Search Documents

By Kenneth K. Humphreys, Joseph W. Leonard, Robert L. Llewellyn, William C. McCulloch

INTRODUCTION The particular field of application of machines utilizing air currents as the primary separating medium is in the cleaning of the fine sizes of bituminous coal. Approximately 25,400,000 tons of bituminous coal were cleaned by air machines during 1965. They have not found any application for cleaning anthracite. Since the development and introduction of the first successful commercial pneumatic oscillating machine for cleaning bituminous coal in 19 16, by the Sutton, Steele and Steele Co, Dallas, Texas, and the American Coal Cleaning Corporation, formerly of Welch, W. Va., seven other successful pneumatic coal-cleaning machines have been developed and introduced to the American coal-mining industry: 1. Peale Davis: "Pneumo-Gravity" machine. 2. Arms "Concentrator," oscillating table. 3. Hey1 and Patterson oscillating table. 4. "Stump Air-Flow," pulsating air jig. 5. "Super Airflow," pulsating air jig. 6. Ridge air jig. 7. Phillip air jig. While not all coals can be beneficiated by air washing, the air washing of coals that are easy to clean can be readily proved advantageous. Of all the preparation methods, pneumatic cleaning is the most acceptable from the standpoint of delivered Btu cost. This is based on the premise that a percent of moisture is just as detrimental as a percent of ash. The principle of dry concentration has never been determined with scientific accuracy. To the present time the study has been more of an art than a science. It is possible to forecast the results of wet concentration from a study of the washability characteristics of the raw coal but only after applying rule-of-thumb methods of interpretation to the specific gravity and size distribution can it be ascertained that the raw coal is amenable to dry concentration. Air as a separating medium dates back to biblical times as exemplified in the winnowing of chaff from the grain. However, the same application of air to coal serves merely to blow the dust away and size the remaining particles. Pulsating air was the solution to the problem and largely eliminated the necessity for close screen sizing which was required on early separators. Because of the low density of air, a medium of sufficient density has to be built with the material itself. Hence there must be some device to impart to the bed the necessary mobility for proper classification. Also, the

Jan 1, 1968

By W. A. Eardley

FIFTEEN years ago the world's deepest oil well penetrated the earth about 7300 ft. That depth has now been more than doubled. Why has such deep drilling become necessary and how has it become possible? Three factors have had an important bearing: (1) Depletion of shallow zones, making it necessary to search for deeper producing measures. (2) The perfection of prospecting methods, which have been success- fully used to locate favorable buried structures, many at great depth. (3) Improvement in the quality of steels used for drilling.

