Search Documents

Thermal method of diagnostic as a nondestructive monitoring is based on data logging of infrared radiation from heated surface or from the associated thermal field. Monitoring of gearcases and motors hidden faults, such as, bearing degradation (deep-seated wears and tears, fretting wear, spalling and jamming solids of revolution) is closely related to high variations in temperature. The use of portable thermal imaging devices provides considerable advantages due to: easy remote access to the unit under test even when it is operating; minimum time required to obtain information and an opportunity for a real-time diagnosis of the tested subject's condition.

Dec 6, 2010

By E. S. Shedd

Amenability studies were conducted by the Federal Bureau of Mines on an electrooxidation technique for the extraction of mercury from cinnabar ores, particularly those that are too low in grade to be furnaced or retorted economically. Oxidation was accomplished by electrolysis of the ore while slurried with brine. Mercury was dissolved through the formation of the soluble tetrachloro mercury complex, HgC142-. Mercury extractions ranged from 90 to 98 percent in 4 to 6 hours of processing time when tests were made on eight different types of cinnabar ores containing from 0.7 to 18 pounds mercury per ton ore. Salt concentration was varied from 4 to 10 weight-percent depending on whether Pb02 anodes and iron cathodes were used or whether graphite was used for both electrodes. Power consumption ranged from 17 to 64 kilowatt-hours per ton of ore treated. Ninety-nine percent of the mercury was recovered from pregnant solutions by precipitation on an active metal such as zinc, followed by distillation of the resulting amalgam at 600° C.

Jan 1, 1975

By A. Frits van Tol, Rodriaan Spruit, Jan H. van Dalen

"Abstract In recent years, there have been major problems with deep excavations in urban areas supported by diaphragm walls. In some cases, like the fatal Nicoll Highway collapse in Singapore the quality of the D-walls was not the cause. However in other projects, like the problems with the major leak in the walls of the Boston Big Dig and with leakage in a few projects in Belgium and The Netherlands was related to poor D-wall quality. Leakage through the D-walls at the joints in deep excavations led in these cases to very serious settlement behind the walls, in the case of the North- South line in Amsterdam, there was severe damage to historical buildings. This paper describes ongoing research that focusses i on acquiring more knowledge on and improvement of D-wall installation, in particular the flow process prior and during casting ii on the detection of anomalies prior to excavation and iii on the composition of the concrete mixture in view of a better and more sustainable concrete quality of D-walls.INTRODUCTIONIn the case of deep excavations in urban areas close to neighbouring buildings, diaphragm walls are one of the best feasible solutions for the retaining structure. Although the costs of D-walls generally exceed the costs of alternative wall solutions, the advantages are decisive in many situations. The main advantages of D-walls are the limited impact of the installation on the built environment, the high stiffness and bearing capacity and the retention of water, even at considerable depths. This makes Dwalls often the preferred solution for deep excavations Sometimes the D-walls are the temporary support while for the final stage a complete concrete box is constructed in the excavation. In many other cases the D-wall has the permanent function of retaining soil as well as groundwater.In the last ten years, there have been major problems with deep excavations in urban areas supported by diaphragm walls. In some cases, like the fatal Nicoll Highway collapse, 2004 , the quality of the Dwalls was not the cause. In other important failures like the collapse of the Archives in Cologne, 2008 and Dubai Infinity Tower Flooding, 2007 a combination of design and quality issues played a role. However, the major leak in the walls of the Boston Big Dig was related to poor D-wall quality (McNichol, 2000). Van Tol et al, (2010) describe a number of case studies in Belgium and the Netherlands, with leakage through the D-walls at stop end joints. In several cases with deep excavations these leakage caused serious surface settlements behind the walls. In the case of the North-South line in Amsterdam, there was severe damage to historical buildings. All these cases have generated considerable additional costs and delays, and subsequently public and political concern. Van Tol et al. (2010) present several possibilities to improve the quality of D-walls.Other disputes related to D-walls deal with the quality of the concrete and the sustainability of D-walls applied as a permanent wall. In particular the porosity of the concrete cover is sometimes problematic."

