Search Documents

By F F. Pitard

The comparison between J Visman and C O Ingamells’ works with P M Gy’s works has been the object of intense debates in the past. Such negative debates inevitably resulted in a loss of many good opportunities. The author’s long experience in applying works of these three authors led to the pragmatic conclusion that it is relatively easy to integrate everything Visman and Ingamells created into the Theory of Sampling; therefore, it is suggested that the compatibility has been vastly overlooked, and a correction for such anomaly is recommended. It is important to emphasise that Visman and Ingamells works may be beneficial and provide relevant, harmonious additions in some areas, and ultimately offer attractive possibilities to sampling practitioners. Such additions may enhance our capabilities to predict sampling difficulties by using a stronger strategy and to design better sampling experiments that would allow us to further understand the heterogeneity of minor constituents, and especially trace constituents. Basically, the suggested integration is essential for sampling trace constituents in the environment, in food, in chemicals and in the pharmaceutical industries.CITATION:Pitard, F F, 2017. Integration of Visman and Ingamells’ works into the Theory of Sampling – a necessity to expand possibilities in sampling practices, in Proceedings Eighth World Conference on Sampling and Blending , pp 55–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By John R. Zelonka

Models made by encasing strain-gage networks in epoxy are described and evaluated. With this technique relatively complex models can be constructed in which any number of gages can be located and alined precisely. Although the gages are an integral part of the model matrix, they create no important mechanical or thermal stresses. Model construction techniques and experimental data proved reproducible and reliable. In addition, the sGlution obtained with these models to the problem of the state of stress around a circular hole in a plate subject to a plane stress condition was in agreement with theoretical, photoelastic, and finite-element solutions.

Jan 1, 1970

The global tunneling industry has many challenges, both technically and financially, with the latter likely to be a significant feature over the next few years. Many industries have ad-opted standard practices in order to overcome specific technical challenges, from which standard out-comes are anticipated. In tunneling, however, every project is unique so standardized practice is not easy. This requires original thinking and being open to adopting new techniques and technologies as they emerge. Sprayed waterproofing is a hot industry topic and a paper recently presented at the North American Tunneling conference not only discussed this methodology for achieving a dry tunnel but also how it can reduce build costs and construction time. Despite their being relatively few ?universal truths? throughout the tunneling industry, there is one opinion that appears to be shared by most in the sector, ?all tunnels leak.?

Jan 1, 2010

By W. Sondermann

"AbstractThe construction of a distribution centre of minerals for a global mining and resources cooperation demanded the control of deformations and displacement of the stack reclaimer facilities on very inhomogeneous subsoil conditions. The variation of quality from soft clay with CPT values below 1 MPa up to rock formations were the challenge in design and execution of all the foundation works.The advanced design considerations were resulting in a barrier wall system to limit the deformations of the up to 40 m deep bored pile of the stacker-reclaimers, whereas the layout of the barrier wall and the stiffness of the elements had a major impact on the residual lateral forces to be absorbed by the bearing structure.IntroductionA large international raw material distribution organisation is currently building an iron ore and pellet distribution centre on the north-western coast of Malaysia. The distribution centre will handle around 90 MTPA (million tons per annum) of iron ore and includes accompanying plants for loading and unloading iron ore and pellets, pelletizing plants as well as corresponding storage space for these raw materials. The total storage space extends about 800m north to south respectively 1400m east to west and is about 200m from the coastline. The project area is located in a wide valley basin, bounded by a range of hills to the north. The existence of soil with low bearing capability in the area designated for the plant meant that measurements for ground improvement were required in the storage areas, in order to combine the needs of iron ore and pellet storage areas with requirements of the loading facilities as the overall project demand.Project LayoutThe iron ore distribution centre and the pelletizing facility both consist of an import/export jetty, material handling facilities, pellet plant and the associated infrastructure. This publication describes the execution of ground improvement and foundation works for the loading and storage system, which consists of five rows of stockpiles and four intermediate rows of stacker-reclaimers. The total area of these systems comprises 278,881 m2 (Fig. 1)."

