Search Documents

By Gordon B. French, Donald E. Garrett

INTRODUCTION Crude oil reserves in the United States are still very large, even though for many years they have not been sufficient to supply our entire domestic requirements. They are continuously being depleted as oil is pumped from the ground, but new discoveries and improved secondary and tertiary recovery methods are helping to reduce the rate of depletion. It is thus a slowly diminishing resource, but even as it is being consumed, immense reserves of oil are left behind as the so called "un-recoverable" portion of petroleum formations. Most oil fields can only obtain a 15 to 40% recovery of the original reservoir, and it is widely quoted that there are still about 300 billion barrels of this un-recoverable oil still in place (Mauch, 1980, etc.). With the present comparatively high oil prices, and the possibility of even higher future prices and short supply, this oil becomes an interesting potential reserve. Mining the petroleum formation would be one means of recovering at least a portion of this oil. The concept of oil mining is neither new nor limited to conventional oil fields, since the procedure could be equally employed with the otherwise difficult to produce heavy oil deposits, and the solid or semi-solid tar sands and diatomaceous hydrocarbon formations. Estimates place the U.S. tar sand resource at about 30 billion barrels, and heavy oil at 5-10 billion barrels (Unitar, 1982). Figure 1 graphically summarizes the heavy oil reserves based upon formation depth and characteristics, while Figure 2 shows their location. It is apparent that the preponderance of reserves are in California and Texas, but that they also occur in many other states. The major companies engaged in oil recovery from the heavy

Jan 1, 1983

By H. Lowers, P. Hageman, S. Diehl, D. Fey

Understanding relationships between mineralogy, texture, microstructural features, and element distribution and residence in minerals, is critical for accurate modeling of mineral weathering in waste-rock piles. The morphology of minerals and deformation structures, such as veins and faults, are important factors that control: (1) fluid access to the mineral surface to initiate dissolution, (2) the distribution of trace elements, and (3) formation of secondary minerals. We characterized the mineralogy, textures, and chemical properties of waste-rock material at three sites at scales ranging from outcrop to micrometer scale. A comprehensive hand-sample to thin-section scale methodology utilizing light microscopy, scanning electron microscopy, electron microprobe, and laser ablation ICP-MS was used to thoroughly characterize the waste-rock material.

Jan 1, 2007

By Paul D. Tomlingson

Part two of this two-part series covers the use of an integrated information system with administrative information, including error and absentee reports as well as open work files. Part one (ME, July, page 650) discussed conceptualizing and developing a maintenance information system. It explained what information is needed to manage such a system.

Jan 8, 1985

By Georgios Kalamaras, Chiaia Dinu, Platania Paolo, Alessio Carlo, Giampiero Cirvegna, Claudio Santucci

The Project alignment initiates north of Pinerolo, along the State Road 23[S.S. 23] that is one of the principal arteries to the northwestern Alps where a number of Olympic events for the 2006 Winter Games will be held. The 3.5 km ring road bypasses the Porte habitat by traversing twice the Chisone River. It consists of the following principal structures [Figure 1]: San Martino bridge [130 m in four bays] Prarostino viaduct [130 m in four bays] Craviale tunnel [1055 m] Turinella bridge [a 50 m long bridge that connects the two tunnels] Turina tunnel [665 m] Malanaggio viaduct [350 m in 9 bays]. The road section is 13 m wide and is made up of two 3.75 m lanes, a hard shoulder [1.50 m wide] and a 1.25 m wide curb for each lane. The Project maximum velocity is 100 km/h.

Jan 1, 2005

By V. A. Leach, J. R. Johnson

The calculation of the dose to the bronchial epithelium, lungs and other body tissues from exposures to airborne radon and thoron daughters requires a knowledge of the pattern of deposition in the respiratory system and clearance from it. Exposure to radon or thoron daughters is measured in units of Working Level Months (WLM), which is independent of the aerosol particle size, the fraction of daughters that are attached to the aerosol and the degree of disequilibria between the daughters, and age and breathing rate of the subject. These factors will influence the deposition and clearance, and hence dose. It is therefore of interest to find the relationship between WLM and calculated dose as a function of aerosol size, unattached fraction, and disequilibria, and of age and breathing rate, and to define ranges for these parameters for which WLM is an acceptable measure of the risk. This presentation briefly reviews the two dosimetry models being considered by a current Nuclear Energy Agency (OECD) Working Group, and using these models, defines limits on parameters for which the WLM is applicable.

