Search Documents

By Eugene H. Skinner

This Bureau of Mines report describes the fieldwork and subsequent analysis to determine physical properties, stress distribution, and several aspects of rock behavior as a necessary evaluation for a typical mine opening. All work was done at a test site on the 3300 level, Crescent mine, Coeur d'Alene mining district, Idaho. Free field stress beyond the influence of the opening was also determined. Conventional overcore technique with the three-component borehole deformation gage developed by the Bureau of Mines was used in three drill holes. Three field verification tests were performed using a gage newly developed by the Spokane Mining Research Center in an approach herein termed "initial deformation method." Use of this method validated that aspect of overcore theory which predicts that similar deformation effect occurs in the wall rock around the perimeter of an opening in rock under stress. Also described are all drilling procedures and performances. Physical property determinations were made on rock samples obtained from the three overcore drill holes. Twelve physical properties with a total of [532] values were obtained at various drill hole orientations and depths. Exhaustive statistical tests were utilized in the analysis of these physical properties. Further elaborated are statistical inferences based on these analyses. Extensive analysis and interpretation of Crescent mine geology are also described.

Jan 1, 1974

By C Bailey, T Kojovic, M M. Hilden, M S. Powell

The Julius Kruttschnitt semi-autogenous grinding (SAG) mill model was developed by Leung in the 1980s and extensively updated to the variable rates model by Morrell and Morrison in 1996. Since then only minor upgrades have been incorporated in the version distributed in the JKSimMet simulator. A number of improvements, developed over the course of the AMIRA P9 project and in recent independent work, have now been incorporated. These improvements are based on a power-based model that directly relates the degree of breakage with energy consumption. The new size-dependent breakage function has been incorporated. The upgrades include more accurate predictions for a wide range of mill fillings (ten - 40 per cent), slurry hold-up in the mill, pebble discharge rate and the influence of changes in feed size and ball load.The paper presents the status of progress in the model development. The upgraded model will greatly enhance its application to challenging design and optimisation studies required to optimise the performance of SAG milling circuits.CITATION:Kojovic, T, Hilden, M M, Powell, M S and Bailey, C, 2012. Updated Julius Kruttschnitt semi-autogenous grinding mill model, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 71-80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

The production of metallic titanium and titanium-rich alloys in forms useful to the engineer involves the use of certain techniques not usually necessary in fabricating the commoner metals and alloys. However, not all stages in the handling and shaping of titanium-base materials require the application of unfamiliar methods. It is the purpose of this paper to indicate where the well-known techniques are applicable as well as to outline the unusual operations which are necessitated by certain chemical characteristics of titanium.In brief, the characteristics just mentioned are manifestations of the very great reactivity of titanium, especially at elevated temperatures. Liquid titanium burns vigorously when brought into contact with air. It also reacts with practically all refractories, causing damage to the latter as well as undesirable contamination of the metal. Even solid titanium undergoes serious superficial contamination when heated above 800°C. in air for more than a few minutes. In addition to an oxide skin being formed, oxygen enters into solid solution in the surface of the metal causing the latter to become hardened and eventually embrittled.Up to date, titanium has been made only on a pilot plant scale by methods which produce a spongy or powdered product. Refractory problems have prevented the development of chemical reduction methods for making titanium in the form of a liquid pool from which ingots of useful size could be cast. Therefore the first part of this paper will cover the consolidation of powdered or spongy titanium. The latter portion will provide a brief description of...

Jan 1, 1950

By Stephen P. Quin

One of the most prospective undeveloped greenstone belts in Canada, the Hope Bay greenstone belt extends over 80km in a north-south direction and is between 7 and 20km wide. The belt lies on the arctic coast and comprises mafic meta-volcanic and meta-sedimentary rocks that are bounded by Archean granite intrusives and gneisses. The greenstone package has been deformed during multiple events and is transected by major northsouth trending shear zones that appear to exert a significant control on the localization of mineralization. The Hope Bay belt contains a number of significant gold deposits hosted in a typical Archean greenstone belt and which occur in several geologic settings, including shear-hosted, lode-style and breccia-associated. Combined, the deposits host a measured and indicated resource of 1.6 million oz of gold averaging 15.7 g/t plus an inferred resource of 2.7 million oz of gold averaging 12.3 g/t. All deposits remain open to expansion. Exploration in the period 2000-2002 by Miramar includes more than 110,000m of drilling to more fully define the nature of the known deposits, while regional exploration has focused on identifying and evaluating new targets. In carrying out its programs, Miramar uses a number of techniques to improve its chances of exploration success. Activity in 2003 includes 43,000m of drilling focused on expanding resources in the Madrid area, testing the Boston deposit at depth and continuing the hunt for more discoveries. Meanwhile Miramar is advancing one of the deposits towards a production decision, based on a low capital, high return development scenario.

