Search Documents

By Ammar Henchiri, Godfrey McDonald

"Breakwater Tunisia S.A.’s Bougrine mine is located in a semi-arid region of Tunisia characterized with Triassic salt domes. Due to extensive agricultural land-use in the mine area, a zero-discharge tailings facility design and high water recycling rates to the concentrator were chosen to minimize the environmental impact to the surrounding area. The process water supply has an accumulation of naturally occurring salts due to high evaporation rates and the need to recycle 70% of the process water. The elevated salt content of the process water had an adverse effect on the efficiency of the flotation reagents, which led to the production of lower quality zinc concentrate.The impact of the water salinity on the zinc concentrate quality was documented by extensive laboratory testing. A feasibility study was prepared and a decision was made to install a reverse osmosis plant for desalination of the process water. A plant was constructed during 2000 which currently supplies up to 85 m3/hr of de-mineralized water, equal to approximately 45% of the total process water requirement. The salinity of the process water decreased from about ten to twelve grams per litre before installation to less than three grams per litre. Together with minor modifications to the concentrator circuit, Breakwater Tunisia has increased the zinc concentrate grade from 50% zinc to 55% zinc without compromising the zinc recovery rate of approximately 84%.This paper discusses the successful installation of a reverse osmosis desalination plant that allowed Breakwater Tunisia to improve the grade of the Bougrine mine zinc concentrate and thus increase the net smelter return.INTRODUCTIONBreakwater Resources Ltd., through a wholly owned subsidiary, Breakwater Tunisia S.A., acquired the Bougrine underground mine and related assets in September 1997. During the winter of 1997/1998, the company rehabilitated the mining equipment, modified the concentrator circuit, developed a new mine ventilation system and prepared a new mining production program. The mine was reopened on May 2, 1998 and was in commercial production as of June 1, 1998."

Jan 1, 2003

By X. S. Tan

This paper deals with the analysis of stress condition on the interface between two types of floor rock materials when the vertical stress is larger, or when the horizontal stress is larger in a rectangular opening. It indicates that the floor Failure and the failure stress of floor rocks are closely related. It also demonstrates that a larger horizontal stress is one of the most important factors in increasing the potential for floor rock failure and floor heave.

Jan 1, 1990

By Paul R. Smith

The Colorado School of Mines Research Institute (CSMRI) was founded in 1949 to fill mining industry and government needs for minerals research and development. The operations of scores of mines, mills, and plants around the world are based on the results of work done by the Research Institute. Among other things, the Research Institute conducts studies in geology, mine planning, mineralogy, size reduction, minerals processing, and hydrometallurgical techniques in extractive metallurgy. Many CSMRI projects also involve energy and environmental considerations. What follows is a summary of some of the studies in which the Research Institute has been and is currently involved, as well as some comments on trends and developments in the industry.

Jan 2, 1982

By AMIR EHSAN KIANFAR, Moritz Ziegler, TOBIAS HARTMANN, ELISABETH CLAUSEN

Accurate positioning information is a central step in the process of increasing automation and digitalization in the mining industry. Underground mine environments are prime examples for GNSS-denied environments that pose several additional challenges for the employed indoor positioning system (IPS). This work presents an ultra-wideband (UWB)–based system specifically tailored for underground mine environments. Initially, the UWB technology is reviewed and basic concepts of IPS are explained. Both software and hardware are described in detail, including positioning algorithms, electrical circuitry, and the mining-compatible enclosure. Finally, the results from field tests in an underground mine are presented and positioning performance and the influence of dilution of precision (DOP) on positioning results are empirically evaluated. The results show that the localization errors are mostly below 1 m. Individual zones of high localization errors are suspected to be caused by noise interference. Significant DOP influence due to the mining drift geometry can be confirmed. The system shows promising localization results for different mining applications, while influences negatively impacting the accuracy are presented as items for future research.