Jan 1, 1981

By Günter Huber, Bruno Mattle, Helmut Westermayr, Daniel Spöndlin, Max John, Nejad Ayaydin

PROJECT DESCRIPTION Alignment The Strenger Tunnel forms part of the S16 four-lane expressway between Landeckand Bludenz. The construction of this important East-West connection started in 1973with the Arlberg Road Tunnel as its key constituent. Beginning in 1992, solutions for the section between Pians and Flirsch were investigated. Efforts to conserve nature and to avoid potential avalanche and landslide areas led to a solution detouring the villages in the Stanz valley. The starting points were predetermind by the intersections at Pians in the East and at Flirsch in the West. As a result of the expected traffic load and the comparatively high gradient of 2.9%, both one-way, two-lane tubes were constructed at once. The north tube is 5.851 m long, the south tube 5.775 m, see Figure 1. Layout of Tunnel Cross-Section The tunnel cross-section was determined by 2 × 3.75 m wide, 4.70 m high roadways, two sidewalks and sufficient space for two fans above the clearance

Jan 1, 2005

By P. M. Prasad

Off-grade molybdenite concentrates, mainly derived from secondary sources as by-products of the processing of copper, uranium and tungsten ores, do not satisfy the purity requirements (percent MoS2) for the production of molybdenum bearing products. This investigation is a continuation of a successful effort to refine a low-grade molybdenite concentrate to prepare a high-grade MoS2 using a mixed acid (HF + HCl) leach procedure. Specifically, this investigation is concerned with an understanding of the separation chemistry underlying the removal of the oxide/silicate gangue and the base-metal sulfide associations present in the low-grade molybdenite by their selective dissolution in the two acids. Experiments were conducted on an off-grade concentrate containing 42.6% Mo. Results of the controlled dissolution tests indicate that both HCl and HF are suitable for the removal of the associated alumina and both work well for iron, nickel and copper. However, HF was found to be the most effective for dissolving silica/silicate and magnesia. An attempt was made to rank the leaching efficiencies of the acids used singly, sequentially or in a mixed mode. Scale-up (300 to 2,000 g) experiments were conducted to validate this approach. Excellent purification of the concentrate was possible by processing the off-grade concentrate with 10% HCl plus 15% HF at 363 K for 7.2 ks in open polypropylene reactors with internal stirring. These conditions leached practically all of the oxide and silicate gangue and 96% of the metallic impurities. Starting from the low-grade molybdenite concentrate (42.6% Mo; 71.1% MoS2) it was found feasible to obtain a refined product containing 97.8% MoS2, which is suitable for industrial use.

Jan 1, 2007

Many states rely upon the Pennsylvania 1957 “Gas Well Pillar Study” to evaluate the coal barrier surrounding gas wells (Commonwealth of Pennsylvania, 1957). The study included 77 gas well failure cases that occurred in the Pittsburgh and Freeport coal seams over a 25-year span. At the time, coal was mined using the room-and-pillar mining method with full or partial pillar recovery, and square or rectangle pillars surrounding the gas wells were left to protect the wells. The study provided guidelines for pillar sizes under different overburden depths up to 700 ft. The 1957 study has also been used to determine gas well pillar sizes in longwall mines since longwall mining began in the 1970s. The original study was developed for room-and-pillar mining and could be applied to gas wells in longwall chain pillars under shallow cover. However, under deep cover, severe deformations in gas wells have occurred in longwall chain pillars. Presently, with a better understanding of coal pillar mechanics, new insight into subsidence movements induced by retreat mining, and advances in numerical modeling, it has become both critically important and feasible to evaluate the adequacy of the 1957 study for longwall gas well pillars. In this paper, the data from the 1957 study is analyzed from a new perspective by considering various factors, including overburden depth, failure location, failure time, pillar safety factor (SF), and floor pressure. The pillar SF and floor pressure are calculated by considering abutment pressure induced by full pillar recovery. A statistical analysis is performed to find correlations between various factors and helps identify the most significant factors for the stability of gas wells influenced by retreat mining. Through analyzing the data from the 1957 study, the guidelines for gas well pillars in the 1957 study are evaluated for their adequacy for room-and-pillar mining and their applicability to longwall mining. Numerical modeling is used to model the stability of gas wells by quantifying the mining-induced stresses in gas well casings. Results of this study indicate that the guidelines in the 1957 study may be appropriate for pillars protecting conventional gas wells in both room-and-pillar mining and longwall mining under overburden depths up to 700 ft but may not be sufficient for protective pillars under deep cover. The current evaluation of the 1957 study provides not only insights about potential gas well failures caused by retreat mining but also implications for what critical considerations should be considered to protect gas wells in longwall mining.

