Search Documents

By Dao Hong Quang

This paper describes the numerical analysis of some geotechnical factors influencing the application of Longwall Top Coal Caving (LTCC) method. The study was aimed at comparing the differences in stress distribution in the chain pillars of the face ends and caving mechanism of the top coal in LTCC method between the flat and inclined thick coal seams. The outcomes from this analysis will benefit mine planners in designing the location of roadway development in the next longwall panel. In addition, results from the study will extend the understanding of caving mechanism in top coal section when applying the LTCC method (with the direction of the longwall face is down dip, retreating along strike) in inclined coal seams. The results demonstrate a clear effect of dipping factor on cavability of the top coal and on the stress distribution in the chain pillar of the face ends.

Jan 1, 2008

By S. Paul Singh

Rock burst is one of the most serious mining hazards, adversely affecting the safety, economy and productivity of mines. It is a sudden manifestation of the release of strain energy stored in the rock mass. At present, there is no universally accepted method for predicting the timing of the rock burst. However, if the seismically hazardous regions in mines can be identified before they are exposed to mining then precautionary measures can be planned before the work begins. A study was conducted in Sudbury Nickel Belt and an approach has been proposed to identify rock burst prone workings on the basis of (a) Rock properties and bursting indices (b) In-situ approaches (c) Geological features (d) Mining conditions (e) Observations during mining operations (f) Comparison and analogy with previous case histories of bursting. This approach will facilitate the judicious application of the burst control techniques to seismically hazardous areas.

Jan 1, 2008

By Murali M. Gadde

Perimeter mining is a special form of very productive partial extraction method practiced at some mines in the United States. In the Illinois Basin mines where all major coal seams have weak underclay in the immediate floor, experience shows that any long-term ground control issues will arise due to floor failures rather than instability of the coal pillar itself. While there is a significant amount of work done on floor stability associated with regular pillars, no work has been done so far on the stability of perimeter pillars. This paper reports the results of a comprehensive study that was conducted for the first time on floor stability during perimeter mining in the Illinois Basin mines. A special plate template, which mimicked a common perimeter pillar configuration was created to conduct in-situ bearing capacity tests at five mines in three states of the Basin. Additionally, because of the complex shape of pillars created in perimeter mining that defies any closed-form solution, floor bearing capacity was studied using three-dimensional nonlinear numerical modeling. Based on these in-situ and numerical studies, some guidelines are provided for perimeter pillar stability analysis.

Jan 1, 2009

By Paul Singh

Blasting is an integral part of mining activity and is an inherently destructive process. The quality of the rock mass in which an excavation is being driven has a strong influence on the level of dynamic forces to which the rock can be subjected and sustain damage. Though each specific rock mass occurrence is unique, yet there are common rock mass features which influence the outcome of controlled blasting in a similar way. A field study was conducted which involved assessment of blast damage at several operating mines and blasting of small scale models. The effects of block size and strength, joint parameters, ground water, weathering of rocks and rock mass rating on the results of controlled blasting have been investigated and discussed in this study. The influence of number and thickness of weak layers on overbreak control has been discussed in the light of practical data. Critical particle velocity ranges for damage to rock masses with different qualities have been outlined. An approach for the judicious design of perimeter hole pattern and charge concentration has been proposed.

Jan 1, 2007

By Bruce Hebblewhite

This paper recognises the 25th year of the Morgantown International Ground Control in Mining Conference, by offering a twenty five year review of ground control in the Australian mining industry ? primarily in underground coal. The paper provides an overview of the developments in ground control design methodologies, practices and products. It not only summarises what has been done, but attempts to highlight at least some of the major issues, significant developments, controversies and areas of contention, plus some of the continuing gaps in our understanding or capabilities as we go forward into the next 25 years. Some of the issues included are in relation to: the development of the high strength bolt and cable reinforcement practices widely adopted today and the contrast between stiff and soft systems; a focus on local detail, at the expense of understanding regional stability concerns; dramatic improvements in the use of, and systems available for underground geotechnical instrumentation and monitoring; some of the ground control management trends, including occupational health and safety concerns, availability of suitably trained staff and legislative requirements; the opposing approaches of the empiricists versus the numerical modellers ? is there some middle ground?

