Search Documents

Pressure drops were measured in a column packed with glass spheres and wax particles, both in random and preferential distributions. Variables investigated included wax content, gas flow rates, and temperatures.It is shown that for random distribution of wax, pressure drop is exponentially related to wax content above the melting point of wax and that below this it increases with increasing gas rate and temperature.For preferred distribution of wax the highest increase in pressure drop is obtained with horizontal distribution of wax and the least with vertical distribution.Comparison with operating blast furnace data and application of results to practice are also included.

Jan 1, 1970

By Meghan McGrath

Third generation advance high strength steels with microstructures of acicular ferrite and retained austenite were investigated and meet mechanical property goals. A good combination of strength and ductility were achieved with duplex ferrite and austenite microstructures where cementite formation was suppressed. Transformation induced plasticity (TRIP) behavior produced rapid work hardening. The mechanical properties of two hot-rolled steels with duplex microstructures were compared and had the following compositions: (1) Fe-0.14C-13.87Mn-1.42Si-3.51Al; and (2) Fe-0.06C-14.2Mn-1.85Si-2.38Al. These steels were cast, homogenized, and hot rolled at 900ºC to obtain a refined microstructure with ultimate tensile strengths and elongations to failure of 865 MPa and 39% and 1,217 MPa and 28%, respectively. The amount of metastable austenite in both compositions decreased after tensile testing from 58% and 28% to 6% and 0%, respectively. Microstructures were characterized using optical microscopy, scanning electron microscopy (SEM), and x-ray diffraction.

Jan 1, 2010

By Jocelyn Bouchard, Claude Bazin, Sami Makni, Rolando Quispe

"Finely disseminated minerals in ores require intensive size reduction to achieve sufficient liberation for the subsequent concentration process. The use of small grinding media in conventional ball mills as a replacement for the usual 2.5 to 3.8 cm balls (1.0 to 1.5 in) produces a finer size distribution at a lower power drawn by the mill motor. However, the conditions ensuring a successful application of using small media for fine grinding are still not fully understood and some plants faced issues to keep the newly introduced steel charge inside the mill during industrial trials. The retention conditions of small media are investigated in this paper using a continuously operated 40 x 40 cm laboratory grinding mill. The tests assess the effect of the steel charge level, the slurry solids concentration and the feed rate on the rate of ejection of the grinding media. The dominant variable is found to be the filling of the mill with the grinding media, followed by the mill feed rate. Results show that increasing the slurry solids concentration within a grinding mill may be favorable for the retention of the media inside the mill.IntroductionProcessing of complex ores often requires the use of fine grinding to liberate finely disseminated minerals. Grinding requirements for a P80 of less than 0.02 mm are not uncommon, and different grinding mills are available for such application (Leonida, 2014; Pease et al., 2006; Davey, 2006; Orford et al., 2006; Nesset et al., 2006). Even conventional horizontal ball mills charged with of 2.5 cm or larger grinding media can be used for fine grinding. However, simulation (Orford and al., 2006) and plant observations (Alves and L-Bouchet, 2005; Brisette, 2010; Brisette and Roman, 2012) demonstrated the advantages of using smaller grinding media in terms of size reduction and energy consumption."

Jan 1, 2015

Peñasquito is Mexico's largest gold producer, consisting of two open pits - Peñasco and Chile Colorado - containing gold, silver, lead and zinc. Over the next three years, mining activities in the pit are expected to be focused on lower grade ore in the upper parts of the Peñasco pit while stripping is emphasized to ensure an economically optimal pit shell design to maximize the net asset value of the operation. By 2019, Peñasquito’s gold production is expected to benefit from an improvement in mined grades as it recommences mining higher grades at the bottom of the Peñasco pit and significantly enhanced metallurgical recoveries with the planned completion of the Pyrite Leach Project ("PLP").

Jan 1, 2017

By Piyush K. Dutta

This report describes the design, development, manufacture and incorporation of noise control features on a jumbo drill and the results of successful tests of this drill in surface and underground mines. The noise-reducing features developed under this program are applicable to future designs of jumbo mounted drills that can be cost effectively manufactured and have the potential to reduce noise levels at the operator's position from 115-120 dBA to 95 dBA or less without a reduction of currently attainable drilling rates.

