Search Documents

By C. Özgen Karacan

Longwall mining is an underground mining method during which a mechanical shearer progressively mines a large block of coal, called a panel, in an extensive area. During this operation the roof of the coal seam is supported only temporarily with hydraulic supports that protect the workers and the equipment on the coal face. As the coal is extracted, the supports automatically advance and the roof strata cave behind the supports. Caving results in fracturing and relaxation of the overlying strata, which is called "gob." Due its highly fractured nature, gob contains many flow paths for gas migration. Thus, if the overlying strata contain gassy sandstones or sandstone channels, gas shales or thinner coal seams which are not suitable for mining, then the mining-induced changes can cause unexpected or uncontrolled gas migration into the underground workplace. Vertical gob gas ventholes (GGV) are drilled into each longwall panel to capture the methane within the overlying fractured strata before it enters the work environment. Thus, it is important, first to understand the properties of the gas reservoir created by mining disturbances and, second, to optimize the well parameters and placement accordingly. In this paper, the production rate-pressure behaviors of six GGVs drilled over three adjacent panels were analyzed by using conventional multi-rate drawdown analysis techniques. The analyses were performed for infinite acting and pseudo-steady state flow models, which may be applicable during panel mining (DM) and after mining (AM) production periods of GGVs. These phases were analyzed separately since the reservoir properties, due to dynamic subsidence, boundary conditions and gas capacity of the gob reservoir may change between these two stages. The results suggest that conventional well test analysis techniques can be applicable to highly complex gob reservoirs and GGVs to determine parameters such as skin, permeability, radius of investigation, flow efficiency and damage ratio. The insights obtained from well test analyses can be used for a better understanding of the gob and for designing more effective gob gas venthole systems.

Jan 1, 2009

By Stratton-Crawley R., G. E. Agar

"A study has been done of the scale-up of laboratory bench-scale flotation to continuous plant circuit performance. It was found that the impellor speed and the air flow rate influenced the results and in this case extreme values of these operating variables were required in order to reproduce the plant rougher results in the laboratory. Despite the experimental uncertainty introduced by these extreme values, it was demonstrated that the plant performance could be predicted and experimentally reproduced with bench-scale tests.IntroductionThe mineral processing industry relies heavily on batch flotation testwork to design flowsheets, evaluate reagent s and compare various types of ore. The batch tests are generally regarded as being directly comparable within themselves, but quite often they relate poorly or not at all to continuous circuits. Obviously this dilemma generates considerable uncertainty with wide-ranging ramifications. One of the manifestations of this unfortunate situation is the commonly expressed opinion that ""it may work that way in the laboratory, but it will never work that way in the plant"".In a previous publication, a method was described whereby the results of batch bench-scale tests could be used to simulate a locked cycle flotation test series. The work to be described here is a continuation of that investigation with an extension to the simulation of an actual plant circuit. It would have been preferable to progress from laboratory batch data to a continuous pilot plant and then finally to a full-scale plant operation. However, because that possibility did not present itself, an attempt will be made to show that the performance of an existing plant circuit can be successfully simulated from batch data. The success of the procedure can be judged by the agreement among the plant results, a locked cycle test and the predicted results based on batch tests."

Jan 1, 1982

By R Adamian, F. T. Da Silva, D. H. Gameiro

Schytill and Geldart diagrams were developed for the TiO2-C-Cl2 system at 1 073 and 1 273 K, so as to define the hypothetical relations between particle sizes and chlorine velocity for simultaneous fluidisation of mixtures of anatase concentrate and charcoal for carbochlorination. It was concluded that the operating limits on chlorine gas velocity will be controlled by the behaviour of the reducing agent, mainly because of its lower density. An increase in temperature from 1 073 to 1 273 K will have only a small influence on the fluid-dynamic behaviour of the mixture. For bubble fluidisation, the maximum sizes 0.413-0.478 mm for anatase and 0.529-0.611 mm for charcoal will be adequate. When the particle size distribution is large, fluidisation will be feasible only if conducted in two stages, otherwise the residence time of the small particles in the reactor will be very short. New diagrams will be needed for the gaseous chlorides in the second stage

Jun 21, 1905

Rb-Sr measurements on total-rock samples of granitic rocks from the Mount Isa region have confirmed the existence of two periods of granite-forming activity. The Kalkadoon Granite, together with the Ewen Granite and possibly an older phase of the Sybella Granite, has been shown to belong to the earlier age-group at 1760 m.y.; the Wimberu Granite and a pegmatite associated with the Sybella Granite have been dated at 1540 m.y. The initial Sr ratio suggests that the Wimberu Granite may be new material of deep-seated origin.Further Rb-Sr measurements have confirmed previously-reported K-Ar results upon biotites from these rocks, whilst showing that, in this metamorphic terrain, biotites have lost varying amounts of radiogenic Sr and Ar, and therefore yield ages which are younger than the true age of the second event.

