Search Documents

By Jaan Kiusalaas

This report is a self-contained User Manual for a computer program called SPASID -- Subsidence Prediction and System Identification. The program has two primary functions: (i) Precalculation of ground movements due to underground mining operations using the influence function method; (ii) Computation of influence function and site parameters from measured displacements. SPASID is written in FORTRAN and consists of four modules: (i) Preprocessor Module that prepares and maintains surface and mine data bases; (ii) Subsidence Computation Module that predicts movements of the surface; (iii) System Identification Module which is used to calculate the optimal influence function parameters, and (iv) Postprocessor Module for generating graphic displays of subsidence data. The last module is somewhat machine dependent but has internal documentation to indicate potential changes. All of the modules may be run in either batch or interactive mode. The manual does not assume previous knowledge of the influence function method or programming competence.

Jan 1, 1983

By Martyn F. Roetter

The objectives of the work described in this report are to determine the communications requirements and need for communications, both for voice and control, on longwalls, and to make recommendations for longwall communications equipment and systems. These recommendations are designed to guide the future development of longwall communications. Information necessary for the accomplishment of this work has been gathered by a series of visits to longwall mines and discussions with longwall mine operators, as well as with suppliers of longwall communications and mining equipment and with Bureau of Mines personnel. In addition, it has proven possible, through personal interviews and literature evaluation, to gain an understanding of the experience and attitudes towards longwall communications in countries where longwall mining is far more widespread than in the U.S., namely the Federal Republic of Germany, the United Kingdom, France and Belgium.

Jan 1, 1976

By John Chadwick

In the drive for faster development advance rates, railbound systems can be advantageous, in the right application. Skanska BS, the contractor to mine-owner VSK Mining, is driving an adit access deep into the Volouské Urchy Mountain in Slovakia to access the Gemerská Poloma talc deposit, some 70 km (43 miles) west of Ko?ice, the economic and cultural center of eastern Slovakia. Skanska began driving the Stolna Elisabeth drift in February 2007, extending 25 kg/m (50 lb/yd) rails (with 750 mm or 30 in. between sleepers) into the mountain to provide the main haulage to bring talc ore and waste out of the new mine once it gets into production. It will also be used for personnel transport, and is now almost complete. As a second egress and for ventilation, a 2.5-m- (8.2-ft-) diameter shaft of about 300-m (984-ft) depth will be sunk from surface down into the orebody. Stolna Elisabeth is a 4.2-km- (2.6-mile-) long drift mined at a cross section of some 11 m2 (118 sq ft). The finished profile is 3.2-m- (10.5-ft-) wide by 3.6-m- (11.8-ft-) high. It has been developed on a very slight incline so that water runs down it to the portal. The portal is 450 m (1,476 ft) above sea level and the end of the tunnel is 475 m (1,558 ft) above sea level. Much of the rock through which it has been developed is magnesite with a compressive strength of 150 MPA. The drilling jumbo is an Atlas Copco twin-boom Boomer 282 Raildrill drilling 42- to 45-mm- (1.6- to 1.7-in.-) diameter holes to a maximum length of 2.5 m (8.2 ft), depending on ground conditions. This is a drill jumbo that Skanska has used successfully on a number of projects during its life. The condition of the rock through which this drift has been driven is extremely variable. Five classifications of A1 and A2 and B1, B2 and [ ] B3, where A1 is the most competent rock and B3 is the worst, have been established. The amount of support used, of which more later is determined by the classification of ground conditions. At the time of the author?s visit, the project it was about 40 days ahead of schedule, thanks to high advance rates. For instance 6 m/day (20 ft/d) was the plan for the advance to be achieved in B1 rock, but sometimes the crews have achieved 8 m/day (26 ft/d) ? which is the average for the whole project ? in those conditions. In A1 the best advance rate achieved is 12 m/day (39 ft/d). The loading unit is a Häggloader 9HR-B on crawler tracks with a pony track to run on the rails. This allows the unit to be towed up and down the drift along the rails. To load from the face, the Häggloader lowers the foot of its onboard conveyor system to the floor and the backhoe pushes material on to it. This digging arm-conveyor combination produces uninterrupted, optimal volume loading of the haulage unit, without spill ? a technique offering load capacities as high as 180 m3/h (6,356 cu ft/hour). Further-more, as an electrically powered machine, it offers great