Jan 1, 2014

By F E. Grader

A linear motor properly wound can serve as a mechanism for separating paramagnetic sulphide minerals, like pyrrhotite, from other sulphides and associated gangue minerals. The effectiveness of separation depends on the energising current of the separator, the frequency of the ac cycle, and the particle size of the minerals. The speed of travel of the minerals over the surface of the separator is also a function of particle size, and appears to be constant. The movement of pyrrhotite, magnetite and iron filings of comparable size fraction (150 ¦m +74 ¦m) on the linear motor surface has been observed using a cine camera. An attempt, has been made to give a theoretical basis for the movement of the particles by calculating the minimum electrical energy required to move them. Further, the rate of decay of magnetic moment of the particles has been estimated for magnetite and it has been found that sufficient residual magnetism existed in the particles after they had been exposed to the first half of an ac cycle for them to have like polarity with the second half of the cycle. The particles are therefore repelled from the motor surface every second half of the cycle. This repulsion due to remanent magnetism is the probable cause of particle movement over the linear motor surface.

Jan 1, 1980

By Walter R. Storms

"INTRODUCTION The New Mexico potash exploration described herein was begun in February 1944 with the object of determining the amount of potash ore in the United States Potash Reserve in Eddy County by exploring the deposit from the surface with vertical drill holes. The work was completed in October of the same year after 16 holes had been drilled on the Reserve and in the immediate vicinity.The Potash Reserve is in secs. 26; 27, 34, and 35, T. 20 S., R. 29 E., Eddy County, N. Mex., about 14 miles northeast of Carlsbad, as shown on figures 1 and 1A, Drilling was done in secs. 26 and 35 of the Reserve, in section 14 to the north, end sections 2 and 56 to the east. All work was done on Governnent-owned, unleased land.The Reserve may be reached from Carlsbad by traveling to the north-east by automobile for about 14 miles on the paved U. S. highway 62. This highway passes through the southern part of the Reserve. Other parts may be reached by a State highway that passes along the eastern side of the area, then by poor dirt roads to various drilling sites. A branch of the Santa Fe Railroad also passes across the southern part of the Reserve enroute from Carlsbad to the plant and mine of the Potash Co. of America, a few miles northeast of the project and 22 miles from Carlsbad."

Aug 1, 1947

By Oliver Bowles

In 1940 the Bureau of Mines issued a report describing all the cement plants of Latin America, their design, capacity, and output, and the cement imports, exports, and requirements of the several countries. Since that time there has been such great activity in cement plant construction that a revision of the paper is highly desirable. The present compilation comprises the essential data in the previous report together with descriptions of all cement plants completed, under construction, or planned since that date and an overall picture of the supply and requirement situation of each country. Before World War I, Latin America was one of the world's largest export markets for cement. Its dependence on outside sources created no special problems of supply until the shortage of shipping and abnormally high prices of the First World War stimulated a movement toward greater self-sufficiency. Under this incentive many cement plants were constructed, and several countries were able by 1939 to manufacture enough cement for their modest needs. Substantial imports were still required for many important areas, and as the volume of demand was rapidly increasing the Latin American countries as a whole were far from self-sufficient in cement when tine Second. World War began. South and Central America depended to a large extent on European countries, chiefly Germany arid Belgium and to a smaller degree Scandinavia, United Kingdom, France, and Italy, to Supply their cement shortages. The cost of manufacture in these European countries was much lower than in the United States, and transportation expense had been kept at a particularly low level because of the two-way trade that had been developed. Ships destined for Latin American ports for coffee, tropical woods; fruits, and other native products could carry cargoes of cement on their westward voyages at very low cost In some instanced cement was taken in exchange for South American -products because cash was not available. Great Britain had withdrawn from this market to quite an extent because of low prices and because trade with its own Empire had been increasingly fostered. United States trade in cement with Latin America had been confined principally to white and other special varieties. In few places could ordinary portland cement made in the United States compete in price with the European products; although in general it was of better quality and cool d be delivered more promptly.