Jan 1, 1966

By Hugo T. Dummett

I would like to share some observations about the mining business and place the ongoing discussion in the context of our changed world. The mining industry practices its trade in a universe defined by prices, laws and governments. Prices, as in what the industry is paid for what it produces, and the costs of goods and services. Laws that have to be transparent and fair. And governments that the industry prefers to be stable and supportive of the industry, and certainly not corrupt. However, the day-to-day realities of the mining business in 2000 are not what they were 10 years ago. Several events have occurred that have resulted in a less populated workplace that is obliged to work much smarter and faster. These include real declining prices for most mineral commodities; low and diminishing returns to company shareholders; massive restructuring of the industry through mergers, partnerships and alliances; gold’s changed role from reserve currency to just another commodity; the growing importance of native title and the startling imperatives of “sustainable development.” In addition, the “borderless world” now means that resource companies will need to pass the test of being responsible corporate guests who respect and enhance the social, moral and societal values of their host countries.

Jan 1, 2000

By L. E. Cardwell

This publication contains routine analyses and related source data for 377 natural gas samples from 19 States and two foreign countries. Of this total, 373 samples were collected during calendar year 1970. The remaining four samples were collected during previous years, but releases granting per-mission to publish the analyses were not received until 1970. All samples were collected as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Twelve previous publications have presented the results of 9,050 gas analyses prior to 1970. The first three, Bulletins 486,6 576,8 and 617,7 contain analyses and related source data on 5,218 gas samples collected from

Jan 1, 1971

By J. C. Martin

Stmplified equations are developed for the flow of fluids in gas drive reservoirs in which the effects of gravity can be neglected. The results show that the pressure distribution is governed by a nonlinear heat flow type of equation, and the saturation distributions are related to the pressure by the same equations QS those developed by Muskat for the average pressure and saturations in gas drive reservoirs. Unrler certain conditions the equation for the pressure can be approximated by the linear form of the heat flow equatlon. This equation tk analogous to the equation for the pressure in single-phase compressible flow The analysis reveals that the equation for the pressure in n~ultiphase flows can be obtained directly from the equation for the pressure in slngle-phase flows by simply replacing the single-phase compressibility by the total compressibility and the single-phase mobility by the sum of the mobilities of all the fluids present. Perrine's method of pressure buildup analysis for multiphme flows is based on these same substitutions. Thus, the development presented in this paper constitutes a theoretical justification for Perrine's method of pressure buildup analysis. One of the most difficult problems associated with the production of oil is the determination of the flow of the fluids within the reservoirs. One purpose of this paper is to present the development of simplified equations for the flow in gas drive reservoirs. The other purpose is to present some of the needed theoretical foundation for the methods currently being used in the analysis of multiphase pressure buildup data. The analysis presented in this paper makes use of a partial linearization of the equations governing multiphase flows. It is felt that the process of linearizing or partially linearizing the nonlinear equations of multiphase flows can lead to useful results since this process has proved extremely valuable in the study of other fields of science and engineering where nonlinear equations are encountered. Pressure buildup data of shut-in wells have been used for many years to estimate the static reservoir pressure. These data have also been used in studying the aver- age permeability both away from and close to the well-bores. The majority of the buildup data are obtained from wells producing two or three fluids. As yet the theoretical foundations for the methods of buildup analysis used in connection with rnultiphase buildup data have not been established. A number of methods of analysis of pressure buildup data have been developed." Most of these methods apply only to single-phase flows, and almost all of the theoretical analysis is confined to single-phase flows. Perrine' developed a method of analysis for rnultiphase flows from the method for single-phase flows of Miller, Dyes, and Hutchinson.' He did this by simply replacing the single-phase compressibility by the multiphase compressibility and replacing the single-phase mobility by the sum of the mobilities of the fluids in the rnultiphase flows. Obviously, such a procedure lacks a certain amount of theoretical justification, and such practices can lead to erroneous results. Fortunately, Perrine's results have a theoretical justification, and this justification is presented in the following discussion. It is assumed that gravitational effects and the cornpressibility of the rock can be neglected. Under these assumptions the equations governing the simultaneous flow of gas, oil and water in porous media areo* The preceding equations can be expanded into the following expressions.