Jan 1, 2009

By S. G. Ozkan

An investigation was carried out into the effect of physical parameters, such as particle size of the sample, residence time, solid/liquid ratio and impeller speed in the flotation cell, on the solubility in soft tap-water of colemanite (calcium-bearing borate) from Emet, in Turkey. Solubility increased steadily with residence time from 5 to 20 min but only minimally thereafter. There was a similar increase with impeller speed from 500 to 1 500 rev/min, beyond which a solubility of around 1.05 g/l was again established. There was a slight decline in solubility as the solid/liquid ratio was increased from 1 to 30%, with stable values around 1.05 g/l at a 20% ratio, while a sharp decrease was observed with decrease in size down to the -20 micrometre fraction. The effect of solubility should be taken into account if the application of a wet-processing method is being considered for the ore, while it can also result in losses of material during handling and storage

Jun 21, 1905

By M. van Schoor

Coal remains South Africa?s most abundant and cheapest source of energy, and there is an ever-increasing necessity for optimal and safe extraction of the remaining reserves. Increasing focus on cost-effective mining and zero harm to the environment and miners has resulted in a shift in attitude towards the application of geophysics in local coal mining and exploration. Furthermore, technological advances have contributed to geophysics being embraced more readily by the coal mining industry, compared to a decade or two ago. Predictably, the growing interest in geophysical technologies has also created a need for education and training in the basic principles and application of geophysical methods, as local coal mining companies generally do not have in-house geophysicists. Consequently, the Coaltech Research Organisation?s Geology and Geophysics working group forum compiled a textbook aimed at addressing this need: to produce a guide for applying geophysics to coal mining problems in South Africa. The target audience for such a book would be coal geologists, mine surveyors, mine planners, and other mining staff with limited or no geophysics background. This paper provides a very brief overview of the book by summarizing key sections and selected examples. In doing so, the value of geophysics to solving a range of coal mining and exploration problems is highlighted.

Jan 1, 2014

By Richards S. M

The abundances and abundance relationships of lead, zinc, copper and silver in the major sulphide lenses at Broken Hill are examined, and their possible geochemical significance discussed.When expressed as atoms per cent, zinc is the most abundant base metal throughout the whole .group of orebodies, the highest average lead: zinc ratio (No. 2 lens) being about 0·45, the lowest (No. 1 lensZinc Lode group) being in the 0·12-0 ·14 range. Lead and silver are clearly higher in the lower two orebodies, but the abundance of zinc shows no apparent relationship with stratigraphical position. Among the base metals copper is conspicuously low and remarkably uniform, a feature noted in other conformable orebodies.Although, as has been recognised for many years, abundances of silver and lead, and lead and zinc, are sympathetically related, correlation within the pairs is variable and generally of low degree. Silver and lead show distinctly the better correlation, particularly in No. 3 lens. On the basis of lead: zinc ratios, No. 2' and No. 3· lenses, on the one hand, and the No. 1 lenses, Rhodonitic and Siliceous Zinc Lodes on the other, constitute two groups. However on the basis of silver : lead ratios, No. 3 lens stands alone, No. 2 lens showing clear affinities with the higher layers. Ternary relationships between copper-zinc-Iead and silver-zinc-Iead emphasize the very close constitutional relationship between the No. 1 lenses and the two "zinc lodes".The possible implications of these relationships are then discussed in the light of the' two principal theories-hydrothermal replacement or chemical sedimentation-held for the formation of the Broken Hill ores. It is pointed out that the ratios of the four metals in the ores are rather different from those found in most igneous and sedimentary rocks, and in seawater. For 'example, whereas copper and zinc are present in almost equal amounts in most terrestrial materials, copper in the ores is only about one-hundredth of the amount of zinc. Lead has increased somewhat, but the ratio of silver to lead has fallen; in spite of its recognition as a source of silver, the Broken Hill lode is impoverished in silver with respect to lead as compared with most common terrestrial materials.No solutions are offered to these prob'lems of abundance. Rather it has been the aim of the work to provide data, and to demonstrate the...