Jan 1, 1985

By Todd M. Ruff

An average of 13 mine workers are killed each year by being run over or pinned by mobile mining equipment. At surface mines, these accidents commonly involve large dump trucks that drive over a smaller vehicle or a person that is in the dump truck’s blind spot. One method of detecting a person or another vehicle in a blind spot is to use some type of sensor technology such as radar or radio-frequency identification (RFID). Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health tested a number of commercially available and experimental sensors that monitor obstacles in a vehicle’s blind spots. None of the sensors had been previously applied to the specific problem of rigid-frame surface mining trucks. This report documents the procedures and results of tests conducted after RFID and radar systems were mounted on a 50-ton-capacity dump truck. It was determined that both RFID and radar technology show promise for detecting obstacles in the blind spots of mining equipment; however, more development work is needed to meet the unique requirements of mining equipment and the mine environment.

Jan 1, 2000

By R. Loots

High temperature creep resistant alloys are used in power plants as steam pipes and headers where they have to withstand super heated steam temperatures of up to 600ºC for the lifetime of the plant. Frequently certain portions of pipes may be subjected to excessive temperatures and consequently suffer from creep damage. Damaged portions then have to be replaced by welding new steel to the service exposed steel. Such welds will have to be subjected to a post weld heat treatment (PWHT) to relieve residual stress. During such a PWHT it is then possible for the steel to crack in the heat affected zone (HAZ) by what is known as Reheat Cracking (RHC), also known as stress relief cracking. For the present purpose the RHC susceptibility of service exposed steel was compared with that of new steel by reproducing the temperature cycle to which the HAZ will be subjected during welding in a weld simulator. This was followed by PWHT where the influence of residual stress was studied by applying a constant stress to such a weld-simulated specimen in a creep testing machine. A sharp spiral was machined along the length of the cylindrical specimen to simulate the presence of a possible weld defect. In this way it is possible to subject all portions of the simulated HAZ to the same stress intensity. For the purpose of the investigation 1/2Cr-1/2Mo-1/4V steel known to be susceptible to RHC was chosen. During testing a constant tensile stress was maintained while the temperature was increased to follow the thermal cycle prescribed for PWHT. It was found that the new steel in all instances failed by RHC along the grain boundaries in the high temperature heat affected zone. In the case of the service exposed steel the creep strength of parent metal was lower than that of new steel as a result of exposure to a steam temperature of 540°C for about 15 years. Consequently, all of the failures during testing occurred in a ductile manner by necking outside the HAZ rather than by RHC. When service exposed steel is welded to new material, it is expected that the creep strain associated with stress relaxation will mostly be concentrated in the parent steel outside the HAZ. Accordingly, it should probably not be necessary to make any extra allowance for reheat cracking during repair of steam pipes manufactured from 1/2Cr-1/2Mo-1/4V steel other than that applicable for welding new steel.