Jul 28, 2020

Development of a permanent human base on the Moon for exploration requires a self sustaining system. This entails production and processing of limited amounts of raw material on the Moon. Any mining and construction activities on the Moon can only be performed by a robust excavation machine that can excavate a variety of material from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, limited amount of information on lunar regolith is available to develop and optimize a machine for given lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe PA A. This paper discusses the results of initial material characterization as well as full scale tests of a prototype cutterhead inrelevent material. A brief review of anticipated production rates under various assumed ground conditions will also be presented.

Jan 1, 2009

By A. Martin

Detailed porewater profiles of arsenic and other interstitial metabolites were used to assess the relationship between trophic status, sediment redox chemistry and arsenic mobility in a historic tailings repository. The results demonstrate that in eutrophied systems which exhibit greater sediment oxygen demand, the depth of the Fe(III) redoxcline, and hence depth of arsenic release, may lie in close proximity to the sediment-water interface. As a result, arsenic scavenging mechanisms are significantly reduced, resulting in a greater flux of arsenic to the water column. Such considerations have important implications for the management of pit lakes, tailings ponds and contaminated lakes which may consider: 1) the discharge of sewage to the water body during operations; and/or 2) post-closure fertilization as a remediation strategy.

Jan 1, 2002

By Hasan Nizamoğlu, Z. Abidin Sarı, Aslıhan Demiraslan, M. Deniz Turan, Tolga Depci

In this study, recovery of copper from solid material (obtained by leaching of chalcopyrite with oxalic acid in the presence of hydrogen peroxide) with a copper oxalate structure was carried out selectively using HCl. The chemical composition of the solid was as 29.3%, 9.7%, and 13.3% for Cu, Fe, and S, respectively. Selective recovery of copper by degrading the copper oxalate structure with a low-solubility product (Ksp = 4.43 × 10−10) was performed by conventional leaching in the presence of HCl. The optimum leaching conditions were determined as 5 M of HCl concentration, 318 K of leaching temperature, 120 min of leaching time, 25 ml/g of liquid–solid ratio and 400 rpm of stirring speed. Under these conditions, approximately 77% of copper and 3% of iron were taken into the solution. According to the characterization of the leach residue that was obtained, the oxalate structure was degraded. Moreover, the results of XRD analysis showed that the sulfur (S) and cubanite (CuFe2S3) phases were mostly observed in leaching residues, and this was supported by the SEM-EDX data. Based on the results, it may be stated that selective copper extraction can be obtained from a chalcopyrite concentrate by a two-step leaching method using a conventional hydrometallurgical technique.

Several economic factors have caused the surface mining industry to require large-capacity shovels and trucks for efficient, high-production, low-cost operations. Some of those factors include technological advancements in equipment, commodity market depressions, increased labor and maintenance costs, contractural obligations and harsh operating conditions. The difficult operating conditions in surface mines, however, pose challenges to the use of high-capacity equipment. They include space limitations, weak over-burden, and weathered soils and rocks. So mining companies face major challenges in selecting appropriate shovels to meet the technical, operating, safety, environmental and economic requirements of their mines.

Jan 1, 2003

By Andrew J. Petruska, Rik Banerjee

This study explores implementing a machine learningbased system to generate a 3D surface repre- sentation of the roof and support straps in the mine. Event cameras have been chosen for their performance in high-dynamic-range lighting conditions and for their low latency. To enable automated drilling and bolting, 3D vision using eventbased cameras has been developed. A ground-truth set is created using two, time-synced event cameras and a LiDAR camera. These sensors are used to construct a ground-truth dataset of corresponding event- camera images and surface maps from the LiDAR. The network is tested with stereopairs of event images and produces a depth image with ±5 mm RMS error on average across 1000 test images.