Jan 1, 1940

By W. A. Backofen, A. T. English

The kinetics of re crystallization were determined metallographically for a 3-1/4 pcl Si-Fe rapidly compressed at temperatures of 710° to 911°C, and held for various times at the working temperature. As in re crystallization following cold wwk, the time for re crystallization was reduced by increased temperature and strain. Nucleation occurred chiefly at grain edges, although other pre-existing interfaces, notably inclusions, also served as nucleation sites. The importance of intragranular nucleation to grain refinement in hot working is pointed out, together with some possible techniques by which nucleation might be induced within the grains. The observed isothermal growth rates are quite accurately described by the equation G = 4 x 10-'/t (cm per sec), independent of temperature and strain at all but the shortest times. Changes in G during recrystalliza-tion can exceed two orders of magnitude. It is argued that release of stored energy associated with lattice defects cannot adequately explain the time dependence. A suggested alternative involves processes of solute segregation and desegregation in the unrecrystallized matrix and at the moving boundary, respectively. EFFORTS to improve hot-working practice are hampered by an incomplete understanding of the fundamental metallurgy involved. Research directed at establishing the required basic foundation falls into two categories, the first concerned with measurement of mechanical properties under the conditions of high temperature and strain rate which characterize such processing, the second focused on structure and its relation to the deformation conditions. Rossard,' Rossard and Blain,2 and Hardwick and Tegart have conducted many high-speed, high-temperature torsion tests on various metals. One of their objectives was interpretation of stress-strain curves in terms of the structures of specimens rapidly quenched following interruption of twisting. They showed that appreciable hardening occurred in the early part of the test, and that this hardening reflected the concurrent development of an increasingly dense substructure within the grains. The detailed nature of this substructure was observed to depend on the ease of polygonization which, at least in fcc metals, varies with the stacking-fault energy.= By holding specimens after interruption but before quenching, the nucleation and growth of new grains could also be studied. Some success has been realized in relating the microstructure of hot-rolled steel to its temperature:strain rate:strain history with such testing.' The same general observations have been made by others investigating rolling4f5 and drop-hammer forging.~-~ Incident to these experiments, some efforts were made to determine the kinetics of re-crystallization as well as the velocity of the migrating boundaries. The results have been largely qualitative, owing to difficulties of interpreting hardness measurements5 and microstructures. The work described here was undertaken to obtain more quantitative information from tests on a material having suitable metallographic properties, and, in this way, to provide further insight into the fundamentals of this practically most important kind of deformation processing. I) MATERIALS AND EXPERIMENTAL TECHNIQUES Materials. Electrolytic etching of a Si-Fe alloy reveals dislocations and substructure in unrecrystallized grains.8'9 This unique characteristic makes possible a precise determination of the extent of recrystallization. For that reason, it was the material selected for all experiments in the present work. The two particular alloys that were used are identified in Table I. A major difference between "A" and "B" is the number of inclusions, as noted in the table. Most of the experiments were made with material "A". It was received as hot-rolled plate 1 in. thick, sawed to 2-in. widths, hot-forged at 1200°C to 5/8-in. rounds, and finally annealed in a mechanical vacuum at 1000°C for 24 hr. The result was substructure-free grains of mean diameter 0.05 cm.*

Jan 1, 1964

By AIME AIME

LIFE will not be difficult for those who attend the fall meeting of the Petroleum Division at the Conoco Club, Ponca City, Okla., Sept. 30-Oct. 1. An attractive program to appeal to oil company executives and lawyers, as well as technologists, has been arranged and the Continental Oil Co. has contributed for the occasion the buildings, grounds and facilities of the club. E. 0. Bennett, Continental Oil Co., Ponca City, is chairman of the arrangements committee, and reservations for rooms and trips, requests for information, etc., should be sent to him.

Jan 1, 1932

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

Established as a Division January 15, 1932 John C Calhoun, Jr, Chairman O Cutler Shepard, Vice-Chairman J R Van Pelt, Jr , Past Chairman Thomas A Read, Secretary-Treasurer Dept of Mining and Metallurgical Engrg University of Illinois Urbana, Illinois

Jan 1, 1956

By Sadtler, C. B.

IT is generally assumed that in most metals and alloys a given tensile stress produces a given deformation irrespective of the length of time during which the stress is applied. This assumption is justified in most of the important engineering applications of metallic materials; however, in the case of some metals and alloys used or tested at temperatures over or slightly under that at which recrystallization can occur the assumption is not warranted.1 This paper deals with the variations of deformation produced by a constant tensile stress acting for varied lengths of time in the special case of thin aluminum alloy sheet of the duralumin type, which had been subjected to different thermal and mechanical treatments. The material investigated was in the form of a sheet approximately 0.002 in. thick, which had been cold-rolled from a thickness of 0.020 in. It has been found that at a sufficiently high constant tension such material deforms continuously with the elapse of time and that the rate at which this deformation occurs is greatly influenced by the previous thermal and mechanical treatments.