Jan 1, 1961

The Telfer main dome open pit is operated by Newcrest Mining Limited at a current production rate of 50 Mt/a from a pit dimension compromising 2 km strike length, 1 km width and 250 m depth. As part of the refeasibility of the Telfer operation undertaken early this decade, Newcrest identified that an underground sublevel cave (SLC) operation along with an increased scale of open pit would support a new plant targeting the processing of gold and copper ore at 17 Mt/a rates. The SLC was initiated in late 2006 and broke into the open pit in late 2009. This situation is unique across the mining industry where a cave breakthrough was planned and occurred within an active large open pit operation. The SLC broke though into the west side of the Main Dome open pit into a specially prepared bench that was left at the 5384 RL of cut-back stage 3. A main haulage ramp is within 100 m from the edge of the cave breakthrough zone and this ramp passes down to the active levels which are progressing toward the 5200 RL. This paper presents insight into the mine planning and risk management associated with continued operation of the open pit operation while an active SLC breaks through. The cave breakthrough presents unique areas for risk management as there is potential for rapid propagation and subsidence. To support the undertaking, mine design and major hazard management planning has been carried out. Focus areas include; dual ramp system design, preloading the breakthrough area, monitoring of cave propagation and air gap using a seismic system and deep hole extensometers, wall stability and subsidence monitoring using radar and prism systems, and key trigger and response planning.

May 1, 2010

By A. M. Ramalho

In the synthesis and sintering processes to obtain superhard materials, such as diamond and cubic boron nitride, deformable ceramic capsule is used as gasket to transmit and support the required high pressures and high temperatures, HPHT. The ceramics materials for these capsules should have special physics and chemical characteristics such as refractoriness, shear strength and compressibility. In this work, Bridgman?s anvil made of hard metal or speed steel was used to characterize some ceramics materials in terms of their maximum compressible thickness. Tests were also performed with different resin polymers used as binding mixture with ceramics powder. Chemical analyses and investigations through scanning electronic microscopic (SEM), X-ray and real tests for the synthesis of diamond were also performed. The results showed that local Brazilian calcite can be successfully used in the manufacture of HPHT gaskets.

Jan 1, 2006

The past decade has seen revolutionary advances in communications and information-handling techniques which have been stimulated by "cold war" military requirements and by current programmes for probing into outer space. The tools used in exploration for petroleum and minerals have been improved significantly as a result of this new space age technology and even greater improvements are on the way.Two areas of technical activity have been particularly fruitful in enhancing the effectiveness of exploration methods. These are1. the development of new approaches, based on information theory,for extracting signal from noise more efficiently than before, and2. the use of high-speed digital computers for storing and processing all kinds of exploration information, not only geophysical but geological as well.In seismic prospecting, use of information theory has led to new techniques such as time-domain filtering, wave-number filtering and correlation methods which have made it possible to obtain usable reflection data from areas which were previously considered non reflective. Complex playback and other data processing facilities have been developed to apply these approaches.Digitization of geophysical data for handling by high-speed electronic computers facilitates many of these techniques for signal-to-noise improvement. Direct digital recording of seismic data in the field is now being d'one on an experimental basis in the United States, and this should become a standard procedure, at least for problem areas.The increased dynamic range, flexibility of filtering and other data processing, and convenience of information storage and retrieval make digital recording attractive in spite of its high cost compared to conventional analogue methods. Digital computers are being programmed to carry out many operations in data reduction and interpretation with substantial savings in time and cost over conventional procedures.INTROPUCTIONIn the years that have passed since the end of the Second World War, the western world has witnessed a technological revolution which may be as far reaching in its ultimate impqct as the Industrial Revolution of the last century.

