Search Documents

By R. J. Bridwell

Acid mine drainage (AMD) occurs in high sulfur coal and heavy metal mining environments. We show remediation methods using 3D numerical ground water flow models and chemical kinetics of pyrite oxidation for acid leaching of pyrite during air and ground water flow. A recently developed numerical model couples air and water flow with kinetics of iron-reactive bacteria, oxygen transport, specific chemical reaction rates, and pyrite oxidation to calculate migration control of pollution. A model is presented which considers diminution of acid mine drainage in pyrite rich ore bodies by raising the potentiometric surface through a vadose zone to reduce acid mine drainage. A ground water model is presented of an initially saturated mountain, containing an adit, with a sloping ground water table. Ground water recharge consists of snowfall and normal precipitation. Simulations indicate that the historically open adit creates a desaturated mountain above the adit. Significant air saturation ranging from 10-90% oxygen can occur to depths of the adit (-270 m). Remediation consists of plugging the adit, which fill s adit and mountain with water from recharge. Plugging the adit required <10 years for resaturation and rise of the water table in the mountain.

Jan 1, 1994

By Jerome A. Westphal

The Middle Mississippi River extends from the mouth of the Ohio River to the mouth of the Missouri River, a distance of about 310 kilometers (km) measured along the river. From its founding in 1764 to the first steamboat arrival in 1817, the City of St. Louis was little more than a trading post. However, with the advent of the shallow-draft steamboat, the Middle Mississippi River rapidly became a major thoroughfare of commerce. In this regard, its importance has been reflected by the development of port facilities at St. Louis and by Federal activity relating to channel maintenance and improvement. First Federal work on the Middle Mississippi River was autho¬rized by Congress in 1824. This work was for snag removal and bank clearing and was directed at reducing the hazards to steamboat traffic, particularly during low-flow periods. During the 1820&apos;s and early 1830&apos;s, the main channel threatened to move toward the Illinois shore and abandon the St. Louis port facilities. In 1836 and 1837, Congress authorized construction of permanent improvements to keep-the river next to St. Louis (Missouri shore). By 1880, it was recognized that bank clearing activities had resulted in a wider and shallower river which exacerbated navigation

Jan 1, 1977

By James A. Decker

Hanna has developed three production planning systems to help the mine engineers determine the sequence of mining from available ore supples. The Production Scheduling System was developed to give the staff a tool for long range planning by sequencing the removal of blocks from an open pit property. It was needed to determine the year of removal for each block so that the optimum present-valued pit limits could be established by our pit design program. Since in this type of planning short term grade control is less of a factor than it is in daily or monthly planning, the system gives the program greater control and more latitude in block selection. It permits only full blocks to be taken.

Jan 1, 1984

By J. Carr

Ring gear and pinions used as the final drive on large metallurgical grinding mills are expected to transmit their rated horsepower reliably for long periods of time. Duty is 24 hrs./ day. Life expectancy of such gear sets is of the order of 20 years; that is, each gear and pinion flank is expected to resist failure by pitting for 10 years. This means that for a dual pinion gear set having a ratio of 18.42:1.0 and a mill speed of 10 RPM, every gear tooth will see 105.12 x 106 surface contact stress cycles and every pinion tooth will see 968.15 x 106 surface contact stress cycles in a 10 year period. The allowable surface contact stress on the gear and pinion is determined by the material hardnesses. The rule being the higher the hardness, the higher the allowable surface contact stress may be.

Jan 1, 1985

By G. Vallebuona

Currently, empirical models are used for predicting the hydrocyclone performance in terms of capacity, cut size (d50,c), water split and partition curve. These models, for example those of Lynch and Plitt, have been developed and checked for hydro cyclones with diameters larger than four inches. For smaller diameter hydrocyclones little empirical modelling has been done. This paper reports extended experimental research on small hydrocyclones. For these cyclones, the suitability of existing empirical models has been checked and their accuracy compared. Modifications of the existing models equations are proposed, improving their predictive capability for the small cyclones performance.

Jan 1, 1994

By Ralph C. Flow

In Cleveland County, North Carolina, one and one-half miles south of Kings Mountain, Foote Mineral Company operates an open pit for the production of spodumene, feldspar, mica, and commercial stone. Spodumene concentrate is sent to Footers Sunbright, Virginia plant and to other customers. Exton, Pennsylvania and New Johnsonville, Tennessee plants produce lithium compounds sold to the oil industry for multipurpose lithium-base greases, to the metal industry as welding flux, to the air conditioning market, and to the glass industry. Ceramic grade spodumene, feldspar, and mica concentrates go to other processing companies from the Kings Mountain plant. Waste amphibolite is delivered to a neighboring quarry operation.