Jan 1, 1946

By Timothy M. Bruner, William J. Maloney

Faced with rapid growth that strained their current water supply capabilities, the Somerset Water Service in Somerset, KY decided to construct a new intake structure on the shore of Lake Cumberland. With an existing intake structure within 200', very hard limestone geology with calcite geodes, and lake level fluctuations as high as 50 ' ,this project posed many challenges. The following paper discusses how mechanical excavation techniques were used to overcome these obstacles.

Jan 1, 2001

Undisturbed minor sedimentary structures-cross-bedding, ripplemarking, scour-and-fill, slumping-are present in most of the rock types in the Willyama Series of the Broken Hill district and in the orebodies.This indicates that there has not been any significant movement of mineral matter within or into the rocks during or after metamorphism, that the rocks have not flowed during tectonic deformation or during metamorphism, and that the ore is an original sedimentary deposit in its sedimentary position.Sedimentary processes, depositional and mechanical, are indicated to explain the deposition of sedimentary metallic minerals and their concentration into large masses. The Broken Hill orebodies show evidence of these processes.INTRODUCTIONI visited Broken Hill for one week in May, 1958, at the invitation of Mr. Haddon F. King, Director of Consolidated Zinc Pty. Ltd. He asked me to examine the rocks and orebodies in the mines and outcrops at Broken Hill for:1. Sedimentary structures that might be used to determine the facing of the banding;2. Indications of the original nature of the rocks if I considered they may have been sedimentary; and3. Indications of any possible sedimentary origin for the ores.It has been stated (Gustafson et al., 1952, p. 30) that there was no indication, in the banding, of the facing of the banding, but recently B. P. Thomson had found examples of what he had interpreted as graded bedding (personal...

Jan 1, 1959

By Shahid Islam, Lucian Bogdan

Deep and large diameter drilled shafts use mostly bundles of Grade 60 (415 MPa) reinforcing bars as longitudinal reinforcement with rebar splices to make it longer. Lower Grade steel requires large number of bars which result in rebar congestion and difficulty in placing concrete. This leads to increased labor cost for fabrication and installation. By utilizing larger size and higher strength threadbar, the congestion of rebar can be reduced significantly and bundling of bars can be avoided. The lap splices are replaced with simple threaded couplers and end hooks are replaced with end terminators. Threadbar conforms to ASTM A615-15 and can be epoxy coated if required for corrosion protection. This paper describes an attractive value engineering of replacing Grade 60 (415 MPa) bundle of rebars with larger diameter Grade 75 (515 MPa), Grade 80 (550 MPa) and Grade 100 (690 MPa) threaded bars and threaded couplers in some specific drilled shaft projects in the USA. INTRODUCTION A drilled shaft which may also be referred to as drilled piers, caissons, cast-in-drilled-hole piles and bored piles is the key element to the foundation of massive structure. They are used for tall buildings, bridges and foundations for other applications such as retaining walls, sound walls, signs, or high mast lighting. Drilled shaft foundations are typically 3 to 12 feet (0.9m to 3.7m) in diameter cast-in-place deep foundation elements constructed in a drilled hole that is stabilized to allow controlled placement of reinforcing steel and concrete. Drilled shafts for transportation structures are commonly used to depths of up to 200 ft (61m) in the USA. Drilled shafts can be installed in a variety of soil and rock profiles, and are most efficiently utilized where a strong bearing layer is present. The reinforcing cage is typically lowered into position within the hole and then concrete placed through the center of the shaft, flowing from bottom to top through the reinforcement to fill the hole.

