Search Documents

By Stephen Krickovic

A methane emission rate study was conducted in 1969 on a longwall section of a Lower Kittanning coalbed mine in central Pennsylvania. The longwall face was mined with a drum shearer between developed headings on the head end and headings on the tail end that were driven with a ripper-type continuous miner as needed. The study was conducted over 22 consecutive shifts (7-1/3 days). The average methane emission rate from the Lower Kittanning coalbed during mining at the face and developing the headings at the tail end of the face was 34 Am. Caving of the gassy overlying strata as the result of mining at the face increased the methane emission to rates ranging from 702 to 1,049 cfm.

Jan 1, 1971

By Noel N. Moebs

The Bureau of Mines measured surface subsidence above four small coal mine room-and-pillar sections in southwestern Pennsylvania, to obtain preliminary information on the magnitude and character of selected parameters, such as angle of draw and maximum subsidence, which are essential to the development of subsidence prediction methods. Data varied widely at the four sites; this is attributed to local geologic and mining conditions. Surface deformation at each site was of a magnitude normally associated with severe structural damage.

Jan 1, 1982

By Rex D. Thomas

Concentration of the kerogen (organic material) in oil shale was accomplished by centrifuging after pretreating the oil shale with carbonic acid to remove the carbonates and pretreatment with sodium hydroxide (pH 11.5) to remove the claylike minerals. Analysis of the materials obtained showed that the concentrations of organic sulfur and organic nitrogen compounds were not affected by centrifuging. These compounds are evenly distributed in the kerogen and are not strongly bound to the mineral constituents. Organic oxygen compounds, however, were concentrated in the light fraction. These compounds are more closely associated with the kerogen and are not bound to the mineral constituents. Iron compounds other than pyrite apparently are closely associated with the organic material.

Jan 1, 1970

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

1. Introduction This document represents Part II of our final report on the development of a "Remote Sealing System for Extinguishing Coal Mine Fires. " It is a technical report which summarizes the results of system development and field demonstration. Part I of this two - part final report is an Operator's Manual for the application of the Remote Sealing System to a coal mine fire. 1.1 Background When coal mine fires go out of control and can no longer be fought directly, the standard fire fighting technique is to construct air-tight seals in the mine passages leading to the fire area so'--,that the oxygen supply to the fire is". cut off. Ultimately, it is desirable to isolate the fire zone in such a way that normal operations can resume in the remainder of the mine. The construction of seals in the- mine causes the atmosphere to pass through a toxic and explosive phase. Explosions, if they occur, are not only hazardous to the men working at the sealing operation, but can also undo much of the sealing work which has already been accomplished. Sealing of passageways surrounding the fire zone from within the mine is extremely difficult and dangerous. Methods for direct sealing are detailed in "Control of Mine Fires'. 1 An alternative to this approach is the technique of remote sealing. This involves drilling boreholes which intersect the mine passages at the locations where the desired seals are to be constructed. The seals are then constructed by pouring material down the borehole and filling a segment of the passage from bottom to top. During this operation, there are no personnel in the mine, all operations taking place on the ground surface.

Jan 1, 1973

Provide an environmentally compatible means of producing lead from galena concentrates that replaces the current high-temperature pyrometallurgical primary lead smelting process and supplies pure lead metal within present and proposed Environmental Protection Agency (FPA) and Occupational Safety and Health Administration (OSHA) lead emission standards. Approach The U.S. Bureau of Mines developed an energy efficient and pollution-free leach-electrowinning method for use in recovering pure lead metal and byproducts from lead sulfide concentrates.

Jan 1, 1989

By R. V. Lundquist

Past reports by the Bureau of Mines have described the extraction of alumina from numerous aluminum silicate materials by the lime-soda sinter process. The results from pilot-plant investigations of six materials, with alumina-to-silica mole ratios from 0.3 to 8.7, indicated a relationship between the alumina-silica ratios and the processing characteristics of the sinter. A series of laboratory tests was conducted to define this relationship. Sinter and leach tests determined that an alumina-to-silica mole ratio of 0.90 or greater resulted in the best alumina and soda recoveries while leaving the leach slurries practically free from any tendency toward gelation. The widely different chemical and mineralogic properties of the various aluminous materials used in compounding the mixes had no perceptible effect on the leaching characteristics of the sinter. The blending of low-cost, high-alumina materials with aluminum silicate materials to give an alumina-to-silica mole ratio of 0.90 or greater would improve alumina and soda extraction and minimize operating problems in the lime-soda sinter process.

