Search Documents

By James S. Browning

Extensive deposits of kyanite occur in the southeastern United States, The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate:; for many years at the present-rate of consumption, According to Espenshade and Potter,1 the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30 percent kyanite. The tonnage of kyanite-bearing gneiss and schist is, much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina South Carolina, and at Graves Mountain, Georgia. Of the known deposits, only four were being mined for kyanite in 1967. These deposits are near Farmville and Dillwyn, Va., Clover S. C., and Washington, Ga. Production of kyanite and synthetic mullite increased substantially in 1965.2 Output of, domestic kyanite concentrate increased by 14 percent in 1965, establishing a record high for the fifth consecutive year. Estimated annual consumption of kyanite minerals and synthetic mullite was in excess of 100,000 tons. The manufacture of mulatto refractories accounts for most of the kyanite minerals consumed annually, but non-refractory uses are expanding.3 Most mullite refractories are used as furnace linings in metallurgical and glass manufacturing furnaces. The remainder is used largely for kilns, kiln furniture, and saggers by the ceramic industry. Small quantities of kyanite without calcination are used as a source of alumina in the manufacture of glass, electrical and chemical, porcelain, pyrometer tubes, and in the form of kyanite concentrate to increase the alumina content of fireclays. Kyanite is used to improve workability, increase strength, and to compensate for firing shrinkage in floor and wall tile and other ceramic products.

Jan 1, 1968

By R. Srikanth

Dust control in high production longwalls is a major problem requiring, among other things, careful attention to the design of operating practices, and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in U.S. longwalls; yet under certain conditions, 31 percent of the shearer operator's dust exposure can be due to support movement. Several methods have been developed for the control of shield-generated dust. Yet the need for better methods is apparent. In this paper, the amount of airborne respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. A total of ten experiments were conducted in five longwall faces in four different mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne respirable dust concentration immediately downwind of the shield moved, varied between 0.12 and 1. 75 mg/m3 in the five longwall faces. The mass of airborne respirable dust generated by shield movement was found to vary between 39 and 386 milligrams per shield move. The results from this study reveal that control of dust from longwall shields requires a combination of approaches involving alternative operating practices, reducing shield dust generation rate, increasing face air flow, and decreasing personnel exposure.

Jan 1, 1994

By J. C. Johnson

The problem of estimating pillar capacity in coal mines has motivated development of a variety of empirical equations. Most of these equations have arisen from experience and a very limited set of measurements that have, necessarily, been focused on particular regions or coal fields. Their applicability is often limited to a specific range of pillar sizes. This is of particular concern in the design of large gateroad pillars and small barrier pillars between panels. The result has been a variety of equations and equation coefficients that can calculate load estimates to size pillars. Inclusion of these equations in more sophisticated loading models, such as boundary element methods (e.g. LaModel and MULSIM) has been hampered by absence of a function that describes specific variation of coal strength within the pillar. A singular exception, to our knowledge, is a function corresponding to the Bieniawski pillar strength equation. Because of this, it is the only coal strength criteria inherently available in most boundary element models. This paper presents a general method for deriving local coal strength, as a function of distance from the pillar rib, for an arbitrary pillar strength equation. Integration of this function provides the strength of pillar regions, or cells, needed for boundary element models. The method is demonstrated for the Bieniawski, Maleki and Holland-Gaddy equations. The Maleki and Holland-Gaddy equations contrast strongly with Bieniawski as strengths are extrapolated to large pillars and barriers. This development provides a tool for incorporating any of the proposed empirical equations into a boundary element model, thereby allowing the analyst to choose the most appropriate equation for a particular region, coal seam and/or pillar size.