Jul 7, 2023

By P. Somasundaran, D. W. Fuerstenau

This article presents the results of an analysis of grinding of 1:1 mixtures of 4x8-mesh quartz and limestone in laboratory ball and rod mills. From these experiments, the amount of energy consumed in grinding each component of the mixture was determined. In the ball mill, limestone consumes slightly more energy than quartz in the initial stages of grinding, but as the grinding proceeds quartz begins to consume a slightly greater fraction of the energy. The postulate that the fraction of energy consumed by any material in a ball mill is proportional to its volume fraction has been shown to be approximately true. On the other hand, in a rod mill energy consumption by quartz and limestone is equal only in the initial stages of grinding, with energy consumption by quartz greatly exceeding that by limestone as rod milling proceeds. Preferential energy consumption in tumbling mills has been discussed in a number of papers. For example, from an analysis of the kinetics of comminu- tion in ball mills, Arbiter and Bhrany' obtained rate equations based on the postulate that only coarse particles are ground, indicating that fine particles are protected from the action of the balls by coarser particles. In rod mills this protective action is much more pronounced than in ball mills. Recent studies on the rod milling of limestone-quartz mixtures have shown that this protective action causes the mineral with the lowest grindability (quartz in this instance) to consume the greater fraction of energy. 2 However, in the ball milling of mixtures it has been postulated that the consumption of energy by one of the constituents is determined by its volume fraction within the mill. 3 Possibly this hypothesis may be a simplification of the ball milling of mixtures since the protective action suggested by Arbiter and Bhrany may result in some preferential energy consumption by one of the constituents of a mixture. The objective of this study has been to determine preferential energy consumption in laboratory ball and rod mills by analyzing size distributions of each material in the products obtained from grinding 1:l mixtures of quartz and limestone. MATERIALS AND METHOD The procedure for carrying out the tests on wet grinding quartz-limestone mixtures has already been described.'r3 In the present investigation, 1:l mix-

Jan 1, 1963

By J. C. Thornley

Service failures of seemingly conventional galvanized bolts, in normal operation, on transmission towers in New Brunswick have been found to be the result of hydrogen cracking. In both these cases, similar failures elsewhere can be avoided by suitable clauses in the purchase specifications. In the first case described, the manufacturing procedure was responsible for strengthening and embrittling a standard, soft, constructional steel. In this case, a fracture mechanics analysis predicted critical crack depths for final fracture very similar to those found in practice. This case reveals an apparent cooperative connection between hydrogen embrittlement and strain ageing in plain carbon steels. In the second case described, the steel was simply a high strength steel which should not have been made into galvanized bolts.

Jan 1, 1979

By C. Jay Hodgson

Hydrothermal systems form on land where and when an impermeable cap-rock unit ( either natural or self-sealed) , a permeable aquifer. and permeable discharge and recharge channels (cross-stratal permeability) develop in an anomalously hot part of the crust. A consideration of the relationship between magmatic and tectonic events in volcanically active areas indicates these conditions arise during: (1) the resurgent doming stage of the resurgent caldera cycle; (2) following movement on the bounding faults of tilted fault blocks ; and (3) as a result of hydrothermal boring associated with the intrusion of major sills. On the assumption that the submarine hydrothermal systems which deposit volcanogenic massive sulphide ores are comparable to subaerial hydrothermal systems, it is suggested that: (1) the horizon of mineralization corresponds to the time period when conditions favour the development of hydrothermal systems, as outlined above; (2) exploration for Cu-rich Cu-Zn-Pb or Cu-Zn ores should be directed to paletopographically high areas near discharge conduits , whereas exploration for Cu-poor ZnPb ores should concentrate on paleotopographically low areas down slope from conduits; (3) deposits with stringer zones lying above normally permeable units may be underlain by regionally extensive weakly mineralized and altered zones (self-seal caps) ; (4.) in the absence of a self -sealed cap, the ore horizon may be underlain by a naturally impermeable unit (e .g. a fine clastic sediment) ; (5) the condition of cross-stratal permeability may be evidenced by features such as dykes. alignment of vari ous magmatic and hydrothermal phenomena, abrupt thickness changes in stratiform units indicative of ponding against syn-volcanic faults, and fault-scarp slump deposits; (6) the condition of high heat flow may be evidenced by near-surface magmatism and steep thermal gradients preserved in metamorphic mineral assemblages.

Jan 1, 1977

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

By M. Grodner

Ground Penetrating Radar (GPR) is an electromagnetic geophysical reflection technique that maps reflections associated with a change in electric properties of the target medium. It can thus be used to map the geometry of geological features and fractures as these can have different electromagnetic properties to intact rock. GPR was used successfully to determine the position and nature of the fractures in the tunnel sidewall, in the area of the simulated rockburst experiment. By comparing the radar scans acquired before with those acquired after the blast, it was possible to determine which fractures were reactivated by the blast and where new fractures were developed. It was found that the mining-induced fractures that formed during the development of the tunnel were re-activated by the simulated rockburst, as indicated by their increased reflectance on the radar scans. In addition, several new tunnel sidewall parallel fractures developed in the area of the blastholes. GPR thus clearly shows how and where the fracture pattern changed as a result of the blast and contributed to the understanding of the mechanisms of damage associated with the blast, and perhaps rockbursts in general.

