Search Documents

By T. M. Gurr

Large quantities of phosphate rock are mined and processed in Central Florida (Figure 1). The phosphate rock from the mines is further processed in "chemical plants" to produce phosphoric acid (Figure 2). A by-product of the processing' of the phosphate rock to produce fertilizer chemicals is an impure form of gypsum referred to as phosphogypsum. For each ton of phosphate rock processed, approximately 1.5 tons of phosphogypsum is produced (Figure 3). The typical method to dispose of this by-product gypsum is to stack it in large piles, locally referred to as gypsum stacks or gypsum fields (Figure 4). These gypsum stacks have been the focus of many studies in recent years in an attempt to identify the potential for ground water and/or air pollution associated with the stacks. This paper attempts to discuss some of the ground water impacts and current attempts to minimize these impacts.

Jan 1, 1990

By Nathaniel Arbiter

A fully-instrumented driving mechanism has been constructed to study the power, aerating and solid suspension characteristics of several laboratory flotation machines. Machines operating over normal flotation speed ranges give constant power numbers in liquid' systems indicating that they operate under fully baffled turbulent flow conditions. Owing to lack of geometrical scaling, power numbers for different sizes of cells of the same make are different. Even larger differences occur between cells of different manufactures. For a given impeller, varying the tank size did not significantly affect the power consumption. Tank geometry and baffling has a slight effect on power consumption with shrouded impellers. For a given impeller speed, suspension height decreases while power increases with increasing mass of solids in suspension. While power consumption is hardly affected by particle size and clearance between the impeller and tank bottom, the suspension height significantly increases as clearance increases and as particle size decreases. Aeration was found to affect not only power but also the suspension characteristics of the machine. For closely sized particles drastic sedimentation occurred when a critical value of the air flow number was exceeded. The critical air flow number decreased with increasing particle size. This effect was less marked with a wide particle size range. The self-aerating capacity of flotation machines increases with cell size at a given speed for the same impeller-shroud system, but decreases in the presence of frother and solids. Equations have been established for correlating all of the studied variables. Data taken from the literature were also correlated with these equations.

Jan 1, 1968

By Arun Kumar Singh

Wide variation in the nature of the coal seams and the surrounding rock mass of the Indian coalfields and very little information about the associated stress fields were observed to be the major hurdles in the straight forward application of a continuous miner (CM) based mechanised depillaring approach. Due to various techno-economic reasons, a considerably large number of coal seams have been developed and are standing on pillars in India. The development of pillars is done as per Indian coal mines regulation, which results in pillars of relatively large size. In fact, the large size of the pillars provides stiff natural support to control caving of the massive overlying strata. However, the size of these pillars is not conducive for the single pass pillar stripping technique and, therefore, there is a need for pillar splitting before pillar extraction/retreating. Splitting of the pillar may reduce the competency/stiffness of the pillar, which creates a chance of overriding during final extraction below a massive roof stratum. This paper first discusses the existing coal mining scenario in India followed by a brief presentation of geo-technical details of pillar extraction at the three sites where a CM has been introduced for depillaring/pillar retreating in the country to date. Based on past rock mechanics experiences with conventional depillaring faces, stability issues of the pillars, fenders, and stumps in and around the depillaring face are discussed. This may prove to be an important factor in the success of future CM faces. It is recognized that the application of the modern strata movement monitoring techniques may improve operation safety by providing valuable qualitative and quantitative information that can be used to improve the design of modern concepts like roof bolt based breaker line support during pillaring.

