Search Documents

By J. Riss, S. Gentier, A. Marache

The study of the hydromechanical behaviour of fractured rock masses requires a detailed knowledge of the isolated fractures. The aim of the paper is the simulation of the evolution of the void space, located between both walls of a fracture, during a shear test under constant normal stress. Results of the mechanical simulation model are first validated then analyzed in detail. We observe that, during the shear process, there is an opening of the fracture with the creation of preferential channels. These channels are determined at the early phase of the shear process (pre-peak phase), and we observe during the post-peak phase that void areas increase in size rather than the creation of new apertures. Die Untersuchung des hydromechanischen Verhaltens eines zerlegten Felsmassivs erfordert genaue Kenntnisse der einzelnen Spalten. Ziel dieses Artikels ist die Simulation der Evolution des Hohlraumes zwischen den beiden Wänden eines Spaltes während eines Abscherungsexperimentes unter konstantem senkrechtem Druck. Die Ergebnisse der Modellierung werden zunächst mit dem Abscherungsexperiment verglichen und dann im Einzelnen ausführlich analysiert. Während des Abscherungsprozesses tritt eine Öffnung des Spaltes auf, die die Bildung von bevorzugten Fliesswegen fördert. Diese Kanäle werden bereits in einer frühen Phase des Abscherungsprozesses (pre-peak Phase) festgelegt. In der post-peak Phase tritt dann eher eine Vergrößerung dieser Kanäle, als die Bildung neuer Hohlräume auf. L’étude du comportement hydromécanique d’un massif rocheux fracturé ne peut se faire sans une connaissance approfondie des fractures le constituant. L’étude présentée dans cet article concerne la simulation de l’évolution de l’espace des vides présent entre les deux épontes d’une fracture au cours d’un essai de cisaillement à contrainte normale constante. Les résultats du modèle sont tout d’abord validés puis analysés en détail. On constate que, au cours du cisaillement, il apparaît une ouverture de la fracture permettant la création de chenaux préférentiels. Ces derniers sont déterminés très tôt dans le cisaillement (phase pré-pic), et on observe dans la phase post-pic davantage un accroissement de la taille des chenaux plutôt que la formation de nouvelles zones de vides.

Jan 1, 2003

By D. van Heerden

In the mining industry abrasion caused by both sliding and impact have over the years resulted in costly damage to installations such as ore passes and silos. Good geotechnical practices combined with the use of a high quality abrasion resistant concrete can prolong the life of such an installation and minimize problems associated with abrasion. In order to maximize the life of an abrasion resistant concrete, the choice and combination of the correct raw materials (cement, aggregate and fibre) and overall mix design needed to make up such a concrete are important. This paper presents technical data and practical experience showing that concrete formulated with calcium aluminate cement resists severe abrasion conditions better than similar OPC-based concretes.

Jan 1, 2005

By M. L. Smith, G. Karunatillake

Lead-zinc production at MIM, Mount Isa includes three mines, a lead concentrator, zinc filter plant and lead refinery. Lead production is vertically integrated with lead-silver bullion shipped from Australia to London for refining. Zinc is sold as a concentrate. All three mines have reached varying states of maturity mining a multitude of orebodies having significant variation in grades and metallurgical recovery for three metals. Based on current levels of measured resources, the remaining project life is at least ten years. The objective is to schedule production over the life of all three mines so as to maximize the present value of the complex. Additional scheduling complexity arises out of the implementation of long-term schedules, capital expansion projects for both mining and processing, the presence of substantial inferred reserves and interactions with MIM copper production. A large-scale, time-dynamic, life-of-complex Mixed Integer Program (MIP) production schedule was formulated to optimize lead/zinc cash flow based on a detailed life of project production scheduling study. The requirements for such a study are detailed herein. The operational feasibility of the MIP solution is compared against a non-optimal approach to strategic life-of-mine scheduling. The strategic planning emphasis placed on the MIP is compared to the implementation of a life-of-mine schedules at Mount Isa using spreadsheets and other popular commercial mine schedulers.