Feb 23, 2014

The ability to increase and maintain dragline productivity is a key mine driver for the Coal Creek Mine. The Coal Creek Mine is owned by Arch Coal Inc subsidiary Thunder Basin Coal Company; located near Gillette, WY. Coal Creek Mine overburden stripping is primarily accomplished by a BE-1570W walking dragline in combination with cast blasting and dozer assist for bench preparation. The two main variables impacting dragline performance are maintenance reliability and operator skill levels. The mine?s most recent process improvement efforts have focused on its most valuable asset - the operator. Various techniques have been used to reduce variability in the dragline operator?s digging performance. Utilization and communication of operator performance data, statistics, and video reviews have been of great value towards achieving this goal. Operators are given a chance to critique operational tendencies from a third-person point of view, and are also presented statistical feedback to support observations. From these sessions, operators gain knowledge as to what portions of the dig cycle can be improved in order to reduce cycle time and increase productivity. BACKGROUND The BE-1570W walking dragline was commissioned at Coal Creek in November 2006 after relocating from Arch of Wyoming located in southeast Wyoming. The first two years of operation the machine was performing simple side cast stripping due to the low ratio. Coal Creek Mine is a multiple seam operation with overburden thickness ranging from 24 to 140 feet. Early in 2009 the ratio increased to the point where transitioning to cast blast/extended bench stripping was necessary. The current mining conditions consist of a mixture of both stripping styles where the ratio allows. The dragline crews running the machine consist of a mixture of experience levels ranging from 30+ years to only a few years. It has been in this digging environment and slightly inexperienced personnel that the focus has been set for improvement in dragline performance.

Jan 1, 2011

By Jafar Safarian, Leiv Kolbeinsen, Stian Seim, Hossein Salehi

The present work aims to investigate the link between the oxidation and reduction of a weathered ilmenite concentrate in terms of phase transitions, microstructural changes, and element distribution. An ilmenite concentrate sample was pelletized and fired at 1000 °C in air, and as a result, the pellets were oxidized. The oxidized pellets were reduced by hydrogen gas at 1000 °C, which yielded almost complete metallization of the iron content of the pellets. The ore and the pellets were characterized in each step by XRD and SEM techniques, and distribution of elements and phases were investigated. Ilmenite, pseudorutile, and rutile were the main phases detected in the ilmenite concentrate sample, and depending on the weathering degree of the particles, different fractions of the phases were identified in their microstructure. It was found that irregular rutile grains dispersed in a pseudobrookite matrix is the morphology of the oxidized ilmenite phase. However, increasing microcracks and porosities were the only microstructural changes in the pseudorutile phase after oxidation in air. Studying the specific types of the ore particles and their oxidized and reduced forms indicated that the phase distribution in the ilmenite ore particles dictates the phase distribution in the oxidized and reduced ones. Results show that the morphology of the reduced particles includes a titanium (III) oxide matrix in which reduced iron globules are dispersed.

Feb 8, 2021

By S. Khoshjavan

Separation of refractory rock phosphate (P2O5 = 11.5%) from the Dalir area, Iran, containing quartz, calcite and other impurities, by calcination and flotation processes has been successfully used to upgrade the phosphate values. Petrographic studies of this ore showed that collophanite was the major phosphate mineral and the main gangue minerals were calcite, dolomite and quartz. The results of characterization studies showed that the liberation degree of apatite occurred below the average grain size of 140 µm. Preliminary flotation tests were used to process the phosphate samples. Results of preliminary flotation tests showed that they don?t contain any desirable efficiency (grade or recovery) of P2O5. Calcination was the best process for preconcentration of this ore. In the desliming stage, about 14.4% of total P2O5 was removed. Encouraging concentrate grades were obtained after flotation with anionic and cationic flotation, successively. The reagent schemes that have been used in this study consisted of COCO-amine acetate and fatty acid as silicate and apatite collectors, respectively, as well as fuel oil and anionic poly acryl amid as promoter collectors. The optimum pH values for direct and reverse flotations of phosphate were 11 and 6, respectively. Experiments conducted using d80=140 µm deslimed fractions has yielded an acceptable grade of more than 30% P2O5 with a recovery of more than 62%. Finally, a laboratory flowsheet for the processing of Dalir refractory phosphate ore has been proposed.

Jan 1, 2011

By J. G. Groppo

The Andritz Ruthner Inc. hyperbaric filter was evaluated at a pilot scale for dewatering fine coal cleaned by froth flotation. The pilot scale dewatering testing was conducted at a solid feed rate ranging from 100 lbs to 200 lbs/hr-ft2. Effect of hyperbaric operating parameters and addition of various surfactants and flocculants were evaluated on dewatering of fine coal. The tests data indicated that for the minus 100 mesh and minus 28 mesh clean coal product, the Andritz hyperbaric unit provided filter cake containing 23 percent and 14 percent moisture, respectively.