Jan 1, 1970

By C. H. Schwartz

A thermal radiation probe was constructed and tested in pulverized-coal-fired furnaces. A rotatable sensing head on the side of a water-cooled probe permitted measurement of radiant flux within a 7.20 cone from any desired direction to a point within a furnace. A response curve for a corner-fired furnace showed radiant flux of 130,000 Btu per sq ft per hr, when viewing flame, and 60,000 Btu per sq ft per hr, when sensing wall reflection. Detailed drawings and fabrication procedure are given.

Jan 1, 1970

Develop a safe, nonpolluting power source for underground mining equipment. Approach The Bureau of Mines and EIM-CO Mining Machinery International entered into a cost-shared project to develop and demonstrate a novel power source for mining. An underground mining utility truck was equipped with an ultra-low-emission hydrogen-fueled engine and a safe, metal hydride fuel storage system. How It Works The nonpolluting hydrogen engine and a "solid-state" (metal hyride) hydrogen fuel storage system were combined to power a utility mining vehicle. An 85 horsepower diesel engine was convened to burn hydrogen. The engine was converted by equipping it with a spark ignition, lowering the compression ratio, turbocharging, and adding an ahercooler and a parallel fuel induction system. Parallel induction provides two intake paths, one for hydrogen and one for air. It avoids intake-manifold backfiring by keeping the hydrogen and air separate until they enter the cylinder.

Jan 1, 1986

By Forrest T. Moyer

The safety record of the mineral and mineral-fuel mining and processing industries in 1965 was improved slightly, as indicated by the reduced injury-frequency and severity rates. The overall operating activity was higher in 1965 as measured by the gains in the number of men working and in the total man-hours of worktime. Injury Experience.-The rate of occurrence of all disabling work injuries in the mineral industries was 17.65 per million man-hours in 1965. This overall rate comprised frequencies of 0.28 for fatal and 17.37 for nonfatal work injuries, of which both were slightly better than the corresponding rates of 0.29 and 17.53 in 1964. Fatalities totaled 537; 5 less than in 1964. However, the total of 32,982 nonfatal injuries was 575 higher than in 1964. This larger number of nonfatal disabilities was offset by the increased worktime so that the nonfatal frequency rate decreased in 1965.

Jan 1, 1967

By Jack E. Fraley

Poor lubrication reduces the life of wire hoist ropes when they are used in corrosive environments. Although lubricants are added to ropes during the manufacturing process, these lubricants can deteriorate during use, and it is often necessary to add more lubricant to both the interior and exterior of the rope while it is in service. The U.S. Bureau of Mines evaluated the effectiveness of synthetic lubricants, using electromagnetic nondestructive testing (NDT) to measure deterioration in ropes while they were in service. For nonpressurized lubricant applications, synthetic lubricants appear superior to petroleum-based lubricants in their ability to penetrate to the interior of a rope. Therefore, the synthetics offer better wear and corrosion protection.

Jan 1, 1990

By Doris M. Hyde

New mineral activity focused on increased petroleum exploration activities, while the established construction-oriented minerals sector operated without substantial change from previous years. After showing a 1 % real growth in the $154 million II gross domestic product (GDP) for 1983, preliminary estimates for 1984 indicated that the same growth pattern prevailed. The negative trade balance at midyear had worsened over the negative balance for the same period in 1983. An upward trend in import costs partly reflected the impact of Mexican inflation, which made that country's goods more ex-pensive and led to increased imports from North America and Europe. On the other hand, by midyear, the reexport trade with Mexico indicated an upward climb from the 1988 low of $12.7 million.