Jan 1, 2006

By Luis Giraldo

The installation procedure of fully grouted rebar bolts requires that the bolt be pushed through the resin grout until it is fully inserted in the borehole. Resin grout is a highly viscous fluid that is forced to flow through the annulus between the bolt and the borehole as the bolt advances. Variables such as bolt insertion speed, bolt vs. borehole diameter and grout viscosity determine the magnitude of the pressure generated ahead of the bolt tip. Under weak rock conditions, the magnitude of the pressure of bolt insertion is often sufficient to initiate hydraulic fracturing along joints or bedding planes that allow injection of grout into the strata leading to significant loss of bolt encapsulation. The grout pressure front has also been linked to gloving, a bolt installation problem that reduces bolt effectiveness. A series of tests were conducted to characterize the pressure of bolt insertion during bolt installation under various conditions. Analysis of the data shows three distinct stages of pressure build up during bolt installation. Understanding of the mechanisms involved may allow development of strategies for controlling the pressure buildup and its negative impact during roof bolting under weak rock conditions.

Jan 1, 2006

By Wenbing Guo

Strip pillar mining method is one of the most important techniques for mining subsidence control in China. Mining depth is one of the most important factors that affect subsidence in strip pillar mining method. Six numerical simulation models were set up in this paper to simulate surface subsidence of strip pillar mining at different mining depths. The mining depth in these models ranged from 300 to 800 m. The simulated results were compared and analyzed. The results showed that the subsidence factor of strip pillar mining is related to mining depth. While other things being equal, the subsidence factor of strip pillar mining increases logarithmically with increase in mining depth. Their quantitative relationship was established based on the simulated results.

Jan 1, 2007

By Nic Slatalla

Acoustic emission monitoring techniques are a powerful tool for analysing deformation behaviour and fracture characteristics of rock samples under uniaxial loading. Uniaxial compression tests were carried out on three different types of sandstone for a better understanding of acoustic emission response with respect to rock deformation and damage develop-ment. All sandstone samples revealed congruent characteristic acous-tic emission patterns which correlated directly with distinct stress-strain stages. However, the acoustic response and development within the individual stages proved to be entirely different due to variations in their microstructure.

Jan 1, 2008

By John E. Feddock

Retreat mining plays an important role in the coal production within Kentucky and the Appalachian Coal Basin. In Kentucky, the majority of retreat mining is performed in the Eastern coal field. However, since September 2004, Kentucky has suffered four mining fatalities during retreat mining operations, and the coal industry has focused attention on the safety concerns associated with retreat mining practices. The Kentucky Department of Natural Resources (KYDNR) engaged Marshall Miller & Associates, Inc. (MM&A) to conduct a study to ensure that retreat mining is utilizing the best technology currently available and that the current available employee training programs afford maximum safety to miners. MM&A studied 34 coal mines that were conducting active retreat mining operations and represent about one third of all the mines with approved retreat mining plans in Kentucky. This paper summarizes the major research work conducted (Feddock and Ma, 2006) and recommends the practical methods for improving safety during retreat mining operations.

Jan 1, 2006

By Jeffrey Whyatt

Mining coal in deep, gassy strata is difficult, particularly in deep mines of the west. Dynamic failure (bumps, bounces, etc.) is commonplace, particularly where strong sandstone strata are encountered in the overburden. The disaster potential posed by dynamic failure in these mines is examined and found to be significant. Recent trends in MSHA reportable bumping of deep western coal mines have been increasing. Recent clusters of bumps are explored, a number of which have ended badly. The mechanisms of these bumps and their interactions with geologic structures are explored. Significant progress in controlling these hazards depends on a full understanding of their interaction with geologic conditions. It is apparent that not all MSHA reportable bumps have the same mechanism. These reports describe bumping of pillars, rolling of ribs, outbursts of coal, heaving of floor, shaking-induced roof falls, etc. Progress depends on understanding the underlying mechanisms of these events, and then determining which are potentially active at a particular location. Designs and other protective measures can then be adapted and deployed appropriately. Explicit consideration of mechanisms also supports extrapolation beyond experience as design extends into new mine geometries, geologies, mining methods and increasing depth. Finally, the goal should not be only to design hazard out of mines, but also to provide assurance that this, in fact, has occurred. Pursuit of this goal has been taken up by a major NIOSH research project. The centerpiece of this project is development of a Dynamic Failure Control Program to monitor evolution of dynamic failure hazards with changing geologic conditions to assure that control and protective measures are appropriately deployed.

Jan 1, 2008

By Matt Leeming

Several of the underground mines in the UK require a significant number of cable bolts to be installed, remedially, to control worsening roadway conditions. Often the access is limited and the only power source is compressed air. Machines for this duty are generally designed to perform with 100 psi but regularly only half of this is available. This paper seeks to outline the difficulties this situation causes the Rock Bolting Engineer, highlight the technical requirements for a machine of this type to succeed and detail a solution offered by our engineers.