Jan 1, 2004

By D. E. Calisaya, É. Poulin, A. Desbiens, R. del Villar, A. Riquelme

"A 15 cm diameter by 732 cm height, fully automated pilot column was installed in the Agnico-Eagle’s Laronde concentrator (Québec), for evaluating the performance of newly developed sensors and advanced process control algorithms. For eventual comparison purposes, the pilot column is continuously fed with the same slurry feeding the copper-circuit third cleaner column. It is equipped with electrical conductivity-based sensors for estimating the three variables used in the multi-variable control algorithm under evaluation: froth depth, fraction of wash water underneath the interface and gas hold-up. Froth depth is regulated using a PI controller while a predictive controller is formulated as the minimization of the tracking errors of gas hold-up and bias rate, keeping several operating constraints between their practical upper and lower limits. In particular, an unreachable high set point of gas hold-up can be selected in order to maximize the bubble surface area available for particle collection, while maintaining bias rate above a minimum value required for froth cleaning. The proposed strategy may indirectly help optimizing flotation column operation by using these secondary variables, without the implementation of a real-time optimization layer.INTRODUCTION Flotation columns have already been used for more than 30 years, mainly in cleaning stages, as a result of their froth washing capabilities. Despite their widespread usage, the measurement of some pertaining variables and their use for automatic control is rather scarce. Among the most important variables directly related to the process metallurgy (concentrate grade and recovery), froth depth (hf) is the only one normally monitored and controlled. Even though commercial sensors are available, gas hold-up (eg), a variable directly related to concentrate recovery, is seldom measured and never controlled. Another important variable, bias rate (Jb) responsible for concentrate cleaning, is simply not measured at all, as there is no commercial sensor available. Therefore, besides froth depth, continuous monitoring of process variables is limited to flow rates (gas, feed, tailings, wash water), i.e. to manipulated variables. Some new available sensors have been industrially tested, e.g. the Sonar-TracTM for eg (O'Keefe, Viega & Fernald, 2007) and the McGill hold-up sensor (Tavera & Escudero, 2002). Others, for bias rate and frother concentration, have been successfully validated at laboratory scale by Laval’s LOOP researchers (Maldonado, Desbiens, del Villar & Chirinos, 2008b; Maldonado, Desbiens, del Villar & Aguilera, 2010a). Some devices have been extensively used for monitoring bubble size and space distri-bution, e.g. McGill bubble viewer (Gomez & Finch, 2007) and others."

Jan 1, 2012

By R. P. Chapman

The geochemical interpretation of results of statistical analysis of published multi-element stream sediment data from southwest and northern New Brunswick is presented. Element concentrations in southwest New Brunswick are low and comparable to element concentrations in background areas in northern New Brunswick. Deposits of copper and nickel are indicated in southwest New Brunswick. Anomalous element concentrations occur in several areas in northern New Brunswick and the elements most commonly associated with these anomalies are Cu, Pb, Zn, As and Ag; and also Mo, Wand Sb. Bedrock geology greatly influences element concentrations and may cause false anomalies. Manganese has a pronounced effect on the dispersion patterns of Co and also Zn, Mo, Pb, As, Ba and Ni. Nickel and Cr are strongly sympathetically related and this association is independent of bedrock type.

Jan 1, 1977

By R. Weideman, M. Le Roux, F. B. Waanders, Q. P. Campbell, E. Fosso-Kankeu, D. Moyakhe

"*Paper written on project work carried out in partial fulfilment of B.Eng (Chemical Engineering) degreeSynopsisSpent coffee grounds were transformed into biochar using a hydrothermal method. Some of the biochar product was pre-treated through surfactant impregnation with sodium dodecyl sulphate (SDS) to enhance its adsorption capacity. The non-treated(NT) and pre-treated(PT) biochars were characterized using FTIR spectroscopy and SEM-EDS analyses, which revealed that the products had the potential for adsorption of heavy metals from solution and confirmed the successful impregnation of biochar with SDS surfactant. The two adsorbents were then used for the removal of cadmium from solution and the adsorption behavior and capacity determined through adsorption isotherm, kinetic, and thermodynamic studies. It was found that the cadmium was adsorbed in several concentric layers on the surface of the adsorbents through a chemisorption mechanism. The PT biochar was identified as a superior adsorbent, with a capacity of qe = 10.67 mg/g compared to the NT biochar with qe = 4.82 mg/g. The adsorption of cadmium onto the PT biochar was further determined to be spontaneous and endothermic. It was therefore concluded that the PT biochar shows potential as an adsorbent and could be considered for implementation in the treatment of metal-polluted effluents. IntroductionCoal mining operations are notorious for producing large amounts of waste tailings, which are disposed of in the form of a slurry on tailings dams. This inadvertently contributes towards environmental problems (Jin, Mansour, and Thomas, 2017). Heavy metals are one of the most common pollutants that originate from solid mine waste disposal facilities, and these can leach into groundwater supplies, contaminating them and rendering the water unsuited for human consumption (Salomons, 1995). Cadmium occurs in conjunction with metalliferous ores and can cause severe damage to agricultural soils and drinking water supplies in the vicinity of mining sites (Dudka et al., 1995). It has a tendency to migrate into the surrounding vegetation, which in turn can cause harm to humans and animals when consumed (Marquez et al., 2018)."