Jan 1, 1963

By Peter Cain

In response to the appearance of excessive convergence of bolted gateroads in the front abutment zone of retreating coal faces at Phalen Colliery, staff from the CANMET Cape Breton Coal Research Laboratory in Sydney, N.S. initiated a programme of roof profile measurements in the front abutment zone of longwall headgates. The results of these measurements allowed a characteristic deformation curve to be determined for each headgate, and the early identification of areas showing an unstable deformation trend. These areas were then reinforced with supplementary support. The monitoring programme was adopted and enlarged by the rock mechanics staff of the Cape Breton Development Corporation, and has been continuing for a period of approximately two years. A sufficient quantity of data now exists to be able to make an assessment of the effects of a number of mining parameters on the performance of the gateroad in the front abutment zone. The following paper describes the method of measurement, illustrated by typical results, and goes on to relate variations in rate and patterns of movement to geology, interaction, method of support and pre-mining stresses.

Jan 1, 1996

For its Hellyer project, Aberfoyle sought to establish a high degree of confidence in all aspects of the feasibility study. Accurate capital and operating cost estimates were an integral and essential part of the study. They were crucial to the evaluation of investment returns and competitive cost position. Both the capital and operating cost estimates were based on the comprehensive data available from exploratory mine development, pilot plant operation, detailed engineering design, and Aberfoyle's experience in the area. One of the principal project objectives was to maximise operating productivity and efficiencies and this created capital cost alternatives which needed thorough cost-benefit assessment. The estimated capital cost for construction and development was $90 million, and the project was completed virtually on time for $80 million. The first year's experience indicated that operating costs would settle to well within 10% of the estimates.

Jan 1, 1990

By J. Bootle

Marrow vein deposits will continue to be an important source of valuable minerals. Productivity per manshift is not keeping pace with operating costs. Increased mechanization of stoping operations must be obtained to create greater productivity at a reduced cost per ton. This application of mechanization may be to either present methods or to newly developed concepts. The total mine unit operations will be effected by increased productivity. Two approaches to increasing the mechanization of narrow vein stoping were studied with the intention of increasing stope productivity and decreasing stoping costs. A method of bringing efficient rubber-tired equipment into narrow cut and fill stopes was designed. It proposes to provide stope access by way of a ramp constructed on the stope fill. Impact breaking equipment was studied and specific applications proposed.

Jan 1, 1977

By Agustín Arias

El presente artículo describe brevemente la historia, métodos de explotación, mecanización, energía eléctrica, las plantas de preconcentración y flotación y el consumo de reactivos de la compañía minera Milpo.

Nov 1, 1954

By Christopher J. Bise

INTRODUCTION Perhaps no other area reflects the art as well as the science of mining-engineering design quite as obviously as strata control. This is due to the fact that the design of mining structures is difficult because rock rarely behaves as a homogeneous medium. Further, the original state of stress and the mechanical proper- ties of the in situ rock are somewhat difficult to deter- mine. However, those aspects that are hard to treat mathematically can and have been successfully approached by model studies and in situ measurements. This chapter will review the fundamentals of strata- control design and will provide examples of applications to typical problems. STRESSES AROUND MINE OPENINGS A close examination of Fig. 1 reveals that, prior to mining, stresses exerted in the overburden can be in both the horizontal and vertical directions. In the example problems of Chapter 1, it was shown that the maximum compressive stress (uv) at any depth (D) below the surface can be approximated as follows: [ ] Further, the lateral stress (oh) is related to the maxi- mum compressive stress by utilizing Poisson's ratio (µ): [ ] As soon as a heading is driven, such as the one in the coal seam shown in Fig. 2, the stresses shift to the sides, or abutments, of the opening. Clearly, these compressive stresses around the opening exceed the pre-mining conditions. The problem of designing an underground opening, therefore, is to determine the maximum stresses and to note if they exceed the ultimate strength of the rock. Table 1 lists several rocks with their corresponding strengths. Figs. 3 to 5 depict the boundary stress concentrations around circular, ovaloidal, and rectangular openings. M is the ratio of the horizontal stress to the vertical stress, or as defined above, p/(l-p). This text will concentrate on the state of stress represented by M = 0.33, which corresponds to the condition of no lateral deformation in a rock having a Poisson's ratio of 0.25. For an ovaloid with an opening width-to-height ratio of 2.0 (Fig. 4), the boundary stress concentrations are at their maximum values at the comers of the opening, with values in excess of 3.0. If the depth of overburden is 500 ft, then the maximum boundary tangential stress ([ ] ) of the ovaloid is: [ ]