Jan 1, 1927

By R. W. Gurry

In a series of charts this paper presents the composition of all gas mixtures, composed of the elements carbon, hydrogen, oxygen and nitrogen, which at temperatures from 1000° to 1800°F are in equilibrium with (1) austenite of various carbon contents, (2) iron and iron carbide, (3) graphite, (4) iron and its oxide. THIS paper presents the results of calculations made to determine the proportions of CO, CO2, CH4, H2, H2O and N2 in gas mixtures which, at temperatures from 1000" to 1800°F, satisfy, individually, the following conditions: (1) equilibrium with carbon steel of specified carbon content throughout the stable 7 iron region; (2) equilibrium with iron and iron carbide, both above and below the eutectoid temperature; (3) equilibrium with graphite; (4) equilibrium with iron and its oxide. From these data a new type of chart has been prepared which permits one to determine, from a room-temperature analysis of the furnace gas in question, the effect of the gas upon the steel at furnace temperature. Thus a guide is provided as to the carbon content which will result and as to the possibility of oxidation or sooting. All of the atmospheres commonly used in the commercial heat treatment of steel are composed of some or all of the simple constituents CO, CO2, CH4, H2, H2O and N2, and also in some cases oxygen or higher hydrocarbons. As the gas mixture is heated certain alterations in the proportions of the constituents take place, and at the temperature of the furnace the composition is, in general, not at all that of the entering gas. If equilibrium in the gas phase is presumed a calculation involving the use of certain fundamental data predicts for a certain temperature the carburizing, decarburizing, or sooting characteristics of a given atmosphere, and, upon the additional assumption of equilibrium between gas and metal, also the oxidizing ability of the gas and the ultimate carbon content of the steel. The extent to which these predictions are fulfilled will depend upon how closely the assumptions of equilibrium are realized in any particular case. Although at lower temperatures equilibrium is often not reached, there is considerable evidence indicating that above about 1000°F the approach to equilibrium in the gas phase is generally substantially complete, particularly in the vicinity of the steel which acts as a powerful catalyst in promoting reactions in the gas phase. The extent of the gas-metal reactions is commonly affected essentially by the sojourn at temperature; equilibrium with respect to carbon, for example, is accomplished simply by continuing the treatment long enough. However close the approximation of equilibrium may be in any instance, the above mentioned calculation indicates the condition of the steel at equilibrium, and at the present time this is the only basis of control of a furnace atmosphere. The effect at elevated temperature of a gas of a certain composition at room temperature upon a given steel has customarily been judged by first calculating from gas equilibrium constants the proportions of the gas constituents at the temperature of the steel, then comparing certain of these with the proportions known to be in carbon or oxygen equilibrium. This process is tedious and time-consuming, in particular because the calculation generally involves a series of successive approximations; and since some knowledge and familiarity with this type of computation are required, not everyone needing the information has been, in the past, in a position to obtain it. By making a series of equilibrium calculations, combining with fundamental data for gas-metal reactions, and plotting the results in a special way, a chart has been prepared which enables anyone

Jan 1, 1951

By William Rawles

THIS report is the first of a series planned by The Mineral Inquiry, organized by the American Institute of Mining and Metallurgical Engineers to make factual studies of the world's mineral resources in their political and international relations. The efforts of The Inquiry are directed toward filling certain notable gaps in available information, without duplication of many other investigations touching this field which" are being conducted by other organizations, public and private. Much of its work is indirect-suggesting topics for study by other individuals and organizations and aiding in their planning and correlation. The present report is designed to show the nationality of the commercial control of mineral resources, in addition to the geographic distribution of production by nation-in other words, the overlapping of political and commercial control. Detailed accuracy cannot be claimed for the figures presented. For some companies division of ownership by nationality has been very difficult to ascertain, as many companies are reluctant to dis-close the extent of their holdings in other corporations, and the impossi-bility of tracing all stock ownership is obvious. Also there are frequent changes in the distribution of stock control. The percentages given rep-resent only the participation that has been identified definitely, even though it is known in some cases with fair certainty that larger interests exist, as, for instance, American participation in foreign chromite companies. In bringing' together these figures we have had the cordial co-operation of the United States Bureau of Mines, the United States Geologi-cal Survey, the Mineral Division of the Bureau of Foreign and Domestic Commerce, the Brookings Institution, and of many specialists connected with the mineral industries covered. The report does not cover the entire list of minerals. Coal, although it is one of the most important minerals, was omitted because not more. than one or two per cent of the world's production comes from mines that are owned by companies foreign to the countries where the coal is produced. Others, such as gold, are omitted because sufficient data have not yet been accumulated. It is hoped that some of these may be covered in subsequent reports. It is not our purpose here to discuss the significance of the figures sub-mitted, but only to point out the general nature of the problems on which they have a bearing.

