applications such as for the automotive gas turbine. Iron-base alloys are also used extensively, but at somewhat lower temperatures, primarily because of the instability of particles or because precipitation occurs at relatively low temperatures. Since unusual stability has been reported for Fe-Cb and Cb-C compounds.1-3 it was hoped that effective amounts of these compounds could be taken into solution at temperatures just below the melting range, then precipitated upon reheating. Actually, strengthening was found to occur by both precipitation hardening in some alloys and by phase transformations in others. Among the alloys investigated, that with the best high-temperature properties owes its strengthening to a combination of carbide particle interaction and a relatively stable austenitic matrix. EXPERIMENTAL PROCEDURES Small preliminary melts of about 100 g were made in a vertical Glotube furnace, using alundum crucibles and an argon atmosphere. Alloys weighing 35 lb were melted in a basic-lined induction furnace, also under argon. The compositions of the alloys are given in Table I. The nickel-free alloys were usually ferritic, while those containing nickel were generally austenitic. Depending upon the particular heat treatments, or the combination of alloying elements, two-phase alloys of ferrite and austenite could be obtained. In the following text, however, the nickel-free or nickel-bearing alloys are referred to simply as either ferritic or austenitic alloys respectively. The small ingots were swaged at 2000°F, in steps, to rods of approximately 3/16-in. diam. The large ingots were forged at 2100°F to 1-in. sq bars. No difficulties were encountered in swaging or forging any of the alloys to as much as 90 pct reduction in area. For heat treating at temperatures above 2000°F, specimens were sealed in quartz tubes under a partial pressure of helium. No special precautions were found to be necessary at lower temperatures. Intermetallic compounds in the preliminary alloys were identified by means of X-ray diffraction measurements. Correlation of these results with micro-structural characteristics (such as color, shape, size, and location) of the compounds aided in their identification. Magnetic susceptibilities were also obtained at room temperature with a Magne Gage instrument after the various heat treatments. To

Jan 1, 1962

By Kenneth S. Ritchie

TOO often, many foremen; superintendents, managers, and executives, "The Bosses" of the oil and mining industries, do not fully realize: (1) How much personal actions '.on the job" may reduce their effectiveness in getting work done; and, (2) The importance of harmonious relations with their fellow men. Today. these qualities of personality in the people entrusted with the positions of responsibility are more important than ever with the shortages of labor so critical in vital war production. Likewise, many engineers do not fully realize that their work is essentially executive in character; i.e., other people do the actual labor. Without their help. the engineer's work would not be done. A clearer appreciation of this fact would increase their interest: (1) in the nontechnical aspects of their work. and, (2)in their relations with others, particularly the individuals in their own organization. Consequently, these engineers would be more successful in equipping themselves for greater responsibilities and increased remuneration.

Jan 1, 1944

By J. P. Witherow

The plant of Messrs. Oliver Brothers and Phillips, the only one in operation until January, 1886, has not been available for any further experiments since those of Mr. R. W. Hunt, described in his paper on the subject, at the Chattanooga meeting. Continuous working has, however, led to important improvements in plant, and furnished valuable results in practice. The difference between the converter and plant of 1884, as illustrated in our Transactions, vol. xiii., p. 759 and following pages, and those of 1885, may be observed in Plates 1. and 11. accompanying this paper. Plate I. gives the elevation and plan, in half-section, of one of our latest 3-ton converters. Plate 11. gives a plan of the general arrangement of a plant adapted to turn out slabs, blooms, and billets for the general market. The letters on Plate I. refer to the following parts :