Jul 1, 2019

By A. Cichowicz

The objective of this work is to quantify the effect of the rock mass surrounding a stope or a tunnel on the seismic signal so that the rockburst damage on the excavation can be derived. It has been shown that the transfer function of rock mass surrounding an excavation can be modelled using a damped oscillator. The method of estimating the transfer function is extended in this paper. The parameters of a damped oscillator are estimated using inversion techniques and the transfer function is modelled as a time-varying system. The technique is tested on data acquired at three different sites in two deep gold mines. Employment of a modal model of the transfer function was suitable in two cases. Application of this technique is essential to track the time variation of the natural frequency during ground motion caused by a seismic event.

Jan 1, 1999

By Frank Gómez, Solange Ríos, Jean Valencia

La eficiencia y evolución de las actividades de perforación y voladura son de gran relevancia en la actualidad debido al impacto que causa en los procesos posteriores dentro de las operaciones mineras. Sin embargo, esta actividad unitaria experimenta numerosos problemas operativos debido a la mala elección de la malla de perforación y del explosivo, lo cual causa sobre-excavación, mala fragmentación, dilución y pérdida de mineral, entre otros. El objetivo de este trabajo técnico es optimizar las actividades de perforación y voladura de la Unidad Minera San Rafael aplicando los modelos de rotura y predicción de cavidades.

Sep 30, 2022

Investigation of the Classification Operation in a Coal Pulverising Vertical Spindle Mill Coal pulverisation in power plants is a major electrical energy consumer. In 2006 more than 41 per cent of world electricity generation was from coal where pulverisers use 0.5 to 1 per cent of gross generation. Therefore, pulverisers are an important target for optimisation not only for reducing costs of power generation but also for reduction of greenhouse gas emissions. A better understanding of the operation of pulverisers is an essential requirement for their optimisation. However, little information is available, other than operating experience, on the performance of pulverisers and how these react to changes in operational variables. This study investigates the effect of changes in coal and airflow feed rates on the classification performance that occurs in an industrial scale ball-and-race vertical spindle mill in which the pulverisation and classification processes are linked together due to the separator classifier being an integral component within the pulveriser. In order to decouple the breakage and classification processes, samples were cut from upward flowing streams through sampling ports drilled on the pulveriser body at different locations. Specific sampling tools were developed. Samples collected from the pulveriser were size and density fractioned to distinguish the differences in behaviour of the components, namely coal and mineral matter. The coal flow rates on dry basis within the mill and around the separator classifier were calculated by mass balancing the multi-component data. The difference in classification behaviour of components during pneumatic transport was confirmed. The response of the circulating load in the mill (~600 to ~1100 per cent) as well as the dependency of fineness of the streams to the operating variables was demonstrated. The approach taken in this study has proved that development of a classification model for a vertical spindle mill pulverising non-homogeneous materials, eg coal, requires treating these materials as multi-component/composite substances.

Sep 13, 2010

By J. Ritchey

This report describes the engineering feasibility and economic advantages of using a mobile bridge-type cross-pit belt conveyor system in conjunction with a large dragline to excavate and transport spoils in a typical Western surface coal mine. The studies show that such a system could be built to survive operational and climatic mining conditions, and that its implementation would offer a reduction in both acquisition and operating costs versus conventional mining units of comparable rapacity. Reclamation costs can also be significantly reduced, and the total reclamation process accelerated, making the cross-pit conveyor system attractive to mine Owners and environmentalists alike.