Jan 1, 2003

By J. P. Theron

Paper written on project work carried out in partial fulfilment of Phd.(Process Engineering) degree Process modelling is an essential element in the development of advanced (model-based) process control systems, accounting for up to 80% of the cost of development. Often, models based on historic process data are the only viable option when dealing with processes that cannot be modeled cost-effectively from first principles. Despite major advances that have recently been made in the field of nonlinear process modeling, some basic idea of the dynamic behaviour of a process system is important prior to system identification. While many process systems seem unlikely to be linear, the possible nonlinear aspects of their dynamics are not necessarily supported by the data. This may have significant implications for subsequent system identification or interpretation of the data. For example, it is quite possible that an underlying nonlinear deterministic signal may be obscured by a high degree of measurement or process noise, to the extent that it may be critical in the choice of model to fit to the data. The method of surrogate data analysis has recently been proposed as a means to classify the underlying dynamics of complex systems, and in this paper the use of Fourier transform surrogates to classify process systems is explored. Keywords: modelling, process control, simulation, surrogate data analysis, nonlinear systems.

Jan 1, 2004

By I. Alp

Application of magnetic separation was investigated for the enrichment of colemanite ores by removing the magnetic gangue fraction. The detailed XRD analysis of the ore has indicated that the gangue fraction is composed predominantly of the iron-bearing silicates such as smectite and, to a lesser extent, illite. Magnetic susceptibility measurements of the colemanite and gangue samples have proved that colemanite is diamagnetic in character whereas gangue fraction is weakly paramagnetic to allow the removal of this fraction by magnetic separation. Magnetic separation of the crushed and sized ore samples (-5 mm +75 µm) was performed using a high intensity permanent magnetic separator. Under the test conditions a colemanite concentrate (41.29 wt.% B2O3) was found to be produced from the crushed ore (30.76 wt.% B2O3) at a recovery of 96.76%. These findings suggest that magnetic separation has great potential as an alternative process for the production of a concentrate of commercially sufficient grade.

Jan 1, 2009

The influence of varying amounts of magnesia, silica, and alumina in iron ore sinter on its mineralogy, reducibility index (RI), reduction disintegration index (RDI), physical breakdown (AI and TI), and production properties (coke breeze rate) were examined. It was found that the mineralogy of iron sinter can more easily be predicted from its chemical composition than from the RI, RDI, AI or TI. Anticipating the consequence that varying amounts of MgO and SiO2would have on sinter properties is complex, and not necessarily predictable. High concentrations of Al2O3in the sinter result in high concentrations of the SFCA phase, but with drastically deteriorated properties. This study also confirmed that the form in which fluxes are added to the raw material sinter mixture affects the mineralogy and properties of the produced sinter.

Jan 1, 2010

By Braam Blom

PK2 Ventilation shaft is part of Paardekraal No 2 twin shaft system that is being developed to replace depleting Merensky reef production at Paardekraal shaft complex. The sinking team at this shaft faced considerable challenge of improving the total sinking cycle in order to be able to deliver the fully equipped shaft on time and on schedule. The cladding support cycle was identified as the tedious and time consuming activity in the overall shaft sinking operation. Reduction in the time required for handling and setting up the support installation equipment, and the time required for subsequent installation of the necessary support has a direct impact on the overall cycle time, and consequently the overall productivity and efficiency of the sinking operation. This reduction in support cycle was achieved by making use of machine carousel. The objective of this paper is to describe the support methodology that was used during the ventilation shaft sinking and the use of the machine carousel to reduce the cladding support cycle. The machine carousel replaces the traditional use of machine kibble in conventional vertical shaft sinking and has been designed specifically for installation of sidewall support at the shaft bottom during the sinking process.

Jan 1, 2009

By R. Hope, C. van Heerden

In any process or organization inefficiencies are costly. In times of abundance this reality often does not receive much attention. During such times the focus is rather on increasing capacity to increase production. However, there is a growing awareness in the world of tougher economic, social as well as environmental conditions, and enterprises find themselves facing greater demands for accountability towards shareholders, the environment and the public, as well as growing competition for market share and limited global resources. This reality is no different in ensuring a sustainable mineral sands operation. In order to achieve this, any operation needs to be stripped of all process as well as operational inefficiencies. In this context it has become essential for any Mineral Separation Plant (MSP) to have the necessary process monitoring and control systems in place to continually monitor and optimize the production of on-spec products and maximize operational efficiency and consistency. The MSP Grade Control Solution developed by Crusader Systems and running on top of the CSense platform contributes towards these goals by improving the consistent production of on-grade product. This allows the process to operate closer to the maximum allowable product grade constraint, which in turn maximizes production.

