Search Documents

By J. Riccardi

Copper refineries use massive copper castings as moulds into which impure molten copper from the reverberatory furnace is poured to form anodes for further electrolytic refining. To facilitate removal of the copper anodes from the mould and to prolong the life of the mould itself, it is traditional to spray the mould surface prior to each use with a slurry of baryte in water. This slurry application leads to poor housekeeping, operating costs are escalated by the cost of the slurry, and additional problems in the subsequent refining process are experienced due to carry-over of excess undesirable baryte powder. A one-time application of a diffused layer of aluminum to the surface of the copper mould prior to putting the mould into service has been found to provide extended mould life and facilitate anode removal, as well as reducing baryte consumption; thereby reducing operating costs at both the anode manufacturing and refining stages.

Jan 1, 1999

By Patricio F. Mendez

This paper presents a formalism to automate portions of the traditional scaling procedure. This formalism, called here Order of Magnitude Scaling (OMS), captures essential components of the governing equations into a set of matrices and arrays amenable to computer implementation using standard linear algebra tools. This approach is valid and specially useful for large systems of multicoupled equations. The matrix approach proposed enables one to automate operations such as normalization, dominant balance, obtention of characteristic values, and check for self-consistency. Also, automation permits an exhaustive exploration of all possible balances and the discovery of unsuspected scaling laws. As an example, OMS is applied to the analysis of the viscous boundary layer with no external pressure gradient. The obtained scaling laws for boundary layer thickness and transverse velocity are the same as those obtained with traditional scaling, and in addition, a meaningful estimation for pressure variations within the boundary layer is obtained; this last estimation is typically not addressed in the manual analysis.

Jan 1, 2006

By Javier Antoñanzas, Juan Carlos Múgica, Lourdes Yurramendi

The gasification of wastes containing an organic fraction is usually performed at low-medium temperature using different kind of catalysts. The off gas obtained is a mixture of carbon oxides, mainly carbon monoxide, and hydrogen and can be used for different energetic applications. The main problem is the production of tars in the off gas that has to be separated from the valuable gas flow and, finally, treated separately. An interesting alternative is the partial or total treatment of organics at high temperature. In this case, the off gas contains a higher content of hydrogen and elemental carbon as particulate matter. The energetic source to obtain a temperature in the range of 1,000 - 1,200 ºC is obtained by a plasma torch. In order to make de process attractive, an important issue to be considered is to commercialize the carbon obtained for different industrial applications.

Jan 1, 2008

By Martin Brueggemann

The Tyrone copper solution extraction and electrowinning plant was the first such facility built by Phelps Dodge Mining Company in 1984. Over the next 20 years, the aqueous flow rate capacity of the plant has been expanded from the original design of 12,000 gallons per minute (gpm) to 34,000 gpm to meet production goals in the face of declining copper grades in the leach solutions. The ability to process higher aqueous flow rates through existing equipment comes at the expense of increased organic loss through entrainment to raffinate. These losses of organic (diluent and extraction reagents) can account for up to 10 percent of the plant?s total operating costs. With the recent dramatic price increase of petroleum-based products, these operating costs due to losses are sure to increase. This paper will discuss recent improvements at the Tyrone SXEW plant that have resulted in a 40 percent reduction of organic losses. These improvements include picket fence modifications, new fence materials, organic recovery systems, and operational practices within the solution extraction process.

Jan 1, 2006

By Ralph P. Hackl

Bacterial leaching of the Doe Run Company?s cobalt/nickel-containing copper concentrate at low pH (pH 1.0-1.2) and high redox potential (>750 mV vs. SHE) enabled the cobalt and nickel to be preferentially dissolved over copper and iron due to the rapid passivation of the chalcopyrite component. Selective leaching of the cobalt and nickel was achieved with a mesophilic culture comprised mainly of Leptospirillum-like bacteria and Acidithiobacillus thiooxidans. This finding led to the conception of a novel hydrometallurgical process for passivating chalcopyrite and recovering the cobalt and nickel. The bacterial leaching process was tested extensively at the bench and pilot plant scales during 1997-1998. A pilot plant containing four leaching stages processed 30-40 kg/day of chalcopyrite concentrate continuously for 87 days. The cobalt extraction ranged from 75% to 86% during 6- and 8-day retention times respectively, whereas the copper extraction was limited to about 9%

Jan 1, 2003

By Byung-Su Kim

Most electric arc furnace dust (EAFD) treatment processes employ carbon as a reducing agent for the zinc oxide in the EAFD. In the present work, the reduction reaction of zinc oxide with carbon in the present of various additives was studied. The effects of temperature and the additives of calcium carbonate, magnetite, and mill scale on the kinetics of the reduction reaction were measured in the temperature range of 1173 K - 1373 K under nitrogen atmosphere using a weight-loss technique. The mill scale is one of byproducts generated from the steel rolling process. From the experimental results, it was concluded that all three additives accelerates the reaction rate of zinc oxide with carbon, but the effect of addition of calcium carbonate is the highest. It was also found that magnetite, mill scale, and calcium carbonate in the reduction reaction of zinc oxide with carbon promotes the carbon gasification reaction.