Jan 1, 2009

By Takayoshi Otsuka, Taher Elsamni, Ashraf Bou-Krisha, Takaya Takimoto

"INTRODUCTION Tunnel is a closed space structure and it is necessary to ensure the sufficient time and route for safe evacuation for the tunnel users in case of a tunnel fire. In order to do so, damages and collapse of the tunnel linings and the secondary disasters can be avoided. Furthermore, the road tunnel is one of important infrastructural facilities and stopping its function for a long time for a tunnel fire could cause a great economic loss. Therefore, the tunnel structure shall be the one which can be repaired as soon as possible, and the fire protection methods need to be selected among those which enable the service to start as early as possible. The necessity of the fire protection works is evaluated for the tunnel structure with the consideration of the expensive tunnel construction cost and the economic effects of the tunnel service. Naturally, the fire protection works, which can protect the tunnel linings from the tunnel fire with small repairs, are inevitable. Design engineers of the fire protection works estimate the scale of fire from the degree of damages on the linings and its repair cost, the effect of fire extinguishers placed inside of the tunnel, the secondary disasters in accordance with the tunnel lining damages if any, and the ratio of fire protection cost calculated from tunnel operation cost. Based on this information, the engineers design the fire protection works according to the permissible limits Among the design cases of the tunnel fire protection in Japan, as shown in Table 1, there is no cases that used the fire temperature-time curve to design the fire protection works for large fire caused by vehicles catching fire. However, the most of cases used 30-60 minutes for fire duration based on the entry prohibition of dangerous goods carrying vehicles or the effect of early fire fighting. This paper will study the variation between different methods used for fire protection in road tunnel in Japan to evaluate them and try to found some recommendations. Especial l care will be attention to Polypropylenes (PP) which is starting to be applied lately."

Jan 1, 2016

By J. A. González-Anaya

This laboratory work presents a study of the effect of ultrafine grinding on the gold recovery of a highly refractory gold concentrate. The particle size of the concentrate was P80 = 46 µm and the main species present were quartz (28.58%), dolomite (25.63%), pyrite (20.93%), arsenopyrite (15.39%) and 112 g/t gold. After optimizing hydrated lime and lead nitrate additions, standard cyanidation with 1% NaCN, pH = 12.3, 25% S/L permits to recover only 9.4% of the gold. Different particle sizes were submitted to cyanidation. When the concentrate was ground to ultrafine sizes (P80= 4.6 µm), the gold recovery for the same cyanidation conditions increased to 67%, with cyanide consumption of 66.7 kg NaCN/t. Additional tests were performed in order to reduce the cyanide consumption. The reduction of the cyanide concentration in the leaching solution from 1 to 0.5% and the addition of 100 g Pb(NO3)2/t allowed the reduction of the cyanide consumption to 27.6 kg NaCN/t (58% reduction), while maintaining the same gold recovery of 67%. The remaining gold could be present as very fine inclusions or in solid solution in the matrix.

Jan 1, 2011

By CASSANDRA L. HOEBBEL, Emily J. Haas, MARGARET E. RYAN

In recent years, there has been increasing interest in the role that individual factors play in health and safety (H&S) outcomes in the mining industry. Two surveys, one measuring self-reported routine safety performance and one measuring individual perceived competence in the non-routine knowledge, skills, and abilities (KSAs) critical to emergency response, were administered to two samples of mineworkers in separate research studies over a 2-year period (N=2,020 and 696, respectively). Eight demographic items were common to both surveys and their associations with each performance outcome were tested in response to a series of exploratory research questions.

Jan 9, 2022

By V. Rajaram

The Metropolitan Water Reclamation District of Greater Chicago (MWRD) imposed a no-blasting specification (blasting is restricted to the construction shaft and shaft bottom or boot) on the Deep Tunnel project in 1988. This was prompted by numerous complaints from the residents in the vicinity of the project, and controversies experienced on previous projects from blasting the rock overlying the tunnel. This paper will describe the methods utilized by two major contractors who are driving 20 km (12.5 of tunnel along with drilling over 36 shafts under this restrictive specification. The impacts on design, construction, schedule, cost, and the environment are detailed.

Jan 1, 1991

By Gerald Zink

The work described in this paper is sponsored by the Bureau of Mines for the purpose of accelerating the drilling of roof bolt holes and reducing the quantity of materials needed to fill each hole. A high-speed small-hole drill has been fabricated and tested in the laboratory. High priority has been given to safety, reliability, and compatibility with underground coal mining practice. The combination of drag bits and erosion jets is designed for high penetration rate, long wear life, and uniform hole size in a variety of sedimentary strata. A reliable high-pressure high-speed swivel feeds water to the bit at about 4 1/min (1 gpm). The duplex hydraulic intensifier which drives the jets has a 40 kw capacity (30hhp) Results of recent full-scale laboratory testing are presented.

