Search Documents

WHY IS IT that smoke-abatement efforts do not bring more satisfactory results? The main reason is an incorrect estimate of the kind and size of the job. When an industrial community realizes that keeping the air clean is a project of similar magnitude to keeping streets clean, providing clean water, removing city waste, or guarding the moral atmosphere, then there maybe a real hope of success. We usually think of the project in too small terms. It is thought of as is the dog catcher or the boiler inspector--a matter of a man or two, a job or two, a small appropriation of variable and uncertain amount, to be abolished in a fit of economy and reestablished under pressure of a vigorous minority. Even so, it is surprising how much is obtained for the effort; but the community is rarely satisfied, for the job is bigger than it was conceived to be. Continuous, never-ceasing effort is required to clean up a smoky city. A few months of relaxation and the situation slips back some years of effort.

Jan 1, 1938

By Kenneth C. Stewart

The overall purpose of this study was to develop and evaluate, in the laboratory, instrumentation and procedures which might allow for the use of physical measurements of earmuff attenuation which would yield results equivalent to those obtained from psychophysical measures of attenuation. The ultimate goal was to evaluate techniques which might subsequently prove feasible for physical measurement of earmuff attenuation in the field. Current instruments were modified to have a response similar to differrences observed in earmuff attenuation as observed in Volume 1 of the current contract. Mining noise spectra were selected and presented to a single subject seated in a diffuse noise field. The subject wore one of the muffs evaluated in the earlier study and was also fitted with two physical sound measurement systems. A linear system measured the "outside" noise level and a linear system plus "correction" filter measured the "in-side" noise level. These measurements indicated that, under the procedures presented in this report, a laboratory method for measuring earmuff attenuation is feasible and yields results comparable to an extensive psycho-physical procedure.

Jan 1, 1980

By Turgut Yalcin

"High-grade concentrates are achieved in flotation columns primarily due to the use of thick froth layers and wash water, both of which facilitate the drainage of hydrophilic minerals from the froth. However, conventional columns employ tall, non-agitated recovery sections for bubble-particle attachment that require high headroom and special gas spargers as well as imposing particle size limitations. These disadvantages can be all alleviated by carrying out the recovery part of the process in a mechanical or pneumatic cell which generate froth more conveniently and efficiently.This paper describes the combining of mechanical and column flotation in a single unit and discusses the influence of various parameters on the performance of the system.INTRODUCTIONIn a flotation process, some of the minerals lifted up to the froth phase may drain back to the pulp due to various reasons such as weak attachment of particles to air bubbles, bursting of air bubbles, agitation of froth, etc. Weakly floating and entrained hydrophilic minerals drain at a faster rate than the strongly floating minerals, and effective exploitation of such differential drainage can lead to cleaner concentrates.For a given mineral, if the rate of flotation from pulp to froth is k1 (min·1) and the rate of drainage from froth to pulp is k2 (min""1), then the net (overall) flotation rate of the mineral, k (min-1 ), will be [Lynch et al., 1981 ]:"

Jan 1, 1997

By Zachary Mayer

Agenda ? Kidd Mine ? Background ? Problem & Opportunity ? Challenges associated to depth - Production Rates - Productive Work Time - Operational Delays - Transfer Levels - Mucking Time - Impact on Hoist ? LHD Automation ? Sandvik AutoMine Lite ? Expected Benefits Kidd Mine - Background ? Located in Northern Ontario, Canada ? Underground base metal mine operating since 1966 ? Total 148 Mt mined (2.31% Cu, 6.08% Zn, 75 gpt Ag) ? 2.35 Mt/Y from stopes as deep as 9500 ft (2.9km) below surface ? Mining method: blasthole open stoping ? Mine/Mill: 1263 employees and contractors ? 2012 National John T. Ryan Safety Award

Aug 1, 2013

By J. A. McLennan

Nickel laterite deposits are typically formed from tropically weathered mafic-ultramafic complexes. The resulting nickel concentration is found within soil horizons and is mineable with regular dozer units. At the time of mining, digging elevations are needed at selective mining units (SMUs). Moreover, for mine planning, the costs due to dilution and lost ore require mining elevations to be specified. A conditional simulation approach is used to calculate ?optimum? SMU mining elevations. Multiple realizations of the ore base surface are simulated. For a single bottom surface realization, dilution and lost ore costs are calculated over the entire vertical extent of each SMU. The optimum mining elevation is the elevation where the lowest summed cost of ?accepting dilution? and ?wasting ore? occurs. The reported SMU dilution is the cost of mining the volume of waste located below the bottom surface and above the optimum mining elevation and the reported SMU lost ore is the cost of not mining the volume of ore above the bottom surface and below the optimum mining elevation. For all ore bottom surface realizations, optimum SMU mining elevations and their associated dilution and lost ore costs are calculated and compiled to represent production uncertainty.