Jan 1, 2006

By Michael L. Sorokin

The metallic nickel production by converting of nickel matte is analysed from the thermodynamic point of view using earlier developed thermodynamic models for sulphide, metal and slag phase. Three-suffix Margules equations are used to calculate thermodynamic properties of melts. Potential diagrams of Ni-FeS-OSiO2 system are calculated for various temperatures and Fe to Ni ratios. The diagrams used for consideration about possibilities of the direct one-stage metallic nickel production.

Jan 1, 1995

By Kurt Westerlund

Three. years operating experience of the FLUXFLOW waste heat boiler (WHB) 20.000 nm /h at Boliden Ronnskar Sweden on a TBRC smelting palena (PbS). Operating experience from the Kivset flash WHB 11.900 nm /h at Samim, Porto Vesme, Sardinia, Italy. Conceptual features of the 93.600 nm3 /h FLUXFLOW (WHB) on the Isasmelt smelting in melt furnace for 180.000 t Cu/a at Mount Isa, Australia.

Jan 1, 1992

By M. D. Street

Lead and zinc production commenced in 1966 at Brunswick Smelting using the Imperial Smelting Process. In 1972 the blast furnace was modified to produce lead bullion only which was refined to corroding grade lead using conventional kettle refining techniques. Since 1972 consumption of lead concentrate and production of refined lead has doubled and this paper describes changes to operating and maintenance techniques which have contributed to this improvement. Reference is also made to improved environmental, health and hygiene practices at the smelter.

Jan 1, 1983

By P. Umadevi

In the light of the discovery of the new super-conducting YBa2Cu3O7-x (YBCO), reactions in the Y2O3¬CuO-BaO system at 1300°C was investigated. The search was for any new phase that may be formed in the system at 1300°C (only 950°C reactions are known so far). 35 mixtures of different compositions were prepared and heated at 1300°C. No new phase was obtained. It was found that YBCO is decomposed at this temperature and Y2O3 and BaCO3 are the major components in the solid obtained after firing in air. However, on cooling the melt slowly and annealing at 950°C YBCO reforms. Such reactions on cooling might have implications on processing of the superconductor YBCO for practical applications as well as on its crystal growth by flux method.

Jan 1, 1989

By Victor Bredykhin

The reasons of formation low quality cathode deposits and conditions of the anode passivation in electrorefining of copper silver alloys with increased (more then 5%) silver content in electrolyte, g/l: Cu - 40; H2SO4-50; 150 and 250; T= 401C have been investigated. As it is shown, increased acidity, anodic current density and silver content in anodes favor passivation. The assumption is made that the ingress of silver on cathodeis the most probable reason of growing dendrites on cathode. We have determined that addition of ethylene carbonic acid to electrolyte in the amount of 3,5 ÷ 10 ml/l suppresses the dendrite formation.

Jan 1, 2006

By Y. Mori, K. Kawanaka

The permeability changes during the sintering of the feed for the Imperial Smelting Process (ISP) were investigated using an experimental sintering pot, as well as with a mathematical model. The results obtained were as follows. The blowing resistance in the sintering bed changes as the sintering reaction proceeds. It increases at the beginning of the reaction when the temperature of the bed is still low. Then it decreases as the reaction continues, accompanied by an increase of the bed temperature. The increase of the blowing resistance in the bed during the sintering process mainly occurred in the drying zone, and was comparatively small in the reaction and cooling zones. Based on Erugen's equation, the change of the permeability during sintering is explained by the decrease of the apparent fractional void volume in the drying zone of the bed.

Jan 1, 2000

By Lætitia H. Delmau

SXFIT is the latest in a series of programs developed in our group to model solvent extraction systems of increasing complexity. SXFIT permits the user complete freedom to define the constituents from which the composition of each phase is to be specified in the data and from which all species of a model for a system are assumed to be formed. Activity coefficients in the nonaqueous and aqueous phases, water activity, apparent molar volumes of aqueous species, and solution density needed for the conversion of concentration from the molarity to the molarity scale are all taken into account by the program. Several extraction systems relevant to nuclear-waste treatment were modeled successfully using this program. As an example, the cesium extraction efficiency of the CSSX process chosen by the USDOE for cesium removal from high-level waste stored at the Savannah River Site can be predicted correctly for varying feed composition.

Jan 1, 2003

By O. M. G. Newman

Research into potential applications of spouted bed electrowinning (SBE) in the zinc industry was conducted, in a collaboration between our two organizations. The main system investigated was zinc from acidic sulfate electrolytes. However, SBE can be extended to other electrolytes, or recovery of other elements. Electrolytic tests were carried out at the 0.01 to 0.1 m2 scale. Spouting behaviour has been studied at a larger scale, approaching a size suitable for an industrial unit cell. Much of our work was carried out using a micro-porous separator (Daramic®). However, we have also shown that ion exchange properties can have a controlling effect on the process chemistry, electrochemical efficiency, and plant flowsheet. In initial 0.1 m2 scale electrolytic tests, design and engineering issues for scale-up were identified. We review the major achievements, promising areas for application in the zinc industry, current status, and remaining barriers to development of SBE technology.