Feb 1, 2024

By Douglas Beahm

Energy Metals Corp. (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin. The JAB property is one of several potential properties being planned for development as a satellite facility to the greater Antelope uranium project. A National Instrument 43-101 Technical Report was completed for the JAB property. This report estimated total measured and indicated mineral resources on the property totaling 1.6 kt (3,555,022 lbs) U3O8 contained in 2.2 Mt (2.4 million st) at an average grade of 0.073 percent U3O8 at a 0.25 grade times thickness (GT) cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB property is located in Sections 13, 14, 15, 16, 21, 22 and 23, Township 26 North, Range 94 West, approximately Latitude 42° 14’ North and Longitude 108° 00’ West (Fig. 1). This property consists of unpatented mining lode claims and Wyoming state mineral leases com-prising approximately 850 hm2 (2,100 acres).

Jan 1, 2007

By Yousef Ghorbani, Jafar Abdolahi Sharif, Fatemeh Kazemi, Ataallah Bahrami

Kinetic models are the most important tool for predicting and evaluating the performance of flotation circuits. Gilsonite is a natural fossil resource similar to an oil asphalt, high in asphaltenes. Here, in order to determine the kinetic order and flotation rate of a gilsonite sample, flotation experiments were carried out in both rougher and cleaner stages. Experiments were conducted using the combinations of oil–MIBC and gas oil–pine oil, with one test without collector and frother. Five kinetic models were applied to the data obtained from the flotation tests using MATLAB software. Statistical analysis showed that the results of the experiment with oil–MIBC were highly in compliance with all models. Kinetic constants (k) were calculated as 0.1548 (s−1 ) and 0.0450 (s−1 ) for rougher and cleaner stages, respectively. Rougher and cleaner tests without collector and frother also matched all models well (R2 > 0.98), with k values of 0.2163 (s−1 ) and 0.284 (s−1 ), respectively. The relationship between flotation rate constant, maximum combustible recovery, and particle size showed that the maximum flotation combustible recovery and flotation rate were obtained in the size range of −250 + 106 μm in the rougher and cleaner stages. The combustible recovery and flotation rate were higher in the rougher flotation process than in the cleaner stage.

By Yousef Ghorbani, Jafar Abdolahi Sharif, Fatemeh Kazemi, Ataallah Bahrami

Kinetic models are the most important tool for predicting and evaluating the performance of flotation circuits. Gilsonite is a natural fossil resource similar to an oil asphalt, high in asphaltenes. Here, in order to determine the kinetic order and flotation rate of a gilsonite sample, flotation experiments were carried out in both rougher and cleaner stages. Experiments were conducted using the combinations of oil–MIBC and gas oil–pine oil, with one test without collector and frother. Five kinetic models were applied to the data obtained from the flotation tests using MATLAB software. Statistical analysis showed that the results of the experiment with oil–MIBC were highly in compliance with all models. Kinetic constants (k) were calculated as 0.1548 (s−1 ) and 0.0450 (s−1 ) for rougher and cleaner stages, respectively. Rougher and cleaner tests without collector and frother also matched all models well (R2 > 0.98), with k values of 0.2163 (s−1 ) and 0.284 (s−1 ), respectively. The relationship between flotation rate constant, maximum combustible recovery, and particle size showed that the maximum flotation combustible recovery and flotation rate were obtained in the size range of −250 + 106 μm in the rougher and cleaner stages. The combustible recovery and flotation rate were higher in the rougher flotation process than in the cleaner stage.

By A. Adu-Acheampong

Stope instability at Ashanti Goldfields Company Ltd. (AGC) is a major concern. Using information from field mapping, major discontinuity sets were defined, Rock Quality Designation (RQD) was determined. The stability of wedges in the stope walls was assessed using the commercially available computer program UNWEDGE(Rock Science, 1992). Analytical results indicate that the presence of graphite infilling in joints contributes to instability, while steeply dipping joints control wedge slabbing and wedge toppling in the hanging wall. Stable stope widths and dimensions were determined to range from8.1 to 30 meters (m).

Jan 1, 2003

By R. W. Fedors, S. T. Green, R. A. Hart, D. B. Walter

Computational fluid dynamic (CFD) modeling of a potential nuclear waste repository drift may be an important tool to estimate moisture redistribution caused by natural convection within the drift. To refine and support CFD techniques, a small laboratory cold-trap experiment was developed. Results from numerical modeling of the laboratory experiment show the sensitivity of the bulk air flow rate and average air temperature within the drift to several key parameters, including various boundary condition assumptions and surrounding porous media properties.