Jan 1, 1933

By O. C. Wheeler

In order that the series of reports on oil and gas in Colombia may be complete, the report for the year 1941, which was not available for Volume 160 of the TRANSACTIONS, is given here. The report for 1945 begins on page 4o6.

Jan 1, 1946

By John Brownson

Ge-Si N-N heterodiodes hare been built recently which show promise as high-speed logic devices. Low-resistivity germanium is deposited on silicon substrates held at temperatures above the germanium melting point and an alloyed heterojunction formed. The diodes are fabricated from this material using conventional mesa techniques. Over-all device qualify has been greatly improved by the use of epitaxial silicon substrates, that is, a subsirale consisting of a film of thin, high -resistivity silicon on a thicker Piece of low-resistirily silicon crystal. A semimpirical device design equation has been devised which predicts switching performance fairly well within the range of resistivitics and geometries employed. Switching times 01 0.9 ns and PIV 's of —20 v are typical of the better 10-ma diodes. Switching times as low as 0.5 ns have been observed for 10-ma diodes and as low as 2.8 ns for 200-ma diodes. With further development it should be possible to improve switching speed by a factor of four. IN our laboratory, Ge-Si heterodiodes have been built recently which show promise as high-speed logic devices. The diodes have been built using a process reported in some detail in an earlier publication.' The process in short involves alloying a thin film of low-resistivity germanium into a silicon substrate. the germanium having been transported and deposited by the well-known Theuerer halide reduction process.2 This process contrasts with that reported earlier by Oldham who used an essentially conventional direct epitaxial deposition technique.3 Oldham's process, unlike ours, requires cleavage of the silicon sample inside the reactor furnace the instant prior to deposition. Our process has the advantage of yielding large-area macro-scopically plane heterojunctions. Heterodiodes in general have several interesting properties. Without attempting to summarize the theory of heterojunctions.4 two of these properties which have direct relevance should be mentioned. First, N-.V and P-P heterojunction diodes rectify alternating current. Provided that either the band gap or the electron affinity of the two materials is different (which in general is the case), electronic barriers will exist in the junction band structure. When the device is sufficiently forward-biased, the barriers shift so as to permit current flow, and when it is reverse-biased. the barriers block current flow. Second, for N-N and P-P heterodiodes. the foward-conduction process involves majority carriers only. Consequently. when such a device is turned off. there is no minority-carrier storage and hence the diodes switch on and off quite rapidly. As we have reported earlier. N-P and N-N Ge-Si heterodiodes have been built in this laboratory. As one would predict from theory, the N-P heterodiodes were rather slow in turning off while the N-N's were quite fast. Similarly, the turn-off time of the N-P's increased rapidly with forward current while that of the N-N's was independent of forward current. Both N-N's and N-P's were moderately photosensitive. Photocurrents resulting from normal room illumination were as high as 1 µa at 1 v for small-area devices. The most disappointing parameter of the early N-N devices was reverse leakage.' The reverse characteristic was invariably "soft" and leakage at only several volts reverse bias was intolerable. The reverse characteristic was greatly improved by using higher-resistivity silicon substrates. Leakage becomes large at voltages about one third of the avalanche voltage one would expect of a P-N homo-junction formed on silicon of the same resistivity. Thus leakage could be reduced to reasonable limits by using unconventionally high-resistivity silicon. Medium-power diodes formed on 30 ohm-cm substrates leaked typically 15 to 50 µa at 100 v reverse bias. The use of high-resistivity silicon substrate material, however, created a new problem. In order to have an acceptable forward-conductance characteristic. the area of the diodes had to be increased. With this increase in area, the capacitance increased. Switching time for N-N heterodiodes is essentially a linear function of capacitance. Thus when the resistivity was raised. so was the switching time. A SEMIEMPIRICAL HETERODIODE DESIGN EQUATION As a result of our experiments with a limited range of diode geometries and resistivities. a semi-