Jan 1, 1986

By J. M. Singer

Approximate equations were used to compute the radiant heating of float coal dust by approaching flames for various combinations of particle size, dust path length (flame travel distance), flame temperature, dust concentration, flame speed, and flame length. The computed values of degree of radiant heating and flame travel distance for preheating the coal dust should be useful for estimating the increased fire hazard of different coal dust-flame parameters. Some findings relating to coal mine disaster control are-- 1. Coal dust clouds cannot be preheated to ignition temperatures by flame radiation alone when deflagration speeds are greater than about 10 m/sec. Thus it appears unlikely that radiation alone will cause flames propagating in dust clouds to accelerate to detonation velocities. 2. Small particles in the radiation flame zone caused by burnout and soot formation increase the degree of preheat significantly. 3. The concentration of float coal dust (radii = 3 to 40 microns) for maximum radiant heating usually peaks in the range 50 to 200 mg/liter of air.

Jan 1, 1970

By Richard J. Mainiero, Sapko, Marcia L. Harris

Since 1988, there have been thirteen documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through near surface strata into structures or other enclosed spaces as a result of nearby trench blasting or surface mine blasting. From these incidents, there are thirty suspected or medically verified CO poisonings and one fatality associated with these incidents. To better understand the variables contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out a small-scale field study to identify key factors that may contribute to the migration of CO through the ground. NIOSH conducted single-hole heavily confined experimental test shots to measure the radial pressure pulse as it propagated through surrounding monitoring holes to determine if a relationship existed between the pressure pulse and resulting CO measurements afterwards. NIOSH also monitored blasts at an airport construction site. Following the detonations, the concentrations of CO, nitric oxide (NO), and nitrogen dioxide (NO2) were monitored for several days in the surrounding satellite holes. The peak CO measurements relative to distances from the shots were compared. Pressure histories and peak particle velocities (PPV) were measured at monitoring boreholes. It was found that the differential pressures recorded within the boreholes give some indication as to the likelihood of CO appearing, whereas the PPV measurements do not seem to be as good an indicator for potential CO migration. In this limited study, changes in barometric pressure had very little influence on removing the trapped detonation products, whereas applying a vacuum to the monitoring holes was effective in reducing the entrapped CO concentration.

By A. R. Rule

Research was conducted by the Bureau of Mines to develop a process for utilization of Idaho kyanite. A continuous gravity-flotation separation process was applied successfully to recover kyanite-group minerals from an Idaho ore containing about 21 percent combined kyanite, andalusite, and sillimanite. Dry magnetic separation of the concentrate resulted in a product containing about 90 percent kyanite at a recovery of 63 percent of the kyanite-group minerals in the ore, Alumina and silica analyses were within the range generally accepted for conversion to mullite, and the finished products had a pyrometric cone equivalent of more than 38. A recovered garnet coproduct may be of commercial value.

Jan 1, 1973

By J. A. Organiscak

Two types of airflow splitting methods for improving longwall dust control were investigated by NIOSH's Pittsburgh Research Laboratory. These methods included a translucent mesh barrier and a staged spray barrier system to confine the shearer-generated dust to the coal extraction side of the longwall face while maintaining a cleaner split of airflow on the opposing worker walkway side of the longwall face. The translucent mesh barrier was shown to provide notable dust control effectiveness up to 60 m downstream of the shearer in both the laboratory experiments and a longwall field evaluation, provided the mesh barrier remains relatively parallel to the airflow. The staged spray barrier system showed marginal dust control effectiveness in the laboratory and subsequently was not field tested.

By T. G. Carnahan

The Bureau of Mines conducted laboratory-scale weathering research on a leach residue containing elemental sulfur and mixed metal sulfides. Experiments were performed to determine pH and impurity element concentrations in the effluents as functions of time and to determine the effects on effluent concentrations of mixing the residue with dolomite tailing material. Four 800-day tests were conducted simultaneously. Soluble metal concentrations, especially zinc and copper, were excessive in the effluents from washed and unwashed samples of the residue. Concentrations of up to 20 g/l of Zn and 12 g/l of Cu were obtained. The pH values of the unwashed and washed residue effluents at the completion of the experiments were 2.8 and 1.9, respectively. Sulfuric acid from oxidation of pyrite caused the pH decrease. Mixing unwashed residue with dolomite tailing to maintain a near-neutral pH minimized the heavy metals content in the effluents. The pH in the dolomite tests increased slowly after the first 360 days and attained values of 7.8 and 8.2, respectively, for tailing containing 1 pct leach residue and for tailing devoid of leach residue. Dissolved zinc and copper did not exceed 0.10 g/l of Zn and 0.001 g/l of Cu.

