Search Documents

By Fadeela Saloojee, Frank K. Crundwell

"Pressure leaching is an option for copper recovery from chalcopyrite. Leaching takes place at high temperatures and pressures in the presence of an oxidising agent. This work shows how the performance of pressure leaching circuits may be improved by optimising the configuration of autoclaves and the heat-removal method. The objective was achieved by creating an autoclave model by combining mass balances, energy balances and population balances. A base-case circuit consisting of a single autoclave was chosen, and this base case was compared with options for increasing capacity by adding more autoclaves to the circuit. These capacity–increase options include circuits in which the additional autoclave is added in parallel, in series and in series with thickening between the two autoclaves. The copper extraction, productivity and cooling requirements for these options are compared. The series circuit with inter-stage thickening has the highest extraction and productivity, however, the cooling duty in the first autoclave is high. In addition to comparing circuit options, three options for heat removal were investigated: cooling coils, quench water and flash recycling. The flash-recycle option results in the highest copper extraction, and the quench-water option gives the lowest copper extraction. INTRODUCTION Background Copper sulfide ores and concentrates containing chalcopyrite are typically hard to leach under atmospheric conditions. Smelting of these ores may also be a challenge, due to the inability of smelting processes to handle low-grade ores, as well as impurities such as arsenic and antimony. Alternative hydrometallurgical routes to treating chalcopyrite are therefore required. One option is pressure leaching, which is the focus of this work. In the pressure leaching process, sulfide ores and concentrates are leached in autoclaves at temperatures of 200 to 220°C and a pressure of about 3000 kPa (Schlesinger et al., 2011). An oxidising agent, usually oxygen, is required to oxidise sulfide ions to sulfate ions. The oxidation of sulfur to sulfate is exothermic; consequently, a method of heat removal is necessary in order to maintain the temperature in the autoclave."

Jan 1, 2015

By Fernando Romero Lage

"Crushing and screening theory and application has remained fairly consistent in the last 50 years. The application of such equipment is guided by varied formulaic conventions and rules that due to the entropic nature of the process, remains more an art than a science. The variability of conditions creates an environment in which trial and error becomes the principal means of process balance and control. This paper illustrates some of the theories behind the process, plus other assumptions, postulates, myths and misconceptions that exist within the crushing and screening industry.INTRODUCTIONContinuous material balance calculations are habitually performed in the design of new comminution circuits as well as in the valuation of existing circuits. A continuous material balance calculation is one in which the input rate of material is equal to the output rate for each unit functioning in the circuit. At continuous analysis, there is no accumulation or losses of material within the system, as it is when performing a discrete event analysis.In order to produce viable and manageable mine-to-mill material, whether it is ready to leach or ready to mill, we must reduce the material in a series of stages. The power demand increases as the material size decreases, as it is when folding a piece of paper successively. As with the paper, there is a crushing size limitation that is a consequence of the mineral properties such as work index, moisture, viscoelasticity, etc. Comprehensive knowledge of crushing plants in both the aggregate and the mining industries show that, after three stages of crushing, a particle size distribution originating from a blasted deposit can be reduced from an nominal maximum size of 500 mm to a nominal maximum size of 12 mm. if the last stage of crushing is set in closed circuit, the screen openings will be able to yield a smaller top size.Achieving steady and continuous material balance poses major difficulties as crusher lose their settings, screens blind or peg, and material characteristics change geographically or seasonally. Overloading conditions in crushers and screens are nothing but counterproductive, and the net losses of an unbalanced circuit can be overlooked when mining operators are paying a lot more attention to the evermore complex systems downstream.It is not simply the crushing of the mineral but achieving the right size for the downstream milling process that will yield the maximum amount of energy savings."