Jan 1, 2001

By Francisco Sena Leite, Pedro Brito, Auã Kiahla, Raquel Carvalhinha, Tomi Kouvonen, Vinicius Miranda

Shockwaves that generate vibration in the surrounding environment of a blast, are one of the most important factors to control drill & blasting works near delicate buildings as well as in sensitive structures (wall control). On top of the damage to the buildings themselves, sensitive equipment such as computers, measurement apparatus and medical devices can be also compromised. The most commonly measured values from vibration are PPV (peak particle velocity), acceleration and displacement. Some devices and techniques have been developed in the last decades to measure the impacts of these vibratory phenomena. This information can be used to predict levels of vibration for future blasts and improve their quality of design using the attenuation law. From traditional studies to modern seismographs, a range of solutions are used for this propose. The main problem of applying this kind of technology is the high cost associated with each measurement device. In order to measure the ground vibration using new technologies while lowering the cost, a device has been developed using a microcontroller and electronic sensors commonly found on the market. This new equipment was tested side by side with traditional seismographs and the results were sent to a server for analysis. After several blasts, the necessary data was generated for the validation of the prototype. Through numerical mathematical processing (Taylor’s approach and numerical derivation) the original data supplied by the accelerometer’s sensors was transformed into velocity and, after the data mining, a statistics residue analysis was applied in order to evaluate if the data from the prototype and from the traditional seismographs were similar. The data from each system was used to estimate the attenuation law and the results are shown in this paper.

By D. Brady

The need for onsite gas monitoring during, or following, a major incident at an underground coal mine has long been recognised. Recommendations from inquiries following Queensland mine disasters have included ?qualified persons and equipment for rapid analysis of gas samples be available in times of emergency? and that ?this may be accomplished by either mobile laboratories or laboratories established in each mining locality.? Following the Moura No. 2 disaster, the Queensland Government allocated funds to Simtars for a mobile laboratory to respond should such a disaster occur again in the future. This vehicle was commissioned in 1997 and has been used at many mine sites under a wide range of scenarios. Simtars, armed with over ten years of operational experience with this mobile laboratory, has taken an active role in the design and construction of a modernised replacement unit. With a twenty point tube bundle system and ultrafast gas chromatograph the result is, arguably, the best equipped mobile gas analysis laboratory for mine emergency response in the world. This paper outlines the features of the new laboratory, its capabilities and the philosophy behind the design and inclusions.

Jan 1, 2012

1. Domestic Production and Use: In 1975.12 companies operated 31 primary aluminum reduction plants, with 3 firms accounting for 67% of production capacity. Washington, Oregon, and Montana accounted for 37% of the total production; Gulf Coast States 21%, Northern States 29%, and other Southern States 13%. Output of primary metal in 1975 was valued at $3.0 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Of aluminum consuming industries in 1975, building accounted for about 21%; transportation 19%; electrical 14%; packaging 18%; and consumer durables, 9%.

Jan 1, 1976

By D. Komljenovic, E. Lafontaine, J. Paraszczak

Availability of the production equipment used in underground mines has a substantial impact on production costs and, thus, on mine profitability. Appropriate collection of pertinent data and information, as well as use of adequate performance measures and their analyses, can help mine operators identify cost-effective opportunities to improve equipment availability. This paper presents study results aimed at reviewing and analyzing means and measures used to quantify equipment availability and its contributing factors (reliability, maintainability and maintenance support) in several Canadian underground mines. It overviews sources, as well as quality and quantity of relevant data and information, and examines performance measures and their definitions, as applied to surveyed mines. Problems concerning data acquisition and meaningfulness of the performance measures are discussed. The paper concludes with some suggestions and recommendations concerning several aspects of equipment availability assessment. Evidence suggests that the latter may become a more useful tool for mine operators in their efforts to reduce production cost.