Apr 1, 2005

YOUR Excellency, Fellow Members of the Australasian Institute of Mining Engineers and Gentlemen:-Nearly a decade has passed since our Institute first met in New Zealand. May I, at the very outset of this second gathering, congratulate the Institute on the great progress that has been made in the interval. At the first meeting in New Zealand in the year 1903, I understand that less than 20 persons were present, and now in the large concourse before me I believe there are not fewer than 140 persons, while if every member of the Institute to-day where here there would be over 500 with usagreat change from a membership of only 250 in 1903. I feel deeply appreciative of the honour you have conferred upon me by electing me your President for the year 1911. In return for the compliment, may I ask you to believe that I shall do everythingin my power to further the interests of the Institute throughout the coming year.It is a great regret to me to realise that soon my work in New Zealand will be over. However, I trust that the new...

Jan 1, 1912

By María Eugenia Castro, Silvia Galasso, Jorge Duca, Claudia Osuna, Ernesto Esparza

"We present a procedure for treatment of non-active solutions equivalent to the solutions obtained from dissolution of ionic exchange resins used in purification of a nuclear reactor primary cooling system containing Co, Ni, Cs and its isotropic varieties as main radioactivity source. Finally it is immobilized into a ferritic matrix by calcination which avoids its future leaching into environment.In order to achieve the objective of this treatment, a bivalent and a trivalent iron salt is added to the solution. Then, either a base or an acid is added, depending on the initial pH of the treated solution, with a Cs precipitating additive in order to reduce Co and Cs by precipitation, flocculation and adsorption. Controlling the amount of precipitating reactives it is possible to modify the activity/volume rate becoming a medium into a low radioactivity waste.The leaching test result applied over the ferritic sample is lower than the minimum limit established by law. Therefore, it can be kept safely in a interim storage."

Jan 1, 2008

This volume contains a series of papers describing research conducted by the Bureau of Mines to develop or improve equipment and systems that satisfy the communication requirements of miners doing work related to rail, belt-conveyor, trackless, and hoist haulage systems.

Jan 1, 1977

I would take this, opportunity of thanking you for the high honour you have conferred on me in electing me to the responsible position of President. You may rest assured I will use my best endeavours to promote the interests of the Institute in every way that lies in my power. In reviewing the work of the past year, it is a matter for congratulation to find the Institute in a position at once so healthy and robust, and that notwithstanding the acute depression which has prevailed in the mining industry.Owing to deaths or departures from the colony, the names of six members have disappeared from the roll of membership, but you will be pleaed to learn that several new members have been elected, the register now, showing 56 Members, 25Associates and 2 Students. A complete record of the papers read and the discussions that took place will be found embodied in the splendid volume of Transactions which has just been issued, and which I am sure will be welcomed by mining engineers in all parts of the world.

Jan 1, 1901

By Eric L. Trist

The objective of this contract was to review the results of the Rushton Mining experiment in work organization and design, to explore the extension of knowledge gained from Rushton to other underground coal mines, and to conduct a search for a potential mine site for a demonstration project. The primary focus of the contract was on a search process to provide the research team with the opportunity to evaluate the different potential experimental sites, in order to select one or more with the highest potential for success. This search process also provides the various levels of union and company officials the opportunity to fully understand the context of the research before making a decision on whether to participate. While the search project failed in its attempt to locate a specific mine site, the research team believes that this is not a rejection of the actual project but rather extreme caution because of the uncertainty within the UMWA.

Jan 1, 1978

By A Brzovic, E Córdova

In an underground mine, different mining activities such as undercutting and cave progression generate redistribution in the present in situ stress field, and these changes are represented in the rock mass through induced seismicity.In order to study and analyse the induced seismicity generated in El Teniente, a block model was developed to account for the dissipated seismic energy through different areas of the mine from 1992 to 2015. More than 2.1 million seismic events were unified and classified in 3D in order to be used for the interpolations. The resultant model variables account for the accumulated energy releases in a monthly time resolution, and provide the ability to intersect different 3D entities with the stored information in the blocks, and estimate the energy evolution inside these entities.The generated model was used to analyse the geotechnical variables that determine the seismic response for the rock mass in the mine, such as geometry and direction of advance of the undercut fronts, lithological domains, and to study the ‘work’ the rock mass needed to go through in order to generate caving in areas with different stress settings.A specific area of the mine under high-stress conditions was analysed by studying the seismic energy associated with two subsidence caves interacting around the project, the modelled lithology. Using the same approach two adjacent projects are analysed to understand the released energy from the rock mass based on different stress and geotechnical settings for each project.CITATION:Córdova, E, Brzovic, A and González, R, 2016. Analysis of progressive seismicity and its correlation with geotechnical variables at the El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 835–844 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J. P. Gous, J. J. Sutherland