Jan 1, 2018

By D. D. Harbuck

To decrease reliance on foreign sources for the strategic and critical metals gallium and germanium, the U.S. Bureau of Mines identified and developed processing technology for two domestic sources of these metals: a Tennessee zinc residue and a Utah ore. Sulfuric acid (H2S04) solutions were used to solubilize gallium and germanium in both sources. Statistically designed experiments showed that the most important parameter for high metal extraction from zinc residue was the H2S04 concentration. At a concentration of 2.9M H2S04, 95 pct of the gallium was extracted, and at a concentration of 0.6M H2S04, 73 pct of the germanium was extracted. Controlled H2S04 concentration was also the key for high metal extractions (97 pct Ga, 87 pct Ge) from the Utah ore. Such control was achieved using a two-stage countercurrent leach circuit. Testing showed that the insoluble germanium in both the residue and ore was tied up with silica. Several methods for overcoming this problem are given. To recover gallium and germanium from the leach solutions, the solvent extractants octylphenyl acid phosphate (OPAP) (for gallium) and LIX 63-OPAP (for germanium) were identified. These extractants were tested in separate, continuous, solvent-extraction circuits yielding a gallium recovery of 94 pct and a germanium recovery of more than 90 pct.

Jan 1, 2010

By R. E. Kennedy

"INTRODUCTION In a previous publication4 results were given of numerous experiments made on the in-flammability of gas mixtures consisting of methane, hydro a. carbon monoxide, nitrogen, and carbon dioxide. Data were obtained and tables prepared giving the inflammable limits of each of these combustibles when mixed with various proportions of carbon dioxide and nitrogen. By the use of these data and the application of Le Chatelier's law, it was found possible to calculate the limits of inflammability of any gas mixture containing any or all of the above gases.Various mixtures of the five gases given above were prepared and their limits determined experimentally and then calculated. Good agreement was found between the determined and calculated results when complex gases encountered in mine safety work were tested. Of special significance was the accurate calculation of the limits of inflammability of gases from mine fires, gases from mine explosions, detonation products of explosives, blast—furnace gases, automobile exhaust gas, and other gases of a similar character.Using the method given in the above report, Yeaw5 investigated a number of industrial gases including oven, coal, producer, blue, carbureted blue, and dry quencher gases, and found the determined and calculated results to agree remarkably well, thus giving further proof of the value of such a means of determining dangerous conditions when combustible gases are encountered in practice.GASES FROM A POTASH MINEGases were recently encountered in a potash nine in New Mexico, containing the com-bustibles, methane, hydrogen, and ethane. In one special case a mild explosion occurred when these gases were mixed with the right proportions of air and ignited it therefore became necessary to know the inflammability of these mixtures in order that the proper precautions could be taken to prevent explosions."

May 1, 1932

By Rick Collins

Presentation Agenda 1.Sudbury Basin 2.Diamond Drilling 3.Planned Production 4.Safety 5.Timeline 6.Sustainable Development 7.Scope Elements 8.Progress 9.Delivery Approach 10.Owners and EPCM Roles 11.Contract Styles 12.Mine Systems & Technologies 13.Q & A

May 1, 2009

Who Macraes Mining Company Limited is can be summed up by the following statements: +         We have been New Zealand's largest gold producer for seven years +         We have one of the lowest market capitalisation per reserve ounce of the gold producers in the  Australian Gold Index +         We have a resource finding cost of less than NZ$l0 per ounce +         We have a large land bank with proven reserves +         We have an Operating Cash Margin of approximately NZ$200 per ounce +         We have reduced our Dry Milled Tonne Cost by 34% since 1992   Our Mission is to continually grow our gold business, through maximising cashflow and focusing on our value drivers being: +         Increasing reserves +         Increasing cash operating margins +         Increasing production   The real challenge is the reduction of operating costs and the optimisation of revenue, particularly in the current gold price environment.   The Company has as at 31 December 1996 total mineral resources of 6.1 million ounces and reserves of 3.4 million ounces. This together with our current cash position of approximately NZ$15 million and strong hedging book of approximately 800,000 ounces places the Company on a sound financial footing whilst positioning itself to aggressively pursue its growth strategy when gold price and market conditions improve.