Jan 1, 1996

By H. B. Oblad

Coal/pyrite fines were froth floated in a laboratory cell to examine the rate of pyrite recovery during conventional coal flotation. The effects of collector, particle size and carbon to total sulfur ratio on the kinetics of recovery were investigated. These data coupled with microscopic examination suggest that miniscule amounts of coal that remain attached to the pyrite surface affect the rate of flotation of pyrite.

Jan 1, 1985

By S. K. Kawatra

Under normal conditions, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. In order to reduce this pyrite recovery, it is first necessary to determine the primary recovery mechanism, as different measures are required for reducing entrainment, locked-particle flotation, or true hydrophobic flotation. In this paper, evidence is presented which suggests that hydrophobic flotation is not the major mechanism for recovery of liberated pyrite, and that the bulk of the recovered pyrite is there either as a result of simple entrainment or by being physically locked with floatable coal particles.

Jan 1, 1991

By S. J. Zagula

Improved desulfurization of Illinois coals is a widely Shared research goal. The development of a physical cleaning strategy and the results of a project to demonstrate technical and economic feasibility of producing a low sulfur compliance coal from the Illinois Basin are reported. Processing flowsheets to extend or retrofit existing preparation plants are considered. Comminution, conventional and micro-bubble flotation, and selective agglomeration technologies were investigated to maximize pyrite rejection while maintaining high product yield. Batch bench scale testing was followed by continuous pilot plant studies. Parameters included grind size, flow rates, pulp density, aeration, agitation, and reagent dose. An economic evaluation of targeted processes is included.

Jan 1, 1987

By S. A. Rholl

This paper describes the Bureau of Mines experimental test program which evaluated the effectiveness of using high explosives to enhance orebody permeability. To determine the effect of stress on the fracture network generated by blasting, fifteen single-hole laboratory tests in granite blocks up to .067 m3 (2.4 ft3) in size were blasted using .12 to .20m (4.8 to 8.0 in) of 1.6xl0-3-, 3.2xl0-3-, or 6.5xl0-3-kg (25-, 50-, or 100-grain) detonating cord. In situ stresses were simulated using polyaxial load cells to apply uniform stresses of 1.72xl06 to 1.76xl07 Pa (250 to 2550 psi). All of the blocks were sawed to expose the blast-induced fracture patterns for analysis.

Jan 1, 1991

By Richard D. Begley

This paper will present the results of an analysis of several abandoned coal mine projects and includes field data for over a dozen different reclamation projects recently completed in the state of West . Virginia. The analysis was performed with the objective of summarizing and or classification of the environmental consequences with reference to the characteristics of the mining facilities (surface, underground, etc.). The analysis also addressed the itemized cost of remediation with respect to procedures, environmental concerns and time. The results of the analysis are that each abandoned coal mine site in West Virginia have/had many unique features and in most cases include a combination of environmental concerns that complicate comparisons. The study also revealed that the abandoned mine land program for mines abandoned prior to 1977 that is being financed by a tax on the production of coal, has produced many benefits for the state of West Virginia. This grant program administered by the Office of Surface Mining, has resulted in a high quality methodology of remediation that has been successful for many years in greatly minimizing and/or eliminating environmental concerns from abandoned coal mines.

Jan 1, 1997

By Nikhil Dhawan, Débora Moreira, Yogendra Pratap, Himanshu Tanvar

A glauconitic siltstone sample with a potash content of 10% is investigated as a potential potash source. The fine grain structure comprises potash bearing phases of glauconite, muscovite, and microcline. The as-received samples showed poor dissolution ~ 5%. Planetary ball milling was attempted for the dissociation of the underlying silicate structure for the potash release, and ~ 60% potash was obtained after 12-h milling. Mechanical activation (8 h, 60% NaOH) prior to heat treatment (600 °C, 30 min) was found successful in recovering more than 95%K values from glauconite. The final residue consists mainly of quartz, indicating a complete breakdown of the silicate matrix. The mechanical activation process followed is simple, adaptable, and less energyintensive compared to existing methods.