Jan 1, 1965

By J. F. Shirley, H. K. Burke

In January, 1964, three years of laboratory and pilot plant test work reached its culmination. The San Manuel Div. of the Magma Copper Co. switched its molybdenite extraction circuit from the sodium hypochlorite-ferrocyanide process to the new process described in this paper. The San Manuel Div. Concentrator of the Magma Copper Co. is located near San Manuel, Ariz., approximately 45 miles northeast of Tucson. The concentrator treats approximately 35,000 tons of ore per day containing about 0.85% copper and 0.025% molybdenite. The San Manuel ore body is a disseminated copper deposit in quartz monzonite and quartz monzonite porphyry. The primary copper mineral is chalcopyrite; minor amounts of chalcocite, bornite and covellite are also present in varying degrees. Pyrite makes up somewhat more than half the sulfide content of the rock. The molybdenite is nearly always found on fracture faces or associated with quartz veinlets.' On January 9, 1964, the sodium hypochlorite-ferrocyanide process that had been used for molybdenite recovery was replaced by the following process: 1) A conditioning step with hydrogen peroxide, sulfuric acid, sodium cyanide and zinc sulfate. 2) A two stage rougher flotation step with stove oil and sodium ferrocyanide. 3) One cleaning step with sodium ferrocyanide. 4) One cleaning step with sodium hypochlorite and potassium ferricyanide. 5) Four cleaning steps with an anti-foam Exfoam 636 and potassium ferricyanide. COPPER CONCENTRATOR Since molybdenite recovery is closely allied with previous steps in the operation, the copper concentrator will be briefly described first. The ore is ground to approximately 5% plus 65-mesh and 65% minus 200-mesh in a two-step grinding circuit consisting of rod mills in open circuit and ball mills in closed circuit with rake classifiers. A straight forward rougher circuit producing only one concentrate is used. The rougher concentrate is combined with the discharge from the regrind ball mills and is then cycloned, with the overflow going directly to the cleaner circuit and the underflow going to the regrind mills. The feed to the cleaner circuit is approximately 90% to 94% minus 325 mesh. The cleaner circuit consists of two stages in which the tailing from the final cleaner stage is returned to the primary cleaner and the primary cleaner tailing is returned to the rod mill discharge at the head of the circuit. Approximately 0.013 lb of the allyl ester of amyl xanthate (S-3302) per ton of ore is added to the rod mills and approximately 0.006 lb of sodium isopropyl xanthate (2-11) per ton of ore is stage added down the rougher banks. The frother used is methyl iso-butyl carbinol (MIBC) and it is added at various points in the grinding and the rougher flotation circuits. Lime is added to the ball mills and/or to the rod mills to maintain the desired pH in the rougher flotation. The rougher flotation has been operated at various pH levels between 10.5 and 11.5. Fuel oil is added in the regrind mills at a loading of approximately 0.01 lb per ton of ore. Factors Which Directly Affect Molybdenite Recovery: It has been found at San Manuel that, to obtain maximum molybdenite recovery, an oily type flotation collector must be added in the grinding circuit. When molybdenite is crystallized in the characteristic platy form, which appears to be the case almost all of the time at San Manuel, its surface has a greater tendency to adhere to oils than water. 2 Of the several oily type collectors available on the market, the allyl ester of amyl xanthate seems to be the best molybdenite promoter. The floatability of San Manuel's molybdenite does not appear to be affected, at least up to a pH of 11.5, by lime. It has been reported that at several plant operations high lime alkaline circuits have adversely affected the molybdenite recovery.3,4 It has been found through microscopic studies that the bulk of the chalcopyrite will float before the molybdenite in both the rougher and cleaner circuits. It is necessary to add fuel oil to the regrind mills to enhance the