May 1, 2003

By A. E. Lewis

Particle morphology is a term that is used to describe the overall external shape and appearance of particulate solids. From the physical point of view, a precipitated solid is characterized primarily by the size and morphology of the particles (Sohnel andGarside, 1992). If the morphology of the crystal structures is to be related to the processing conditions, then the morphologies need to be quantified in some way. This can be achieved by using surface area measurements as well as fractal dimensions. The key idea is that rugged and indeterminate systems can be described by using a fractional number that describes the ruggedness of the system (Kaye, 1989). In other words, when the complexity of a structure, such as an agglomerate, increases with increasing magnification, it is useful to employ fractal dimensions to describe the structure. Fractal geometry proposes that, instead of attempting to measure the length of an irregular boundary, the rate at which the length of the boundary approaches infinity with increasing resolution should be calculated. Cross-sectional profiles of rugged particles can thus be quantified using the fractal dimension, and a measurement of the ruggedness of the morphology obtained. One of the additional uses of measuring the fractal dimension is that the measured value can be related to the physical properties and formation characteristics of the particle (Kaye and Trottier,1995). The morphology of nickel crystals was quantified with fractal dimension calculations of particle cross-sections. Particle cross-sections were obtained by mounting the particles in resin and polishing back. These were then photographed using Scanning Electron Microscopy and the resulting profiles analysed using the structured walk technique.

Jan 1, 2001

By R. D. Irwin, W. M. Mullins, E. A. Medina

"Various stability criteria are introduced and thermo-kinetic models for metallurgical processes are used as concrete examples for evaluation. Kinetic criteria for the process of dynamic recrystallization are proposed. These criteria are compared to the non-equilibrium thermodynamic approaches discussed in the literature. The application of macroscopic stability criteria to materials processing is then discussed.IntroductionThe mechanical behavior of metals at elevated temperature is very well predicted by any of several empirical constitutive relations. Typical is the power-law (or Swift's) form,Equationwhere r-is the stress, y is the strain and m, n , t0, y0 and Q are material constants. This form has been used with some success in the metals processing area [1]. In general, though, all of the empirical constitutive equations are static, failing to account for any dynamical properties of the system they seek to describe.The physics of warm deformation is qualitatively well understood. An example is power-law creep, where the dominant mechanism is assumed to be lattice diffusion limited climb of dislocations, which allows the strain-rate to be determined by the applied stress through"

Jan 1, 1997

By Robert G. Lundquist

This report summarizes all relevant findings and conclusions regarding capabillty of high-energy projectile impact to operate effectively in an open pit mining environment and to successfully handle secondary breakage and bench scaling problems. A silenced, aimable, mobile projectile launcher was designed and fabricated, utilizing a Government-furnished smooth-bore, 90 mm cannon. The silenced launcher was tested at the contractor's test site prior to shipment to ANAMAX Mining Company's Twin Buttes Mine near Tucson, Arizona. Demonstration tests were conducted at an inactive waste dump in the mine on 39 oversize boulders to determine the relationship between boulder size and projectile energy required for secondary breakage. The high energy projectile impact method (known by the acronym REAM -Rapid Excavation and Mining) was tested on an additional 23 boulders in the working mine and on 31 areas of potentially loose rock high on the pit walls. Most of the secondary breakage tests were successful and acceptable for open-pit mining purposes without producing large amounts of fly rock. Five of the 31 scaling tests were successful with one shot, but most of the remainder required two or more shots, and a few could not be dislodged because they were not as loose as they appeared to be, based on visual examination from a distance. Cost comparisons between the REAM method and conventional methods of secondary breakage and bench scaling are discussed. A film documentary, REAM--Mining Applications of High Energy Projectile Impact, has been produced by the contractor depicting the applications of the silenced cannon.