Jan 1, 2003

By Hiroshi Nakazawa

An acid mine drainage in abandoned Horobetsu mine in Hokkaido, Japan, contains arsenic and iron ions; total arsenic ca.10ppm, As(III) ca. 8.5ppm, total iron 379ppm, ferrous iron 266ppm, pH1.8. Arsenic occurs mostly as arsenite (As (III)) or arsenate (As (V)) in natural water. As(III) is more difficult to be remove than As(V), and it is necessary to oxidize As(III) to As(V) for effective removal. 5mL of the mine drainage or its filtrate through the membrane filter (pore size 0.45m) were added to arsenite solutions (pH1.8) with the concentration of 5ppm. After the incubation of 30 days, As(III) was oxidized completely with the addition of the mine drainage while the oxidation did not occur with the addition of filtrate, indicating the microbial oxidation of As(III). In this paper, we have investigated the microbial oxidation of As(III) in acid water below pH2.0.

Jan 1, 2006

By Donald R. Sadoway

Fused salt electrolysis is used extensively in the primary extraction of metals (electrowinning), in the refining of metals (electrorefining), and in the formation of coatings (electroplating). In the case of rare earths, fused salt electrolysis competes with nonelectrochemical processes to make the same products. However, fused salt electrolysis has the potential to produce these metals in a variety of technologically useful forms: thin films and epitaxial layers, powders, and a variety of nonequilibrium structures. The theory and practice of fused salt electrolysis as it applies to the extraction, refining and plating of rare earth metals are described. The potential of fused salt electrolysis to synthesize advanced materials containing the rare earth elements is assessed.

Jan 1, 1989

By Kurt Westerlund

The design of the economically most profitable and technically most feasible smelter process gas handing and treatment as an integrated part of the total metallurgical process is discussed and exemplified, with alternative flow sheets including material and energy balances, investment and operating costs. Retrofitting and de-bottlenecking of existing gas handling lines wil1 be described and exemplified. Methods of increasing total gas handling line availability will be described.

Jan 1, 1992

By Florian Kongoli

The overall productivity and efficiency of sulfide smelting plants depends considerably on the productivity and efficiency of each unit furnace operations. Furthermore, the efficiency and productivity of each furnace affects and dictates to a certain degree the process of managing the flow of materials from one unit to another. A furnace with low productivity, several technical problems or high frequency of accidental shut downs can easily become a temporary or a permanent bottle neck in the entire flowsheet and can be the cause for a low productivity and efficiency of the entire plant. As a result, controlling, optimizing and automating the individual furnace operations in order to assure a stable process but at the same time to increase productivity is an indispensable need. In this paper, the authors discuss their recent work in effectively controlling acute industrial furnace problems such as magnetite build-up and accretions, eliminating unnecessary slag foaming, decreasing slag losses etc. as well as the intensification, optimization and automation of a series of furnaces in sulfide smelting through a unique physical process modeling that correctly simulate the industrial furnace operations and avoid guessing and uncertainties. The advantages of this new approach have been discussed.

Jan 1, 2006

By Vinay Kumar, Jae-Chun Lee, Rakesh Kumar, Manis Kumar Jha, Archana Kumari, Pankaj Choubey

Present work is a part of developing novel recycling technique for waste printed circuit boards (PCBs) i.e. the liberation of metals from PCBs by organic swelling followed by the treatment of resin to remove/ recover hazardous soldering materials. In order to recover the hazardous metallic constituent lead from the liberated resin, initially the leaching studies were made using fresh solder containing 63.9% Pb and remaining tin. Experimental results obtained in different conditions viz. time, temperature and acidity showed -97.20% of lead dissolution with 6M HNO3 at solid to liquid (S:L) ratio 1:10 (g/mL) and temperature 90°C in 75 minutes. The result of the studies validated with crushed PCBs shows that almost total lead and tin was leached out with 6M HNO3 and 6M HC1 respectively at S:L ratio 1:10 (g/mL) and temperature 90°C within 50 minutes. The results will be useful for the treatment and safe disposal of PCBs resin.

Jan 1, 2011

By A. H. -J. Siegmund

Since the last survey of lead smelters in 1987, the lead industry has experienced many changes. Technological innovations, in combination with a dramatic shift in the market structure as well as more stringent government regulations, caused major upheavals in many different areas. Therefore, a new survey was performed to review the progress in the technology of lead recovery over the least decade. The newly conducted survey reflects all current phases of the world's primary lead production, from charge preparation to refined metal shipment. It was prepared by sending questionnaires to individual companies, and the detailed statistical data of this survey are presented. In considering the data developed from the survey, it should be recognized that the primary lead industry is at a crossroad where novel technologies will gradually substitute the sinter machine - blast furnace operation in the new millennium.

Jan 1, 2000