Jan 1, 1978

By Frank Matter

The production of ultrafine slurries and powders is possible with small media made out of Si02, A1203, Fe203, Zr03 or other raw materials due to the fact that since approximately 12 years from now, entirely new machines have been developed which allow to use this small media for the production of ultrafine pigments. Basically we distinguish between two grinding methods which are: A.) Dry Grinding with Air Classification: This method is used for more than fifty years but only since four years this technology is realized with small grinding media. Many problems like cooling, abrasion, control of the media flow, separation media from product, grinding media recycling etc. had to be resolved before it was possible to get in full production with this new system. Hereafter a flow-sheet of such a TRZK mill with an air classifier especially designed to produce end products with a top size between 2,5 and 3,0 micron and with an average particle size between 0,3 and 0,5 micron.

Jan 1, 1983

By Karl R. Zipf

A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine. The gas samples are drawn via vacuum pump to the surface and are typically analyzed for oxygen, methane, carbon dioxide and carbon monoxide. Results of the gas analyses are displayed and recorded for further analysis. Trends in the composition of the mine atmosphere, such as increasing methane or carbon monoxide concentration, can be detected early, permitting rapid intervention that prevents problems, such as a potentially explosive atmosphere behind seals, fie or spontaneous combustion. TBS is a well-developed technology and has been used in coal mines around the world for more than 50 years. most longwall coal mines in australia deploy a TBS, usually with 30 to 40 monitoring points as part of their atmospheric monitoring. The primary uses of a TBS are detecting spontaneous combustion and maintaining sealed areas inert. The TBS might also provide mine atmosphere gas composition data after a catastrophe occurs in an underground mine, if the sampling tubes are not damaged. TBSs are not an alternative to statutory gas and ventilation airflowmonitoring by electronic sensors or people; rather, they are an option to consider in an overall mine atmosphere monitoring strategy. This paper describes the hardware, software and operation of a TBS and presents one example of typical data from a longwall coal mine.

May 1, 2013

By M. Sears, G. S. Esterhuizen, Z. Khademian

According to the 2010-2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accidents in U.S. longwall mines were caused by roof instability. Gateroads are subject to significant changes in loading conditions from the development to the longwall abutment loading phases. When combined with thinly bedded shale roof, found in many U.S. longwall coal mines, the design of efficient roof support becomes challenging. In previous work, the Bonded Block Method (BBM) modeling of roof by UDEC was validated against field extensometer measurements in a longwall gateroad entry roof at a 180-m depth of cover. The BBM was shown as capable of capturing delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. This paper presents the recent findings on the roof-support interaction using BBM models of the same longwall entry. The effects of cable bolts, roof bolt density, and strap support on potential roof instability are studied. These types of studies are difficult and costly to conduct in an operating mine. Results show how the contribution of bolts, straps, and cable bolts can be quantified using the BBM models. The study demonstrates the potential for BBM numerical models to help understand the complex roof and support system interactions and to assist with optimizing gateroad support systems.

Feb 1, 2023

By R. Q. Honaker

Recent research has shown that enhanced gravity separators provide the opportunity to effectively clean I mm x 37 micron coal. At Southern Illinois University, a detailed experimental program was performed on a continuous Falcon Concentrator, which was found to achieve separations at mass throughput capacity values in excess of 100 tonnes/hour. The apparent particle separation density for I mm x 73 micron coal was about 1.60 with relatively high efficiency (Ep = 0.12). Typical ash and sulfur rejection values of 85% and 70%, respectively, were achieved while recovering 85% of the combustible material. Metallurgical and efficiency data from the evaluation are presented in this publication.