Jan 1, 1965

By J. L. Wyatt

THE smelting of ilmenite to produce a slag rich in titanium, with pig-iron as a byproduct, introduces new concepts in electric smelting metallurgy. Titanium slags are characterized by low electrical resistance, thereby requiring a different type of electric furnace operation, and power supply sources substantially different from those encountered in normal steel melting and siliceous ore smelting furnaces. This paper describes special apparatus for determining specific electrical resistivity of titanium slags, and reports the values obtained on slags encountered in the process of smelting ilmenite ores. In an induction furnace under conditions approximating normal furnacing operation, 25 general heats and 6 special standardization and comparison heats were run. Results indicate relatively low resistivity. Resistivity depends primarily on slag composition, and, to a lesser degree, on temperature. During the summer of 1947 a cooperative project between the National Lead Co. and the Bureau of Mines was conducted at Boulder City, Nevada, in the Electrometallurgical Laboratories of the Bureau. The project involved smelting of ilmenite ores in electric furnaces, and has been reported in detail.' The author participated as a member of the staff of the National Lead Co. during the entire campaign. One outstanding characteristic of the titaniferous slags, their apparently excellent and variable electrical conductivity, was considered sufficiently important to warrant further study. Although little electric smelting of iron ores has been done in the United States, a certain amount of information is available for comparative purposes. Personal experience in smelting siliceous iron ores in electric furnaces furnished further information for comparison. In general, silicate slags are relatively poor conductors of electricity. Current flow during smelting operations may be maintained through a floating layer of coke on top of the slag bath, or through a bath of molten iron, beneath the slag. Silicate slags are not sufficiently conductive to furnish a path for current passage when normal furnace voltages are used. Experimental smelting of a silicate iron ore was undertaken for comparative purposes. A fluid melt was not obtained until the FeO content was reduced to 15 pct. The resistivity increased as the FeO content decreased, FeO compounds being the most conductive of the various oxides in such a normal slag system. The converse appears to be true in slags containing large percentages of TiO2. It has been found that titanium slags become molten with FeO percentages in excess of 30 pct, and that the conductivity becomes generally better as the FeO con-tent of the slag diminishes. This phenomenon was demonstrated in the furnacing operations at Boulder City. During the initial smelting period furnace electrodes could be held immersed several inches in the slag, with tap selectors set for a no-load voltage of 70 v. As the FeO content decreased, the furnace electrodes would "walk up," until at one point in the process the tips would break the surface and arc on top of the slag. This was undesirable since direct arcing caused losses of important flux additions. The slag compositions under study at that time were such that losses due to surface arcing sometimes caused viscous slags to be formed. Forcing the electrodes into the slag bath by manual control to prevent surface arcing resulted in excessive power input and lack of control. Suitable low voltages were not available. Measurement of the electrical resistivity of titanium slags at various operating temperatures and slag compositions was undertaken. It was believed that this information would be of use in the design of electric furnaces suitable for smelting ilmenite, with voltages, electrode sizes, and electrode spacing adapted specifically to titanium slags.