Jan 1, 1997

By M Vendrup, T C. Christensen, C Dube

The adsorptive and granulate forming MetClean™ process has been used at many locations in Northern Sweden, Norway, Denmark, France, Spain, Mongolia, Japan and Australia. It has been pilot tested and used in full scale treatment plants to remove metals from:mine watersleachate from solid waste in incineration flue gasleachate from fly ash damsleachate from landfill and waste ponds.The following paper provides details of pilot and plants tests on the effectiveness of MetClean™ in removing arsenic, antimony, barium, cadmium, copper, molybdenum, nickel, radium, uranium, vanadium and zinc. Results show that MetClean™ may reduce the concentration of these metals in treated effluent water to the one part per billion (ppb) range.The paper also finds that, for specific metals, the optimal adsorption condition depends on the:pH levelmolar relation between the specific targeted metal and the addition of iron (II) or manganese (II)type of oxidation agentssalinity levelpresence of other metals.The most effective pH level varies according to the targeted metal but falls within the pH 5 to pH 11 range. A compromise pH level may be set when more than one metal is targeted for removal at the same time and through only one process step. The removal efficiency of one or both metals may be affected by operating at a compromise rather than optimum pH level.The MetClean process generates non-hazardous solid waste. Waste can then be disposed of more easily than brine or sludge.CITATION:Christensen, T C, Vendrup, M and Dube, C, 2015. Pilot tests for heavy metals removal in mine water, in Proceedings MetPlant 2015, pp 404–415 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Harry W. Campbell

A Bureau of Mines investigation identified no mineral deposits in the Lost Creek RARE II area. Sand and gravel has been mined from alluvial flood plain deposits just outside the RARE II boundary. An oil and gas lease application which includes the eastern portion of the RARE II area is pending. Abundant basalt in the area can be crushed and used as aggregate; but it could not compete with similar deposits in more favorable locations, or with cheaper substitutes such as volcanic cinders or sand and gravel which are available outside the study area closer to major markets. No indication of coal or geothermal energy resources was found. INTRODUCTION Location and Access The Lost Creek RARE II area encompasses 8,300 acres (3,400 ha) of Lassen National Forest in north-central California, about 20 mi (30 km) north of Lassen Peak. The closest city is Redding, California, 50 air mi (80 km) southwest. Peripheral access is provided by State Highway 89 passing near the western RARE II boundary (fig. 1). The Pacific Crest Trail traverses the western margin of Hat Creek Rim adjacent to the eastern boundary of the area.

Jan 1, 1983

By Julver Álvarez

El presente trabajo describe el comportamiento estructural y mineralización del estaño-cobre en la mina San Rafael, Puno. En este sentido, las pizarras de la formación Sandia del Ordovisco Superior, por metamorfismo de contacto con el intrusivo, han sido transformadas a hornfels, que junto a las cuarcitas se presentan algunas veces como una cubierta superficial sobre el intrusivo. Asimismo, los intrusivos y las pizarras son favorables para la mineralización de estaño, aunque los cuerpos del mineral son más definidos y persistentes en el intrusivo.

Sep 13, 2001

By D. Pennington

Ground-water levels and subsidence have been monitored over a longwall panel of a deep coal mining operation located in western Pennsylvania. The monitoring network includes eleven ground-water monitoring wells completed to measure water level changes in separate shallow and deep aquifer zone-, and 50-foot surveyed subsidence stations parallel and perpendicular to the panel centerline. Monthly monitoring data were collected during the premining, mining, and postmining tine periods. Aquifer testing and borehole geophysical logging were conducted during premining, and post-mining conditions to document any changes in aquifer properties and ground-water flow patterns. Results indicate ground-water declines were located with respect to the mining face and mined longwall panel. Dewatering of the deep aquifer zone caused a significant water level decline in deep wells; however, the shallow aquifer zone was isolated fro major impacts by an aquitardal layer during, the, one-year period. Transmissivity data were greatly impacted by fracturing, in the highly anisotropic aquifer system. Borehole geophysical logging indicated changes in ground-water flow patterns and zones of increased fracturing from subsidence.