Jan 1, 1886

By B. D. Cullity

A distribution of residual stress after plastic elongation is proposed, in which the bulk of the material is strained in compression and a very small portion in tension, This distribution is shown to account both for the X-ray observations and for the effect of plastic straining on magnetic losses in silicon steel. The regions left in compression are tentatively identified with the interiors of the sub-grains revealed by the electron microscope. THIS paper is concerned with the general problem of the nature of the residual stress which is produced in metals by plastic elongation. A particular stress distribution will be suggested which accounts for the main X-ray diffraction observations which have been made. It will also be shown that certain magnetic measurements made on silicon steel can be understood in terms of this stress distribution. X-RAY OBSERVATIONS Uniform straining of a crystal lattice (macro-strain) causes a diffracted X-ray beam to shift its position, and nonuniform straining (microstrain) causes line broadening. If a bar of metal is plastically elongated in the longitudinal x direction and then unloaded, diffracted X-ray lines are observed to be both shifted and broadened.'-= Although the observed line shift indicates the presence of macro-strain, experiments have shown that no macrostrain, in the usual engineering sense of the term, exists.5"7 For example, removal of a layer from one surface of a stretched and unloaded bar does not produce curvature in the remainder of the bar 5'7 Fig. 1 shows the variation of lattice strain in the x direction, as determined from X-ray line shifts, with the applied stress in the same direction. The curve ABC is the normal stress-strain curve of the material, AB being the elastic portion and BC the plastic. In the elastic region AB, the strain measured by X-rays, called the lattice strain, and the strain measured mechanically are both proportional to the applied stress, and both return to zero when the applied stress is removed. Above the elastic limit the lattice strain would be expected to continue to increase along the line BD. Actually, it increases less rapidly with respect to stress, or even decreases, as shown by BE. If the applied stress is then decreased, the lattice strain decreases along EF, which is parallel to AB. As a result, there is a compressive residual lattice strain FA after unloading. STRESS DISTRIBUTION. Since a stretched and unloaded bar does not contain macrostress, it follows that the observed line shift must be due to a special distribution of mi-crostress. Such a distribution is shown in Fig. 2, which shows the variation of the stress u, across a stretched and unloaded bar. The material is assumed to consist of two kinds of regions: regions C, stressed more or less uniformly in compression, comprising the bulk of the volume of the material and responsible for the observed diffrac-

Jan 1, 1963

By E. L. Kinsella, F. S. White

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,' showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.' Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By F. S. White, E. L. Kinsella

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,' showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.' Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By J. B. Morgan

The mechanical behavior of MgCu2 from 20 o to 725°C has been determined by "brittle-ring" tensite-test techniques, axial compression, and bending experiments. Compressive ductility begins at 450°C (0.65 T/Tm) and slowly increases with increasing temperature white the tensile ductility is characterized by an abrupt brittle-ductile transition at 600°C (0.8T/Tm). The compressive strength increases eightfold from room temperature to 400°C with a "normal" decrease as the temperature is further increased. The tensile strength goes through a rather abrupt threefold increase above 600°C with a subsequent decrease at higher temperatures. The slip system is (111)[110] and the twinning system is (111)[112]. At high temperatures MgCu2 is quite rate-sensitive, and dynamic yield points are observed that are extremely orientation-dependent. The high-temperature creep behavior under constant load is characterized by an increasing strain-rate with time. The general characteristics of the mechanical behavior make it possible to classify MgCu2 with those materials in which initial mobile dislocation density and the dislocation velocity-stress dependence are significant in determining mechanical response. Mgcu2 is the C15 prototype of the cubic Laves phase. Its range of homogeneity extends from 32.8 to 35.5 at. pct Mg at 500°C and narrows at lower temperatures. The lattice parameter is reported to vary from 7.02 to 7.05A,1 and the compound is completely ordered to the melting point of 819°C. MgCu2 has a brassy metallic appearance, is extremely brittle, and many of its physical properties are intermediate between those of the constituent elements: the electrical resistivity is 3.5 x 10-6 ohm-cm, Young's modulus is 10x 106 psi, the shear modulus is 6 x l06 psi, and the thermal coefficient of expansion is 18.7 x 10-6 cm per cm per "C from 20" to 250°C. Usually, properties of intermetallic compounds as functions of temperature have been determined by hardness, compression, or impact behavior, and almost all of these experiments have been performed on polycrystalline materials. Tammann and Dahl,2 for instance, determined the onset of ductility in a series of binary intermetallics by ball-hardness measurements and found the onset to range between 0.71 and 0.96 T/T,. Lowrie's3 investigations included some tensile properties, and he found ductility beginning around 0.65 T/Tm for most materials examined. His work did include some data on polycrystalline, nonstoichiometric MgCu2, however. The present work is an attempt to extend the examination of the particular compound MgCu2 in single-crystal form in order to aid the formation of general concepts about mechanical be-