Jan 1, 1962

By Cody Edwards, Ross Webb

5 miles of soft ground tunnel excavation for the SAWS W‑6 project finished months early despite difficult conditions. Success was achieved using TBMs and other equipment built long before most of the crew was even born. The old school means and methods easily adapted to the conditions encountered and were key to the project’s success. Unfortunately, an industry trend is to specify more “advanced” equipment which can sacrifice adaptability or productivity for a perceived reduction in risk. This case history discusses when traditional methods may be the best option.

Dec 1, 2022

By Yohan Cha, Eun-soo Hong, Gye-Chun Cho

"Rapid population growth and scarcity of space have led many developed cities to bury supply facilities. In line with this, utility tunnels have been employed in Korea since the 1970s. However, approximately 70% of structures were installed more than 20 years ago, in response to the issue of ageing, tunnel enlargement has been proposed. The aim of this study is to investigate geo-mechanical behavior due to tunnel enlargement. Tunnel enlargement methods have been researched to suggest a optimal method. A finite element analysis is conducted to evaluate ground behavior by the expansion of internal space. Vertical displacement and settlement trough width are investigated according to ground stiffness and different enlargement size. It was determined that displacement is affected by the enlargement size and ground stiffness. Based on the deformation results obtained from the numerical analysis, it is possible to predict ground behavior and stability upon tunnel enlargement. INTRODUCTION Various infrastructures such as electric lines, communication lines, gas pipes, and water pipes are jointly accommodated by utility tunnels. These utility tunnels improve the aesthetics of urban areas and help ensure stable supply. The first utility tunnel in Korea was adopted in 1978 and new tunnels are still being installed with the development of new suburb cities. Nevertheless, about 70% of the utility tunnels were installed over 20 years ago and they are still being used through ongoing repair. Moreover, 90% of utility tunnels were installed before 1995. With aging of the nation’s utility tunnels various problems such as concrete deterioration and scarcity of capacity have arisen. As solution, reconstruction has been considered. Reconstruction can enlarge space and improve the performance by replacing existing structures. For reconstruction, two routes have been proposed: underground excavation and cut and cover. In order to avoid traffic problems caused by road occupation and civil appeals during construction projects, underground excavation is the more attractive option. Tunnel enlargement methods have been classified (Seo et al., 2008; An et al 2013) and major considerations during tunnel enlargement have been outlined (Beak et al., 2007). Enlargement construction cases on road tunnels around the world were introduced (Kim et al., 2012) and the deformation curve during tunnel expansion was proposed to investigate the range of protection that should be offered (Kim et al., 2008; Beak et al., 2011). However, tunnel enlargement technology is limited to road tunnels and railway tunnels. Hence, a study on shallow box tunnel enlargement is required for practical application."

Jan 1, 2016

By Peter F. Howard

The lower Middle Cambrian phosphorite deposits of the Georgina Basin shown in Figure 1 were found in the period 1966-1968 by three companies, namely, International Minerals and Chemical Corporation, Continental Oil Corporation and Broken Hill South Limited. Of these deposits the significant ones are Duchess, Sherrin Creek, D Tree, Lady Annie, Lady Jane, and Wonarah which together aggregate several billion tons reserves of phosphate. Due to the economic factors of freight costs to the coast and softening of the world market price for rock phosphate, none of them is in production, nor is any in the development stage. This paper reviews the historical background to the discovery of these deposits and then deals principally with the discovery of non-outcropping phosphorites in the Barkly Tablelands of Northern Territory by the interpretation of gamma radiation logs of abandoned water bores.