Jan 1, 2007

By D. Minney

The quality of resin used in South African collieries is currently controlled according to South African Bureau of Standards, "SABS-1534:2002". It has however been found that resin which passed the SABS tests failed in underground short encapsulation pull tests. An investigation was therefore conducted to determine the characteristics of resins that are currently being used in collieries. A series of in situ short encapsulated pull tests was conducted to determine the effect of expired resin on support performance. The results showed that the longer the time after the expiry date the poorer the resin performance. A series of resin-torque tests has been performed using Anglo Coal's testing facility. The following parameters were investigated on different resins: Spinning speed, Mixing time, and Setting time. An attempt was also made to develop a new quality control procedure for resin. This procedure enables mining personnel to make sure that the quality of resin can provide the required support performance. The effect of spinning speed on resin performance was also investigated. The results showed the resin gelling times of resin decreases as the spinning speed increases. It is found that over-spinning with slow speed roofbolters may result in decreased bond strengths. It was found that a 30-second resin (10-second spin, 30-second hold) should never be spun more than 20 seconds, even with very slow roofbolters (100 rpm).

Jan 1, 2005

By Scott A. Shapkoff

High strength cable strand supports are predominately used as a supplemental means of ground control in longwall and development operations in the U.S. The advantages of cable strand supports have been documented and include flexibility, strength, and ease of installation. Since the majority of cable supports installed in the U.S. today are partially grouted, and this same segment of supports has no inherent installed tension, the supports are considered currently arbitrarily strictly supplemental and therefore, cannot currently be deemed primary support (in most mining districts). This paper details and discusses two distinctly different configurations and the technical advantages of active partially grouted cable supports for certain primary support applications. The evolution of the designs for both systems is highlighted. Field data illustrates the amount of active load in relationship to installed torque and the affects that component variables have on this load measurement. Roof control patterns using active cable supports are examined as alternatives for combination patterns using primary and supplemental systems. The importance of maintaining consistent installation procedures plays an important role in the level of performance of the system. Economics comparing the installation of active cables with other primary/supplemental patterns is also included.

Jan 1, 2006

By Nic Slatalla

Resin anchored rock bolts are an effective tool to control the deformation of an underground opening because they combine high support capacity with fast installation. However, there are still numerous shortcomings concerning the understanding and interaction of the system bolt-resin-rock. Field and laboratory test series have been conducted for evaluating the load capacity and bond strength of resin grouted rock bolts in different host rocks under axial load. This paper describes that the behavior and shear strength of the system bolt-resin-rock depends on the rock type and discusses a simple correlation between peak shear strength and shear stiffness in the ratio 1:1000 which may moreover be helpful for estimating rock bolt capacity after installation.

Jan 1, 2006

By Kazem Orace, Navid Hosseini, Mehran Gholinejad

"Selection of the optimum support system for underground openings such as tunnels is a complex process. In this paper a new approach, based on a combination of the Analytical Hierarchy Process (AHP) the Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) and the Preference Ranking Organization METHod for Enrichment Evaluations (PROMETHEE), is introduced. For this purpose, the selection process is assumed to be a multi criteria decision-making problem. First different support systems using FLAC3D numerical code, based on technical safety and stability parameters of the tunnel are specified. Then taking economic and performance parameters as the decision criteria by using the combination of Al-IP, TOPSIS, and PROMETHEE the optimum support system is selected. As a real mine case study this approach is used in the main access entry to the C, coal scam of Tabas collieries. Results clearly demonstrate that the proposed support system selection method is more advantageous than other alternatives.INTROD CTIONGenerally, the support system for a tunnel is selected primarily with the aid of design engineers experience. In other words personal judgment instead of intellectual and scientific criteria is mostly the main basis (Oracc. 2005). However since various support systems can be applied in any particular situation, accurate selection of the optimum support method depends on the integration of many technical, economical and performance parameters, and also on the analysis of the intensity of influence by each of the criteria.In this paper an applicable approach for se lection of tunnel support systems based on Multi Attribute Decision Making (MADM) techniques including: Al IP (Orace et al.. 2009a; Saaty, 1980), TOPSIS (Hwang and Yoon, 1981: Yoon and Hwang, 1995), and PROMETHEE (Brans and Vincke. 1985; Brans and Mareschal. 1992) is introduced. As a field study, this approach was applied to tunnel C1 as one of the main entries in the Tabas coal mine which is the major collieries in the central pan of Iran (Hosseini, 2008).Due to the coal seam conditions coal is mined by mechanized longwall mining (Hosseini 2008). This method requires the 58 excavation of several entries some of which will be used for many years and even for the entire life of the mine (Peng, 2006). Therefore the selection of the support system in these entries is·very important in mining design."