Jan 1, 2003

By L. P. Lamprecht

Traditionally, South African shaft sinking operations have used electric detonators for the initiation of blastholes. Globally, the trend in shaft sinking is to use the shock tube and detonating cord (STDC) initiation system, with value adding benefits. In pursuing this global trend, Cementation Mining of South Africa in partnership with SMX have ventured the STDC route. This paper explores the work carried out to date, and identifies a number of benefits to be gained by using the system.

Jan 1, 1999

By M. van Biljon

The possible closure and subsequent flooding of South Deep Gold Mine?s neighbouring Randfontein Estates Limited No. 4 Shaft (REL 4) necessitated the construction of five concrete plugs in the connecting tunnels to prevent the ingress of groundwater into REL4 from flooding South Deep mine. Several technical investigations had been carried out before and during construction of the plugs in order to reduce the probability of groundwater flow through the boundary pillar between the two mines or through the rock mass immediately around the plugs. This paper describes the geological, hydrogeological and stability investigations carried out to evaluate the structural competence of the boundary pillar.

Jan 1, 2006

By M. Shapiro, L. A. le Grange, B. Henning

Effective pyrometallurgical process vessel design requires accurate assessment of the heat fluxes through the walls of the furnace. This is particularly important for freeze lining operation which is designed to protect refractory materials exposed to chemically corrosive molten contents, or facilitate high temperature operation when the refractory materials are used at conditions close to their service limits. Numerical modelling of fluid flow and heat transfer in process vessels is often used to aid in the design of process vessels. Sophisticated models are used to analyse the three dimensional flow and heat transfer predicting the effects of electrical heating, magnetic stirring, buoyancy, shear forces, various cooling effects and ultimately heat fluxes at the walls of the furnace and refractory. Traditionally these models are applied to the separate single fluid systems in a vessel such as the freeboard region including the arc, the slag region and the metal bath. Boundary conditions such as shear forces and heat fluxes between connecting regions such as the slag and metal bath are either estimated or carried over from separate solutions. Shortcomings in these traditional approaches include the estimation of sometimes critical boundary conditions leading to unreliable heat flux calculations. Also when boundary conditions are carried over between solutions, the process is difficult to set up, time-consuming and finally not fully coupled. In this paper the definition and results of a fully integrated numerical model of a complete arc furnace are presented. The most important mechanisms acting in an arc furnace were considered, including the fields of electrical potential, current, magnetism, momentum, heat transfer and radiation. Temperature dependant properties included electrical conductivity, density, viscosity, and thermal conductivity. The geometry consists of the freeboard, the arc, slag, metal baths and different refractory regions. Although the combined model of air, slag and metal would be defined as a multi-phase problem it is not solved as such. Instead the different fluids are separated by sets of special solid baffles. These baffles allow the implicit transfer of current, magnetism, heat transfer and shear forces between the different fluids and disallow mixing of the separate fluids. The strengths of the integrated model are threefold: Firstly, it provides robustness in defining the geometry and boundary conditions for the overall model. Secondly, it provides the capability to switch on and off individual mechanisms such as buoyancy, magnetic stirring and shear forces in order to observe their individual importance. Finally, it provides a useful tool in the design process through its ability to obtain results of parameter changes in short time scales.

Jan 1, 2004

Application of Gy?s formula is appropriate for calculation of the Fundamental Error (FE) prior to samples being collected at any stage of the minerals process, provided that sampling parameters K and a (alpha) have been determined by calibration of the ores. Two types of calibration procedure are well established in the industry, the Hetrogeneity test and the 32-piece sampling tree experiment. The sampling tree experiment uses the variance and average grade of metal analyses from four series of samples at different nominal fragment size, as the basic input data. Pierre Gy suggested the cube as an appropriate exponent of the nominal fragment size for use in his equation. More recent work suggests that this exponent is variable and characteristic of specific ores and therefore requires calibration. The method described here explains the experimental procedure of the calibration. It is then possible to calculate a sampling nomogram using the sampling parameters K and a. This allows the sampler to determine a suitable protocol for the sampling event that will ensure that the FE does not exceed a predetermined precision at any point in the sampling procedure.