"Transalloys is a silicomanganese (SiMn) producer located in South Africa, and uses only local manganese ores to produce SiMn alloy. The plant operates five open submerged arc furnaces (SAFs) with an annual capacity of 180 000 t of saleable SiMn.Maintaining tap-holes is critical for effective furnace operation, allowing proper drainage of the furnace with minimal operator interference. Using a claygun and drill arrangement installed at each furnace, tapping occurs every four hours. Tap-holes are maintained through mickey replacement and brick repairs. Three furnaces have SiC tap-holes and two have graphite tap-holes.This paper gives a review of SAF operation, furnace and tap-hole design, daily tapping operation, and maintenance practices for repairing tap-holes.IntroductionDefining tap-hole life cycle, Steenkamp et al., (2016) highlighted four main steps: installation during furnace relines, day-to-day operations, tap-hole maintenance, and tap-hole repair. The authors argued that the design of the tap-hole area should allow for all four stages in the tap-hole life-cycle. Design principles for each stage were presented using silicomanganese (SiMn) production as a case study. Here we present a further analysis of the case study by providing practical examples of how the tap-hole life-cycle is managed at Transalloys during the design, operation, and maintenance of submerged arc furnaces (SAFs) applied in the production of SiMn.BackgroundTransalloys is the largest producer of SiMn in Africa. Its smelter complex is based outside the town of eMalahleni, in the Mpumalanga Province of South Africa. Transalloys was commissioned in the mid- 1960s as a high- and low-carbon ferrochromium plant based on the Perrin process. In 1967 the plant was converted to SiMn production because of constraints in the ferrochrome market (Basson, Curr, and Gericke, 2007; Bezemer, 1995). Today, the installed production capacity is 180 000 t of SiMn annually. Plant operations consists of five SAFs (see ratings in Table I), operating 24 hours a day, 365 days a year (including maintenance), involving 280 permanent employees, with up to 120 contract employees on site at any given time."

Jun 1, 2019

By Orr C. W

Continuing the systematic investigation of the influence of elements on the properties of lead(1). If the effects of additions of copper (up to 0.3%) on Port Pirie lead have now been determined in so far as creep rate is concerned.The results in the present paper contain also a survey of the influence of copper on the micro-structure of lead, a feature which has not appeared in the previous papers of this series. Further, it has now become known that creep is but little related to the more usually determined properties such as hardness and tensile strength. Since, however, these properties are of considerable importance in connection with the fabrication and use of this metal. Brinell hardness determinations have also been made and are here included.It is becoming more and more realised also that to be useful, creep data should refer to stresses of the order of those used in practice. This is due to the fact that as soon as deformation takes place, the properties of the metal are automatically changed. Lead does, of course, creep during industrial use, and probably (in lead chamber construction for example) extensions of the order of 5%...

Jan 1, 1938

By R. H. Estrada-Ruiz

This work analyses a new approach to estimates bubble size distribution of froth surfaces using artificial neural networks (ANN).Also, the robustness of ANN to interpret images with illumination perturbations, produced by light problems or dirt attached to the window of the video camera is evaluated. The experimental work was carried out in a laboratory flotation column, instrumented with an image acquisition system. The images were processed making use of a perceptron model with a hidden layer, sigmoidal transfer function and unitary bias, and the ANN trained with a back propagation algorithm. The results of validation show that ANN are reliable for learning and producing generalized predictions of the froth mean bubble diameter and bubble size distribution, when the model is trained using a database that contains information on the illumination intensity. Keywords: image analysis, neural networks, bubble diameter, bubble size distribution.