Jan 1, 1971

By R. Xiong, A. K. Fallaw, G. Wang, L. R. Moore, S. Dobson, J. Gu

"INTRODUCTION The Central District of the Florida phosphate industry is located in southwest Polk and southeast Hillsborough Counties, with the Southern Extension lying in western Hardee, eastern Manatee and northwest De Soto Counties. (Lawver, 1983) Figure 1 shows the major phosphate formations in Florida. Almost all Florida phosphate production has been in the Central district with additional production from a mine in the Northern District. The Central District is comprised of the Bone Valley Deposit, a relatively thin layer of high grade ore which has been the main source of phosphate mining for decades, and the Hawthorn formation, a thick but low grade formation which covers most of peninsular Florida. (Lawver, 1983) Florida phosphate producers use the Crago process where calcium phosphate is floated with anionic, fatty acid type collectors followed by cationic reverse flotation of silica with amine type collectors. The phosphate matrix is put through various size separation techniques to obtain a typical -28 Mesh (< 700 µm) particle size for fine flotation and a -16 mesh (< 1190 µm) to +28 mesh (> 700 µm) particle size for coarse flotation. In some cases this coarse fraction can be sent to shipping as an intermediate product. The +16 mesh (>1190 µm) to – ¾“ (19 mm) fraction is sent to shipping as a final product called pebble. Figure 2 demonstrates a simplified diagram of the mining and processing of calcium phosphate (matrix) through a Central Florida mine. Particle size and mineralogy are important considerations in the Crago process for two main reasons, the mass of the particle and the particle surface area. Both of which are dependent on the coordination of the anionic collector to available Ca2+ sites on the minerals’ surface. The increased surface area, and available Ca2+, of the smaller apatite particles will allow for more fatty acid molecules to coordinate than the larger particles, with a lower availability of Ca2+. So, the larger particle would require more collector to be introduced in the system to sufficiently cover the apatite particles to produce a surface sufficiently hydrophobic to attach to air bubbles allowing flotation to occur. (Guan, 2009) The Bone Valley deposit has very favorable flotation characteristics when compared to other mining ores around the world. The matrix of the Bone Valley is relatively high grade, BPL (Bone Phosphate in Lime) values typically range from 6-18%, BPL recoveries, from such a matrix, can often be achieved above 85+% with fatty acid based collectors dosed below 1 #/ton. As mentioned, the sizing is an important step as there is also high grade apatite in the +16 mesh (1mm) that is screened to a final product grade, 60-65% BPL. The lack of quartz in the larger size fraction has allowed the Central District to produce high quality, low cost phosphate product, called pebble, through effective screening with no further beneficiation. (Guan, 2009)"

Jan 1, 2015

By T. Guler

Turkey has important celestite reserves in Sivas. These reserves have gypsum and/or calcite as gangue minerals. Celestite-calcite ore cannot be concentrated by gravity methods due to the low efficiency of gravity methods in fine sizes. Research was tried to concentrate celestite to a market grade by flotation. Parameters such as pH, particle size, dosage and types of collector and depressant were examined. Cyanamid A-845 and Na-oleate combination as collector, sodium silicate as depressant, and Aerofroth-65 as frother were found as the optimum flotation reagents. By applying 3-stage cleaning, a concentrate assaying 95,34 % SrS04 was obtained with 84,93 % recovery.

Jan 1, 1999

By J. -M. Lopez-Cuesta, C. Petter, B. Otazaghine, M. Batistella, R. Sonnier

"Kaolinite is a dioctahedral aluminosilicate widely used as paper filler and coating pigment. At the best of our knowledge, kaolinite is not widely used in polymer industry. Therefore, in this study, the flame retardant effect of kaolinite in ethylene vinyl acetate copolymer (EVA) and polypropylene (PP) were studied and compared with an alumina trihydrate (ATH) and Talc. Cone calorimeter results shows that the weight percentage of ATH in EVA/ATH composites must be at least 50 wt. % in order to reach an improvement in fire retardancy in terms of pHRR. In the case of EVA/kaolinite, even with 35 wt. % the pHRR is largely reduced. Comparing PP/Talc and PP/kaolinite composites at 30 wt. %, both fillers leads to same reduction in pHRR with a slightly better performance for PP/kaolinite composites. In both cases an intumescent behavior of kaolinite composites was observed that could slow the rate of the rising degradation products, allowing radical recombination reactions. Also, it was observed that kaolinite forms a protective layer on the surface of the samples, which could insulate the material. These behaviors (intumescence and formation of a protective barrier) could reduce the transfer of the degradation products to the flame and explain the better performance of kaolinite composites. INTRODUCTION The use of mineral fillers as fire retardants in polymer matrix are well known and widely studied [1]–[10]. Aluminum and magnesium hydroxides (respectively ATH and MDH) are the most widely used inorganic fire retardants. To achieve fire retardancy with these mineral fillers, about 50-60% loading is required which decrease the physical properties of the composites. The fire behavior of composite EVA has been the subject of many studies [4], [7], [9]–[15]. EVA copolymers are commonly used in the cable industry, due to their high ductility, even at high loading rates. In such applications, the flame retardant systems should be introduced into the polymer to improve the fire reaction. Many flame retardant systems have been tested but the most used industrially relates to formulations based on hydrated mineral fillers (aluminum hydroxide and magnesium hydroxide). Their low cost and reduced fumes generation explains their success. However, to obtain good performance with this type of flame retardants, it is necessary to incorporate high levels (up to 65 wt %), which severely impact other properties such as processability and mechanical behavior. The main modes of action of these flame retardants are the dilution of the gas phase, the endothermic decomposition and a barrier effect created by the inorganic oxide residue which may be improved by the incorporation of other components such as montmorillonites, silicas or talcs."