Jan 1, 1965

By Hsun Hu, R. S. Cline

A detailed studj) of texture formation in 2 pet Al-Fe single crystals with initial orientations of approximately (111) [112], (112) [111], and (112) [111] was made by examining the textures developed on the surface and at various interior sections of the crystal after rolling to various amounts. Depending' upon the initial orientation of the crystal, the surface and interior textures may differ only in sharpness, or may differ essentially in orientation. The orientation of the (111) [112] crystal does not change upon rolling up to 70 pet, but after rolling more than 90 pet a distinct component of (001) (110] orientation is developed. The texture formed in the two (112) (1111 type crystals consists of (111) (1121 and (001) (1101 components. The latter, however, is largely confined to the surface layers. The textures formed on both sides of the crystal are identical, and the texture composition profile is approximately symmetrical with respect to the central section of the strip thickness. The formation of these texture components is analyzed. DURING the past seven or eight years, deformation and recrystallization textures in rolled Si-Fe single crystals have been extensively studied by various investigators.1-7 From these studies, much knowledge on texture formation in bee crystals of various initial orientations was obtained. However, these results also raised many questions, regarding particularly the correlation between deformation and recrystallization textures, as well as the deformation texture itself of some particular crystals. To take a (111) [112] type crystal as an example, it was shown by Dunn and Koh2, 3 that this orientation does not change during deformation by rolling. This finding is consistent with the conclusion reached by Barrett and Leven-son8 with respect to iron crystals that (111) [112] is one of the stable end orientations. However, different recrystallization textures were observed by Dunn and Koh3 in (111) [112] type crystals of different initial thickness, which widened differently during rolling even though their deformation textures were identical. Another interesting example, also from the results of Dunn and Koh2'3 is that of texture formation in a (112) [111] crystal. This crystal developed a two-component deformation texture of (111) [112] plus (001) [110]. Its recrystallization texture, however, was found to be predominantly (110) [001], which is related to the (111) [112] component by a simple [110] rotation. This crystal, therefore, behaved as if the other deformation texture component, (001) [110], were not present. There are also discrepancies among the results of different investigators, as well as numerous unexplained fine features of the deformation texture of crystals of various initial orientations. In order to have a better understanding of all of these points, a detailed study of deformation textures is greatly needed. One of the obvious things that has been completely overlooked in previous texture studies is the possible effect of surface texture. All past work on the texture of Si-Fe single crystals was conducted in a rather simple manner, i.e., the rolled crystals were etched to a very thin sheet; then their textures were examined by transmission X-ray techniques. For recrystallization texture studies, unless precautions are taken by etching off a sufficient amount of the surface layer before annealing, the texture developed in the interior may be affected by the surface layer, which may well have a different initial texture and which may have undergone recrystallization earlier than the interior of the specimen. Because of this effect, it is now planned to reexamine the texture of various rolled and annealed single crystals at the surface, and at various sections below the surface by using reflection techniques. In some cases, both surfaces of the rolled crystal will be examined. In one of Dunn's early papers,9 he noted that at an early stage of rolling the crystal seems to divide roughly through the middle to become a sample which in effect consists of two layers having some what different orientations. This effect has never been further explored. The investigation described in the present paper constitutes the beginning of a series of thorough investigations of texture formation in deformed bee single crystals designed to clear up some of the uncertainties which have been discussed. We have chosen a high-purity 2 pet Al-Fe alloy for this investigation. It is known that the allotropic transformation of iron is eliminated by alloying with approximately 1petAl. Such an alloy, being very similar to silicon ferrite, can be heated to the solidus temperature without phase transformation. One reason for choosing A1-Fe instead of Si-Fe for the present investigation is that we have been able to make single crystals of a vacuum-melted high-purity A1-Fe alloy by the strain-anneal method without much difficulty, but were not successful in doing so with a vacuum-melted high-purity Si-Fe alloy. For many research purposes,