Jan 1, 2014

The Waimumu area, 12 km southwest of Gore, is underlain by the Gore Lignite Measures, an early Tertiary fluvial sequence approximately 500 m thick resting on Triassic-Jurassic argillitic basement. The Waimumu Quartz Gravels (Pliocene) have been deposited locally and are in part due to the localised reworking of the Gore Lignite Measures. Structurally the area is dominated by the Dunsdale Fault System, a steeply dipping series of NE trending reverse faults (Isaac and Lindqvist, 1990). The Belle-Brook, Hedgehope and Parker Road sites sampled are adjacent to the downthrown (east) side of the Hedgehope Fault.The authigenic gold-sulphide association at Belle-Brook was discovered in 1987 (Falconer, 1987: Clough and Craw, 1989). Despite a very limited amount of alluvial mining a significant quantity of authigenic marcasite has developed. Authigenic sulphide trace element analysis has shown anomalous amounts of As, Ni, Cr and to a lesser extent Zn, Pb and eu (Table 1). It has been established that the nickel occurs as a colloform banded Ni sulphide, possibly bravoite, within the marcasite (Figures 1 & 2). Arsenic and nickel (re)mobilisation are well documented in the literature. Generally As and heavy metals are mobilised in the groundwater as a result of the oxidation of sulphides (ie as a result of mining). At Belle-Brook it is reasonable to assume the authigenic sulphide trace element composition reflects either localised groundwater contamination or hydrothermal mineralisation. This poster presents some preliminary findings.

Jan 1, 2001

By J. H. Daniel

This report, summarizing the results of two studies sponsored by the Bureau of Mines, presents information on the types of mobile machines used in surface coal mines in the United States, and the amount of noise to which miners are exposed. Data consist of a calculated value of the probability of noise overexposure caused by specific equipment. These data are extrapolated to estimate the number of overexposed operators. Bulldozers were identified as the major contributors to noise overexposure, and the report presents results of a Bureau-funded program on the feasibility of providing retrofit noise control on bulldozers.

Jan 1, 1980

By A. Mazhary, T. Huff

Sensor-based ore sorting technology is a growing area of interest due to lower-grade ore deposits and higher costs of processing, among other reasons. Among the sensors currently utilized in the particle sorting industry, X-Ray Fluorescence (XRF), as the only sensor with elemental analysis capabilities, has always attracted more attention. Currently, the bench-scale amenability tests for this sensor are performed using hand-held XRF analysers. However, this testing method overestimates the performance of the XRF sorter, and therefore, the results from these tests can be misleading and are often mispresented. The work presented here was conducted on a copper mine and investigates how the sensor’s sensitivity to copper deteriorates under different testing methods. This work compares and correlates the results of an Olympus hand-held XRF analyser, static, and dynamic sorter responses with the actual grades of the rocks. The results confirmed that, the sorter response was extremely prone to blind spots. Furthermore, the results demonstrated that although the static sorter’s responses were comparable in terms of rock identification to those of the hand-held XRF analyzer and assays, the accuracy of the dynamic sorter response deteriorated both as a function of grade of the rocks as well as the potential for blind spots. INTRODUCTION Sensor-based sorting technology has been gaining increasing attention even by larger mining corporations as ore grades decrease, deposits get deeper and therefore cost of mining and processing increases. There are various types of sensors that are currently being used in the particle sorting industry such as X-Ray Transmission (XRT), Color, Electromagnetic (EM), Near-Infrared (NIR) and others. However, none of the sensors are capable of identifying and quantifying particles by the elemental content, except for X-Ray Fluorescence (XRF). XRF is a non-destructive, surficial analytical technique used to measure elemental composition of materials. X-ray fluorescence happens when a secondary x-ray (fluorescence) is released after a sample is bombarded by a primary x-ray source. From a sorting perspective, the most common and expected issues that are associated with XRF sorting are lower throughputs compared to other sensors due to particle presentation limitation as well as the need to wash the material before introducing to the sorter. However, one important issue that is mostly neglected is how the amenability tests are performed and how realistic the obtained results are. Current amenability test procedure utilises a handheld XRF analyser (such as an Olympus InnovX, as used in this work) on multiple, generally 4, sides of the rock and uses the average measured grade as a criterion for separation. While this is a widely accepted technique, it fails to consider some important factors such as exposure time and the distance between the sensor and the particle. These factors can significantly affect the sorting outcome.