Jan 1, 2010

By Fred Delabbio, Sverker Hartwig

As openpit copper operations transition from surface mines to underground, the speed of underground infrastructure construction prior to production is critical for maximizing the value of the project. Typically, the preferred underground bulk mining method is block caving. In preparation for future underground projects, Rio Tinto made the strategic decision to invest in a step-change program that would develop system solutions to reduce the construction time of block caves. The program focused on improving safety and doubling or more the construction speed of both vertical shafts and horizontal infrastructure compared to existing drill-and-blast rates. After an extensive selection process, Rio Tinto selected the Atlas Copco mobile miner machine as one of the concepts to proceed with for construction of horizontal infrastructure for access and footprint. In addition to un-derground drilling and hauling equipment, Atlas Copco?s Robbins mobile miner concept (a previous attempt at horizontal mechanical excavation) completed trials at Mount Isa, Pasminco and Taisei. Rio Tinto selected the new Atlas Copco mobile miner machine concept for a number of reasons including the use of proven technology from the three previous mobile miner machines and other commercial products, as well as the ability to install complete ground support typical with high rock stress conditions at approximately 1,500 to 2,000 m (4,900 to 6,500 ft) depth. Atlas Copco, with support from Rowa, the Swiss company that specializes in back up systems for tunnel boring machines (TBM), is advancing the detail design of the access version of a tunneling system on behalf of Rio Tinto. Because of the different requirements between an excavation system for access tunnels and that for tunnels on the footprint, two different versions of the mobile miner machine technology were envisioned. The access and the footprint versions of the Atlas Copco mobile miner machine share a majority of key technologies and systems. Therefore, it was possible to conduct a performance conformation test using a full-scale version of the access machine that would also mitigate the technical risks for the footprint version. To alleviate confusion, this article focuses on the access version of the Atlas

Jul 1, 2010

By Dale Lens, W. S. (Wayne) Cusitar

"The use of continuous loading and conveying technology for mining is currently practiced in relatively few mining environments and, even in these cases, on a non-exclusive basis. For the most part, and particularly in hard rock mining, appropriate equipment technology has only recently been developed for continuous loaders, mobile low profile crushers and flexible face conveyors. Mining R&D work by Inco Limited has promoted the development and proving of a loader suited to hard rock conditions and capable of sustained loading rates of500 tonnes per hour. Current R&D work at Inco will test the production capabilities of a low profile mobile crusher by CMS/Eagle and a flexible/ mobile face conveyor system by DME. This follows successful production testing of the Belt Bender concepts in potash mining in Saskatchewan and the development of enhanced extensible conveyor equipment features by DME. Numerous applications are seen for variations of the LCC technology in soft rock, hard rock and surface mining environments. Introduction In some respects, this paper is an announcement of new technology which has the potential to bring revolutionary change to the mining industry. It is also the story of technology transfer, in which mining concepts that have developed independently in underground soft rock and hard rock mines and in surface mining operations are being brought together for a common benefit. It is also the story of key developments in equipment technology which 'complete the cycle' of cooperating technical capabilities to enable the revolution to begin. The phrase ""technological revolution"" requires some defmition: an equipment innovation, or invention, or improvement, will only be revolutionary if its use gives rise to a significant new mining practice."

Jan 1, 1987

By Finlayson EJ

New detailed mapping, micropalaeont- ology and isotopic dating have been successful in revising the stratigraphy of Woodlark Island. All Middle to Late Miocene intrusives and volcanic rocks have been assigned to the Okiduse Volcanics. In addition, the results demonstrate that the Tabukui beds and Wonai Hill beds (N9, late Early Miocene to earliest Middle Miocene) are a single unit. Similarly, the Nasai and Suloga Limestones are confirmed as a single stratigraphic unit as they yield similar foraminiferal ages (upper Te, Early Miocene), and both occur in the same stratigraphic position unconformably overlying basement Loluai Volcanics. Radiocarbon dating suggests a latest Pleistocene age for the upper Kiriwina Formation. Extensive Quaternary cover and low relief prevents detailed structural airphoto interpretation. In general, the structure is simple with all units on Woodlark dipping to the northwest a_4 exhibiting prominent local block faulting.