Jan 1, 1962

By Nicholas J. Grant, William H. Ferguson, Bill C. Giessen

Ta-lr alloys have been examined over the complete range of compositions using metallographic and X-ray techniques. The terminal solid-solubility limits, solidus temperatures, and intermediate phases were determined. There are four inter-mediate phases: o, tetragonal, analogous to a (Fe-Cr); 0,. orthorhombic; az, tetragonal; and a TaZr,, cubic, AuCu, structure. Of these, o and a, melt peritecticaLly, a, decomposes peritectoidally, and a TaIrs has a congruent melting point. Three peri-tectic and one eutectic reactions occur. 1 HE Ta-Ir phase diagram has not been treated in the literature. Intermetallic phases and terminal solid solubilities have been described and estimated.'-4 The previous findings have been confirmed in this work. A complete diagram with additional phases and solidus curves is presented. EXPERIMENTAL METHODS Starting materials were tantalum powder of 99.8 pct purity, supplied by the National Research Corp., Cambridge, Mass., and iridium powder of 99.9 pct purity, supplied by the Bishop Co., Malvern, Pa. Both powders were -200 mesh. Table I lists the analyses as given by the suppliers. A standard procedure was employed in making the alloy buttons, which was described in detail in Refs. 5 and 6, and which included repeated arc-melting of powder compacts and determination of the composition by the weight-balance method. This is especially justifiable due to the similar vapor pressures of tantalum and iridium. In the critical parts of the diagram, a spacing of 1/2 at. pct was used, based on premelted master alloy material. The observed structures and X-ray spectra were consistent with the composition sequence of the alloys. Table II lists the final alloy atomic percentages with the calculated percent error of composition. Cross sections representative in grain size and composition were selected for the study, as described in Ref. 5. Based on prior experience, no contamination from the tungsten electrode was considered. Temperature measurements were obtained using a Leeds and Northrup optical pyrometer and have been described extensively in Refs. 5 and 6. All heat treatments were made in the high-vacuum tantalum tube furnace mentioned in Ref. 5. Samples annealed in tantalum containers cooled from 1800" to 1000"~ in 5 sec; those annealed in ceramic crucibles cooled over the same range in 15 to 30 sec. The thermal treatments are listed in Table 111. All specimens were homogenized at 1735°C for 24 hr. Tantalum-rich compositions were treated in tantalum buckets. Iridium-rich compositions were annealed in tantalum buckets below the eutectic temperature of 1950°C; up to 2200°C, tungsten-lined tantalum baskets were used; and above 2200°C thoria crucibles were used. It was found that refractory oxides (in early stages of the investigation alumina crucibles were used up to 1800°C and thoria crucibles were used to 2400"~) give off minute amounts of oxygen and thereby influence the microstructure considerably, or react directly with the alloys.

