Search Documents

By Thomas M. Barczak

This report examines practical considerations in longwall support selection that have evolved from Bureau of Mines ground control research. The scope of discussion includes trends in support selection, analysis of shield designs, performance testing, and an examination of support and strata interaction theories and their relevance to in situ support loading. Application recommendations are made for two-leg shields. four-leg shields, and chock-shields. Two-leg shields account for 67 pct of the current active longwall installations and are used in a variety of applications. Automated control systems are likely to continue to grow in utilization. The next major change in shield design is likely to be the application of wider supports. The most effective method of performance testing longwall shields is by controlled displacement of the canopy relative to the base. Controlled force application does not control the load transfer through the shield and may not produce maximum loading in all support components. Theories of estimating support capacity based upon a detached roof block that must be maintained in equilibrium by the powered support are being challenged by concepts based upon the equivalent stiffness of the total ground supporting system.

Jan 1, 1990

By Anthony Iannacchione

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width-to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By K. F. Unrug

In the paper a numerical modeling method is used for evaluation of a roof support system, which is commonly used in the US coal industry. The effectiveness of mechanical roof bolting with or without, header boards and steel straps are compared. This analysis takes into account the response of a shaly roof to changing environmental conditions in mines related to the seasonal changes in temperature and humidity of the intake air. Discussed are principles of roof support in coal mines and based on them a critical evaluation of header boards interaction with bolts and roof itself is carried out. Header boards create a soft inclusion within a much more stiffer system comprising bolt-rock. As an alternative to header boards, steel straps are analysed and corresponding results are presented. It is demonstrated that application of steel strap is beneficial from the stand point of stress distribution and maintaining tension on roof bolts. The laboratory investigations and modeling work previously undertaken by the authors, clearly indicate the detrimental effect of header boards on effectiveness of roof bolting. There are significant practical implications of the research considering that header boards are commonly used in mines. This practice has been probably originated from the wooden support used by mining in "pre-bolting era?, and it has stayed with coal mining based on tradition more than principles of engineering design. It is demonstrated that header board$ are detrimental and actually contribute to development of roof problems.

Jan 1, 1989

By Karsten Zimmermann

Surface deformation monitoring is required all over the mining industry. For example oil and gas companies need this information to support exploration and production activities and to detect impacts from surface subsidence of existing hydrocarbon fields. Also opencast mines require large area information of subsidence due to dewatering of the overburden. Because of this, a lot of surface deformations measurements with GPS or traditional geodetic measurement techniques have been conduced during the last decades. This paper presents the actual capabilities to analyze GPS data using the state of the art Bernese GPS Software for GPS post processing. A new way of monitoring subsidence is a combination of GPS and satellite InSAR data. Considering this it is hoped that a combined strategy will permit receiving overall more information by integrating high point density of InSAR and accuracy of GPS. DMT is one of the leading actors on GPS services especially for monitoring surface movements from underground activities e.g. mining, water pumping or oil and gas exploitation. The paper will discuss preferences and problems of this approach on results of a current project of DMT.

Jan 1, 2008

By W. G. Pariseau

A crown pillar cave occurred at the Ropes Mine in December, 1987, that resulted in closure of the mine. Production was resumed soon afterwards with the formulation of a rock mechanics plan designed to address several issues of safety and stability. The plan proved to be successful and shows what can be accomplished in the realm of applied rock mechanics where a cooperative atmosphere exists.

Jan 1, 1989

By Dan Payne

The Crinum mine has recently completed workings in the southern area of the mine. Over the 10 years of longwall production 40 million tonnes have been extracted and the mine has experienced over 40 longwall face, 3 main gateend, and 2 tail gateend roof falls as well as 5 roadway roof falls away from the longwall. Weak roof (less than 10MPa (1450psi) in the bolted horizon) has been the principal roof control issue at the mine. However, weak, highly cleated coal, water inflow from overlying aquifers, some minor structure and a diatreme in the main headings have also contributed to the challenges at the mine. This paper describes the geotechnical experience over the 10 years, the mine?s approach to addressing the issues and the relative success of these approaches.