Jan 1, 1991

By Ramona Prillhofer

Salt slag is a waste product produced by the recycling of aluminum. In most European countries (e.g. Austria, Germany) the landfill disposal of this waste is forbidden because the slag contains soluble salts and these represent a potential source of pollution to the surface and groundwater. Additionally, consisting metal and some compounds in the salt slag can react with water and resulting from this, noxious gases are generated. The recovery of useful materials from these wastes is accordingly both environmentally necessary and economically feasible. This study describes a complete recycling-process for the salt slag, which includes a leaching-cristallization-process to obtain the oxidic residue, a pyrometallurgical-step to clear the oxidic residue and finally an extensive characterization of the achieved products. Due to the increasing price of raw materials, the utilization of the oxidic residue into commercial products has been investigated and application possibilities will be discussed.

Jan 1, 2009

By M. B. Fonseca

Risk quantification in grade-tonnage curves is critical for capital investment in mining projects and can be obtained through geostatistical simulations of orebodies. A practical difficulty may arise in multi-element deposits, as the joint modelling of the related attributes using the traditional co-simulation approaches is computationally intensive and may be impractical for use in the industrial environment. This paper presents the construction of risk-integrating grade-tonnage curves for a complex copper deposit in northern Brazil, by jointly simulating its key geochemical attributes of interest: Cu, Fe and K. The joint conditional simulation of these elements is based on Minimum/Maximum Autocorrelation Factors (MAF). MAF is an approach, based on principal components, that spatially decorrelates the variables involved to non-correlated factors. MAF’sspatial decorrelation at any lag distance is the main and critical difference of this approach from the principal component approach attempted in the past. In the MAF approach, the independent factors are individually simulated and back-transformed to the conditional simulations of the correlated deposit attributes that reproduce the cross-correlations of the original variables. Keywords: Joint simulation; mini/max autocorrelation factors; grade-tonnage curves.

Jan 1, 2003

By G. R. Fitterer

In the manufacture of steel by any process the refining period involves the partial elimination of the metalloids carbon, manganese, phosphorus, and silicon, by virtue of their reactions with ferrous oxide. At the end of this refining stage the metal consists chiefly of iron in which small amounts of these materials are dissolved. Unless some deoxidizer is added to the steel at this time, the reaction between carbon and ferrous oxide will continue with such force that it is impossible to form sound steal in the ingot molds. Instead, the product will exhibit a marked porosity due to the formation and trapping of carbon monoxide-the product of the reaction mentioned. However, if deoxidizers are added, steel may be obtained which is dense and free from gas bubbles. At the same time the deoxidation products will remain in the steal as impurities. For example, silicon additions form Si02 or combinations of Si02 and FeO. Additions of manganese form deoxidation products consisting of various proportions of MnO and FeO. It is also quite obvious that simultaneous additions of manganese and silicon will form oxide combinations either in the binary system MnO-SiO2 or in the ternary system FeO-MnO-SiO2. Work at the Pittsburgh Experiment Station of the United States Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board, involved the study of such deoxidizing reactions and their products. In this connection considerable information is necessary concerning FeO, MeO, Si02, and Al 203, and their various combinations. Some of the most needed data are the melting points of all of these materials. At the outset of this work ordinary methods of melting point determinations were found to be inadequate for various reasons, and the procedure finally selected involved the use of the micropyrometer with occasional corroboration by quenching methods, The reasons for this selection, together with a description of the apparatus, are given in the following pages.

Jan 1, 1932

By Hargraves A. J, Smith J. W

Experiments conducted at Tahmoor Colliery, Sydney Basin, have demonstrated the variability in chemical and isotopic composition of seam gases issuing from boreholes in the Bulli seam and desorbing from lump coal from the same source.From this work it appears that an immediate preferential release of methane accompanies the physical disturbance of the coal seam by penetration with development or drilling or by detachment. In addition, both early released methane and carbon dioxide are depleted in 13C relative to later desorbed gases, therefore the analyses of gas samples taken after such events may not reflect the true bulk composition of the undisturbed seam gas in situ. A method for overcoming this problem by taking gas samples at depth in the "steady state" is proposed.