May 4, 2020

By Rob Thomas

It is generally agreed that standing support should be installed in roadways that will for various reasons, be holed through with a longwall. Considering the magnitude of the associated abutment loading in conjunction with the need to ensure that the material used is cuttable, some form of cementitious support is often used.

By S. McAlister

This paper outlines the development of the Falcon enhanced gravity separator. Design objectives included continuous operation with sharp separations, mechanical simplicity, minimization of process water demand, the ability to apply a centrifugal field up to 300G's, unit capacity in excess of 100 t/h within a footprint of 10 square meters, a capital cost below $US 4,000 per t/h capacity, and total operating costs of less than $US 0.40 per tonne. A parallel development has been inexpensive, effective, semi-continuous equipment for recovery of precious metals in the free metallic state. These objectives have been largely met. There are significant opportunities for the technology in many mineral processing applications.

Jan 1, 1998

By Delbert Hamilton, Christopher Snyder

In the last three years there have been four uncontrolled heating events in mines that have been attributed to the use of polyurethane foam as a void fill product. These heating events are due to the exothermic reaction that occurs during application of these polymeric products. These events led the Mine Safety and Health Administration to issue a safety alert on polyurethane products used in void filling and ground consolidation in mining, with the goal of educating the mining community about this potential hazard. This paper provides an overview of various types of polymeric products and best practices, the factors that contributed to the heating events, and case studies involving polymeric products.

Jun 25, 2024

By S. M. Robinson

Wollastonite is recognized as one of the most unique, non-metallic minerals in the world. Its history for use in industrial applications is recent compared to other minerals, however, its distinctive physical properties, such as acicular particle shape, and alkaline pH creates incorporation possibilities ranging from bowling balls to automotive fascia, from ceramic tiles to automotive brakes, and from thermal insulation board to industrial and trade sale coatings. Its future use will be impacted by the exploitation of deposits which will ensure maintenance of the acicularity and purity of this naturally occurring mineral. Additionally, closely held surface treatment technology will open up additional niches requiring highly engineered performance.

Jan 1, 1995

By Steven I. Olson

Since the introduction of froth flotation, the Florida Phosphate Industry has faced the challenge of coarse particle -850 +425µm (-20 +35 Tyler mesh) beneficiation. Several techniques have been used to upgrade this difficult size range. This paper discusses one approach that has met with success; namely, improved fractional recoveries through enhanced areation and improved material transport characteristics via larger than standard flotation cell mechanisms.

Jan 1, 1981

By E. H. Cho

An acid mine drainage sludge sample containing 3.6% Mn, 0.18% Ni, 0.15% Co and 0.39% Zn was obtained from the central part of West Virginia and leached with sulfuric acid at pH 3 and at room temperature. Air was bubbled through the leach solution to precipitate the iron content from the solution at pH 4.5. The leach solution contained 258ppm Zn, 105ppm Ni, 90ppm Co and 2050ppm Mn. Three distinctive solvent extraction studies were performed to selectively extract these metal ions in a sequential operation with DEHPA, Cyanex 272, and then Lix 84. The AIO ratio was 1 and the extractants were diluted 10 times with kerosene. A study of solvent extraction with DEHPA showed that Zn could be extracted without Ni or Co up to pH 2.75. A pH of 2.75 is considered to be the optimum pH to maximize the selective separation of Zn from Mn. The separation factor of Co over manganese suggests that the two metal ions be extracted together by Cyanex 272. The separation factor of Co over Ni indicates that these two metal ions can be separated most effectively around pH 5.3. Also, Ni can be effectively extracted by Lix 84 above pH 5.5.

Jan 1, 1993

By G. H. Harris

The flotation behavior of two high sulfur coals using a non-ionic surfactant as collector from two series of compounds containing oxygenated functional groups was studied in detail using a 2-liter Denver flotation cell. The performance of these reagents was compared with that of an oily collector, namely dodecane. The results showed that at the same coal recovery, a much lower dosage of these non-ionic surfactants was required as compared with that of dodecane. More import was the performance of these compounds as promoters for oxidized as well as un oxidized coal. Mechanisms of interaction of these compounds with the coal are suggested.

Jan 1, 1993