Jan 1, 2019

The Bureau of Mines annually publishes statistical data reflecting technological trends in the minerals industry (metals and nonmetals except fuels). This report outlines recent developments and trends and the technology outlook for mining practices and metallurgical processing based on a review of the minerals industry during the past 2 years. A historical statistical series which indicates trends in the minerals industry has been extended with 1970 data. In addition, data are given from a 5-year Bureau of Mines cyclic canvass of froth flotation plants. Data for 1970 are compared with those of 1960 and 1965.

Jan 1, 1972

By Osama El-Fiky

There are many types of deep foundations currently being used in the San Francisco Bay Area, one of the most common being driven precast, prestressed concrete (PC/PS) piles. PC/PS piles are frequently selected for use due to of ease of installation, availability, and relatively low cost. Disadvantages of using PC/PS piles are noise, vibrations, pollution, front-end delays due to indicator pile programs, and reduced flexibility. An acceptable alternative to driven PC/PS piles was selected for construction of foundations for the heavy housing and administrative buildings at the San Francisco County Jail #3 replacement project in San Bruno, California. The pile type selected, the Auger Pressure Grouted Displacement (APGD) pile, was chosen to reduce noise, vibrations, installation time, and cost, and to allow for greater flexibility of installed pile lengths. This paper presents a case history of the use of APGD piles that were substituted for driven PC/PS concrete piles for the subject project. Standard and quick loading pile load tests were performed to confirm adherence with the design criteria originally used for the driven PC/PS concrete piles. The APGD piles were found to increase shear strength around the piles similarly to driven displacement piles. In addition, this paper presents the methodology used in monitoring APGD pile installation.

Jan 1, 2002

By L Teixeira, C J. Greet, P Karageorgos

Pyrite is ubiquitous within copper ores, and presents significant challenges to most operations in terms of its impact on copper sulfide concentrate grade and recovery.Samples of ore containing from 3 to 47 percent pyrite, with nominally the same chalcopyrite feed grade, were collected from a copper mine in eastern Australia for testing. The ores were ground under standard conditions using forged steel grinding media in the Magotteaux Mill® to determine the impact of increasing pyrite feed grade on the pulp chemistry of the system and subsequent rougher flotation response. Attempts were made to correlate the pulp chemical parameters (oxygen demand and EDTA extractable metal ions) with flotation behaviour to determine if one (or more) could be used as a metric to infer metallurgical behaviour.The observations made were then tested under different grinding environments (obtained using more electrochemically inert high chromium) grinding media to determine if they hold true.CITATION:Greet, C J, Karageorgos, P and Teixeira, L, 2015. The influence of pyrite on the pulp chemistry and copper flotation response of a chalcopyrite ore, in Proceedings MetPlant 2015, pp 175–187 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By P. J. Closmann

Steam zone growth as a function of time has been calculated for the case of constant rate steam injection into a preheated reservoir. To simplify the calculation a linear temperature profile has been assumed in the cap and base rock at the start of steam injection. The results indicate that at early times augmentation of steam zone growth due to preheating should be greatest. At longer times the steam zone development becomes close to that calculated with no preheating. INTRODUCTION With the increasing application of thermal recovery processes to recover viscous oil, cyclic steam injection has become important in many large-scale projects. In this process, the cycle of steam injection followed by oil production is repeated a number of times. At the beginning of the second and later cycles, steam is injected into a reservoir that has already been heated but that has lost part of its heat both in produced fluids and by conductive heat loss away from the injection zone. In such a case, the temperature level of the injection zone and the temperature distribution of the surrounding rock will affect the growth of the steam zone developed during the subsequent steam injection. Knowledge of the size of steam zone developed is important in determining the amount of oil displaced and the extent of heating in the reservoir. It is also useful to be able to compute the size of the steam zone for cases where thief zones take most of the injected steam. This paper presents a fairly straightforward method of estimating the steam zone developed in a preheated formation, based on certain simplifying assumptions. Some cases of steam injection into a reservoir at its original temperature have already been considered elsewhere.1-3 Because it is difficult or impossible to obtain an accurate representation of the temperature distribution in the reservoir some time after initial heating has taken place, in this work, a linear temperature profile in the cap and base rock is assumed (Figs. 1A and 1B). The linear profile has the advantage of yielding heat flow equations that