Jan 1, 1987

A Mechanistic Model of Batch Grinding in Ball Mills

Sep 13, 2010

By William H. Langer

Large amounts of limestone fines co-produced during the processing of crushed lime-stone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point sources such as cement manufacturing. AWL reactants are readily available, inexpensive and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid. This reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities to within about 10 km (6 miles) of the coastline. The majority of U.S. coastal power-generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufacturers and research scientists. There is a concern that CO2 generated from human activities is contributing to climatic and environmental changes. Approximately one-third of anthropogenic CO2 emissions come from burning fossil fuels to generate electricity. Each power plant is capable of emitting several million tons of CO2 annually. A variety of other industrial processes, such as cement manufacture, oil refining, and iron and steel production, also emit large amounts of CO2. The level of atmospheric CO2 can be reduced by capturing CO2 from point-source emissions and storing or sequestering it in isolation from the atmosphere (U.S. Department of Energy, 2003). In 1999, G.H. Rau and K. Caldeira proposed a geochemistry-based method that is referred to as accelerated weathering of limestone (AWL) in a paper titled ?Accelerating carbonate dissolution to sequester carbon dioxide in the ocean ? geochemical implications.?

Jan 1, 2009

By Kyle Selga, Christopher J. Greet

"The Pulp Chemistry Monitor (PCM) has been installed and operated in a number of concentrators in Australasia, and has produced some very interesting results. PCM measures the pH, Eh, dissolved oxygen, temperature and oxygen demand of process streams within a concentrator continuously and in real time.In the example presented in the paper the cleaner feed pulp chemistry is measured, and related back to changes in the mineralogy as well as variations in metallurgical response. For example, a decrease in Eh and dissolved oxygen as well as an increase in the oxygen demand. These changes in the pulp chemistry appear to coincide with increases in the feed grades, probably higher pyrite grades. Further, these variations in pulp chemistry and feed mineralogy have a negative impact on the concentrate grade and recovery.The implication is that if the pulp chemistry is monitored it is possible to predict changes in the mineralogy of the system, and from this the metallurgical response. Further, the changes in pulp chemistry can be used in a control system to counter the changes in mineralogy and maintain the metallurgy.IntroductionIt has long been recognized at a fundamental level that the flotation behaviour of sulphide minerals is dependent on the pH and Eh of the system (for example: Tolun and Kitchener, 1964; Woods, 1976). However, measuring pulp chemical parameters within an operating concentrator has had limited attention. Woodcock and Jones (1970a and b) were among the first to actually collect data from operating plants. Jones and Woodcock (1984) identified some of the chemical complexities of flotation pulps, and noted that most concentrators already operate at high levels of metallurgical performance but there was still considerable scope for improvement. These gains would, in part come from more effective chemical control. In the same volume, Healy (1984) discussed metal ion hydrolysis and precipitation, redox chemistry and how the surface chemistry of sulphide minerals can be influence flotation behaviour. The impact of grinding environment on the pulp chemistry and flotation response of a complex polymetallic sulphide ore is discussed by Forssberg and Subrahmanyam (1993). Their work essentially contrasts the pulp chemical and flotation performance of pulps ground with conventional ferrous grinding media to a fully autogenous system. The data suggested that the reduction or removal of iron hydrolysis contamination from the system could have a positive influence on flotation behaviour, and perhaps the first stage of “controlling” the chemistry of the system should be in the grinding circuit. Grano et al (1995) demonstrated that the collection of pulp, solution and surface chemical data could identify weaknesses within a concentrator, and from these data develop, test and implement solutions that improved the process. Greet et al (2006) showed that the pulp chemical trends observed through primary grinding and rougher flotation circuits of most sulphide flotation concentrators are approximately the same. There are differences in the magnitude of various pulp chemical parameters (pH, Eh, dissolved oxygen, temperature and oxygen demand) as a result of variations in the feed mineralogy and processes employed. Further, it was noted the Eh shifted to more reducing values of the ten days measurements were collected, and this change could be traced to an increase in the iron sulphide content of the feed. Metallurgically, this resulted in an increase in nickel recovery through the recovery of nickeliferous iron sulphides, and a decrease in nickel concentrate grade."