Jan 1, 2008

By Victor V. Nazimko

Multiple mining generates gob-interaction displacements. They redistribute stress m strata and obey laws of irreversibility thermodynamics. An irreversible state causes inhomogeneity of the stress distribution on the mass. A destressed zone develops along a working panel, and worked out panels are deprived of the destressing. The inhomogeneity is smoothed out during elapsed time.

Jan 1, 1996

By S. J. Jung

A fundamental study of fragment size distribution and characteristics of fracture pattern is presented for the dynamic penetration of a conical bit into coal block. In this paper, damaged zones during crater formation and fragment size distribution were studied. Bit with a sharper tip angle and a smooth body configuration performed better penetration. Results suggest that in coal cutting the trend should be toward the face cleat direction using a sharper angled tip bits which consumes less energy for an optimum range of penetration depths, thus attaining maximum cutting efficiency and reducing fine fragments.

Jan 1, 1989

By K. H. Brandt

A standard planning system for the development of roadways was adopted for German coal mines based on the results of geotechnical and rockmechanical investigations. Its goal is to provide for sufficient support systems under conditions of multiple seam mining at great depth. The report points out the required determination of geotechnical parameters and the basis for achieving a high level of planning reliability and resulting high performance in roadway development and longwall mining. The instrumentation and the planning procedure for selecting the support design most appropriate for the geotechnical conditions are described and demonstrated by examples.

Jan 1, 2004

By F. N. Voskoboyev

The suggested new method for control of geomechanical state of undermined rock mass ensures, as a safety measure for the earth surface protection, the decrease of deformations by 2,5 - 10 times in mining the single seam, and by 1,5 - 5 times - in mining bed series, i. e. approximately within the seam ranges as in the application of full packing with various compressive properties or partial extraction of resources over the area with different coefficients of extraction. It should be noted that this new method has the following advantages o\w rhr. conventional methods: a) the decrease of the packing area and packing works volume by 2 - 4 fold including the operating and productive expenses; b) the elimination of mineral losses due to the increase of extraction coefficient up to 100 5%; c) rock utilization from workings drivage by its placing in the mined - out space. Perspective field of application of this method: disconservation of mineral resources in the left protective pillars of various designation.

Jan 1, 1996

By Tim Ross

Several shear failures were observed in Shaft #1 at the Mountain Coal Company, LLC, West Elk Mine, after mining longwall Panel 23, 1,100 ft to the east of Shaft #1. It was speculated that this shear damage could be related to differential ground movement caused by in situ stress relief from the ?stress shadow? of the caved zone above longwall Panel 23. A numerical study was conducted to assess the possibility of the shaft shear damage being caused by in situ stress relief and the potential for additional damage to Shaft #1 and two other nearby shafts, due to mining nearby longwall Panel 24. Three-dimensional (3D) models were built in FLAC3D to simulate past and future mining near shafts, the estimated local anisotropic and directional horizontal stresses, and the overlying variable surface topography. The numerical analyses indicated that stress relief due to mining Panel 23 caused the shear damage to Shaft #1and that additional damage to Shaft #1 and the other two shafts, would likely result from mining longwall Panel 24. Additional shear damage was documented in Shaft #1 when longwall Panel 24 was mined, confirming the results of the numerical analyses.

Jan 1, 2006

By S. Yamashita

Recently in Japan, unexpected degradation (surface subsidence) at old underground quarry sites, such as 'Ohya-Ishi' (pumice tuff) pit field has often been occurred. At these quarry sites, the excavation was started 20 or 30 years ago with mechanical chain cutter and the Room and Pillar method, and stopped 7 or more years ago. Therefore, a reliable method has been required for an estimation of long term mechanical properties of the rock and for an observation of a stability of rock-pillars or structures. In this study, creep tests under uniaxial compressive load were carried out on the 'Ohya-Ishi', with the aim of estimating the long term stability of the rock. From these results, a creep mechanism of the rock was discussed using the failure mechanism hypothesis proposed by Bieniawski and by others. On this basis, critical time to failure was predicted by the relationship between the logarithm of life time and stress ratio of the sustained axial creep load. Additionally, outline of the monitoring system of AE/MS activity in the field, which have set by the Ohya Aria Consolidate Public Corporation and the others to predict or to prevent the degradation of those residual pillars, is to be reported. Key words : Ohya-ishi, Pumice tuff, Mine pillar, Long term stability, Creep, Critical time