Jan 1, 1969

By I. D. Schleicher, L. H. Rorden, F. B. Curry, T. C. Moore

The purpose of this program is to extend electromagnetic (EM) techniques for use in locating miners trapped in mines as deep as 1000 m. A previously developed EM system is considered adequate for use at mines less than 300 m deep where it has a probability of detection of 54%. A system for deep mines must keep underground equipment simple, and use extremely low frequencies (ELF), sensitive receivers, and noise cancellation. The proposed location method, developed by Develco for other applications, is based on vector field measurements from two or more static sensors and computation of source location by iterative techniques. During Phase II, very sensitive search coil sensors were built and used in a separate test to verify the feasibility of atmospheric noise cancellation. A "Breadboard" location system version without cancellation, which is a fieldable test bed to evaluate receiving and location functions, was tested and supplied. Very good results were achieved from the first in-mine test with the transmitter at a depth of 380 m. It is expected the results of this work, and additional evaluation tests in the future, will be used to define the requirements for a prototype operational system.

By Robert M. Funk, James E. Lawver

The development of a laboratory and pilot-scale high-tension electrostatic flowsheet for the production of iron-ore super concentrates having silica contents in the range of 0.1% is presented, A variety of hematite and magnetite ores were tested with this flowsheet, and the pertinent metallurgical data are given. The applications and limitations of this process are brought out in terms of both practical and theoretical considerations. There have been many new developments in the past few years that have required mineral beneficiation engineers to consider new techniques for iron-ore concentration. Developments in iron powder metallurgy, and particularly the making of sheet metal directly from high-purity iron-ore concentrates, and the concept of using metallized pellets as a substitute for scrap in electric-furnace steelmaking have created demands for what is commonly referred to as iron-ore superconcen-trates. In most cases, specifications for superconcentrates are that they contain less than 0.1% total gangue, with some applications requiring less than 0.05% gangue. To produce these concentrates, new and modified processes are being developed, and the three methods receiving attention as the primary concentrating methods are: 1) Magnetic separation in which dry rotor-type equipment is used for magnetite and the high-intensity magnets are used for hematite. 2) Amine flotation. 3) "High-tension" electrostatic separation (or, elec-trodynamic concentration). This paper examines the high-tension electrostatic process in terms of its limitations and abilities for the production of iron-ore superconcentrates. A technically effective and simple flowsheet was developed through laboratory and 5 and 100-ton pilot-plant studies for the production of concentrates containing from 0.02 to 0.20% SiO, with iron recoveries between 85 and 90%. The process is also shown to be economically feasible. Laboratory Test Program Separation Characteristics: The suitability of the electrostatic high-tension method for iron-ore supercon-centration stems from the fundamental mechanism governing the process, i.e., particles are separated on the basis of differences in electrical conductivities. This conductivity is a characteristic property of minerals, and if the difference between the conductivities of two min- erals is great enough, then their separation can be performed by a high-tension machine. As shown in Figs. 1 and 2, the critical factor is the time necessary for the particle charge density, which is established by a corona discharge field, to decay to a level such that the centrifugal force acting on the particle exceeds its electrostatic, or image, force. At this point, the particle can leave the rotor at some trajectory and fall into an appropriate product receptacle. This decay time is directly proportional to electrical conductivity, and the process variables, such as feed rate, rotor speed, electrode configuration, and rotor composition, are selected to optimize the ability of the separator to resolve different conductivities. Table 1 lists the measured conductivities for some of the iron and gangue minerals used in developing the flowsheet. These results were obtained by using the conductivity cell described by Lawver and Wright.' The discharge curve of most minerals that lend themselves to super concentration by high-tension is so fast that the