Jan 1, 1976

Coals from the Southern Coalfield of New South Wales treated in the Port Kembla coal preparation plants of Australian Iron and Steel Pty. Ltd. differ supstantially in their characteristics. Knpwledge of performance not only enables comparison and promotes better control, but also provides the means for predicting results.Evaluation of performance of cleaning equipment has been made in terms of probable error (Ep). Results for Baum jigs, a Chance cone, heavy medium cyclones, and water washing cyclones were examined. The efficiency factors derived from the probable error were applied to the float and sink analysis, mathematically simulating operating conditions. This method was applied to the Balgownie seam.The Balgownie seam lies between the Bulli and Wongawilli seams in the coal measures of the South Coast and mining on a large scale began recently in the Bulli area. It is known locally as the Four Foot seam and exhibits rather difficult washability characteristics, due to a comparatively high middlings content. These properties and the relatively high inherent ash make careful selection of cleaning equipment essential for optimum recovery. The prediction technique is used to determine the possible results when this coal is cleaned in the Port Kembla plants. Predicted values are compared with results from full scale trial washings demonstrating the validity and accuracy of the technique.Applications of result forecasting are listed.

Jan 1, 1971

By G. S. Harper

Noise in general and drilling noise in particular have received increasing attention within the South African mining industry during the last 10?15 years. The Mine Health and Safety Committee1, during their 2003 annual summit, established two significant milestones to be met by December 2008 and December 2013. The 2008 milestone target is that of no more than ten per cent deterioration in hearing among occupationally exposed individuals, whereas the 2013 milestone target is that of less than 110 dB sound pressure levels at any place in the workplace. While these targets relate to general noise within the mining industry, it is widely believed that the most significant source of noise contributing to noise induced hearing loss (NIHL) among the underground workforce, is that of pneumatic rock drills. Data pertaining to the noise emission level of any machine is generally reported as either a sound pressure level or a sound power level of a single machine measured under free field conditions as defined in Appendix 3 of SABS-ISO 37442. However, rock drills are seldom used in isolation and underground conditions cannot be considered as free field. A methodology for the selection of rock drills on the basis of total operating cost has been developed. However, this paper focuses on the noise elements of the generic methodology and provides a model for the prediction of the composite sound pressure level and the equivalent noise exposure levels of groups of individuals from machines, used singly and in combination in an underground environment based on the sound pressure level determined according to SABS-ISO 3744 under free field conditions. The methodology includes provision for the consideration of the effect of hearing protection devices and the use of multiple machines in combination and provides an indication of the potential costs of hearing compensation.

Jan 1, 2006

By J. Gustavson, E. Mallard, F. Pirkle

The Sales Comparison Approach to estimating the value of a mineral property must always be attempted1 . In addition to other parameters, the approach depends heavily on the availability of transaction data. The consideration for the mineral property must be in form of cash, cash equivalent or other consideration. In other words, “What dollar amount did the property sell for?” Mineral properties are generally real estate, albeit frequently buried deeply under the overlying surface real estate, unless the property may be a quarry. In some states, transactions must be recorded in county courthouses, and the sale consideration must be included. In such cases, the appraiser’s job is made easy. In other locations, the sale considerations are withheld in the courthouse data; but occasionally a local transfer tax is collected and recorded. Again, the appraiser’s job is made easy by back calculation with knowledge of the legislated transfer tax percentage. The worst problem occurs when the consideration for a mineral real estate sale is totally withheld. That may occur in so-called nondisclosure states. A recent map2 of ten non-disclosure states in red is shown below. For the full color code, please refer to the footnote

Mar 2, 2022

By J. H. Daniel

The reduction of accidents will play an ever increasing role in the mining of coal and hardrock ores as mining operations become more mechanized, the equipment becomes more costly and sophisticated, and as mineral production exploits deeper and more marginal coal and ore deposits. The most effective means to reduce accidents is through the design of mining systems and equipment. Results of safety research by the U.S. Department of the Interior, Bureau of Mines, to design safer coal extraction and haulage systems and to reduce electrical accidents are presented.