Jan 1, 1951

By H. H. Hausner, H. S. Kalish

IN recent years zirconium and beryllium have become of great interest because of their special properties. Zirconium is known for its remarkable ability to absorb the gases oxygen, nitrogen and hydrogen, has extensive use as a getter in electron tubes and has indeed become the primary metal in the manufacture of photoflash bulbs. Beryllium is of interest because it is light metal and as such could supplement aluminum and magnesium in light metal applications. The late development of zirconium ductile at room temperature produced by both the iodide and calcium reduction methods has stimulated frequent articles on this metal in the recent literature. Beryllium is so closely akin to zirconium crystall-ographically that some investigators are of the opinion that beryllium should be ductile at room temperature if it were pure enough. The crystallographic relationship of beryllium and zirconium, the interest created in Be-Zr alloys where the zirconium is believed to function as a remover of solid solution gas in beryllium and thus increase the ductility of the beryllium rich alloy, and the amenability of these metals to powder metallurgy methods stimulated this approach to an investigation of the system Be-Zr. Preliminary work showed that a zirconium compact melted when pressed in contact with a beryllium compact and sintered at 1250°C, without any apparent final bond between the two. A search of the literature revealed nothing pertinent about the Zr-Be system or about any zirconium - beryllium alloys. In 1936 Misch³ vaguely identified the compound ZrBe2 and reported that it has a deformed cubic structure. Two patents," , were issued to Mach-lett Laboratories in 1943 and in 1946 regarding the addition of small amounts of zirconium to beryllium in order to improve the ductility of beryllium so that it may better be used for X ray windows. In considering the alloy formation of beryllium with other metals Raynor thought it unlikely that zirconium would have any solid solubility in beryllium. From this indefinite information nothing could be ascertained about the possible use of Zr-Be alloys or the use of these metals intimately. A brief preliminary study of the system Zr-Be by powder metallurgy methods was undertaken to provide regions for more intense studies of Zr-Be alloys and as a guide to a formal phase diagram determination. The investigation described in the following pages was completed in less than three weeks. The usefulness of this rapid method to facilitate phase diagram studies and new alloy investigations will be shown. Materials and Procedure Zirconium powder was produced from crystal bar stock of high purity supplied by Foote Mineral Co. The crystal bar was converted to hydride at 730°C, crushed, and the hydride decomposed in purified argon at 850°C. 60 pct of the powder passed through a 325 mesh screen, 40 pct of the powder was —140 mesh, +325 mesh and the average particle size of the total was 8 to 12 microns. The beryllium powder was used as re-

Jan 1, 1951

By Paul R. Dingess, Edward H. Hare, Douglas C. Brockie

Mining in the Tri-State district of Missouri, Kansas, and Oklahoma has been nearly continuous from about 1848 until the present day, although the major activity was from about 1880 to 1955. The district, which has produced over $2 billion in zinc and lead concentrates, ranks as one of the greatest mining districts in the world. Unlike other Mississippi Valleytype deposits in the United States, which occur in Cambrian and Ordovician limestones and dolomites, the Tri-State district ores occur in Mississippian limestones containing abundant chert. Zinc is 5 to 6 times more abundant than lead. In the Picher Field, the principal sub-district which has accounted for 61 percent of the total district production, most of the ore has been mined from the single horizon, M bed. Most ore bodies, other than those of the "Sheet Ground" or blanket-type, are in large, essentially flat-lying breccia zones and have a definite mineral zonal pattern. An irregular, generally elongated central dolomitic core is surrounded progressively outward by the main ore run, the jasperoid zone, the muddy or shaly and bouldery zone, the sparry calcite limestone zone, and the fossiliferous, dominantly crinoidal, limestone zone. Some of the zones may be absent or nearly so and may overlap to some extent with an adjacent zone. Although the district has been studied by many authors, much controversy still exists about such items as genesis, paragenesis, and time of emplacement. These subjects are discussed in the paper.

