Search Documents

By S. Bhattacharyya

"Coal bearing rocks are low in strength and have geological discontinuities and moisture sensitivity. Roof and rib falls have been a major cause of fatalities in underground coal mines. Mine engineers design ground control plans for regulatory approvals. A number of tools are available from the National Institute for Occupational Safety and Health to design and assess these plans. Quite often there is not enough geotechnical input information available and databases are used. The Appalachian coalfields have extensive scientific studies to provide reliable regional inputs. Coal mines in the western United States and Canada have different geological and geotechnical conditions, and less available data. Use of inappropriate inputs in the tools like Analysis of Retreat Mining Pillar Stability, Analysis of Longwall Pillar Stability, and Analysis of Roof Bolt Systems may result in unsafe designs or over conservative designs. The tools are convenient but thorough understanding of the inputs, calibration with local test results, and operating experience are important for effective designs. The current paper contains examples of difficulties faced during mine planning using the above tools. INTRODUCTION Sedimentary rocks hosting coal are low in strength. Scientific studies have placed the uniaxial compressive strength (UCS), triaxial strength, tensile strength, and shear strength of sandstone, shale, siltstone, and claystone in lower range of strength among engineering materials (1). Coal bearing rocks are most often weakened by the presence of faults, folds, slickensides, bedding planes, fractures, and other geological discontinuities. The host rocks and coal are often moisture sensitive. The geological discontinuities allow water to enter the strata from surface and underground sources. This combination of low strength, structural weakness, and presence of water results in difficult ground control situations for the coal mines. Roof (2) and rib falls have been a major cause of fatalities in the U.S. coal mines. Modern underground coal mines necessitate wide entries to accommodate large production equipment. The gate roads, section entries, and the mains entries of a highly productive coal mine are as wide as twenty feet (6.1 m). The actual intersection width is nearly thirty feet (9.1 m). Adequate ground control is a key to maintain safe production in such mines. Mine engineers and their consultants routinely submit ground control plans to the regulatory authorities. While working out the necessary roof control system the mine engineers are required to demonstrate the adequacy of the proposed system. There are multiple ways to demonstrate this. Some engineers use traditional load calculation approach of roof bolts (3). Some engineers use numerical methods. Yet a large number of professionals resort to a suite of ground control design software offered by National Institute for Occupational Safety and Health (NIOSH) commonly referred to as “NIOSH Ground Control Toolbar.” These software tools are free and easy to download from NIOSH website. The software included in this package are: Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Coal Mine Roof Rating (CMRR), Analysis of Roof Bolt Systems (ARBS), Analysis of Horizontal Stress Effects in Mining (AHSM), Analysis of Multiple Seam Stability (AMSS), Analysis of Retreat Mining Pillar Stability - Highwall Mining (ARMPS-HWM). These tools are relatively simple to install and use in planning and designing coal mines and prospective coal mines. They accept a number of geotechnical inputs which are collected from either an existing mining operation or from exploratory boreholes. In the absence of necessary input parameters, the programs use default values which are drawn from databases of geotechnical properties built by NIOSH."

Jan 1, 2015

The initiation of a panel cave is an extremely important and infrequent event in the life of a large underground caving operation. A new cave was initiated at the Henderson Mine in 1991, 15 years after its first cave had been developed in 1976. The original cave was started after a half billion dollars had been invested in the development of the mine, mill and 23 km haulage system. Many things had changed since 1976, the most significant of these being much lower realizations for molybdenum. In 1976 the high demand for molybdenum and uncertainty of caving characteristics, formed the basis for a very conservative cave initiation sequence with miles of boundary weakening and inspection drifting. In 1991 the highly competitive molybdenum market in conjunction with 15 years of caving experience made for a very different mining climate.

Jan 1, 1994

By Fredy A. Elorrieta Agramonte, Gabriel von Rickenbach, Roberto Luis Fonseca, David Córdova Rojas, Rolando Romero, Rico Brändle

The mine’s economic life is dynamic by nature. Some factors that create this scenario are the need to recognize new exploitation areas, the evolution of the mineral prices and the development of new technologies to access them. The dynamics of mining development, especially in the underground environment, changes significantly as the stages unfold. In many cases the final solution differs greatly with the initial. The frequent presence of new conditions and factors often cause the mine to develop in a quasi-permanent transition stage, which could be characterized by the generation of dynamic micro-seismic events that could cause rockburst damage in some specific areas. Although they may be infrequent, these dynamic events can have an important adverse impact on mine safety and causes serious losses. Also, changes in the production schedule during exploitation could be a big issue if the problem is not effectively addressed. When the transition of the mine to an active micro-seismic environment begins as an unforeseen scenario, it is frequent to use static ground support systems as they are readily available. Traditionally, the support systems used are reinforced shotcrete with a middle layer of Welded Standard Wire Mesh (WSWM) and Chain Link Standard Wire Mesh (CSWM) of reduced gauges, i.e. wires less or equal than 4 mm in diameter. Although, this support system is used to control static instability problems, there is no good reference of its energy absorption capacity under dynamic load conditions, creating uncertainty in the effectiveness of controlling rockburst events. These support systems are analyzed at the present paper, testing the reinforced shotcrete layer with 4 mm diameter of WSWM and CSWN under dynamic load. Additionally, the influence of the use of high tensile strength steel wire in the meshes (HSWM) compared to the previous ones, is analyzed to assess the scope in controlling rockburst events and keeping the safety of underground environment.