Jan 1, 1982

By Travis Q. Lyday

The Other South Pacific Island states extend from Palau, also called Belau, near the Philippines in the west, to French Polynesia in the east. However, a number of countries and territories have been omitted, from this chapter because their mineral production was insignificant to the local economy. These include the French over-seas territories of French Polynesia and Wallis and Futuna Islands; independent states, including Kiribati, Marshall Islands, Micronesia, Palau, Tonga, Tuvalu, and Vanuatu; the New Zealand freely associated state of the Cook Islands, and the New Zealand dependency of Niue. What mineral production existed in these islands was limited to construction materials such as coral reef limestone, crushed stone, and sand and gravel in minor quantities solely for domestic consumption. FIJI The mineral industry of Fiji continued to be dominated by gold, although this sector contributed less than 1 % to the gross domestic product (GDP) of the country. Gold and silver together ranked second in value among the country's exports. Fiji's economy contracted 11% during the 8-month period following the first, on May 14, of two military coups. Although the island nation had been a member of the British Commonwealth of Nations since its independence on October 10, 1970, Fiji's membership terminated with the emergence of the Republic or Fiji on October 15.

Jan 1, 1989

By Ann G. Kim

The Bureau of Mines investigated factors that influence the formation of methane and other hydrocarbon gases in coal, which is an integral part of the coalification process. Coalification begins with a biogenetic stage in which plant debris decomposes and peat is formed; methane and CO2 are the predominant gases produced during this stage. During the diagenetic stage of coalification hydrogen and the hydrocarbon gases methane, ethane, ethylene, propane, propylene, butene, iso-and normal butane, and pentane are formed by dissociation of the organic material. Methane may also be produced by a secondary reaction of hydrogen with unsaturates or by the reduction of CO2. The gas contained in coalbeds is a mixture of methane, C2 through C5 alkanes, CO2, O2, N2, H2, and He; its heating value is equivalent to that of natural gas. The gas content of coal depends on many variables, but an empirical relationship between adsorptive capacity, rank, and depth has been observed.

Jan 1, 1978

By W. E. Lamont

The Bureau of Mines studied the potential for recovering marketable barite concentrates that meet oil well drilling-mud specifications from barite waste pond materials. The study was conducted as part of the Bureau's research program to conserve domestic mineral resources by advancing mineral recycling technology. The samples, which were obtained from Georgia, Nevada, Missouri, and Illinois, varied widely in character, particle size, and barite content. The samples were treated with sodium silicate and sodium cetyl-stearyl sulfate and then floated. The flotation flow sheet was modified to reject barren coarse and/or slime fractions from some of the samples, and one feed sample had to be scrubbed prior to flotation to remove residual flotation reagents. The cleaned concentrates had BaS04 contents ranging from 95.0 to 96.9 percent, while recovering 81.2 to 95.9 percent of the barite in the feed. The specific gravity of each concentrate exceeded the specification of 4.2. The removal of the flotation reagents from the flotation concentrate was not investigated.

Jan 1, 1982

By Eugene Baker, Joseph Cervik, Albert Sainato

In Europe, water infusion is used widely to reduce generation of respirable dust during mining. Its use in the United States is limited to a few plow operations in the Pocahontas No. 3 Coalbed. This Bureau of Mines report describes the technology for infusing water in to a longwall panel and reports the results of a recent demonstration in the Lower Sunnyside Coalbed that achieved dust reductions averaging 58 pct. Because water infusion increases moisture content of the coalbed, face air velocities in excess of 500 ft/min (2.5 m/s) are possible, further diluting dust levels before dust entrainment occurs. An economic analysis shows a 23-pct reduction in operating costs when coal production is increased by changing from unidirectional mining to bidirectional mining with water infusion.

Jan 1, 1983