Jan 1, 1968

By E. S. Machlin, Morris Cohen

The isothermal formation of martensite in a 71 pct Fe, 29 pct Ni alloy is found to take place mainly by the nucleation of new plates rather than by the growth of existing ones, and is dependent on the temperature and time of the isothermal hold, the amount of atherrnal martensite present, the state of internal strain, and the application of tensile stress. The conclusion is reached that the isothermal nucleation is activated by thermal fluctuations superimposed on localized regions of very high strain. The reaction-path concept, involving martensite nucleation at strain embryos by athermal activation on cooling, or by thermal fluctuations on holding, reconciles the athermal and isothermal modes of transformation, and offers a unified picture of the kinetics of martensite formation. THE phenomenon of isothermal martensite formation has been the subject of considerable study lately,'-' and its reality has been thoroughly established. The existence of such isothermal transformation has been claimed to confirm the nucleation and growth hypothesis as applied to the martensitic reaction.1 " However, the isothermal formation of a martensitic phase is also compatible with the reaction-pathw escription of the transformation. The purpose of this investigation is to examine the isothermal mode of the martensitic reaction, both theoretically and experimentally, in order to test the likelihood of the above two mechanisms. Material and Methods The alloy used in this study contained about 71 pct Fe and 29 pct Ni. The complete analysis was 29.5 ± 0.2 pct Ni, 0.036 pct C, 0.02 pct N, 0.19 pct Mn, 0.09 pct Si, 0.008 pct P, and 0.006 pct S. The amount of isothermal transformation was determined by electrical resistance measurements using a Kelvin double bridge. The specimens were in the form of rods 1/16 in. diam x 4 in. long. Aus-tenitizing was performed at 1095°C for % hr either in a pre-purified nitrogen atmosphere or in an evacuated Vycor tube, followed by oil quenching to room temperature. After this treatment, the samples were completely austenitic, and the transformation studies were conducted at subatmospheric tempera- tures. Lineal analysis and X-ray determinations of retained austenite were used to calibrate the electrical resistance changes in terms of the percentage of martensite. The martensite range curve for this alloy is given in Fig. 9 of ref. 6. The M, temperature occurs at about -18°C (255°K). Reaction-Path Theory The nucleation and growth description of the martensitic transformation that occurs isothermally has already been given by Kurdjumow.','2 However, no comparable treatment exists using the reaction-path concept." Consequently this section presents the reaction-path description of the isothermal mode of the martensitic transformation. According to the latter theory, there is a reaction path (a strain) which describes the relative motion of the atoms during their transference from the austenitic to the martensitic state. The possibility exists, therefore, that the nucleation of a martensitic plate is accomplished by an embryo that comprises a state intermediate between that of austenite and martensite. This state may be attained within a finite volume by means of a homogeneous strain of the austenitic matrix. There is a free-energy barrier (F.) along the reaction path, corresponding to a critical strain in a critical volume. When activation is achieved, a spontaneous increase in strain and volume of the embryo takes place to generate the full-size martensitic plate. This mode of nucleation is to be distinguished from the more conventional mode involving embryos of the martensitic phase that merely grow in size by an interface motion. There are two ways whereby embryos in the austenitic phase can achieve the critical state of strain for isothermal nucleation: 1—through the formation of internal strains by plastic deformation or by stress; and 2—through thermal fluctuations, preferably superimposed upon existing internal strains. The activation free energy F,, must be supplied either mechanically by internal strains or thermally by energy fluctuations, or by a combination of both.

Jan 1, 1953

Jan 1, 1931

Willet G. Miller, Toronto, Canada (communication to the Secretary): In his interesting paper Mr. Lindgren says: " As to ultimate results, it would seem as if we should be justified in concluding, with Prof. Suess, that the gold-supply of the world will gradually decrease if no further important improvements are made in the processes for the extraction of this metal; but regarding events so far distant no predictions may safely be made." It seems to the writer that no very important improvements require to be made in order at least to keep up the present production for many years to come. In many parts of the world there are large deposits of auriferous material which can be worked if present conditions are slightly changed. In the territory occupied by the Archean protaxis of the Province of

Jan 1, 1903

By A. T. Yu

As the first loads of Noamundi iron ore rumbled into the new 54-in. Gyratory Crusher on March 30, 1968, one of India's largest and most modern iron ore processing complexes began operations. The completion of the $13 million mining and processing complex brought to a successful conclusion the second chapter of a phased expansion program initiated in 1958 by India's gigantic Tata Iron and Steel Co. The completed complex will yield annually 2.5 million tons of washed, sized ore and sinter fines destined for Tata's furnaces at Jamshedpur. Hewitt-Robins Div. of Litton Industries was awarded the turnkey project on the basis of world- wide competitive bids. Eighty miles southwest of the city of Jamshedpur, Noamundi lies on an approximate geographic grid of 22º-5' latitude north and 85º-30' longitude east. The mine is approximately 600 ft above sea level.

Jan 11, 1968