Jan 1, 1976

By S. H. Ash

THIS REPORT covers the third in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the work constituting Project No.3 that consists principally of the following: (a) To sink the No. 15 shaft and extend the Alden, Sugar Notch, Baltimore No.2, and Laflin shafts from their present depths to tunnel level; (b) to drive a tunnel off these shafts to connect with the western end of the tunnel in Project No.1 (Lackawanna) and to a point 1 mile south of the No. 15 shaft; (c) to construct an emergency pumping plant at the No. 15 shaft, complete with 3 centrifugal pumps of 200-cubic-foot-per-second (c. f. s.) capacity each, and a discharge-water shaft and a discharge tunnel for conducting the water from the pumping plant into the Susquehanna River; and (d) to construct a lateral tunnel 1 mile long off the main tunnel in the vicinity of the No. 15 shaft, to be known as the Wyoming lateral. The project, as outlined, is a self-contained drainage unit that will permit unwatering inundated mines and safeguarding active mines in the Wyoming Basin of the Northern field and also will handle the water in the Lackawanna Basin, thus permitting the temporary pumping plant provided in Project No.1 to be discontinued. The pumps installed in the temporary pumping plant provided in Project No.1 can then be moved to the emergency pumping plants recommended in Projects Nos. 2 and 3, to be installed as the third or standby unit.

Jan 1, 1955

By Gary A. Kingston

Rolled steel, steel forgings, and steel castings in the Pacific Northwest (Washington and Oregon) are produced principally in the Seattle, Wash., and Portland, Oreg., metropolitan areas. Steel-mill products are rolled from carbon and some alloy &eels by three companies into shapes such as reinforcing bar, rods, rounds, squares, flats, and hot-rolled strips; structural shapes, - such as angles, channels, and I-beams, also are rolled. Carbon and alloy steel ingots are poured and forged at a Seattle plant into ship shafting, drive shafts, billets, slabs, bars, rings, hooks, and other items. Static, shell, investment, and centrifugal castings are produced at 19 steel foundries in a wide range of steel specifications. All Pacific Northwest steel output is based on remelting steel scrap. Local iron ore might be used in the future to supplement steel scrap as a metal source. Ore reduction would probably be achieved by methods other than the blast furnace. Current melt-shop practice and problems are basically the same in Pacific Northwest steel plants as in cold-melt shops in other parts of the country. Quality steel production is receiving more emphasis in this region with the installation of modern analytical equipment and vacuum pouring and melting facilities.

Jan 1, 1962

By E. Martinez

The effect of ultrasonic energy transmitted through a liquid on chrysotile asbestos was investigated. Ultrasonic energy was effective in fiberization of chrysotile crudes as well as standard grades of milled asbestos fibers. Treated samples of several grades of milled fibers had increased wet bulk volumes and decreased settling and filtration rates compared to untreated fibers. Ultrasonics may be a method for fiberization of chrysotile without decreasing length or use of chemical additives that alter surface properties. Cavitation of the liquid on the surface of fiber bundles is believed to be the cause of the fiberization. It was found that ultrasonic energy greatly increased the rate of precipitation of latex on asbestos. When chrysotile asbestos fibers require additional opening or fiberization, the usual method employed is some type of high speed impact or grinding to open the fibers and produce a larger surface area. These methods always cause some degradation in length due to breaking of fibers. In addition, the efficiency of mechanical methods decreases as the diameter of fiber bundles decreases. Chemical methods have been proposed and it is claimed that fiberization down to individual fibers of 200-300 A diam is possible with some wetting agents. However, large amounts of reagent are required, approximately EDWARD MARTINEZ is with Central Research Laboratories, American Smelting and Refining Co., South Plain-field, N.J. TP 63H226. Manuscript, Aug. 12, 1963. Discussion of this paper, submitted in duplicate prior to Mar. 15, 1964, will appear in SME Transactions, September 1964, and AIME Transactions, 1964, vol. 229. 50 pct of the weight of fiber treated, and some of the wetting agent remains on the surface of the chrysotile and cannot be removed by any solvent which does not destroy the asbestos.' This investigation was directed at determining whether ultrasonic energy transmitted through a liquid would be effective in fiberizing chrysotile asbestos. Samples of asbestos crudes and commercially milled fibers were treated; settling and filtration rates of treated and untreated milled fibers were obtained. EQUIPMENT A Westinghouse Corp. ultrasonic cleaning system WEHH was used in this investigation. See Table I for a breakdown of this ultrasonic unit. RESULTS AND DISCUSSION Fiberization of Chrysotile Crudes: Samples of chrysotile crudes were pulled apart with tweezers so that coarse bundles of fiber approximately 1/16 in. in diam were obtained. The bundles were put into a bottle with 200 ml of methanol and the mixture placed into the ultrasonic tank for 30 min at a power output of 1200 w. The test was repeated using water instead of methanol. During the irradiation it was noted that the surfaces of the bundles were being fiberized. The liquid eventually became cloudy with dispersed solids. Fig. 1 is an electron micrograph of the fibers, some reduced to unit dimensions, and a fine material released by the ultrasonic energy. The platy particles in Fig. 1 were identified by electron diffraction and differential thermal analysis as brucite, Mg(OH)2, which must have been intergrown in the chrysotile crudes. Electron micrographs of bulk specimens of chrysotile have shown a fine material filling the interstices between tubular fibers.2,3 Electron diffraction patterns of the fine material collected after ultrasonic treatment indicate that it is amorphous. After decanting the solution, bundles of chrysotile remained somewhat decreased in diameter. Continuing the ultrasonic irradiation of the remaining material resulted in additional fiberization. The opening of the fibers occurred in both methanol and water. Cavitation of the liquid by the ultrasonic energy is undoubtedly responsible for the fiberization. When sound waves are transmitted through a liquid at a

