Search Documents

By Thomas P. Mucho, Dennis Dolinar, Christopher Mark

During the 1990s, the former U.S. Bureau of Mines conducted a number of field studies in which the performance of different types of roof bolts were evaluated in different geologic environments. The studies used a standard suite of measurements, including multipoint extensometers, strain-gauged roof bolts, and roof bolt load cells. The sites were chosen to investigate the effect of a variety of parameters, including installed tension, bolt capacity, grout annulus, and horizontal stress orientation. Although not fully successful, the measurements provided valuable insights into each of these issues. They also showed that instrumentation and monitoring have important advantages over observational methods for comparing the performance of different roof bolting systems.

Jan 10, 2000

By John R. M. Hill

The Bureau of Mines performed elastic-plastic, finite-element analyses to investigate the support performance of hydraulic backfill. A mathematical model was developed for two vertically adjacent stopes separated by a sill pillar. An exact duplicate of a working stope was not intended; however, the model did simulate a working stope to the extent that field measurements from an active stope could be used for comparative purposes. Using a predetermined mining sequence, the computer analysis simulated the mining operation as a series of incremental cut-and-fill steps. Computer results included a complete history of stope closure and pillar stresses throughout the mining sequence. With the mining sequence and rock properties held constant, three separate analyses were made using varying backfill properties. These cases included no fill,-low-to-medium-quality fill, and medium-to-high-quality fill. Results of these analyses show decreases in stope closure and pillar stresses as the backfill quality increases, thus reducing the possible occurrence of rock bursts. Predicted stresses within the backfill compare favorably with field measurements. A relationship between maximum stress normal to the stope wall and the ratio of relative fill stiffness to relative rock stiffness was also indicated.

Jan 1, 1974

By Stephen W. Lambert, Michael A. Trevits

The Bureau of Mines examined the wellbore of a vertical gas drainage well in the Mary Lee coalbed to determine the results of specific completion procedures in coal. A jet-slotting tool was used to cut four vertical slots through the casing about 1 ft below the coalbed. Even though stimulation treatment pressure was excessive, hydraulically induced channels were contained entirely within the target coal zone. Sand-filled, induced channels were horizontal, inclined, and vertical, and were propagated in directions similar to bedding planes, rock joint, and coal cleat directions measured in the mine. Variable gas flow rates, recorded during the productive life of the well, were attributed to chronic downhole pump malfunction and the slotted casing below the production zone.

Jan 1, 1978

By Thomas E. Marshall, Roy H. Grau

The U.S. Bureau of Mines has developed an acoustic test for determining if a rock salt sample is from a "normal" nongassy salt face or from a gassy face where an outburst has the potential to occur. The test is based on the observation that a salt sample taken near an outburst-prone zone produces an audible popping sound when it is dissolved in water. The sound is produced when pressurized gas that is trapped in salt samples is released. In the acoustic test, the sound is electronically measured, digitized, and transmitted to a microcomputer; the output is an average decibel value that classifies the sample as "normal" or "outburst." The acoustic test procedure and equipment are described, and raw test results and data analysis are shown. Results are also shown for several salt samples that were analyzed using a laser Raman microprobe.

Jan 1, 1990

Objective To develop and evaluate the effectiveness of safety training tools specific to the underground hard-rock mining industry. Background Scaling, the removal of loose rock from the roofs and walls of a mine by manual or mechanized means, may be necessary during any stage of mining. Manual scaling is very labor intensive, and mechanical methods can be too powerful and actually produce a less stable roof.

Jan 1, 2001

By George S. Koch

The distribution of gold in part of the Getchell mine, Humboldt County, Nev., is presented through the statistical analysis of 956 assays of rock cuttings from wagon-drill holes. Two methods to predict grade in undeveloped parts of the ore body are evaluated, and the possibility of sampling bias is tested. The distribution of gold is compared with that in three other Nevada gold deposits of the same type characterized by gold particles mostly of submicron size associated with carbonaceous rocks, and also with that in deposits with coarse-grained gold. Usually, fewer samples of a given type are required to make a satisfactory grade estimate for submicron deposits than for coarse-grained deposits. The economic consequence is that submicron gold deposits are likely to be less expensive to sample and evaluate than coarse-grained deposits.

Jan 1, 1970

By T. F. Tomb

This paper describes field and laboratory investigations conducted on a dust-collection system recently designed for integral use with a continuous mining machine. The results of the field study showed that the average respirable dust concentration measured at the machine operator's position was reduced by about 60 percent (from 8.7 to 3.5 milligrams per cubic meter), and total and respirable dust concentrations in the return air were reduced by approximately 70 percent. The data indicated that approximately 20 percent of the dust generated at the face was not passed through the scrubber. The lab-oratory results showed that the overall efficiency (by particle count) was approximately 80 percent for total dust concentrations (minus 20 micrometers in size) typical of those encountered underground. Calculations based on total dust concentrations measured during the underground study indicated that the respirable mass concentrations of the effluent from the scrubber would still exceed acceptable levels even if scrubbing of all the air at the face were possible.