Apr 26, 2022

By Ke Yang, Kai Zhang, Xiaolou Chi, Xiangyang Zhang, Yingming Li

Based on the research background of 1303 working face return air roadway in Jinyuan Zhaoxian Mine, Shaanxi Province, a method of determining the reasonable spacing of boreholes is proposed based on the stress transfer degree of coal above and between boreholes, combined with the law of plastic zone and energy evolution by theoretical analysis and numerical simulation. After drilling pressure relief, the average daily energy of microseismic events decreased by 70%, and those with microseismic energy greater than 104 J decreased by 99.2%. The research has a strong guiding significance and research value for determining the reasonable distance of borehole pressure relief.

Jun 25, 2024

By J. R. Riding

In situ solution mining of uranium has environ- mental advantages over conventional mining. The leaching of uranium, however, alters the groundwater quality in the aquifer where the mining occurs. Currently, regulations require that the groundwater be restored to approximately its original condition. This paper, a summary of a study funded by the Bureau of Mines, reviews the state of the art in restoring groundwater quality after in situ uranium leaching. Current restoration practices discussed include disposal of liquid wastes in deep disposal wells and evaporation ponds, producing from all wells during restoration, and recirculating water purified in surface plants. Methods for predicting the effectiveness and cost of current techniques are presented. Possible alternative techniques are also described. Two restoration operations are discussed.

Jan 1, 1979

By H. Dho

The role of sodium silicate in the anionic flotation of a Florida phosphate ore was investigated using laboratory continuous flotation tests, frothability tests and SEM observations. In the absence of sodium silicate, Ca++ promoted the unwanted activation of quartz by forming calcium bearing precipitates. The addition of sodium silicate enhanced the flotation efficiency through: (1) the removal of impurity minerals and calcium-bearing. precipitates from quartz surfaces by dispersion, (2) drier and more persistent froths stabilized by oily droplets containing calcium silicate precipitates, and (3) higher specific flotation rates of phosphate relative to quartz, leading to faster flotation rates and increased selectivity of separation.

Jan 1, 1990

By E. Watkins, S. J. Schatzel, V. Gangrade, K. M. Ajayi, Z. Khademian

Longwall-induced deformations could jeopardize the mechanical integrity of shale gas well casings positioned in the abutment pillar of a longwall mine. The in situ and induced fracture networks surrounding the gas well could provide pathways for gas flow into the mine creating safety concerns. Hence, this study by the National Institute for Occupational Safety and Health (NIOSH) develops a discrete fracture network (DFN) model to characterize the fractures in the overburden based on geomechanical analyses of mining-induced fracture apertures at a study site in southwestern Pennsylvania. The apertures from the geomechanical model are used to develop a stochastic DFN model of the site in fracture flow code (FFC). Multiple realizations of the stochastic DFN model that replicate potential fracture geometries are simulated, and the fracture permeability is compared with field measurements. A maximum field measurement of 5.03 × 10− 12 m2 (5080 mD) and 3.82 × 10− 13 m2 (386 mD) was estimated over the abutment pillar at the Sewickley and Uniontown horizon, respectively. The results show that the average permeabilities from the DFN model agree closely with the field measurements. In addition, the comparison of all the field measurements and 100 DFN realizations show the model is representative of field conditions. These findings provide critical information regarding fracture characteristics in the overburden, which will further be used to predict potential shale gas flow to the mine in the event of a casing breach for an unconventional gas well.

Jun 17, 2022

Reaction kinetics for gold dissolution in acid thiourea solutions were investigated using formamidine disulfide as an oxidant. For the conditions studied it appears that a surface reaction limits the rate of gold dissolution. The rate was found to be first order with respect to thiourea concentration and half order with respect to the concentration of formamidine disulfide; the apparent activation energy for the reaction was 10.40 kcal/mol (43.40 kJ/mol); and the reaction rate was independent of pH for the pH range 1.0 to 3.0.