Jan 1, 2016

By Scott Thayer, Michael Murphy, Natalie Cope, Gabriel Esterhuizen, Anthony Iannacchione, Tim Miller, Brent Slaker

"The Subtropolis room-and-pillar mine extracts the Vanport Limestone (Allegheny Formation, Pennsylvanian System) near Petersburg, Ohio. Strata instability problems associated with excessive concentrations of lateral stress caused the mine operator to implement a change in layout design. This mining method has been identified as a stress control layout, which has been used by other underground stone mines in the past with varying degrees of success. Practical experience has shown that entry headings advance in the direction of the principal lateral stress, producing lower stress concentrations with better mining conditions. It is important to minimize stress concentrations along the mining front, so an arrow-shaped advance is recommended. This technique advances more developments (headings) in a “good” direction and reduces developments (crosscuts) in a “bad” direction. As is expected, the stress control layout enhances the potential for shear failures in crosscuts. It is, therefore, important to focus crosscut engineering interventions that either: (a) lower stress concentrations (for example, an arched roof) or (b) enhance strength of the strata containing the shears (for example, rock reinforcement). This study focuses on observing strata conditions on a regular basis and monitoring the response of this strata to changing geologic and mining conditions through 3D Dynamic LiDAR scans.INTRODUCTIONProject AimsThe Subtropolis Mine is extracting the Vanport Limestone in northeastern Ohio. Since the start of mining in 2006, ground conditions have been significantly affected by excessive lateral stress condition. In some other mining districts with this hazard, certain mine layouts have been shown to lessen the potential for unstable ground conditions. The term “lessen” is used to state the realization that stress concentrations are not eliminated but instead occur in less frequency and intensity, and their locations can be projected.The stress-control mine layout, specifically for large-opening room-and-pillar stone mines, naturally evolved at mines suffering from excessive lateral stress problems. These mines will typically experiment with methods to mitigate adverse impacts, thus developing best practices for their conditions. These practices have evolved into a basic framework for the stress control mine layout. For example, Jack Parker was able to write about personal experiences at the White Pine Mine in Michigan (Parker, 1966, 1973). Various researchers at the U.S. Bureau of Mines (USBM), the Mine Safety and Health Administration (MSHA), and the National Institute for Occupational Safety and Health (NIOSH) have studied the effectiveness of stress-control mine layouts over a wide range of geologic conditions (Emery, 1964; Mark and Mucho, 1994; Iannacchione et al., 2003). While the stress control layout design approach has proven successful in many categories, it can be difficult to implement. For example, excessive stress conditions in crosscuts can put the ground control focused intervention at odds with ventilation and haulage constraints, thus limiting optimal crosscut size, shape, and location. Therefore, more information on the effectiveness of this approach is needed."

Jan 1, 2019

By Ronald S. Conti

A new U.S. Bureau of Mines 6.8-L ignitability furnace was used to study the thermal autoignitability of dust clouds. This furnace has a quartz window to allow observation of the early stages of the ignition process and to allow measurement of the dust explosion temperature. Thermal ignitability data were obtained for various carbonaceous and metal dust clouds, with particular emphasis on various ranks of coal dusts. One of the reasons for the construction of the new 6.8-L furnace was to evaluate the effect of chamber volume on the measured autoignition temperatures. Therefore, data from the 6.8-L furnace were compared with data measured earlier in a 1.2-L furnace. The conclusion is that the autoignition temperatures measured in the 6.8-L furnace were only slightly lower on average than those from the 1.2-L furnace. These data on the minimum autoignition temperatures of various materials will be useful in analyzing the thermal ignition hazards of dust clouds in the mining industry and other industries that manufacture, process, or use combustible dusts.