Jan 1, 2007

By K. I. Afewu

A modified approach to the implementation of Gy?s sampling theory is discussed and used to design a procedure for sampling crushed gold ore feed to metallurgical process plants. The approach involves calibration of certain ore-specific parameters. These parameters were calibrated for two different crushed gold ores en route to grinding mills in process plants. The model predictions were compared with the predictions from Gy?s original model. Far smaller masses of samples are required by the modified model than by Gy?s model at the same relative variance. The representativeness of the sampling procedure if normally distributed errors are assumed was also calculated. These procedures and evaluations lead to significant savings on cost of handling and preparation of the samples and to a quantifiable degree of confidence in the analytical results for the process plant.

Jan 1, 1998

By J. Rivoirard

Historically, linear and lognormal krigings were first created to estimate the in situ mineral resources of blocks. Nonlinear geostatistics and indicator kriging were subsequently developed to evaluate also the portion recovered when applying a cut-off on selective mining units (SMUs) within blocks. In practice these methods are generally based either on the Gaussian model with a transformation generalizing the lognormal case or on the indicators above cut-offs. Very often the indicator approach is simplified by kriging separately each indicator, and when starting from a continuous variable, a practical advantage of the discretization into classes lies in the easy treatment of a zero effect and of the high values. However, a number of so-called isofactorial models have also been developed for a discrete or continuous variable, where the full cokriging of indicators (i.e. disjunctive kriging) simplifies to the separate kriging of factors. Moreover, these models are equipped with a change of support, allowing a consistent estimation of recoverable resources on SMUs. Min-Max Autocorrelation Factors (MAF) analysis of the indicators offers a new approach for indicator modelling. In particular the first factor, the one with the highest spatial continuity, can help in choosing the type of model. For example a monotonic experimental first factor can be used directly as the basis of a discrete diffusion model, unless a continuous diffusion model such as the Gaussian model can be used on the original variable. This approach is illustrated on a uranium deposit mined selectively: estimates of recoverable resources by discrete disjunctive kriging and uniform conditioning in a Gaussian model are compared locally to short-term estimates based on two areas densely drilled.

Jan 1, 2014

By F. Peer

This Technical Note was presented as a poster at the Western Cape Mineral Processing Symposium held in August 2001 The cleaning of fine coal (-1000 µm) in today?s coal preparation plants is an economically important factor. Coals with high ash contents are, in general, commercially undesirable. Current well-known techniques for treating fine coal include froth flotation and spirals. The primary critical factor with regards to spirals is the efficiency of the process whereas that of flotation, is the cost of there agents used. Research into enhanced gravity separation techniques has resulted in several commercially available enhanced gravity separators. This project was based on a preliminary investigation into the feasibility of one such separator, to effectively treat fine (-500 µm) coal. Experimental variables included particle size and speed of rotation of the said instrument. The performance of the separator was compared to the results obtained from liquid density separations done for the two coal fractions evaluated. From the results obtained in this preliminary study it appears that the piece of equipment investigated does not measure up to expectations. Recommendations for further investigation include the evaluation of the instrument on other South African coals to obtain conclusive results.