Jan 1, 1963

By W. H. Class

The embrittling effects of oxygen, ozone, nitrogen, air, and surface residues, on NaCl has been investigated. The embrittlement by ozone and oxygen was found to be associated with the formation of a NaClO3 surface compound. In these cases the initial crack that was responsible for fracture (in a bend test) always nucleated at the corners between the tension and side faces. The behavior of air was very erratic and on certain days did not produce enzbrittlement. During these periods, crystals that had become embrittled by the ozone treatment completely recovered their ductility after a short exposure to the ambient atmosphere, It was established many years ago1 that considerable ductility could be obtained in NaCl single-crystal specimens if the crystal surfaces were dissolved in water either during or immediately prior to the test. The original interpretation of this effect by Joffe attributed the enhanced ductility to the removal of surface microcracks by dissolution. Later investigations2'3 have suggested that the exclusion of air from the specimen surface is the criterion for extensive plastic flow prior to fracture. The air em-brittlement in this later work was attributed to the diffusion of gaseous atoms into the surface layers of the crystal, thereby impeding the movement of dislocations. This model satisfactorily accounts for the reembrittlement observed after further air exposure subsequent to the water dissolution treatment. However, the situation has recently become more complex by the observations in several laboratories4-t that under certain conditions air exposure does not impair the ductility of NaC1. It has also been recognized5 that improper drying operations after water dissolution can leave surface precipitates that lead to embrittlement. Cleavage defects on as-cleaved crystals can often be another source of embrittlement. In the present work the effect of the gaseous atmospheres nitrogen, argon, air, oxygen, and ozone, on the ductility of rock salt was studied extensively. The embrittlement resulting from oxygen and ozone exposures was found to be associated with the formation of a NaC1O3 surface film. It is suggested that certain atmospheres, one of which often can be ambient air, which inhibit the formation or favor the decomposition of this compound, can promote ductility. Thus one aspect of the Joffe effect is certainly related to the removal of surface compounds or complexes by water dissolution. The effect of surface precipitates that remain after drying operations and of cleavage defects were also studied. In neither of the latter cases was the embrittlement as severe as that found with a NaClO3 surface layer. PROCEDURE AND SPECIMEN PREPARATION The nature of the embrittlement produced by the agents mentioned above was studied by means of microscopy, mechanical testing, and X-ray diffraction. Specimens were cleaved from large crystals of optical quality sodium chloride obtained from the Harshaw Chemical Co., and, except for those tested in the as-cleaved condition, were given a 15- to 20-sec immersion in distilled water followed by a rinse in absolute methyl alcohol. The specimens were then blotted on a soft, absorbent paper, and dried by a few seconds exposure to a stream of warm, dry air. Such a procedure was found to give a control surface which was microscopically free of residues. (A few crystals were intentionally painted with a concentrated NaCl solution in order to investigate the effect of surface residues). All specimens were of 0.140 sq in. cross-section. Crystals prepared in the above manner were immediately placed in a gas train where they could be exposed to the desired gases for preselected periods of time. For the oxygen and nitrogen exposures, pure reagent-grade gases were employed. The ozone was provided in the form of an ozone-oxygen mixture (approximately 10 pct ozone) prepared by passing commercial grade oxygen over a strong ultraviolet light source. All gases were dried prior to their introduction into the train. Since argon was found to be completely inert in its behavior (i.e., residue-free specimens that were exposed to argon were not embrittled), it was periodically utilized to check the control specimen surfaces as well as the condition of the gas train used for aging the specimens. After exposure to the gaseous media in question, the crystals to be used for the measurement of the strain to fracture were transferred from the gas train to a protective oil bath (without further exposure to the atmosphere) where the tests were conducted in three-point bending. The apparatus was so adjusted that the load could be applied at a constant, continuous rate. Other Snecimens from the gas train were deformed

Jan 1, 1962

By H. A. Bright, H. C. Vacher, J. G. Thompson

The methods employed for the determination of oxides and oxygen in ferrous materials may be roughly classed in two groups, "wet" methods and "hot" methods, the first group including the iodine, electrolytic, mercuric chloride, hydrochloric acid, nitric acid, and chlorine methods; the second group including the vacuum-fusion and hydrogen-reduction methods. The wet methods depend upon preferential solubility in a selected medium to separate the metallic portion of the sample from the oxygen-containing constituents. Subsequent analysis of the insoluble residue permits the isolation and separate determination of individual oxides and compounds. The hot methods depend upon the reduction of the oxide constituents of the sample by means of carbon or hydrogen at elevated temperatures. With the exception of the recently developed fractional vacuum-fusion method, the hot methods do not identify individual oxides and compounds but yield only a single value representing the sum of the oxygen contents of several or all of the oxide constituents present. With such diversity in the principles and aims of the different groups, it is not surprising that concordance of results by different methods has usually been difficult to obtain. The present cooperative attempt to define more rigorously than has been possible heretofore the accuracy and limits of usefulness of the various methods, originated in correspondence between Dr. John Johnston, Director of Research of the United States Steel Corporation, and other interested metallurgists. The plan was, briefly, to submit identical samples to a number of laboratories for analysis by different methods and to collate the results of these analyses. The project was endorsed by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers at the annual meeting in February, 1933, and has been conducted under the joint sponsorship of the Iron and Steel Division and the National Bureau of Standards. The latter organization undertook

Jan 1, 1937