Jan 1, 2008

By Donald E. Redmon

This Bureau of Mines report examines the injury experience in the quarrying industry for the years 1968-69. Twenty-eight tables for each year are presented in which disabling work injuries are summarized by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By B Cope, Y Churi

Roxgold was a small exploration company when it discovered the Zone 55 orebody at the Yaramoko project in Burkina Faso in 2010. Since this time, it has actively progressed the project with the completion of a preliminary economic assessment in 2013, a feasibility study in early 2014 and obtained full permitting for construction in January 2015. With no other underground gold mine in Burkina Faso, developing a modern and productive modern gold mine in West Africa was considered a significant challenge as Roxgold moved from explorer to producer.To facilitate this development, Roxgold engaged an international underground mining contractor to partner this development. This has enabled Roxgold to successfully develop the mine over a relatively short time frame with construction commencing in April 2015, first gold being poured in May 2016 and commercial production being achieved in October 2016.This paper discusses key elements of the project development and highlights some of the challenges faced with operating in a remote poorly developed area with a limited mining culture. Furthermore, the authors highlight the key technical and operational aspects that make the Yaramoko project a very successful development project.CITATION:Cope, B and Churi, Y, 2017. The development of the Yaramoko gold project in Burkina Faso, West Africa, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

[Allan, Andrew Thompson Creek Coal & Coal Corp., Glenwood Springs, Colo. Allen, Earl W Mine Safety Appliances, 257 Rio Grand St., Salt Lake City, Utah Allen, Louis B C. F. & I. Corp., P.O. Box 1738, Salt Lake City, Utah Allen, Thomas Chief, State Coal Mine Inspector, Colorado, Argonaut Hotel, Denver Ambler, J.B P.O. Box 591, Denver., Colo. Anderson, A. R Jeffrey Mfg. Co., Columbus, Ohio Anderson, Merlynn D U. S. Fuel Co., Hiawatha, Utah Anderson, Nephi W Books Cliffs Coal Co., Dragerton, Utah Arnston, E. K Standard Oil Co., 4601 West 26th Ave., Denver 12, Colo. Audin. Clement, Jr Paonia,Colo.]

Jan 1, 1957

By Y. Wang, K. S. E. Forssberg, A. Johansson, X. Lu

This paper presents the desulphurisation of a fine graphite powder below 80 µm by high gradient magnetic separation. The removal of pyrite (FeS2) and pyrrhotite (Fe1-xS) from the fine graphite powder was carried out with a modified version of the Sala dry HGMS with vibration assistance. In addition, a comparative study with dry and wet HGMS systems has also been performed. In order to establish the performance of the desulphurisation, a test series of varying parameters such as magnetic induction, matrix type/configuration and vibration were performed. As an equipment/process for removing sulphurous impurities from the fine graphite powder, the dry HGMS is deemed useful and comparative with the wet HGMS.

Jan 1, 2002

By Richard F. Sliwoski

The Virginia State Capitol was designed by Thomas Jefferson and constructed in 1785. The Capitol is of great historic and architectural significance to not only the Commonwealth of Virginia but to the nation. It is the oldest operating Capitol in the U.S. and required a total restoration/renovation as well as an expansion to continue to remain functional. Site conditions dictated that the expansion (a new visitor center) be placed underground on the south side of the Capitol building, requiring a 40-foot deep excavation approximately 5 feet from the Building. Because of its historic significance, every measure had to be taken to ensure the safety and function of the Capitol during construction. The construction techniques that were used to make the deep excavation and protect the historic Capitol included a tied back concrete slurry wall, jet grouting, compensation grouting, and instrumentation monitoring. This paper describes the history of the Capitol building, the techniques that were employed for construction of the deep excavation, results of the latest movement monitoring, and factors contributing to meeting the restrictive movement goals.

Jan 1, 2006

By W. Greg Maybee

Separations, which form along stratigraphic boundaries in the roofs of potash mines, pose a serious safety concern. If these separations go undetected they can lead to falls of ground. The current method of identifying the location and extent of these separations is through manual scaling (sounding) using an aluminium rod. The potash mining companies would like to have a tool, which could quickly and reliably detect these separations and distinguish between them and clay seams. This paper presents the results of field trials undertaken at various potash mines in Saskatchewan belonging to the member companies of the Saskatchewan Potash Producers Association. A ground penetrating radar instrument from RST called SUSI (stepped frequency, ultra-wideband, synthetic aperture radar instrument) was used. SUSI has the ability of working over various frequency bandwidths. Four mines were chosen for these field trials, covering the different geological characteristics encountered in the Saskatchewan potash mines: Potash Corporation of Saskatchewan?s (PCS) Allan and Lanigan Divisions, Agrium?s Vanscoy Potash Operations and IMC Potash?s K2 Mine. These field trials indicated that stepped frequency ground penetrating radar technology could be ?tuned? to identify both separations and clay stratigraphy in the softrock, potash mine environment, based on the different spectral responses of the features.