By David A. Newman

Barrier pillars created during mine development provide additional reserves during mine closure and can be the sole access to reserves previously abandoned because of mining height or out of seam dilution limitations. The safe and successful mining of barrier pillars requires a thorough knowledge of the magnitude and distribution of the vertical stress field in addition to the strength and physical properties of the coal, immediate roof, and immediate floor strata. Quantifying the vertical stress field is complicated by the combination of the overburden stress, abutment stresses transferred onto the barrier pillar from adjacent gob areas, and in multiple seam mining, stresses transferred from abandoned subjacent mines. These variables make the extraction and development of barrier pillar reserves a site specific consideration. Three case histories are presented in which barrier pillar development and extraction provides; i) an access point and the means to ventilate a large area of low seam reserves left by a prior operator after developing only the thicker areas of a multiple split reserve, ii) the means to increase total recovery of a deep, thick seam longwall reserve, and iii) opportunities for the development and retreat mining of a two mile long barrier pillar in thick seam reserves.

Jan 1, 1995

By D. C. Crowell, A. G. Loomis

Both Dimensional and Inspectional Analysis are developed from fundamental concepts , and dimensionless groups are derived which represent the viscous , capillary , and gravitational forces existing in two - phase , incompressible flow in petroleum reservoirs . It is shown how properly scaled models may be devised by means of the foregoing groups . Laboratory measurements with such models faithfully duplicate the behavior of the reservoir on a miniature dimensional and compressed time scale , and when all the pertinent variables are evaluated , the model is a most effective tool for the study of complex fluid displacements in the reservoir . Applying the Principle of Similitude , it is shown how dimensionally scaled models are applied to various types of reservoir displacements : ( 1 ) Oil displaced by water , ( 2 ) gas displaced by water , and ( 3 ) miscible displacement . The special case of water displacing gas by imbibition is analyzed , and it is shown that the dimensionally scaled model must be fabricated of sandstone rather than unconsolidated sand , which is generally used in such models . This report is intended to be a review and summary of the application of Dimensional Analysis to reservoir displacement problems for those who are beginning the study of this useful and interesting method .

Jan 1, 1964

By M. A. Barakat

"Adsorption of heavy metal ions specifically, Cu(II), Zn(II), Mn(II), and Cr(VI) from aqueous solution on synthetic 4A Zeolite was evaluated. The 4A zeolite was synthesized previously by dehydroxylation of low grade Kalabsha Kaolin at 800 °C, and reacted hydrothermally with 2-4 M NaOH solution at 100 °C for 2h. The adsorption capacity of the metal ions were found to be strongly dependent on pH and initial metal ion concentration. At the optimium conditions the adsorption capacity decreased in the order Cu(II) > Zn(II) > Mn(II) > Cr(VI) ions. Almost complete adsorption was achieved for both of Cu(II) and Zn(II) ions at pH > 6, while the adsorption capacity for both Mn(II) and Cr(VI) was 96, and 55.3 % at pH 11 and pH 3, respectively. The results also showed that the grain size of the 4A zeolite has a little effect on the adsorption capacity. The experimental data was compared with two adsorption isotherms, Langmuir and Freundlich isotheroms. The results showed a good agreement of the Langmuir plots with the experimental data.1. IntroductionSeveral industrial wastewater streams may contain heavy metals such as Cr, Cu, Pb, Zn, Co, Ni, Mn, etc. including the waste liquids generated by metal finishing or the mineral processing industries. Heavy metals are considered hazardous pollutants due to their toxicity, even at low concentration, and nonbiodegradability. Increasing level of heavy metals in natural water bodies poses a serious threat to all living species including humans. It is, therefore, essential to reduce the heavy metal concentration in effluents/wastewater before it is discharged into the water bodies [1]."