Jan 1, 1998

By D. C. Torre

The need for a successful, efficient and reliable continuous face- haulage .system for use with continuous mining machines has been apparent since the first continuous miners were introduced some twenty-five years ago. Some thought and effort were given to the development of continuous haulage over the last twenty years or so. Some initial success was experienced in this area by The Long Company with a system involving bridge conveyors, as far back as the late 1950's. However, extensive success with continuous face haulage for use behind modern, high product¬ion, continuous miners escaped the industry until the early 1970's. It is true that continuous face haulage was successfully introduced into low seam mining, generally in seams ranging under 1.07 m (42") in height, in the 1960's, for use with relatively low production, low seam, auger type continuous miners. However, those available systems which have achieved success in the lower seams, where relatively low capacities are adequate, are not directly applicable for use with today's medium and high seam miners with their standard production capacity of 9.1 - 10.9 mtpm (10 - 12 tpm). Since the late 1960's and early 1970's, several machinery manufacturers, and at least two major coal companies, have devoted considerable expense, time and effort to developing truly successful continuous face haulage for use in coal seams ranging upward from 1.2 m (4') in height. Continuous face haulage equipment has been developed in the last five years employing a variety of transportation media and design concepts, including some which have received wide publicity such as those employing hydraulics, and pleated belt. The truth of the matter is, however, that the only universally applicable and widely successful continuous face haulage equipment introduced to date has been that employing a combination of bridge conveyors and mobile, self-propelled, bridge carriers, connected at the inby end to the tail of the high production continuous miner, and at the outby end attached directly to the panel conveyor (Fig. 1 & Fig. 2) or, on occasion, to a short, self-contained conveyor which, in turn, empties directly onto the panel conveyor. While these bridge type continuous haulage systems are available with both belt and chain conveyor components, the most widely applied and successful system in seams above 1.07 m (42") in height is that offered by The Long-Airdox Company. The standard unit for use with 9.1 - 10.9 mtpm (10 - 12 tpm) continuous miners is normally equipped with belt. However, they have built, and successfully applied, versions of this system employing chain conveyors, (Fig. 3), mainly for operators having extremely difficult mining conditions, including excessive amounts of water

Jan 1, 1977

By W. Petruk

Mineral liberations that would be obtained by grinding an ore to a specific size can be predicted by analyzing unbroken ore pieces, and mineral liberations in ground ores and mill products can be determined directly by image analysis. Predictions of mineral liberations are made by measuring size distributions and textures of mineral grains by image analysis, and using liberation models. Ground ores and mill products are analyzed to determine the proportion of mineral that is liberated, and the data are used to evaluate mineral behaviour during mineral beneficiation. The liberation data for minerals in a suite of mill products from a circuit are processed by a materials balancing technique to calculate recoveries of minerals in different types of particles throughout the circuit. The liberation-materials balance data define mineral recoveries; define the behaviour of an ore in a concentrator, pilot plant or bench test; and indicate whether recovery improvements are possible and/or feasible.

Jan 1, 1991

By D. H. Steve Zou, Cui Lin

"This paper first discusses the basic attributes of sustainable mining and the responsibilities of various steak holders including mining companies, governments, and engineers. It is followed by a brief overview of the current practice on regulations, inspections, waste management and mine closure planning in Canadian mining industry. A case study is then presented as an example of sustainable mining where mine planning, mineral recovery, environment protection, reclamation and community development were integral parts of the overall strategy. A comparison of the mine site before and after mining is made to demonstrate the ""best practice"" in modern mining.Sustainability in Mineral Resource Development Extraction of mineral resources and other natural resources on the Earth has been and will continue to be an essential activity necessary to support human’s life. We live on the planet and depend on the available resources to survive. The extracted materials form the base to support modern life. However, we must be aware of the fact that mineral resources are limited on the Earth and may not last forever. Every time we extract one ton of materials, there is one ton less. They are not able to regenerate or regrow. One can ask a simple question: How long will they last? Or, is there anything left for our great grandchildren and many generations to come? The answer is not simple. Some minerals have become scarce or about to deplete. Some minerals may last longer. The reserve of a type of minerals depends on what we have discovered and the minable amount depends on accessibility and technology we have. Even if there are minerals in the deep ground, we may be limited by our technological capability. At the same time, we also need to understand the action of mineral extraction from the ground and the consequences of that action. Mineral extraction is a very hard work. We must break the ground to extract the ore, either through surface mining or underground mining. This action means disturbance of the land where we live. The disturbance is much more visible in surface mining than underground mining. The disturbed land, if not properly reclaimed after mining, is not going to be reusable. The very purpose of extracting minerals from the ground is to support our life but the action has a negative impact on our life. How can we reduce and limit disturbance of land from the action of minerals extraction? How can we make the disturbed land reusable? These issues must be properly addressed and a balance achieved."

Jan 1, 2017

By David A. Fawcett

An auxiliary cross-pit mining system, working in tandem with the prime excavator, is evaluated technically, operationally and economically for application in the selective removal and replacement of soils and unconsolidated ovezburden. Previous studies on cross-pit technology and applications of this technology are briefly reviewed. Stratigraphy plus pit, operating and economic parameters are assumed and applied in the evaluation and comparison of a base case dragline system with two alternatives - a dragline/scraper-dozer combination and a drag- line/cross-pit system combination. The economics of the proposed cross-pit system favour it as a viable alternative to conventional systems.