Jan 1, 1986

By M Kozikowski

The primary purpose of these investigations is to determine dewatering requirements and likely impacts associated with mining operations. Standard aquifer testing techniques were carried out at multiple locations within the Ord Range near Pardoo, Western Australia. Aquifer properties of an oxidised haematite orebody were calculated from test pumping data conducted in five fully penetrating test bores. Hydraulic properties of the Ridley magnetite orebody were calculated based on short term constant rate pumping tests, and packer tests. Packer tests were conducted in undeveloped and uncased exploration holes and diamond core holes. The new data sheds light on the hydrogeological properties of this previously unexplored region of Western Australia.Aquifer testing procedures for each bore included a preliminary step test followed by a constant rate test. Recovery data were collected in each bore over a period of four to six hours. Prior to testing, background water levels and water samples were collected in a network of monitoring and exploration bores to establish baseline water levels, gradients and water quality. Water quality within the bedrock of the Ord Range varies from 2000 to 5500 mg/L TDS whereas water quality within the alluvial sequence of the De Grey River is highly variable (400 to 2500 mg/L TDS), but is predominantly brackish with some water of potable quality which is used to supply Port Hedland. Test pumping supports the conceptual hydrogeological model that consists of a pod like orebody (aquifer) surrounded by low permeability waste rock (BIF), with very weak hydraulic connection to the adjacent alluvial systems. Calculated hydraulic conductivity from test pumping data across Pardoo ranged from 0.01 to 59 m/d, depending on deposit tested.A groundwater model was used to simulate dewatering required in proposed pits and to estimate the impact of dewatering on the surrounding shallow alluvial aquifers. Test pumping and numerical groundwater flow modelling indicate the proposed below water table pits can be successfully dewatered utilising in pit dewatering production bores. Yields from individual dewatering bores will reduce with time due to the reduction in saturated aquifer thickness.Based on the numerical groundwater modelling and field investigations the likely impacts to the adjacent De Grey River alluvial aquifer system (within the Priority 1 De Grey River Water Reserve) resulting from mining and dewatering activities is considered minimal. Recalibration of the groundwater model will be undertaken once several months of dewatering data are available.The aim of this paper is to present a range of aquifer parameters derived through standard aquifer testing techniques for an area previously unexplored in terms of hydrogeological characteristics. It is the goal of the authors to provide this comparison data set for future work in similar geologic media.

Jan 1, 2009

By Jennifer A. Slatnick

Chlorofluorocarbons (CFC's), once universally accepted as ideal compounds for use in cooling and refrigeration, in foam production, and in cleaning electronic components, are being phased out and eventually banned under extensive international agreements because the chlorine in CFC's is thought to deplete the Earth's ozone layer. The industry has responded with the introduction of alternatives in the form of hydrofluorocarbons (HFC's), which contain no chlorine, and with hydrochlorofluorocarbons (HCFC's), which fill an intermediate gap in the replacement of CFC's. As a result of the elimination of chlorine in the HFC's and the reduction of it in the HCFC's, these alternatives contain more fluorine than the CFC's do. Other nonfluorocarbon substitutes, known as not-in-kind alternatives, contain no fluorine at all. As a result, the fluorspar mining industry, which is the source of fluorine in fluorocarbons through intermediate hydrofluoric acid, is being affected. Concern for this impact has led the U.S. Bureau of Mines to employ its capabilities to analyze various scenarios in the evolution of CFC replacements and substitutes to determine their effect on fluorspar mining. This report utilizes a network flow model to examine the effects of proposed replacements for CFC's, in terms of fluorine content, on fluorspar operations worldwide and on hydrofluoric acid plants in North America and Europe.