Jan 1, 2010

By D. Craig Camp

conditions. The soils included 65 m of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2, 130 meters of soft clay, silt, and sand not exceeding 30standard penetration test SPT blows per 300 mm, and 220 m of rock ranging between an UCS of 400-600 kgf/cm2. The river crossing, utilizing 1778 mm OD x 19 mm wall x600 mm steel casing pipe without intermediate jacking stations, was part of a seven kilometer liquefied natural gas (LNG) transmission line in South Korea. This 440-m, 1,442-ft, river crossing was microtunneled through three different ground conditions and completed in just over three months. The crossing was achieved with an average of 25 m of ground cover and 15 m of water cover. The Kwang Yang River Crossing was part of a 7 km liquefied natural gas pipeline project for POSCO, a Korean steel producer. The microtunneling machine was custom built for this project. The microtunneling machine selected for this project was tooled with 7 button bits and 2 roller bits. None of the cutter bits were replaced during the drive. Inside the machine, before the spoils laden slurry was pump back to the surface, it would pass through an independent cone crusher. The crusher is placed in the slurry flow to make sure that none of the spoils are so large as to stop the return flow of the slurry. An additional requirement was for the inclusion of a compressed air lock. The air lock was required in the event that the cutter tools required replacement. The cutters were back loaded so that the workers would have access to change the cutters in the event of cutter failure or wear out. No intermediate jacking stations were installed for the drive. The soils included 65 meters of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2 with production averaging between 7 and 20 mm/minute. The second zone contained 130 meters of soft clay, silt, and sand not exceeding 30 standard penetration test (SPT) blows per 300 mm with production averaging between 80 and 180 mm/minute. The third zone contained 220 m of rock ranging between an UCS of 400-600 kgf/cm2 with production averaging between 7 and20 mm/minute. The steel casing pipe was 1778 mm OD x 19 mm wall x 6000 mm long. The project profile, see Figure 1, shows the soil conditions. The hand written numbers locate just above the pipeline are the production dates. The circled numbers are the 10 pipe joint increments. The project required 74 pieces of pipe to span the440 m drive. Figure 2 and Figure 3 are the jacking information. Figure 3 is a continuation of the information from Figure 2. The top section of the graph is the jacking force. The jacking

Jan 1, 2001

By A Scott, A C. Torrance

Explosive properties are typically summarised on manufacturers’ technical data sheets. The values most commonly referred to are the density of the explosive, the energy it is expected to release and its velocity of detonation (VOD). This information is provided so that blasting engineers can make a considered selection of the most appropriate product for a particular blasting application. As an example, a lower VOD and energy product is better suited to blasting in soft, weathered material. In contrast, blasting hard, competent material generally requires a higher energy product which is usually characterised by higher VOD and energy.A review of the technical information supplied by manufacturers shows a wide range of methods of reporting both VOD and energy. A meaningful comparison between products from different suppliers is almost impossible to achieve based on these data. For a similar product, one supplier may have a VOD range of 2800–5800 m/s and a relative bulk strength of 1.34 while a corresponding product from another supplier is quoted with a VOD range of 3100–6300 m/s and a relative bulk strength of 192. In the end, the user has to rely on the level of confidence available from their experience using a certain type of explosive in the type of rock to be blasted at that mine.This paper reviews some of the technical and supporting information that is freely available in the literature and attempts to provide some clarity as to what the numbers that are reported actually mean for the end user. An alternative approach to the evaluation of the suitability of a given explosive to blast a given rock mass is proposed.CITATION:Torrance, A C and Scott, A, 2015. What is relative about energy?, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 447–454 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Duties on Lead Imports from Mexico. - On September 15, the President signed Proclamation 4792 suspending concessions formerly granted as of January 1 on red lead imported from Mexico. The Proclamation also increased the duty payable on litharge imported from Mexico from 3% ad valorem to 3.5% ad valorem, effective September 15. Appeal of Lead Standards. - The U.S. Court of Appeals for Washington, D.C., rejected petitions by the Lead Industries Assoc. and St. Joe Minerals Corp. for a review of standards promulgated by EPA and OSHA. The Lead Industries Assoc. reportedly will appeal to the U.S. Supreme Court on the basis of the "benzene" and "cotton dust" decisions. Scheduled implementation of standards will continue during the appeal.