Jan 1, 2002

By J. Forwood

The Youga gold mine in Burkina Faso, West Africa, is scheduled to produce first gold in the third quarter of calendar 2007. The project is expected to produce 540 000 oz of gold over 6.5 years, from a conventional open pit carbon in leach mine. The direct capital cost of the project is US$47 M. Etruscan Resources Inc, a Canadian based gold exploration and development company, holds 90 per cent of the project company Burkina Mining Company SA (BMC). The state of Burkina Faso is free-carried for the remaining ten per cent of BMC. RMB Resources Limited, of Melbourne Australia, has arranged a US$35 M project finance facility for BMC (the Borrower) as the majority of funding for the Youga project development. The loan facility was provided by RMB Australia Holdings and Macquarie Bank Ltd (the Lenders) each as to 50 per cent in the lending syndicate. The Lenders also provided a gold hedging facility to guarantee a minimum price for the project's gold production. Burkina Faso is a francophone country, part of the Economic and Monetary Union of West Africa (UEMOA). The project financing is the first such facility to be arranged for a mining project in Burkina Faso, with little or no precedent available in other UEMOA countries. Therefore, while the Youga gold project is forecast to be a robust project applying conventional mining and processing methods, a number of legal, technical, commercial and social issues required identification, evaluation and resolution before the loan could be established. This paper describes that evaluation process and the resolution of these issues. In-house experience and expertise in both the Lenders' and Borrower's teams has facilitated a greater understanding and `ownership' of the issues and hence provided comfort with risks which might not normally be taken in conventional project developments and project financings. As a result, blanket external reviews were not required by the Lenders. A long-standing relationship between Etruscan and RMB Resources also facilitated solutions to a number of issues. Nevertheless, a degree of flexibility by the Lenders, the Borrower and Etruscan was required to successfully close the financing.

Jan 1, 2007

By A. D. Thomas

Some years ago, the authors developed an analysis of non-Newtonian pipe flow based on enhanced turbulent microscale and associated sublayer thickening. This analysis, which can be used for various rheologic modelling equations, has in the past been applied to smooth-walled pipes. The present paper extends the analysis to rough walls, using the popular Bingham plastic equation as a representative rheological behaviour in order to prepare friction-factor plots for comparison with measured results. The conditions for laminar-turbulent transition for both smooth and rough walls are also considered, and comparisons are made with earlier correlations and with experimental data.

Jan 1, 2007

By H. J. Ilgner

The paper reviews the results to date of an integrated research programme currently being conducted by CSIR Mining Technology, aimed at impacting significantly on concentrated mining with face advance rates of up to 20 times faster than presently achieved. Consideration is given to the interplay between innovative technologies for continuous non-explosive mining or rock comminution underground and lateral hydraulic transportation in cross cuts, haulages and eventually hydro hoisting. Novel technologies for underground comminution of reef and development waste and an innovative pumping system suitable for the hydraulic transportation of coarse comminuted rock are reviewed. Emphasis is placed on South African gold mine reef and waste samples comminuted by electric shock wave comminution technology. The innovative TORE® pump system appears to be well suited for the successful hydraulic transportation of rock, produced by electric shock wave comminution, at solids concentrations between 45 % and 67 % by mass.

Jan 1, 1997

As part of a comprehensive risk analysis which was carried out into the effectiveness of the water barrier between South Deep and Randfontein Estate mines, the potential threat posed by large seismic events was assessed. The study covered several aspects. Firstly, an estimate of the maximum credible earthquake was obtained from a probabilistic analysis of the regional seismicity of the previous 25 years. Allowance was made for ?reservoir-induced? effects by increasing the estimate of the size of the maximum credible earthquake from ML= 5.1 to ML= 5.5. Based on available knowledge of the geological structure, the possibility of such an event occurring in the vicinity of the barrier pillar was estimated. The possibility of substantial damage to the barrier rock mass, resulting as a consequence of a large event, was assessed. The likely damage to the concrete control plugs installed in five tunnels that penetrated the barrier, which might result from a ?near-miss? by the largest possible seismic event or from a ?direct hit? by a smaller event, was also considered. It was concluded that there was a negligibly small possibility that the maximum credible earthquake could occur close enough to the barrier, and in such a manner, as to cause any damage to it or to the plugs in the tunnels passing through it. The possibility of serious plug damage occurring as a result of a ?direct hit? by as maller event was slightly greater, but still sufficiently remote as to be of no practical concern at all.

Jan 1, 2006

By Q. G. Reynolds

DC arc furnaces are widely used for steel scrap melting, and are increasingly being used for smelting applications as well. The electrical resistivity of slags varies widely, from highly conductive slags in ilmenite smelting, to highly resistive slags in applications such as cobalt recovery from non-ferrous slags, and nickel laterite smelting. Models have been developed to predict the electrical behaviour of the DC open plasma arc and the molten slag bath. These models allow the voltage and current ranges of furnace power supplies to be specified.

Jan 1, 2004