Jan 1, 1971

By T Higuchi, L Lu

The quality of iron ore fines have been deteriorating, which has affected sinter quality and productivity adversely. New pretreatment and sintering technologies are therefore required to tackle the gradual change in the quality of iron ore fines. In the sintering process, iron ore fines are first granulated with fluxes such as limestone and coke breeze, and are then loaded and fired in a sinter machine. Sinter productivity and quality are heavily influenced by the reactions occurring in the sintering bed. Hence fundamental understanding of these high temperature properties of ores is urgently needed.Formation of initial sinter melt, penetration and assimilation of nucleus particles by the initial melt, and consolidation and final solidification of final sinter melt are believed to be the key sintering reactions. The assimilation and penetration phenomena have been studied separately in the literature with model particles and diffusion couples and are therefore difficult to relate to sinter quality. In addition, the effect of ore mineralogy has not been studied in detail.In this study, tablets consisting of coarse particles from various iron ore fines as nucleus particles and chemical reagents as adhering fines were made and fired under various sintering conditions to investigate the penetration and assimilation behaviour simultaneously. The degree of assimilation, pore structure, compressive strength of the resultant analogue sinters were evaluated and the relationship between sinter strength and ore characteristics was further discussed. The nucleus particles from Ores A and B were found to be more porous and assimilated more readily with sinter melt, resulting in a viscous melt and a macro-porous sinter structure. The nucleus particles from Ores C and D on the other hand, assimilated less readily with sinter melt, resulting in a fluid melt and a denser sinter structure. This is consistent with the results reported in the literature, suggesting that the present evaluation method can be utilised for studying sintering reactions and predicting sinter quality.CITATION:Higuchi, T and Lu, L, 2017. Evaluation of sintering behaviour based on ore characteristics, in Proceedings Iron Ore 2017, pp 303–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By W. J. Mcgaughey

A crosshole seismic imaging (tomography) experiment has been carried out in an underground mine in order to delineate waste rock within a massive sulphide ore body. Data comprising 1526 travel time measurements were inverted to yield a compressional wave speed image consistent with, and adding to, knowledge of the extent of the waste inclusions. An effective method of resolving travel time discrepancies measured on reversed ray paths is presented.

Jan 1, 1989

By S. V. Burr

"A 28-year study of cross folds leads to the conclusion that the northwest-southeast folds recognized in many areas of North America are part of a regional pattern. Detailed examination of over 650 geological maps and reports of Ontario indicates that this folding can be traced across the province. Evidence is presented that this fold pattern played an important part in determining the pattern and scale of intrusion, that its recognition in the field can aid in defining stratigraphy, folding and faulting, and that it may have played an important role in channeling hydrothermal or magmatic mineralization. IntroductionThe concept of regional cross folding in Ontario is not new. W.H. Gross (1955) discussed regional cross folds in the Archean of Northwestern Ontario, and A.M. Goodwin (1961) referred to regional cross folds in the Archean of Ontario and Quebec. However, the interpretation in this paper is new.The writer saw a cross fold for the first time, underground, at Little Long Lac Gold Mines in Geraldton, Ontario, in 1951. This recalled the ""transverse folds"" on E.R. Faribault's classical maps of Nova Scotia, published by the Geological Survey around the turn of the century; M.E. Hurst's cross fold(s) at Timmins, Ontario (Figure I); and the cross folds mapped by A.W. Jolliffe in the Yellowknife area of the Northwest Territories. All these mapped cross folds had one thing in common with the fold at Little Long Lac: A northwest-southeast axial trend. Were such cross folds of purely local extent, or might they be indicative of a widespread regional fold pattern? If so, has such folding any significance for mineral exploration or potential?By 1959, based on a study of about 1000 Canadian geological maps and reports, including 291 in Ontario, the writer reached the conclusion that cross folding trending northwest-southeast is so widespread as to constitute a pattern of folding, and that such cross folding should produce changes in plunge along pre-existing greenstone fold belts."