Jan 1, 1980

By M Logsdon, B Johnson, M Fordham

The underground Neves Corvo copper-tin mine in southern Portugal currently disposes of its tailings in a ætraditionalÆ wet tailings impoundment. With the development of new technologies for preparation and transport of thickened tailings or paste, alternative tailings disposal options have become available that provide a more sustainable water management system and a higher degree of environmental protection. In addition, growing European resistance towards subaqueous disposal may well result in mandatory use of dry disposal methods in the near future. Twenty-four tailings disposal alternatives were evaluated through a cost-effective and easily-implementable bench-scale geochemical screening program conducted at site. Since the tailings are pyrite-rich and highly acid generating, particular emphasis was placed on monitoring likely indicators of sulfide oxidation under the various simulated disposal scenarios. Dependent parameters investigated as part of the program included moisture content, use of alkaline additives (lime, cement), use of a bactericide, and agitation. Response parameters included paste pH, specific conductance, and temperature as indicators of oxidation. The testing was carried out for 30 weeks. Results indicate that a number of relationships between the geochemical stability of the samples (ie sulfide oxidation) and sample characteristics can be readily identified. Based on the results of the screening program, a limited number of tailings mixtures have been selected for further long-term testing in field weathering cells to aid in the identification of the optimal mix design for future tailings disposal at the Neves Corvo Mine. This type of testing provides an inexpensive and reliable methodology for semi-quantitative comparison between tailings disposal alternatives, in particular at locations where more rigorous evaluation through long-term, fully replicated testing is not immediately feasible.

Jan 1, 2003

By M. Craig Miller

As the trend continues in the U. S. toward inceased capital investment in longwall mining equipment and wider panels. the risk also increases for gotential financial and production loses due to undetected geologic anomalies. This paper describes how RIM Sm (Radio Imaging Method) is utilized in conjunction with more traditional exploration and interpretive methods to delineate fluvial channels. displacement faults and poor roof conditions in a Southeastern Ohio coal mine

Jan 1, 1990

This paper briefly describes the shaft, including sinking, steel sets and their installation, shaft equipment and winders.INTRODUCTIONThe New Broken Hill Consolidated Ltd. Service Shaft is a vertical concrete-lined circular shaft, 20 ft. in diameter with -steel sets spaced at 12-ft. centres. The diameter of 20 ft. was established as the minimum that would enable the shaft both to house the proposed hoisting and service equipment and to satisfy ventilation requirements as a downcast airway. The 12-ft. set spacing was based on South African practice in similar types of shafts.The shaft extends from the surface to 28 ft. below No. 22 Level, a total depth of 3,194 ft. Sinking was commenced in September 1946, and equipping completed in January 1955. Initially the shaft was sunk and concrete-lined to a depth of 52 ft., using a stiff-legged crane and clam-shell grab for mucking. Operations were suspended at this depth to allow the installation of the steel sinking head-frame, winders and ancillary equipment.Sinking and concreting were recommenced after four months and continued to a depth of 1,035 ft. 6 in., where the shaft connected with a pilot opening. The concrete lining was poured as sinking progressed and was piped from the surface to this depth, after which all concrete was lowered in buckets and discharged through a distributor suspended in the shaft. A cycle of stripping to the pilot opening and concreting was continued until the shaft reached No. 22 Level. From this level the remaining 28 ft. was sunk full size. All plats were cut and concreted as sinking progressed.

Jan 1, 1957