Jan 1, 2010

By Dennis Dolinar

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

Jan 1, 2007

By Collin Stewart

Bowie Resources, LLC (Bowie) has been using the Stability Mapping System (SMS) developed by Dr. Keith Heasley, West Virginia University, since 2005. Seven three-entry longwall gateroads, four longwall panels and a five-entry set of mains have been mined in two different seams in areas originally analyzed with the SMS. This paper compares predictions of mining conditions based on the SMS with actual mining conditions. Specific comparisons include longwall and continuous miner (CM) productivity, longwall tailgate response and support and CM roof bolting requirements. The paper also discusses current thoughts at Bowie on the use of different weighting factors for CM development, longwall face conditions and longwall tailgate support requirements.

Jan 1, 2007

By Nikolay Boykov

Subsurface imaging technologies are part of the electromagnetic (EM) geophysical methods. EM technologies such as radio imaging method (RIM), ground penetrating radar (GPR), and drill string radar (DSR) have great application potentials in the mining industry. However, the success for applying the EM methods to subsurface observations is largely dependant on the correct evaluation of the electrical properties (i.e., resistivity and dielectric constant) of the rocks in the domain of interest. The depth of penetration of the EM signal in coal, as well as the electrical contrast between coal and subsurface boundary rocks or anomalies, are critical parameters for any successful radar system. Based on the measured electrical properties of the coal seam, the proper operating frequency of the radar system must be chosen in order to successfully detect features such as the coal-roof rock boundary, dykes, and voids ahead of mining. The electrical properties of the rocks in a coal seam are frequency dependent. Even though there has been a great advancement in the hardware and data processing software in the past twenty years, there have not been many examinations of the high-frequency properties of coal measure rocks. In this paper, the laboratory setups, the testing procedure, and case studies will be presented for a wide spectrum of frequencies for coal measure rock samples collected from various US coal fields. Tests have been conducted to study the different conditions, including moisture content, that affect the EM properties.

Jan 1, 2006

By Thomas A. Bailey

Since the advent of longwall mining, various methods and materials have been used during relocation to control the intrusion of the gob in the shield/panline area. (figure 1) Controlling this gob is critical to ensuring a safe, speedy, and productive longwall move. An uncontrolled gob can cause a number of problems, from increased worker exposure to entrapment of equipment to lost production. With an eye toward worker safety and increased productivity, several different methods have been developed to minimize gob intrusion. This presentation will take a look at the history and development of longwall ?screens? and ?mesh?, from chain-link fencing to high-modulus polyester geogrids. The benefits and advantages of these developments will be defined. Since 1994, longwall coal mines have used polymer geogrids during longwall recovery to control intrusion of gob material into the shield/pan line area. As described by Brandon and Collins (1996) in their paper presented at the 15th Ground Control Conference in Golden, CO., mines had used various forms of support, such as welded wire mesh, chain-link fencing, wooden cribbing, props, and steel cable to accomplish this. These methods worked, but were labor-intensive, slow, and provided varying degrees of gob stoppage. Although a few mines still use chain-ink fencing to control the gob, longwall coal mines have generally settled on polyester geogrids to control gob and roof and these mines have been instrumental in providing input in order to develop and improve these geogrids products. he trend during the past twelve years has been to incorporate stronger grids and to eliminate auxiliary reinforcements, such as steel cables and nylon or polyester webbing. A job that once required heavy steel cables, props, and fencing is now accomplished with strong, lightweight, high-modulus polyester grids. When we discuss high-modulus grids, we refer to the ratio between load and strain, as illustrated in figure 2. These grids are woven or knitted from yarns that have been pre-stressed. When these grids come under load, they pick up the load more quickly. This allows less deformation in, in this case, the mine roof. The same principle applies when these grids are used to control the ribs. With less elongation, the grids will hold rib material tighter, thereby keeping travel ways more open.

Jan 1, 2006

By Vincent Scovazzo

This paper compares the two most common pillar design equations used worldwide by John T. Boyd Company; the Mark-Bieniawski Equation, an empirical approach, and the Wilson Equation, an analytical approach. The equations are compared in two ways; by their stress profiles and by the Mark-Bieniawski Equation stability factor. Contrasting the two equations based on the visual comparison of their stress profiles is straight forward but evaluating their resulting pillar designs is problematic. Complications arise due to the differences between the use and development of stability factors for empirical equations and safety factors for analytical equations. To work around these differences, comparisons are made between the two equations by first calculating pillar sizes using the Wilson Equation and then determining the Mark-Bieniawski Equation stability factor for these pillars. Pillars designed using the Wilson Equation were based on site-specific data from 23 mines located in the Americas and Australia. Comparing sizes of pillars designed by the Wilson Equation to the Mark-Bieniawski Equation; the Wilson Equation pillar sizes were smaller in 77% of the cases, similar in 3%, and larger in 20% of the cases.

Jan 1, 2008