Jan 1, 2009

By K. V. Raj

In the mining industry, computational fluid dynamics (CFD) modeling is used extensively to simulate air flow in underground mines. CFD modeling of pollutant transport in open-pit mines is relatively new. Modeling the actual pit geometry of an open-pit mine and the open domain is complex. The complexity is primarily due to the faceted geometry of an open-pit mine with its numerous associated sharp features. Important issues that are not considered carefully at the geometry level are generally propagated to the subsequent processes. Several challenges and pitfalls are encountered in modeling pollutant transport in open-pit mines. These challenges and pitfalls are related to the geometry, meshing, boundary conditions, and turbulence modeling parameterization. An appropriate mesh selection is critical. A detail discussion of the meshing of the domain of an open-pit mine is presented in this paper. The selection of an appropriate turbulence model, such as kappa-epsilon (?-e), large eddy simulation (LES), Reynolds stress model (RSM), etc., to obtain the best possible solution is equally significant. This paper discusses the various challenges in modeling the pollutant transport process in an open pit and some of the approaches adopted to address these challenges.

Feb 27, 2013

By F. A. Rutledge, B. S. Webber, J. M. Moss

"INTRODUCTION The United States, with its vast resources of relatively low-grade zinc been the world's leading producer of zinc -metal for many years. The expanded zinc production during the period, 1939-44, inclusive, was induced by favorable premium prices and has depleted the known ore reserves in the United States. The 1943-44 rate of zinc production cannot long be maintained in the United States, especially if premium prices are removed. Domestic zinc reserves, have been depleted to such an extent that it is doubtful if our mines will again be able to completely and continually fulfill the needs of this country.The Bureau of Mines, anticipating a postwar consumer demand for 550,000 to 750,000 tons of slab zinc and an additional 100,000 tons for use in paints and chemicals, sent two engineers to Sedanka Island in July 1945 to investi¬gate the deposits near Biorka Harbor.ACKNOWLEDGMENTIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion the Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Nov 1, 1946

By Eleanor Abshire

THIS PUBLICATION is the third to be prepared as a result of a cooperative project by the Bureau of Ships and the Bureau of Mines for accumulating literature published on zirconium and hafnium. The undertaking also resulted in the establishment of an information center on zirconium and hafnium at the Bureau of Mines station at Albany, Oreg., for the use of research organizations and others. The present bibliography consists of references (with abstracts) to pertinent literature on zirconium. The first publication in this series was Information Circular 7771, Bibliography of Zirconium, published in April 1957. It consists of 969 abstracted reports and 645 U.S. and foreign patents. The second publication, called a supplement to Information Circular 7771, is numbered Information Circular 7830 and consists of 844 abstracted reports and 62 U.S. and foreign patents. It was published in October 1958.

Jan 1, 1962

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964

By K. G. Gorling, S. J. Wallden, N. B. Lindvall

It is the policy of The Metollurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers according to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editorial Director, Rixford A. Beals; Associate Editor, James J. Burke; Assistants, L. Capria and R. K. Larkin. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Choirmon; Dennis Carney, John Chipman, J. C. Fulton, J. H. Hollomon, H. tl. Kellogg, A. E. Lee, R. Maddin, J. D. Sullivan, and O. Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division T. B. King. Cha~rmon; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr.. and P. T. Stroup. Institute of Metals Division: Robert Maddin, Chairman. F. Lincoln Vogel, Jr., Vice-chairman, W. A. Backofen, R. W. Balluffi, J. H. Bechtold, M. B. Bever, R. S. Busk, C. G. Goetzel, Paul Gordon, C. D. Graham. Jr., Robert F. Hehe-mann, R. I. Jaffee, F. E. Jaumot, Jr., lrving R. Kramer, A. J. Leno, Horold Margolin, C. J. McHorgue, Russell A. Meussner, J. 6. Newkirk, H. W. Paxton, G. E. Pell~ssier, I. S. Servi, Alan U. Seybolt, A. J. Sholer, and Sack Wahsburn. Iron and Steel Division: J. C. Fulton, Chairman; T. B King, F. C. Langenberg, W. O. Philbrook, and T. B. Winkler. Published bimonthly by the American Institute of Mining Metallurgical and Petroleum Engineers Inc., 29 West 39th Street, New York 18, N. Y. Telephonne pennsylvania 6-9220.Petroleum Subscription Engineers$20 per year for non-AIME members in United States and North South and Central 6-9220.SubscriptionAmerica $25 toreign; $5 for AIME members. Single copies, $4.00, iinalo copies Southfpr;ign,andCentral $5 00. The AIME 'is $25not responsible for any statement made or opinion expressed in its publications Copyright 1958 1958 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . Registered coble address, AIME New York . . . Indexed in Engineering Index, Industrial Arts Index, ...and Chemical Abstracts . . . Application for second class mail privileges IS pending at New Yark, N. Y. Volume 212, Number 2.

Jan 1, 1959

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964