May 1, 2004

By Clifford H. Summers

This report describes an experimental program which we conducted on behalf of the U. S. Bureau of Mines, to select from currently available materials two novel systems of construction for air-restraining bulkheads to be used in control of radon-polluted air in underground uranium mines. The program included both laboratory and field tests, the latter conducted in a portion of an operating mine owned and operated by Union Carbide Corporation at LaSal, Utah. The test site was a worked-out, double entry stope having a Volume of about 2000 cubic meters, and was located immediately adjacent to an exhaust airway. The bulkheads were constructed of 15 cm x 1.5 cm timber uprights, 5 cm x 15 cm horizontal members supporting a close-fitted 13 mm plywood curtain-wall., which was covered with a low-permeability membrane to seal in the radon-polluted air. The two membrane materials selected for testing were chosen from a list of twenty-two potentially acceptable candidates using criteria such as strength, flammability, ease of application, adhesion, radon permeability, and elasticity. Thirteen of the candidates were tested in our laboratories for adhesion to plywood and to both wet and dry concrete (simulating wet and dry mine rock surfaces), and for their general physical properties, including radon permeability. The final selections made by the Technical Project Officer, and based on our recommendation, were a pre-formed ethylene propylene diene monomeric rubber (EPDM) membrane 1.12 mm thick, normally used as a roof sealant in industrial construction, and available from Carlisle Tire and Rubber Co., Division of Carlisle Corp., Carlisle, PA, and Aquafas 48-00, a water-based mastic used in a wide variety of commercial applications and available from H. B. Fuller Co., Foster Products Division, Spring House, PA. The EPDM membrane was applied as a single sheet, laminated (dry) between two layers of plywood, and the Aquafas was applied both by troweling and spraying onto a plywood surface. In the field test, radon concentrations were continuously measured before, after, and in the trapped air behind each bulkhead. Temperature, pressure, and velocity of the air in the adjacent airway were also measured and recorded continuously. Radon fluxes at the rock/air interface and through the bulkheads themselves were measured manually on a frequent basis. All continuously acquired raw data were recorded automatically on two USBM Data Aquisition Systems (DAS), and the raw data were converted into engineering units and recorded on magnetic disks by a specially programmed microcomputer that was interfaced with the DAS's. Relatively clean (i.e. low radon concentration) air was pumped into a point near the face of one test bulkhead from a location 170 meters away through vent bag. Several air curtains and two air-restraining bulkheads were erected in passageways adjacent to the test area in an effort to control both velocity and radon concentration of the air flowing past the bulkhead faces. An average concentration of approximately 500 pCi/liter at a flow of 550 m3/minute was attained as the background concentration against which leakage through the bulkheads was measured. The entire field test period extended from October, 1981 to March, 1982, a total of six months, and was subdivided into seven successive time periods: 1) site preparation 2) background measurements prior to bulkhead construction 3) passive restraint, with bulkheads in place and totally sealed 4) open bleeder period of natural convection ventilation in and out of the bulkheaded area through a 10 cm (diameter) opening, with connecting tubing; leading into an Exhaust airway 5) open bleeder period, having forced exhaust through a 1.0 cm opening using a servo-controlled fan 6) charcoal trapping period, using the servo-controlled fan to exhaust air through the charcoal traps, to test the effectiveness of such traps in removal of radon from the exhausted air 7) site decommissioning Each of the two systems tested, one incorporating the pro-formed EPDM-rubber membrane and the other utilizing Aquafas 48-00, was assessed for effectiveness in controlling radon-polluted air by observing the change in the radon concentration in the ventilation air flowing continuously over the surface of each bulkhead. The sensitivity of the observed measurements was limited by the volume flow-rate of the ventilation air and the radon concentration in that air. The data would indicate that the observed increments in radon concentration in the ventilation air moving across bulkheads B-l and B-2 were essentially zero within the limits of sensitivity of the measurements. Data from radon flux measurement taken both on the sealed ribs adjacent to the bulkheads and on the bulkheads themselves did not differ significantly from blank data.

Jan 1, 1982