Jan 1, 1963

By S. K. Murphy, S. M. Spottiswoode, A. M. Milev, D. Geyser

A portable, stand-alone instrument especially designed for recording strong ground motion was used in this study to create a large database of peak particle velocities measured underground. A total number of 39 sites located in stopes mining Carbon Leader and Ventersdorp Contact Reefs were investigated. Peak particle velocities whith values up to 3 m/s were recorded at some sites. The data recorded on the skin of the excavations were compared to the data recorded by the mine seismic networks to determine the site response. The maximum site response was obtained for source radii of between 5 m and 30 m and events locating within 200 m of the site. The extreme values of peak particle velocities were obtained in cases were the face-area lay within the source radius. Un instrument portable unique spécifiquement conçu pour enregistrer les mouvements dynamiques des terrains, a été utilisé dans cette étude pour créer une base de données importante sur la vélocité maximum des particules, mesurée en souterrain. Un nombre total de 39 sites situés dans les excavations exploitant les récifs appelés ‘Carbon Leader et Ventersdorp Contact Reefs’, a été investigué. Une vélocité maximale avec des valeurs allant jusqu’ à 3 m/s a été enregistrée sur certains sites. Les données enregistrées sur le bord de l’excavation ont été comparées aux données enregistrées par les réseaux séismiques de la mine pour déterminer la réponse du site. La réponse maximum du site a été obtenue pour des sources de rayons entre 5 m et 30 m et des évènements situés dans les 200 m du site. Les valeurs extrêmes de vélocités maximales ont été obtenues pour les cas où la zone de face se trouve à l’intérieur du rayon de la source. Ein mobiles, alleinstehendes Instrument, speziell entworfen um starke Formationsbewegungen aufzuzeichnen, wurde in dieser Studie verwendet um eine große Datenbank von Partikelspitzengeschwindigkeiten, die Untertage gemessen wurden, aufzuzeichnen. Eine Gesamtanzahl von 39 Aufstellungsorten in den Schichtabbauorten vom Carbon Leader und Ventersdorp Contact Reef wurden untersucht. Partikelspitzengeschwindigkeiten mit Werten bis zu 3 m/s wurden an einigen Standorten aufgezeichnet Die an der Oberfläche des Grubenraumes aufgezeichneten Daten wurden mit jenen Daten verglichen, die vom seismischen Netzwerk der Grube notiert wurden, um die örtliche Reaktion des Standortes zu bestimmen. Die maximale Standortreaktion wurde für Ursprungsradien von zwischen 5 m und 30 m erhalten und Ereignissen die sich innerhalb von 200 m vom Standort befanden. Die extremen Werte der Partikelhöchstgeschwindigkeiten wurdenin jenen Fällen erreicht wo sich der Abbaubereich innerhalb des Ursprungsradiuses befand.