Jan 1, 2015

By Panagiotis Chryssanthakis

"The aim of this study is to give a better understanding for the performance of the composite material RRS and the synergy effect of its components under different stress regimes and while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. A rather extensive parametric study has been run by using the same key input rock mass parameters and three different in situ stress regimes (sH/sv =2, sH/sv =1 and sH/sv =0.5). Changes have only been made to the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study under each stress regime, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive numerical steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam. The results are varying and are strongly dependent on the imposed stress regime and they show in general the following tendencies: The axial forces on S(fr) show that S(fr) is almost overloaded during the first 4 hours in all 3 stages. More particularly: For the case with sH/sv =2 a) the axial forces on S(fr) and on the steel rebars are reduced after 16 hours and 28 days; b) the same is observed on the shear stresses in S(fr) and on steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged. For the case with sH/sv =1 a) the axial forces on the S(fr) are reduced after 16 hours and 28 days; b) the same is observed for the axial and shear stresses, as well as moments on the steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged."

Jan 1, 2016

By J. M. Dean

The MANpower SUPport Program (MANSUPP), a part of the Mine Management Support System (MMSS), allows an underground coal mine site user to determine manpower requirements for production support work by considering ongoing operations and current mine conditions. The objective of MANSUPP is to plan a detailed manpower structure for a mine by incorporating a production schedule, condition-modified work standards and management preferences to predict required manhours for various activities, for example, belt moves. The program is written in Quattro Pro version 3.0 (Lotus 1-2-3 compatible) utilizing the command language, macro and formula capabilities.

Jan 1, 1992

By M. A. Reyes, L. Yan

"Heat and humidity buildup within refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a life-sustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 hours while maintaining an apparent temperature (AT) below 95°F (35°C). NIOSH tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in NIOSH underground coal mine facilities to investigate the thermal environment over a 96-hour period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners increased over the 96-hour test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating heat and humidity temperature profiles for RAs not tested in situ. INTRODUCTION RAs are designed to provide a life-sustaining environment for miners who cannot escape after a mine disaster. One of the major considerations for integrating RAs in mine environments is the thermal environment inside the RA and the impact that the surrounding mine conditions have on the temperature and humidity buildup. Previous research has observed that the metabolic heat of the occupants and the heat released by the CO2 scrubbing systems will cause the RA interior air temperature to increase. In addition to the increase in temperature, an occupant’s respiration and perspiration, as well as the chemical reaction of the scrubbing chemicals with CO2, will contribute to an increase in humidity within the RA. The resulting internal thermal conditions, if not controlled, can subject miners to conditions that can lead to heat exhaustion, heat stroke, or even death depending on the duration and magnitude of exposure. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and wind speed. It is used to assess the perception of indoor temperatures when workplaces are not sufficiently heated, cooled, or insulated to provide comfortable or healthy conditions. Mine Safety and Health Administration (MSHA) regulations require that RAs must be designed to ensure that the internal AT does not exceed 95°F (35°C) when the RA is fully occupied."