Jan 1, 1991

By Frederick M. Fowkes

Dusts can be filtered out of air streams onto polymer surfaces by electrostatic trapping resulting from the spontaneous transfer of electrons upon contact between dust particles and the polymer surfaces. Such spontaneous contact electrification has been studied quantitatively in this contract with the aid of modern semiconductor charge-sensors with the aim of determining what basic principles govern the sign and magnitude of contact electrification. Information obtained by capacitance-voltage measurements of thin polymer films on silicon showed that charges as large as 4 x 1012 electrons per cm2 develop spontaneously, and that such a charge gives adhesional forces of 165 pounds per square inch (11 atmospheres). Direct measurement of dust polymer contact electrification, using silicon surface channel conductance sensors, also showed spontaneous charges of more than 1012 electrons per cm2. Some polymers can either donate or accept electrons. These included chlorinated polyethylene, chlorinated polypropylene, polyethylmethacrylate, and a copolymer of maleic anhydride with n-octadecylvinylether. Other polymers never accepted electrons but could donate electrons; these included polystyrene, pulychlorostyrune, polyvinylchloride, polyvinylacetate, a polycarbonate (Lexan), and cellulose tributyrate. Contact electrification studies were made with dusts (coal dust, a channel black, or a silica powder) contacting thin films of various polymers solvent-cast onto the semiconductor charge-sensor. Sometimes charging was instantaneous and sometimes slower, but in all but one case (coal dust on a copolymer of maleic anhydride with n-octadecylvinyl ether) the charge trunsfer was a donation of electrons by the polymer to the dust. Some

Jan 1, 1973

By Abhijit Saha

"Two analytical closed-form elastic-rigid-plastic solution methods to predict the rigid foundation behaviour on stone-column reinforced soil are compared, both of which takes into account the stone material yield within the host soil according to stress-dilatancy theory. These are the mechanistic methods developed by the author (2004, 2005) [that presently incorporates the dilatancy angle as per Schanz and Vermeer (1996)] and that developed by Pulko and Majes (2006), that takes into account the column yield as per Rowe dilatancy theory. Since optimal design of stone column necessitates optimum stress concentration on column, which is generally composed of dense gravel with/or without sand, the vertical stress on granular column is often close to its peak strength and the material dilates. To arrive at closed-form analytic solution to this complex soil-stone column interaction problem, some common assumptions like axi-symmetric soilstone column ‘unit-cell’, elastic host soil and rigid-plastic Mohr-Coulomb stone column material are combined with equilibrium and kinematic conditions. The results reflect the beneficial effect of dilatancy within the optimal range or techno-economic domain of area-ratio. The settlement predictions are compared with other analytical methods available in literature as well as with measured settlement reduction of stonecolumn reinforced ground at different subsoil conditions around the globe reported in literature.INTRODUCTIONStone columns or granular piles are frequently used in stabilization of soft clays, silts and loose silty-sands with large amount of fines. The majority of analytical methods assume infinitely wide loaded area with end-bearing columns having constant diameter and spacing that approximate to axi-symmetric conditions, and the approach is known as ‘unit-cell concept’. Several analytical solutions are available, and many of them (Aboshi et al; 1979, Balaam & Booker; 1981) are based on elastic approach considering the stonecolumn and surrounding soil as elastic materials. However, elastic methods give the ratio between the vertical stress in the column to soil (stress concentration factor) approximately equal to the ratio of constrained modulus of both materials. This ratio was found to be considerably higher than measured in the field and it is believed that elastic methods may overestimate the effects of stone columns on settlement reduction (Barksdale & Bachus, 1983). The elastic and elasto-plastic solutions presented by Balaam and Booker (1981, 1985) indicate that the problem can be idealized by assuming that the stone column is in a triaxial state and possibly yielding, such that there is no shear stress at the stone-soil interface and no yielding in the soil. Similar assumptions of stone column to be in a state of limiting equilibrium and under a triaxial stress state are considered in other methods also (Priebe; 1976, Van Impe & De Beer; 1983, Van Impe & Madhav; 1992, Saha & De; 1994, Saha; 2004, 2005, Pulko & Majes; 2006). In majority of the methods it is assumed that under load the stone-column yields at constant volume. However, the last three cases cited consider another parameter; the dilation of stone column. In Van Impe and Madhav’s (1992) and author’s (2004, 2005) method, the dilation is taken into account through the final value of the volumetric strain of column, whereas Pulko & Majes (2006) considered the stone column as Mohr-Coulomb rigid-plastic; dilating at yield in line with Rowe (1962) dilatancy theory."

Jan 1, 2015