Jan 1, 2004

By Y. C. Kim, I. S. Roditis, P. K. Medhi

P. Mousset-Jones I found the article most interesting and timely. I consider it imperative that mine case studies like this one are undertaken and published so that the practicing mining engineer and geologist can obtain a better idea of what is the preferred estimation and grade control technique to use, given the site-specific geology, grade distribution, etc. Mining companies, with operating gold mines, need to be encouraged to either initiate such a study in-house or support a research project by financing a graduate student at a local university. The latter method is preferable since it not only provides research support but also an excellent training opportunity for young mining engineers and geologists. Ideally, what is needed is exploration drill-hole, blasthole, and mine production data that can then be used to assess the efficiency of different estimation and grade control methods by comparing the results obtained using the drill/blasthole data with the actual production data. It is hoped that more mining companies will realize that the rewards from this kind of research greatly outweigh the sometimes perceived problem with releasing data to a university. I noticed that the authors used the blasthole data to represent the actual values, the validity of which relies heavily on the two key assumptions with regards to blasthole assays and in-pit ore-waste selection procedures. Could the authors comment in more detail on these assumptions and what criteria they used to check the validity of the assumptions? Since the article was published, have the authors had the opportunity to compare their estimates with the actual production data? It would be interesting to compare other estimation methods with OK and IK. For example, how well did the polygonal method used at the mine compare with the results given in the paper? I would like to mention that B.L. Kwa completed a similar study (Kwa and Mousset-Jones, 1986) using exploration drill-hole, blasthole, and production data from the Alligator Ridge mine in Nevada. The study compared a variety of estimation methods, including IK, and the final results are shown in Fig. 1. The IK method exhibits the smallest difference between estimated and production results and is closely followed by the indicator moving window (Ind MW) method. Reference Kwa, B.L., and Mousset-Jones, P., 1986, "Indicator Kriging Applied to a Gold Deposit in Nevada," Proceedings, Symposium on Ore Reserve Estimation Methods, Models, and Reality, CIMM Annual Meeting, Montreal, Quebec, Canada, May, pp. 185194. Reply by Y.C. Kim We do concur with Professor Mousset-Jones with respect to the merit of such case studies performed at a local university. In answer to his request for comment on the validity of the two key assumptions made in our paper, we can only say that these are reasonable assumptions that are very difficult to validate. The assumption of blasthole assays being accurate can be partially validated by a careful analysis of the nugget component of blasthole variograms. The assumption that the in-pit ore-waste selection procedure in use was an effective one can only be validated through comparison between the mine estimates of ounces of gold versus the actual recovered ounces of gold at the mill. Neither one of these two assumptions has been validated to date due to several reasons. For example, the mine went through a change in management since the study. Similarly, no compelling reasons have been presented to perform detailed variogram analysis of the blasthole data. We do, however, believe that the obtained results (i.e., indicator kriging performs better than OK in a highly skewed deposit) will remain the same in relative terms, regardless of how valid these two assumptions may be. The most recent comparative study by D. S. Lindsey of the Montana College of Mineral Science and Technology also shows a similar ranking between ordinary kriging versus probability kriging, which is an extended version of indicator kriging. Reference Lindsey, D.S., 1987, "A Comparative Study: Probability Kriging vs. Ordinary Kriging at the Golden Sunlight Mine," MS Thesis, Department of Mining Engineering, Montana College of Mineral Science and Technology, Butte, MT, May, 81 pp.

Jan 3, 1988

By J. D. Miller, C. L. Lin

As the techniques and resolution for 3-D spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional x-ray microtomography offers a unique imaging capability. Spatial resolution on the order of ten microns can be achieved with the use of microfocus x-ray generators. Recently, a state-of-the-art cone beam x-ray microtomography system has been installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility has been designed to obtain 2048 x 2048 pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind, instrument will be used to obtain three-dimensional spatial reconstruction for such applications as specific examples 3D liberation analysis, pore structure analysis of particle beds during filtration and air-void system of concrete structures. The utilization of x-ray microtomography not only will allow for quantitative analysis of multiphase systems but also allow for textural characterization and the determination of phase continuity. In this paper, we present information regarding the current use of this new facility and reviewed potential applications for the advanced analytical system.

Jan 1, 2001