Jan 1, 1994

By D. B. Felsher

"Lakeshore Gold’s Bell Creek Mill is located in Timmins, Ontario. The mill has been in operation since 2009 and has undergone several small expansions since then. In 2012 - 2013 the first major mill expansion was commissioned raising the mill capacity from 2,000tpd to 3,150tpd. This was done through the installation of a new ROM ore truck dumping facility, jaw crusher, ore storage dome, SAG mill, leach tank, CIL tank, and electrowinning cell. This paper will cover the equipment installed to raise the tonnage as well as the commissioning of the new equipment including problems encountered and how these problems were solved.IntroductionLake Shore Gold acquired the Bell Creek Mill, along with the Bell Creek Mine, from the Porcupine Gold Mines Joint Venture, a joint venture between Goldcorp Canada Ltd. and Kinross Gold Corporation, in December 2007.The Bell Creek mill, which processed ore from the Bell Creek Mine has consistently achieved recoveries of over 95%, is a conventional gold mill circuit, involving crushing and two stage ball mill grinding, gravity and leaching, followed by Carbon-In-Pulp (CIP) process for gold recovery. The facility had been placed on care and maintenance in 2002. At the beginning of 2009, the mill had been refurbished with an initial capacity of 800 tonnes per day and was subsequently refurbished to a capacity of 1,500 tonnes per day near the end of the third quarter of that year. The Mill was then expanded in 2010 to a capacity of 2,000 tonnes per day.In late 2011, the Company commenced a 50% expansion of its milling facility, from a processing capacity of 2,000 tonnes per day to 3,150 tonnes per day. Phase 1 of the expansion, which mainly involved enhancements to the solution circuit (“back end”) and increased the mill’s capacity to 2,500 tonnes per day, was completed at the end of 2012. Commissioning of Phase 2 of the expansion, to a capacity of 3,150 tonnes per day, commenced at the end of July 2013."

Jan 1, 2015

By Tian Sugui

By means of the measurement of the enduring property and microstructure observation, an investigation has been made into the influences of the element Re and TCP phase on the enduring property of the single crystal nickel base superalloys. Results show that the needle-like TCP phase is precipitated along the <110> orientation on {111} planes in Re-containing/free superalloys during the long term aging, the TCP phase is identified as µ phase, and the precipitated µ phase in 4.5%Re alloy is gradually spheroidized during aging. Thereinto, the needle-like µ phase may obviously decrease the enduring lifetimes of the alloys due to the consumption of the refractory elements and the effect of the stress concentration. But the stress concentration is not easily generated in the regions near the spherical-like µ phase, which is a main reason of reducing the enduring lifetime of 4.5%Re alloy to a small extent.

Jan 1, 2010

Paper written on project work carried out in partial fulfilment of B. Eng (Metallurgical Engineering) degree Electrowinning is an attractive method to recover gold from the relatively concentrated aurodicyanide solutions produced by the elution of loaded carbon, provided that the plated gold can be easily removed using high pressure water sprays. In practice, difficulty with the removal of the gold is occasionally experienced and has been correlated with the presence of high concentrations of copper in the eluate. In this work, the influence of copper on the electro-plating of gold was further investigated using a laboratory electrowinning cell with a rotating disc cathode, polarization, and adhesion tests. It was found that the reduction of copper will compete with gold electrowinning at high copper tenors and that the adhesion of the precipitated gold is also increased under these conditions. Keywords: reduction, adhesion, morphology, current efficiency, limiting current.

Jan 1, 2004

Notwithstanding full concurrence with the dictum of a famous scientist that &quot;definitions are the most accursed of all things on the face of the earth,&quot; in view of the considerable confusion which exists in jigging nomenclature, it is considered advisable to commence this paper with the following explanations of the terms which will be used throughout the text.Jig Bed. The whole layer of material lying on top of the jig screen.Ragging. The layer of denser material lying immediately above the jig screen, which is too coarse to pass through this screen and is confined horizontally by the cells of the top grid.Ore Column. The layer of ore pulp between the ragging and the top-water.Top Water. The water, carrying fine material in suspension, which flOiWS over the surface of the jig bed.Hutch Water. The water added to the jig below the screen. (Except for the water discharged with the hutch concentrate, the &quot;hutch-water&quot; eventually becomes &quot;top-water.&quot;)Feed Water. The water in the ore pulp fed to the jig.(This water becomes part of the &quot;top-water.&quot;)Pulsion. The period of the jigging cycle during which the water is moving upwards relative to the particles in the jig bed.

Jan 1, 1937