Jan 1, 1980

By Deno M. Pappas

This report presents results of a U.S. Bureau of Mines study of longwall gob material. The objective of this work was to determine material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining, Photographs of actual mine gob were digitized to obtain approximate particle size gradations of gob material. The gradation curve was shifted down to a laboratory scale, and 20 uniaxial compression tests were conducted. Varying the maximum particle size was not found to affect the stress-strain behavior, but changing the gradation appeared to influence the stress-strain behavior. The stress-strain relationship of the simulated gob material was nonlinear, the stress-secant-modulus relationship was approximately linear, and the stress-tangent-modulus relationship was approximately a second-order polynomial function. Equations were generated from these curves, providing numerical modelers with a means to estimate gob moduli based on the stress level. In addition, the experimental data were statistically evaluated using multiple regression analyses, producing a series of equations to predict the secant and tangent moduli from the given stress level, bulking factor, rock strength, and thickness-to-width shape ratio of the particles.

Jan 1, 2010

By Å. Kruukka, H. F. Broicher

The iron ores of the Kiruna mine in Sweden are of exceptional quality except for the phosphorus content in certain zones of the orebody. The prevention of mixing ores high in phosphorus with those low in phosphorus has always been of significant economic importance. The ongoing introduction of tele-mining and automatic haulage by LHDs requires new means in the field of quality control underground, as the experienced miner as well as the underground laboratory assistant no longer are involved in the process. As of 1998, LKAB has been testing prototypes of LIF (laser-induced fluorescence) analyzers for non-contact and real-time measurement of the phosphorus content of ore being transported by LHDs from the stopes to the respective ore pass assigned to a certain ore quality. The principles of the analysis of laser-induced fluorescence, the different test phases and results are described and conclusions made. With bulk sorting of ore underground, the mining engineer supports the efforts of the metallurgist in the processing plant.

Jan 1, 2002

By Robert A. Harrow

This report documents the results of the development and installation of an illumination system for an underground coal mine Shortwall Mining Section. Also presented are the techniques used for the above ground test and evaluation of the lighting system prior to installation underground which resulted in the issuance of a Statement of Test and Evaluation (STE) from the Mine Safety and Health Administration, Technical Support, Beckley, West Virginia.

Jan 1, 1979

The ventilation conditions at the underground coal mines are influenced; first: by the disturbances of the natural nature (barometric pressure, methane liberation, etc.), and second: by the disturbances caused by the production process. The major goal of this study was to determine the changes of the ventilation parameters, such as the flow, pressure and methane concentration around the longwall panel, particularly, along the longwall face due to the shearer operation (motion). It is well known from the practice, that the movement of the shearer influences the ventilation parameters around the longwall panel, including the gob area. Until now, these data were gathered in a single or multiple locations at the different time. However, only the simultaneous measurements of all of these values allow seeing the time dependent interrelationships between measured parameters. To be able to show these interrelationships, special experiments, described in this paper, were carried out by the author. These experiments were prepared and executed at the BUDRYK Coal Mine in Poland. During each experiment a simultaneous measurements and monitoring of the barometric pressure, air velocity and methane concentration at the different locations along the longwall face, were performed. The investigation was possible by using a special setup of instruments with a short sampling time, i.e., within 2 seconds. The monitoring of the absolute pressure was conducted by using the digital barometer µBar, developed by EMAG, based on the SETRA pressure transducer, model 470. The velocity of air was measured using the electronic vane-anemometers, developed by IMG-PAN. The methane concentrations were measured using methanometers as the part of the EMAG automatic gas monitoring system. The investigation data confirmed that disturbances due to the operation (motion) of the shearer at the longwall face have a local character. It could be also seen that a large diameter shearer (compared to the total cross-section area available for the air flow) is acting as the piston compressing the air (the overpressure) ahead of the shearer. This fact affects the methane mixing process and flow patterns in the vicinity.

Jan 1, 2009