Jan 1, 2003

By S. Maurhofer

The Uetliberg Tunnel in Switzerland is the longest tunnel in Zurich?s new Western Bypass Expressway, connecting the Birmensdorf bypass in the west with the existing Zurich-Chur national motorway in the east. Thus the tunnel links the Zurich-West motorway interchange with the Zurich-South interchange (shown in Figure 1). The Uetliberg Tunnel project comprises two parallel tubes, each about 4.4 km long. The two tunnel tubes are connected every 300 m by a transverse walkway and every 900 m by a transverse roadway (Figure 2). The SOS niches are spaced 150 m apart. Portal stations with machinery rooms are located at the west and east portals. The tunnel falls with a gradient of 1.6% from the west portal at Wannenboden to the east portal at Gänziloo. The Project costs are about CHF 1.12 billion. The carcass construction started in March 2001. The Opening of the Uetliberg Tunnel is planed in spring 2009.

By J Lööw, M Nygren, E Segerstedt, L Abrahamsson

The purpose of the paper is to discuss socially sustainable development in the mining industry and the communities surrounding the mines. The discussions are based on results from a prestudy and literature review on mining and sustainable development conducted during 2013–2014 at Luleå University of Technology in Sweden. ‘A social licence to mine’ is important for the mining industry, but the social dimension is a relatively underdeveloped dimension when it comes to sustainable development in general and the mining industry in particular, one reason probably being the lack of effective methods for capturing social impacts. The mining industry and the surrounding communities face many challenges that provide both possibilities and obstacles to socially sustainable development; eg aspects such as gender, work conditions and cultural aspects. For example, a strong mining workplace culture and community identity can create strong cohesion but also lead to excluding certain groups, rejecting new ideas and reinforcing obsolete values. Other challenges include recruitment, as well as health and safety in relation to an increased use of fly-in-fly-out, contractors and automation of mining. Some challenges relate to the effects of fluctuations in the mining market. There is a lack of research that links attitudes, policies and activities within companies to their impact on the wider community, and vice versa. Future research should also include the development of methods and indicators for social sustainability relevant for mining – in other words: how do mining companies get ‘a social licence to mine’?CITATION:Abrahamsson, L, Lööw, J, Nygren, M and Segerstedt, E, 2015. How to get a social licence to mine, in Proceedings Third International Future Mining Conference, pp 125–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By M. John Brodie

This report reviews the regulatory environment as it pertains to tailings management and disposal from mining operations, excluding coal and placer gold operations, in the state of Alaska. It is based on the EPA's staff position on an effective program to regulate mining wastes as presented in the May, 1990 Strawman II document, The unique conditions which occur in parts of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a railings disposal facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection are examined.

Jan 1, 1992

Well designed and maintained haul roads are the key to minimising truck haulage on-road hazards and costs, as well as increasing productivity. However, practically designing and managing a haul road for optimal performance is often diff cult to achieve. Poorly designed and built roads exhibit high rolling resistance - a one per cent increase in road rolling resistance can typically reduce speed on ramp by as much as ten per cent - and on the f at by up to 26 per cent. In the current economic climates, investment and operating decisions come under scrutiny. In the long run, this scrutiny returns improved efficiencies and leaner, healthier operations. The focus of this evolving evaluation process should and will certainly fall on haulage operations - simply by virtue of their contribution to overall cost of operations - often in excess of 50 per cent of total costs for deep open-pit mines. Whilst the end result - improved efficiency and reduced cost per ton hauled - is not in itself problematic, it is the route, or process followed to achieve these savings that needs to be carefully managed. We can be guided on this journey by our understanding of how a road is designed, and, critically, the interplay between a good design and safe, cost efficient haulage.This paper brief y summarises the evolution of mine haul road design, from the seminal USBM work of Kaufman and Ault in 1977, through to current geometric, structural, functional and maintenance management design components. These augmented design and management guidelines have been developed over the past decade, both in response to the requirements of mine operators for more safe and efficient haulage systems, and the truck manufacturers' requirements for a more predictable and controlled operating environment. These developments have been paralleled by the need to minimise haulage hazards, both from a health and safety perspective. Generally, both objectives have been achieved, but with some specific areas of design and operation still presenting ongoing potential health and safety hazards.The paper then summarises current design guidelines for these safety-critical issues, both from a road-design 'best-practice' and road management perspectives. Implementation of the approach is seen as a basis for reducing the potential of an under-designed mine road to lead to health and safety defects and secondly as a means of giving haul road safety and performance issues greater prominence in the minds of the road-user, operator, mine planner and designer alike.