Jan 1, 1999

By C. I. Basilio

The adsorption of dialkyl di-and mono-thio-phosphinates on gold, silver and gold-silver alloys has been studied in the present work. These reagents, which are selective collectors for sulfide flotation, have been found to improve precious metals recovery from ores. Voltammetric studies have indicated that dithiophosphinate adsorbs on gold at much higher potentials than on silver, while monothiophosphinate adsorbs only on silver. However, both adsorb on gold-silver alloys with the adsorption potential decreasing with increasing silver content. Using FTIR spectroscopic measurements, the surface species formed during the interactions of these collectors have been identified. The results of the electrochemical and spectroscopic measurements have been compared with the contact angle data obtained at controlled potential conditions.

Jan 1, 1992

By William J. Maloney

OVERVIEW Blind drilled shafts are becoming increasingly popular, particularly in the Appalachian coalfields, as a secondary and sometimes primary means of ventilation. The reasons for the rebirth of the blind shaft are mainly due to it's economics, timeliness, safety characteristics and inherent independence from underground operations. Historically blind drilling has been used to a limited degree in hard rock and tunneling ventilation. With the recent advances in cutters, bit design, equipment and lining systems, particularly in the Appalachian coalfields, blind drilled shafts are once again the shaft construction technique of choice to the educated ventilation specialist. [ ] HISTORY OF BLIND DRILLING Blind drilling has it's roots in numerous places, including the Nevada Test site, the coalfields of Appalachia and Germany along with the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin with oilfield drillers entering the industry on a project basis only to "pull in their horns" and return to the oil patch. Shafts completed by oilfield equipment range from the shallow 5' and 6' lined shafts on the Nevada test site to two (2) 10' lined, 730' deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths with the record being a 90" diameter, 6,150' deep shaft being completed in the Aleutian Islands of Alaska in 1969. EQUIPMENT Oilfield equipment is still being used on the Nevada test site but elsewhere specialized blind hole equipment has been developed to enhance the efficiency of particular applications. Where steel liners are required the A-leg derrick with a simple hoist and rotary system is used. The largest user of this type equipment in the world is the former USSR where blind drilling for mine ventilation is the norm. On applications where trip time and cutter changeout are a priority, top drive hydraulic rigs have been developed which are highly automated, efficient and mobile. These rigs are particularly well suited for tunneling applications where shafts are shallow and sites are usually tight.

Jan 1, 1993

By J. Y. Kim

Silver contained in zinc calcines undergoes several phase changes as it proceeds through the leaching circuit of a roast-leach-electrowin zinc plant. In the present study, the flotation response of silver from leach residues prepared under a variety of carefully controlled operating conditions in the pilot plant has been examined. Flotation of neutral leach residue is shown to be technically viable and to merit consideration for those plants without a high acid leach circuit, but having significant silver values in the feed. Residue leach conditions must be kept slightly acidic to promote the formation of Ag2S, (Ag, CU)2S and Ag2S rims on residual unroasted sphalerite, while simultaneously avoiding the hydrolysis of soluble iron which depresses silver recovery and grade. Factors to be considered during integration of a flotation process into an electrolytic zinc plant are discussed.

Jan 1, 1990

By M. R. Moon

The mine fire at Wilberg Mine in 1984 reached the surface resulting in the failure of the vertical ledge forming the roof and entrance for three main intake portals. The fallen material was covered with a concrete cap to seal the air from the mine. As the mine was recovered and ventilation pressure was placed on seals on the perimeter of the fire area, the concrete capped rubble proved ineffective. Due to the steep and rugged terrain and the inaccessibility to the portals from underground, horizontal holes were drilled into the portal entries and three seals were placed remotely. The seals in conjunction with pressure balancing the seals around the perimeter of the fire area resulted -in the control of the mine fire.

Jan 1, 1993

By P. J. Best

Due to its low mine production costs, competitive rail rates and low sulfur content, the Southern Powder River Basin (SPRB) now commands 30 percent of the U.S. utility coal market. In 1996, production exceeded 260 million tons, a growth of 110 million tons since 1989 and 15 million tons over 1995. Continued growth is expected as the second phase of the Clean Air Act Amendments (CAAA) looms. This growth will be the greatest in the southern part of the basin, where coal quality is higher. This article is an overview of supply and demand issues affecting markets for SPRB coal. It reviews the current markets for SPRB coal and addresses future prospects for market expansion.

Jan 1, 1998

By E. M. Frizzell

An ongoing research program at the Spokane Research Center of the U.S. Bureau of Mines is directed toward investigating drilling parameters (thrust, torque, penetration rate, and drill revolutions) during the drilling of roof bolt holes. A system that measures these drilling parameters calculates the specific energy of drilling, and determines drill bit position has been developed by the Bureau and mounted on a roof bolting/drilling machine, through the use of a microcomputer, critical drilling parameters can be immediately interpreted and analyzed. This makes it possible to inform the operator of hazardous roof conditions. Initial results of this program are presented here.