Jan 1, 2018

By A. Martikainen, H. Dougherty

"At the Kemi Mine, a recent expansion into the Surmaoja orebody required an increase in ventilation capacity. A new ventilation shaft was built with two main fans. The installation is near the entrance gate and only 1.7 kilometres from the nearest permanent dwelling. The main fans were first taken into use as exhaust fans in October 2014. Shortly after the fan installation, comments concerning fan noise were received from the neighbours. The first noise measurements were taken at the main fan installation site by Outokumpu personnel in March 2015. Due to higher than expected recorded values, during late June, 2015, a two-week environmental noise study was planned by the engineers and executed by a consultant specialized in noise measurement. The measurement results were analysed and compared to the requirements of the environmental permit and Outokumpu’s factory standards. While the measured values at the nearest dwelling were within the environmental permit limits, high noise values were recorded at the fan station. A second two-week study will be performed after construction of the main-fan heating station has been completed. Actions taken will depend on the outcome. INTRODUCTION The Kemi Mine is a part of the Outokumpu chain of integrated ferrochrome and stainless steel manufacturing in the Kemi-Tornio region in Finland. The mine itself is a large underground operation with a production capacity of 2.7 million tons of ore per annum. It is also the European Union’s only chrome mine, and at present (2015) the mine extracts 2.4 million tons of chrome ore per year. Safety, cost-effectiveness, and environmental friendliness are hallmarks of the Kemi Mine. Environmental impact produced by the operation of the mine is limited due to the insolubility of the oxide chromium ore, the gravity-based and chemical-free enriching process as well as the closed circulation system of the process water which serves both the whole mine and the enrichment process (Outokumpu, 2015). Importance of the environmental impact of the Kemi Mine is amplified by its closeness to the cities of Kemi and Keminmaa with the nearest habitants living less than 2 km away from the mine site. To show the cooperation with residents the Kemi mine organizes special “neighbour days” for the habitants of the areas closest to the mine. Also, information letters are sent to the neighbours, when changes that may affect the neighbours are being planned and executed."

Jan 1, 2016

By Bo Hyun Kim, Mark K. Larson

Fault-slip bursts induced by mining activities can result in severe damage to nearby mine development. In general, engineers designing rock support in burst-prone mines not only need to consider stress redistribution resulting from excavation, but also dynamic loading that results from seismic waves generated by large mininginduced fault-slip events. In this study, we simulated dynamic waves in sedimentary rock from a blasting source and from a mining-induced-seismicity source using a Universal Distinct Element Code (UDEC) model with discrete fracture networks (DFNs). Our purpose was to investigate the stability of openings and the adequacy of existing support systems at an underground limestone mine in South Korea. A baseline model with only static loading was also simulated, which verified observed stability under such conditions. The results indicate that the current support system of shotcrete lining is likely to work well under dynamic loading caused by blasting. However, when the dynamic source was a far-field fault-slip event, the dynamic loading exceeded the support capacity of the shotcrete lining. Thus, if a mine is operating in ground with an elevated risk of mininginduced fault slip, mine engineers should consider seismic wave propagation and ground motion distribution from a remote, mining-induced fault-slip event to determine a suitable support design.

Jul 1, 2023

By J. L. Mehaffey

A variety of chemicals offered by Armak were evaluated as dewatering aids for aqueous slurries of silica sand, sparsand and feldspar; an established commercial dewatering aid was used as a control. A number of Armak&apos;s potential dewatering aids yielded lower moisture retention values than did the commercial product on all of the mineral samples. In addition to the chemical dewatering evaluations, some of the mechanisms involved in the removal of water from these mineral samples were examined.

Jan 1, 1983

By J. F. T. Agapito

Two flat-lying trona seams 3-to 3.5-m thick, approximately 10 m apart, and at depths of 250 m are mined by room-and-pillar at OCI&apos;s Big Island Mine in Wyoming. Continuous miners and a yielding pillar system have contributed to improvements in resource recovery and productivity. Long-term stability with minimal subsidence is needed for a large portion of the mine beneath the Green River channel. This was investigated by computer modeling in 1990. Although results of the study indicated good long-term stability, recommendations were made for stress determinations to verify the model. Stress determinations made in 1997 showed pillar stresses 10% to 20% higher than the model stresses, and barrier pillar stresses 10% to 15% lower. This implies that higher panel stresses will be transmitted from the upper to the lower seam. A stability evaluation of the lower seam is planned before two-seam mining to assess entry widths and support requirements.

Jan 1, 1999

By Xun Luo, Yi Duan

A field trial of by distributed optical fiber sensing (DOFS) technique was conducted at a longwall coal mine in Australia. This investigation was designed to assess the applicability of DOFS for microseismic monitoring in mining. The experiments used commercially available optic fiber cables, geophones and associated data acquisition instruments – a fiber interrogator and a seismic recorder. The fiber cable was deployed in a 300m deep hole and in trenches of approximately 3.5 km long on the ground surface around and across the longwall panel being mined. The results obtained from the experiments have shown that DOFS is able to acquire microseismic data with quality that is comparable to geophones. It has been proven that DOFS can achieve higher spatial resolution for seismicity sensing and higher accuracy for locating events than a geophone network. These characteristics are particularly useful for using DOFS to monitor ground vibrations associated with ground caving processes and rock fracturing events induced by mining and civil engineering. It was also found that far more additional seismic events were recorded by the fibers than by the geophones. Automated data discrimination and processing methods must be developed in order to utilize DOFS for real-time applications.

Apr 26, 2022