Jan 1, 2008

By Roger Payne, John R. Goode, Feng Gao, James Brown

The Eco Ridge deposit is located in the Elliot Lake mining camp in Northern Ontario, Canada. Between 1955 and 1996, the area produced more than 138,000 t (300 million pounds) of U3O8 and very significant amounts of thorium and heavy rare earths. Based on the NI 43-101 Preliminary Economic Assessment by Roscoe Postle Associates (RPA) dated June 2012, and the economic review by RPA as announced in Pele Mountains’ Press release dated September 12, 2013, the Eco Ridge Mine Project would extract and process 46 Mt of material to produce about 19,000 t (42 million pounds) of U3O8 and about 65,000 t of rare earth oxide (REO) over a 14-year life. This paper discusses process optimization studies including beneficiation and hydrometallurgical testwork. The proposed modified flowsheet includes the flotation and processing of 1) a pyrite concentrate, 2) a dominantly light rare earth elements (LREE) concentrate, 3) a concentrate containing most of the balance of the uranium and heavy rare earths (HREE), and 4) a relatively inert tailings.

Jan 1, 2014

By P. Zhang

Previous studies have shown that separation of clay minerals from non-clay minerals is the key to economic recovery of the phosphate from the waste phosphatic clays (slime) which represent about 20- 300/0 of the phosphate mined. Small hydrocyclones of different sizes (4" and 6") were tested for sizing the slime at +10 microns in order to remove most of the clay minerals. The effect of design variables and operating parameters were evaluated. Multi-stage cycloning and the effect of dispersant were also investigated. Chemical and mineralogical analyses of different size fractions of both the underflow and overflow samples indicated satisfactorily separation efficiency.

Jan 1, 1998

U.S. demand for building and construction materials, such as construction aggregate, gypsum, and cement, remained strong in 1989. Cement imports declined slightly, representing about 17% of apparent consumption compared with 19% in 1988. Mexico, supplying 29% of the total, was the primary source of imports, followed by Canada with 21 %, Japan with 14%, and Spain and Greece with 10% each. Mexico was also the target of an antidumping petition, filed by producers in Arizona, Florida, New Mexico, and Texas, alleging that Mexican cement was being sold in these areas at less than fair value. This was the second petition filed against Mexico in the last 3 years. The International Trade Commission made a preliminary determination that the cement industry in these regions was materially injured by Mexican imports. U.S. demand improved for construction aggregate for the fourth consecutive year and was at a near-record level. The U.S. gypsum industry performed well, even though new housing starts decreased for the third consecutive year. Increased U.S. exports of gypsum wallboard and strength in the remodeling markets offset the impact of declining housing starts.

Jan 1, 1990

By Thomas C. Shapiro

This is the final article in a three-part series on microcomputers and application software in the mineral industry. The first article covered microcomputer terms and concepts. The second discussed exploration and mining software. This article will examine plant, administrative, and geotechnical software. Every effort has been made to be current in the latest software developments. Rapid change, however, is a fact of life in the computer world and any omission is inadvertent. Introduction Geotechnical disciplines have received considerable attention in software programming. Calculations are repetitive and the formulas needed to solve them are not extremely complicated. These programs are ideally suited to the microcomputer and the microcomputer is ideally suited to the consulting geologist or engineer, due to its low cost and reliability. In fact, the advent of the Apple (a registered trademark of Apple Computer Inc.) and, more recently, the IBM personal computer has caused an explosion of inexpensive software programs available to the microcomputing public. Another area that has benefited from computerization, although not in the same way, has been mineral beneficiation. Here, process control for start-up or phase-down operations has been used in newer plants for some time. Programs to perform various calculations are becoming more common as micros increase in number. Tappi Journal has a section with solutions to handheld-calculator and microcomputer problems. Process Modeling Most process modeling is still done only on mainframes. One such program is called ASPEN PLUS (a registered trademark of Aspen Technology), and a one-week course is recommended so the user can best use the program. This program is available through timesharing from University Computing Co. Programs to find an optimal solution using Linear Programming (LP) have been around for some time. Also, plant process simulation has been possible using simulation programs. Both simulation and LP are expensive to program and run. Although there are LP programs available for some micros, the user must be fairly knowledgeable about how to set up the problem. This is because each problem must be set up as a unique program that typically requires custom programming. There are some programs that can handle blending of mine crudes and examine economic parameters over the life of the mine. Plant Applications Areas relating to mine and plant applications with programs available for micros are maintenance, production reporting, inventory, accounting, and personnel scheduling. Maintenance Maintenance typically requires that certain jobs be performed in a particular sequence and parts be ordered with enough lead time for maintenance to take place on time. There is, therefore, a critical sequence of tasks that must be performed or the scheduled maintenance will not take place. Two answers needed for maintenance project scheduling are: what is the lead time needed

Jan 4, 1984

By R. A. Beall

This bulletin reviews the historical background of the cold-mold arc-melting technology, with specific references to the development that led to homogeneous zirconium ingots. Descriptions are given of modern production arc-furnaces for vacuum melting of troth exotic and conventional metals. Besides zirconium, specific data are given for production of chromium, thorium, and copper. The development of the skull-casting technique for titanium is detailed, and the application of the technique to such refractory metals as molybdenum and tungsten is described. Factors of operation of the apparatus and furnace design are considered.