Jan 1, 1990

By Ralph E. Magnuson

The quality of our environment is of great importance to all of us. Today, there is a great public concern about the degradation of our air, land, and water and the resultant slow death of our planet Earth. The miner has always been concerned with his environment. Historically, mining has been a part of the frontier. As a result, the miner has pioneered and developed many parts of the world. In the beginning, he had to hack out a place for his mine, himself, and his family. He was given accolades and praise for his accomplishments. Now, however, he is attacked as a ravager of the landscape. It was and is no different on the Marquette Iron Range in Marquette County, located in the Upper Peninsula of Michigan. Iron ore was discovered in 1845 and mining was begun by 1848. Over nearly 1 ¼ centuries, a total of 379,197,000 tons have been shipped to market. Ports, docks, railroads, and towns all had to be built in order to get that tonnage out to iron and steel makers. In those early days the environment had to be mastered, not pampered.

Jan 1, 1970

By B. Blaschuk

The Freeport McMoRan Bagdad Solvent Extraction (SX) circuit is the oldest plant of its kind currently in operation. The plant was commissioned in 1969 and was the second SX-EW operation to be built following the Ranchers Bluebird solvent extraction and electrowinning (SX-EW) plant near Miami, Arizona. Over the years of operation, the configuration of the SX has gone through many changes to accommodate a variety of pregnant leach solution (PLS) grades and flows. Although modifications to the original plant configuration are numerous, the Bagdad SX circuit has maintained its general form consisting of multiple long and narrow settlers. The unique configuration of the Bagdad SX circuit presents a variety of operational advantages and challenges; however, it continues to operate at a level recognized in the industry as excellent.

Jan 1, 2010

By J. A. Chermak

Piles of sulfide-bearing overburden, ore, and tailings have the potential to generate acid drainage (AD) when exposed to an oxidizing environment. Laboratory column experiments were conducted using acid-generating overburden material with an added surface amendment of limestone and/or lime. Artificial rainwater was introduced and allowed to drain through the columns. Results showed that the limestone and/or lime reacted with the acidic rock, resulting in the precipitation of a hardpan layer of gypsum and amorphous iron oxy-hydroxide at the surface. The hardpan layer significantly reduced the effective permeability of the column. Based on this study, hardpan layers can be created as chemical caps to significantly reduce the infiltration of rainwater and snowmelt into acidic overburden or tailings material. Unlike traditional capping methods (for example, clay and high density polyethylene (HDPE) covers), chemical caps are self-healing.

Jan 1, 1996

By Rameshwar Sah, L. R. Singh, SIVALINGARAJU BARISETTY, SHYAM YADAV, P. K. Ghorui

Fly ash is a by-product generated from combustion of coal in thermal power plant. Disposal of fly ash is a major environmental concern for the power plants. Though a considerable part of fly ash is used in cement making and brick manufacturing, substantial quantity remains unutilized. Silica and alumina are the major constituents in fly ash along with lime. Aluminosilicates and unhydrated lime present in fly ash, in presence of water, undergo a pozzolanic reaction and form cementitious bond which holds the particles together. Bentonite is commonly used as binder in micropelletization of process waste to attain the mechanical strength required for handling and transportation. The bonding of particles by bentonite is a physical mechanism, while fly ash bonding is a chemical mechanism. The present paper deals with the partial replacement of bentonite with fly ash in micropelletization without affecting the quality of micropellets.

Jul 30, 2021

By Brij M. Moudgil

Flotation was introduced in phosphate rock processing in the late twenties and since then it has been an important part of the concentration process. More than two thirds of the rock produced in Florida is upgraded by the flotation process. Since no crushing or milling steps are involved in the material preparation, the flotation plant feed is coarser than in most other mineral flotation systems. During hydraulic processing of the rock, particles in the size range of -14, +150 mesh constitute the flotation feed. This size fraction is further classified by hydraulic sizers, stationary screens and vibrating screens into a coarse (-14, +35 mesh) and a fine (-35, +150 mesh) flotation feed. The flotation techniques for concentrating the fine feed as practiced by the Florida Phosphate producers have been standardized over the years, however, methods for upgrading the coarse feed differ from plant to plant. In this paper an effort has been made to present relative merits of the techniques employed for concentrating the coarse phosphate rock..

Jan 1, 1977

By N. W. Stump

New developments in on-stream analysis using immersed radioisotope gauges including results from plant installations are described. The control of grinding and flotation using a small digital computer has been complemented by this development. A control scheme for grinding which is based on maximum throughput at constant product size and preliminary work in flotation control are also outlined.

Jan 1, 1974