Jan 1, 1996

By Charles Steed

The design of pillars in room and pillar operations is always a compromise between factor of safety and ore recovery. In actively mined and accessed areas the stability of pillars must be sufficient to support the roof, providing safe working conditions for men and equipment, while optimizing ore recovery. As a reserve is mined out, and if conditions are favourable, pillars are often removed to increase recovery. Considerations for pillar removal include value of the ore, the effect on immediate and overall mine stability and the safety of the mining operations as well as the consequence of disruption of overlying strata and surface infrastructure as the support of the pillars are removed. Many parameters influence pillar strength and the contribution of the pillar to ground support. These include seam height, seam depth, seam inclination, room span, quality of rock, time, etc.. Empirical, analytical and numerical modeling methods are commonly used to optimize pillar sizing and placement and predict influence of pillar extraction or reduction on ground stability. Practical examples for pillar design and optimization in low seam gypsum mining operations and optimizing sequencing of pillar extraction in thick seam metal mining operations are outlined.

Jan 1, 2003

By Andreas Hucke

For the roadway design in the German hard coal mining industry, an advanced combined planning system has been applied during the past 20 years. The German mining industry is working with single entry roadways system. After first longwall passage the roadways will be stabilised with side wall building material packages. Later this roadway will be used again for the second retreating longwall. The intention of the implementation of several different design methods for the planning of the roadways is to enhance the reliability of the results. On one hand the planning system uses numerical simulation and physical modelling in addition to analytical and empirical methods. On the other hand in-situ monitoring and analysis during the roadway development will be used to verify and calibrate the numerical and physical models. Especially before the implementation of new support elements in underground, this system is suitable and reasonable because the new support elements will be tested in the physical and numerical simulation prior to cost intensive underground tests. The interaction between the numerical and physical modelling in comparison with underground monitoring and analysis during development and the later use of roadways will be shown with some examples. The first example shows a rock bolted rectangular roadway which will be mined at both sides of the roadway. Different support and roadway building material package systems are investigated under various stress conditions. The results are utilised to optimise the roadway support and the roadway side package systems. The influence of different points in time of the installation of several support elements in a combined arch and bolted roadway is shown as another example. Two different types of support systems are compared within the physical models. These models are used as a base for ongoing numerical analysis and simulation to find out the ideal point of time to assemble the different support elements. The last example handles the influence of slickensides in the roof of arch shaped roadway on their stability. Different slickenside positions and densities are investigated and classified.

Jan 1, 2006

By Takashi Sasaoka

The PT. Adaro Coal Mine targeted in this research is located in South Kalimantan, Indonesia. The coal production of this mine is increasing year, with about 35 M tons of coal produced in 2006. This mine faces many ground control problems, especially instability of the footwall. Large-scale landslides occur often in the footwall; this may be because of weak rock and the effect of footwall rock weathering. Hence, prompt measures must be developed and followed in order to preserve the stability of the footwall and make this mine safe. Additionally, the final pit design is now being reconsidered because of the increasing demand for and high price of coal. With these issues in mind, this paper describes a solution for improving the stability of the footwall and discusses the final pit design based on the results of an on-site investigation and numerical analysis.