Jan 1, 1968

Real Time and In Situ Measurement of Elemental Composition Using Lasers

Sep 13, 2010

Develop hydrometallurgical or pyrometallurgical recycling methods to recover valuable rare-earth compounds from various forms of NdFeB magnet scrap. Background The U.S. Bureau of Mines (USBM) has developed technology to treat and recycle a variety of wastes containing valuable and strategic metals. As part of this effort, the USBM developed a process to separate neodymium and other valuable rare earths from iron in NdFeB magnet scrap (fig. 1). Since this scrap typically contains nearly 30 weight percent neodymium and since the demand for neodymium is constantly increasing, cost-effective methods for scrap treatment could have a significant impact on industrial expenditure and materials supply in the expanding area of magnet manufacture. Approach A hydromctallurgical, H2SO4 dissolution-precipitation process provided the most effective treatment for separating rare earths from bulk NdFcB magnet scrap (fig. 2). Precipitation of neodymium-alkali sulfate double salt proved advantageous over direct precipitation of fluoride or oxalate products. This double salt is easily converted to a variety of useful rare-earth compounds, which eliminates many of the materials-handling and economic problems inherent with direct precipitation. Following rare-earth precipitation, dissolved iron was removed from the acid leach solution by precipitation as a jarosite.

Jan 1, 1993

By John C. Niedzielski, A. Frances Ackerman

The existing US-70 Bridge over the Gila River at Bylas, Arizona is planned to be replaced due to its current poor condition. The replacement bridge is planned to be a 15-span, 1,904-foot (580 meter) long bridge, the third-longest bridge in the state highway system. Within the Gila River floodplain, granular alluvial soil is underlain by cohesive lacustrine soil; bedrock was expected due to nearby terrain but not encountered within the geotechnical exploration depth of 166.5 feet (51 meters) or less. Based on the anticipated loading conditions, design scour depths and the soil conditions, the full structural loads are carried by large diameter drilled shafts; therefore accurately determining the axial capacity of the proposed drilled shafts has important practical and safety implications. The conventional methods for axial capacity determination may be overly conservative to use for design in the site’s layered granular and hard clay soils. An Osterberg cell load test was performed to obtain detailed information on the load transfer from the drilled shaft in side friction and base resistance to allow optimization of the bridge foundation design. The fullscale field test played a significant role in the design of the project’s deep foundations, notably, by incorporating the specific subsoil properties and consequently, an exact prediction of the load-settlement behavior under loading. This paper provides the results of the geotechnical site investigations, drilled shaft load testing procedures, and shaft load distribution from the load test results. Comparisons were developed between predicted axial capacities of drilled shafts using several design methodologies and the axial capacity measured from static load testing. The load test results showed that underestimation of the axial capacity is evident using conventional methodologies. The exact prediction of the load-settlement behavior under loading combined with a site-specific design approach, resulted in a substantial reduction of foundation costs due to reduced drilled shaft dimensions.

Jan 1, 2017

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

By Herbert A. Franke

ANY analysis of the aluminum situation, particularly of the factors involved in the current shortage of the metal, must consider the rapid march of events since the Munich fiasco of September 1938. At the end of 1938, the sole domestic producer of aluminum had more than a year's supply of metal on hand, having added 50,500 tons of output to stocks during the year. Not until war had been declared between the United Kingdom and Germany in September 1939 did the United States begin to make serious preparations for defense and a limited national emergency was proclaimed. Congress reflecting popular opinion, was not disposed to spend huge sums for armaments in 1939, and although 31,413 tons of aluminum was withdrawn from stocks. 107,500 tons was still on hand at the end of the year. When the President initiated a 50,000-airplane program in May 1940 the country was astounded, as previous Congressional authorizations of approximately 6000 planes for the Army by July 1911 and 3000 for the Navy by 1914 had been considered adequate.

Jan 1, 1941