Jan 1, 1984

A brief review is given of the history of the Colliery to date together with the reasons for the development of an additional seam.Investigations into the quality of the coal ami its suitability for the production of metallurgical coke and determination of the economic mining limits and coal reserves are discussed. The commencement of mining operations and the inter-seamarrangements necessary for the disposal of coal won are described with the stages in the opening out of the seam itself and the reasons for the installation of a 48-in. trunk conveyor belt. Choke and manning of face equipment are considered and also the work of secondary development and pillar extraction.It is concluded that with modern face equipment and conveyor belt lines, concentrated mining followed by immediate extraction of pillars is practicable and is giving excellent results at Burwood Colliery.INTRODUCTIONBurwood Colliery, the total holding of which now comprises some 3,140 acres of land and 1,450 acres of sea leases, has mined the Borehole Seam since 1883. The early work took place from Nos. 1 and 2 shafts at Glenrock Lagoon and later on at Nos. 3 and 4 shafts at Whitebridge to which the centre of operations shifted in 1893, shaft sinking at this latter area having commenced in 1888.As all the early operations were confined to the Borehole Seam, reserves of coal on this horizon had been considerably reduced by the mid 1930's, so a cross measure drift was driven to the Victoria Tunnel Seam which is about 300 ft. above the Borehole Seam, and fully mechanized coal winning commenced from the second seam in 1938. Subsequently this cross measure drift was extended to the Borehole Seam and complete mechanization of the south-west sections of this seam achieved by 1945.Four track mounted mechanical units were put into operation in the latter area and these worked in a southerly and...

Jan 1, 1958

By Michael Perlow Jr

A modification of the original Davisson Offset Limit (DOL) is presented for drilled foundations using soil quake (QDOL) factors ranging from 2 to 6. A further modification of the Davisson Offset Limit has also been developed using helical pile soil quake values (HDOL) based upon helix diameter. In addition, the initial tangent slope (IS) of the pile load test displacement curve is used in lieu of the calculated elastic slope (ES) to eliminate many of the uncertainties associated with determining the drilled foundation pile elastic modulus. The QDOL and HDOL load test methods do not require any graphical interpolation and provide easy simple ultimate pile capacity interpretation methods where drilled foundation pile load tests are not carried to plunging failure. Drilled foundation and helical pile load test case studies are presented to demonstrate the use of the modified soil quake QDOL and HDOL Methods.

By J. R. Nettle

The purpose of these studies by the Federal Bureau of Mines was to determine the feasibility of refining low-grade hafnium by an inert-gas-shielded molten-salt electrorefining technique to produce a hafnium metal meeting reactor specifications. The techniques were adapted from those used success-fully for titanium electrorefining. Three electrolytes containing hafnium chlorides were developed from which deposits having a Brinell hardness of 170 or below were recovered. A KC1 + NaC1 + HfC14 electrolyte produced deposits in the hardness range of 140 to 165 Brinell. Deposits with a hardness range of from 132 to 152 Brinell were pro-duced from an electrolyte composed of KC1 + LiC1 + HfC14. A third electrolyte composed of NaC1 + K3HfC17 produced deposits with a hardness as low as 139 Brinell. In a fourth electrolyte, composed of NaC1 + K2HfF6, a measure of refining was accomplished, but under the test conditions no metal meeting specifications was recovered; none was softer than 174 Brinell. A number of metallic impurities were reduced in quantity by the electro-refining process, notably iron, which normally was reduced from 250 p.p.m. to less than 50 p.p.m. Magnesium generally was reduced from 680 p.p.m. to less than 80 p.p.m. Manganese content was also reduced by the electrorefining process. Sponge containing 90 p.p.m. Mn yielded deposits containing a maximum of 50 p.p.m.; some deposits contained only 10 p.p.m.

Jan 1, 1961