Jan 1, 2008

By J. Brasfield

Jim Walter Resources, along with the Rock Mechanics Branch of British Coal and Strata Control Technology Pty. Ltd., is presently studying the yield-stable-yield pillar design in use at the Blue Creek No. 7 Mine located in Brookwood, Alabama. This paper describes the steps taken to determine stresses on the strata surrounding the pre-driven development entries. It also describes the installation and monitoring of stress cells and extensometers used to quantify the stress build-up and strata movement associated with the headgate pass of a longwall panel. The findings of this study will be used to design and predict the performance of a 2 entry yield pillar system in the Parkgate Seam at Welbeck Colliery in the United Kingdom. Stress measurements and strata movement data from No. 7 Mine and Welbeck will be used to develop a computer model that can predict the performance of such a pillar system in British mines. Jim Walter Resources will use this data to study the performance of the present yield-stable-yield pillar system in order to determine if conditions will allow the stable pillar width to be decreased while maintaining current standards of safety and production.

Jan 1, 1994

By Dakota D. Faulkner

Cable bolts have been very effective in mine ground control. Non-tensioned and tensioned cable bolts are now used for both primary and supplemental bolting (Suder, 2001; Mirabile, 2010). In the United States, cable bolts are typically installed in either 1 or 1-3/8 in. (25 or 35 mm) diameter drill holes and, if point anchored only, are utilized with 4 - 5 equivalent feet (1.2 - 1.5 m) of resin. Cable bolts can be tensioned by various methods such as using an expansion shell mounted on the cable or post-tensioned with a hydraulic cable tensioning unit. In recent years there has been a desire to completely encapsulate the cable bolt for corrosion protection. Fully encapsulating a cable bolt with traditional resins can be very difficult. Keystone Mining Services, LLC (KMS) and Jennmar Corporation have developed a new cable bolt that can be fully encapsulated during installation or post-installation with polyurethane (PUR). The Fully-Grouted Cable Bolt (FGCB)* is equipped with a special head that allows the injection of PUR up through the cable bolt head and cable strands, completely encapsulating the cable and filling the drill hole. Although the FGCB was initially developed to fully encapsulate the cable for corrosion protection, it was also found that by modifying the cable bolt head and injection pressure, PUR could be injected into cracks and fissures of the strata to stabilize the roof. This paper details the development of this system and three underground applications under different ground conditions.

Jan 1, 2012

By W. J. Mcgaughey

A crosshole seismic imaging (tomography) experiment has been carried out in an underground mine in order to delineate waste rock within a massive sulphide ore body. Data comprising 1526 travel time measurements were inverted to yield a compressional wave speed image consistent with, and adding to, knowledge of the extent of the waste inclusions. An effective method of resolving travel time discrepancies measured on reversed ray paths is presented.

Jan 1, 1989

By Raymond A. Mazzoni

Over the last twenty years, roof support technology has made numerous advances since the original wedge and slotted bolts of the 1950's. By comparison, the roof supports used today are more complex and specialized than the supports used in the past, providing mines with a varied selection of supports from which to choose. As a result, when problems with supports are encountered, it is more difficult to determine whether it is the result of geological changes, poor installation practices, or malfunctioning supports. Recognizing this problem, MSHA's Roof Control Division of the Pittsburgh Safety and Health Technology Center, has undertaken the task of publishing a guide for trouble¬shooting problems encountered with roof support systems. The purpose of this guide is to provide a logical sequence to resolving the most common problems encountered with roof supports. The objective of this paper is to introduce this guide to the mining industry as well as provide insight into the evolution of the guide from its beginnings as rudimentary charts to its more comprehensive present format as a practical guide for use by the mining commu¬nity.

Jan 1, 1997

By Yi Luo

In dealing with various subsidence cases, accurate predictions of mining induced subsidence are the basis for correct assessment of subsidence influences and subsequent mitigation efforts. There is a good demand for a reliable tool to perform the subsidence predictions and related tasks. A comprehensive and integrated subsidence prediction model, CISPM, developed by the senior authors in the later 1980?s and early 1990?s (Peng and Luo, 1992) is one of such tools. Built on solid mathematical models and calibrated by a large number of collected subsidence cases, CISPM provides a rich set of features needed in subsidence engineering and research works. Its reliability and usefulness have been proven by numerous field applications. This upgrade of CISPM will not only preserve its original features and reliability but also provide some new needed features and a more user-friendly working environment.

Jan 1, 2008