Dec 6, 2010

By M. J. Papo, A. Muwila

Hercules? is a low nickel austenitic stainless steel developed at Mintek that has a typical composition of 9 wt% Mn, 0.05 wt% C, 2 wt% Ni, 0.25 wt% N and 16.5 wt% Cr. A more corrosion resistant version of Hercules? (Hercules? B) with 0.5 wt% Mo has also been developed. Potentiodynamic tests performed on Hercules? B in a 5 wt% sulphuric acid solution showed it to have improved corrosion resistance comparable to that of AISI 304. The effect of a varying Mn content on the corrosion resistance of Hercules? B has also been investigated and the results discussed in this paper. From the corrosion test results, it is clear that decreasing the Mn content of Hercules? B increased the corrosion rate while increasing it decreased the corrosion rate. KEYWORDS Austenitic stainless steel, %ferrite, molybdenum, manganese, nitrogen, electrochemical corrosion tests, potentiodynamic scans, microstructure, chemical analysis.

Jan 1, 2006

By Turker L

The leaching of Tellness (Norway) ilmenite concentrate in hydrochloric acid and mixed aqueous HCl-alcohol solutions at boiling temperatures was investigated. It was found that the alcohols methanol, ethanol and ethylene glycol all substantially increased the leach rate and in the case of methanol and ethanol this was achieved at lower boiling temperatures compared with aqueous HC.

Jan 1, 1986

By Dean H. Ambrose

[Mining and processing earth's materials form the basic building blocks from which many technology advancements and products are made. Virtually all metallic and non- metallic products are derived from a substance found in our earth that we blend, mold, extrude, or pulverize into something useful, the mining industry is responsible for the first step of this process: extraction from the ground. Mining particularly coal mining. poses significant risks to both humans and machines. As raw materials are]

Jan 1, 2009

By David C. Uhrin

Two improved methods have been developed to transfer microfilmed mine maps to suitable base maps showing surface features. The methods provide for (1) positioning and orienting maps; (2) merging adjacent maps; and (3) plotting maps at a common scale. One method produces an overlay mosaic of mine maps using an Integrated camera-processor. This photographic method shows the details of mine workings and is most useful for specific limited-area projects. In the second method, outlines of mine maps are digitized, manipulated, and plotted as overlays using a computer. This computer method can plot mine outlines and spatially index large numbers of microfilmed maps. Microfilmed mine maps used in this Bureau of Mines study are on file in the Mine Map Repository of the Eastern Field Operations Center. The base maps are U.S. Geological Survey 7.5-minute topographic maps. The demonstration area is located in the New Kensington East and West quadrangles, Pennsylvania.

Jan 1, 1977

By B. W. Smee

Glacial lake sediments or glaciolacustrine deposits form a significant portion of the Canadian, Scandinavian and Russian landscapes. Furthermore, 50 per cent of the Archean volcanic belts within the Canadian Shield area are covered wholly or in part by these deposits. Because of the high electrical conductivity and low hydraulic conductivity of these compact sediments, the application of geophysical (electrical) and geochemical techniques in such areas becomes a difficult task. The presence of these sediments has therefore hampered exploration for metallic sulphide deposits in some of the most important metallogenic environments of Canada. Similar problems exist in some tropical countries, such as Australia, where the overburden may be very conductive. In this paper, the extent and provenance of the glaciolacustrine deposits within the Canadian Shield are described. The geochemical and geophysical factors that hinder exploration in the clay belts are reviewed, with case histories of successful and unsuccessful applications of some of these techniques. The most successful geochemical technique used within glacial clay belts is the sampling of lodgement till beneath the clay cover, and the analysis of the heavy mineral fraction of that till. Surficial sampling has not been successfully applied. Some geophysical techniques, more specifically electromagnetic and magnetic induced-polarization techniques, have detected mineralization beneath substantially deep clay or saline overburden layers. Some suggestions have been made, such as the use of anions in hydrogeochemical surveys and the use of wide-band multi-frequency EM systems. When implemented, they will hopefully make the current geochemical and geophysical methods more effective in exploration for base metal sulphides within clay-covered terrains.

Jan 1, 1979