Jan 1, 1981

By C. Hilton

Arch Coal Inc. has implemented and sustained Best Practices at its four western mines through utilizing foremen in ongoing time studies. A prime benefit is the unique opportunity provided to front line supervisors. To date, 48 supervisors have participated in this program. Each quarter a new team is assembled with members from each operation. During three month blocks the supervisors conduct studies at each mine and identify best practices to implement at their own mine. Ongoing Best Practice and Action Item lists are reviewed each study. Mine management edits, prioritizes and monitors the completion of the proposed action items.

Jan 1, 2010

By Lyle A. Hale

The subject area known as upper Dry Valley is located 15 miles due east of Soda Springs in Sections 14 and 23, Township 9 South, Range 44 East, Caribou County, Idaho. The railroad extending from Soda Springs to its terminus at El Paso's Maybe Canyon mine is 8z miles to the north in lower Dry Valley. Initial data derived from trench work in 1962 revealed a variety of econom¬ically significant alterations of the phosphatic beds related to the rather unique geomorphic development in the northern part of phosphate lease 1-012989. It was apparent that such conditions, while valid for near-surface beds in a strike direction, would be misleading if projected to the proposed depth limits of strip mining. Consequently, a subsurface mapping program was initiated in 1963 to determine: (1) the depth and horizontal extent of weathering and related phe¬nomena, (2) the depth, thickness, and quality of ore beds and intervening strata, and (3) structural geology as a guide for mining procedures. Successful use of a scintillometer in 1956 to detect the subcrop position of phosphate beds in the Smokey Canyon area of southeastern Idaho led to the conclusion that gamma radiation surveys of drill holes could be a useful aid in subsurface mapping. The objectives of this paper are: (1) briefly to describe geologic features characteristic of the phosphate lease area and (2) to demonstrate the practical application and theory behind gamma radiation logging as an effective tool in the economic evaluation of a phosphate lease.

Jan 1, 1969

By H. Hinds

Plant testing of DuPont's Activator Technology in the vat leach circuit of the Homestake mine shows increased gold recoveries of 3-5%. Activators are catalysts of gold dissolution in cyanide solution. DuPont received the patent for this technology in January, 1996. The test was run in the west sand plant alternating control and activated vats to reduce the variability in head grade and cyanide consumption. Activated vats had gold in the preg solutions earlier, higher gold recovery, and lower gold residuals. Activator addition did not adversely affect mill operations or the environment. Optimization of the technology continues.

Jan 1, 1997

By Subhas G. Malghan

Feldspathic deposits occur widely throughout the United States, but North Carolina, California, Connecticut and South Carolina accounted for over 80% of the total domestic feldspar output for the year 1973.1 Pegmatites and granites constitute the major feldspar reserves of the United States,2 and in addition, feldspar is produced as a by-product by firms whose major products are spodumene and mica.3 Feldspar is concentrated by hand-cobbing and flotation; the latter forms the major method of separating and concentrating feldspar. Feldspar flotation is practiced in the United States, Mexico, Finland, Norway, West Germany, Japan and the USSR. According to the U. S. Bureau of Mines estimates, the production of feldspar in the United States and rest of the world were 704,000 tons and 2,514,000 tons respectively. Feldspar is principally used as a flux in making glass, pottery, porcelain, enamel,-tile and other ceramic products. In recent years, the domestic feldspar industry is faced with a number of problems. As a result of increased cost of energy and the introduction in 1972 of new legislative programs relating to air, water, and noise pollution, land-use restrictions, and mined-land rehabilitation, the production costs have increased. Apart from the increased cost of operation, an operational problem exists with the feldspar producers in North Carolina, especially those in the Spruce Pine area. This problem is concerned with the use of hydrofluoric acid in the feldspar flotation. Feldspar producers in Spruce Pine, North Carolina have been discharging process waste water into the North Toe River. The mill waste water contains active fluoride ions. Fluoride in excessive concentrations is undesirable in waters used for drinking. It is stated that water

Jan 1, 1976