Jan 1, 1973

By Peter F. Steidl

As part of the Bureau of Mines methane control program, the Upper Free-port coalbed was studied in Fayette County, Pa., where this coalbed lies about 650 feet below the Pittsburgh coalbed and contains the largest remaining reserves of any coalbed in the county. Its estimated recoverable reserves in Fayette County are between 670 and 800 million tons. Coal and overburden isopachs, structure and joint pattern maps, and a fence diagram were prepared using data from gas and oil exploration logs and coal outcrops. These maps will aid in determining the need and/or feasibility of degasifying the Upper Freeport coalbed in the study area. Much of the coalbed in this area is under 600 to 1,400 feet of overburden. By correlation with data from the Pittsburgh coalbed, the gas content at depths of this order is estimated to be between 140 to 300 cf/ton of coal.

Jan 1, 1977

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX A - PNEUMATIC TRANSPORT OF FLY ASH 1. Introduction Two types of pneumatic transport of fly ash are critical to the success of (1) Transport of fly ash from the fly ash truck to the entrance to the borehole. Depending on the surface topography, this may be horizontal, decential and ascential. (2) Vertical downflow of fly ash through the borehole. All fly ash trucks have limited pressure with which they can pump the fly ash. Thus, the pressure drop in the fly ash hose will define the maximum length for pumping and consequently the maximum distance that the fly ash truck can be parked from the auxiliary blower. The same relationships describe the flow of the dilute fly ash-air mixture produced by mixing with the auxiliary air from the blower and thus define the selection of the pipe diameter. These are im¬portant considerations in the proper selection of the location of the passages to be sealed and the type of surface preparation required. The flow characteristics of fly ash down the borehole determine the selection of the minimum borehole diameter and the blower pressure. This appendix presents theoretical analyses of these flow regimes and summarizes the limited experimental data obtained during the field tests at Grant Town, described in Section 8.4. The analysis for the borehole flow is presented first as it is of greater interest to the program. This is followed by a discussion of the horizontal flow.

Jan 1, 1973

By J. L. Konchesky

The Bureau of Mines investigated the main reactions of coal gasification by steam. Coal (minus 70 mesh)-water slurry was fed into a laboratory-scale tube-coil gasifier to show the effects of residence time (0.6 to 1.1 sec), steam-coal ratio (2 to 11 lb/lb), and temperature (1,600° to 1,900° F), at about 1-1/2 atm. Devolatilization was very rapid: about 70 pet of the coal's volatile matter evolved within 0.6 sec at about 1,600° F; temperature increase released more volatile matter until about 95 pct was driven off at 1,900° F. Devolatilization was not increased by raising steam concentrations and was only slightly increased by extending residence time. Below 1,600° F, there was no evidence of the steam-carbon reaction, but at 1,900° F more than 80 pct of the coal's fixed carbon was converted to gas; the conversion was increased Significantly by increased residence time and steam concentration. The water-gas shift reaction occurred simultaneously with devolatilization, and the steam-carbon reaction, approaching equilibrium with increased residence time and temperature and decreased steam concentration.

Jan 1, 1969

By Marvin L. Whisman

A radiotracer technique developed by the Bureau of Mines extends to the parts-per-billion range the sensitivity for determining contributors of deposits formed in stored and thermally stressed jet fuels. The method depends upon measuring radioactivity associated with thermally induced deposits from fuels containing one labeled compound. The technique was applied to 88 test blends, representing 12 fuels and nine carbon-l4 labeled fuel constituents or fuel additives, or both. Data from results of these tests are included in this report. With this radiotracer technique, the contribution of fuel components and additives to thermally induced deposits in a variety of fuel environments was estimated before and after storage.

Jan 1, 1969

By Theodore Christos

The Bureau of Mines sponsored an investigation of the thermal oxidative degradation characteristics of certain solvents and hydraulic fluids used in underground mining operations. The following halogenated solvents were studied in view of their usefulness and their flame retardant property: tetrachloroethylene, C12C = CC12; 1, 1, 2-trichloroethane, CIH2CCHC12: and trichloroethylene, C12C = CHC1. The hydraulic fluids studied were representative of five groups approved by the Mine Safety and Health Administration for underground operation, namely: glycol-water solutions, mineral oil-water emulsions, synthetics other than phosphate esters, synthetic phosphate esters, and mixtures of phosphate esters with mineral oils and other ingredients. It was observed that the partially halogenated solvents present a greater potential toxic hazard than the fully halogenated materials, due not only to the easy production of hydrogen chloride but also to their ease of oxidation leading to the formation of phosgene and carbon monoxide. The pure phosphate esters exhibited the best thermal oxidative stability of the five groups of hydraulic fluids tested. A fluid containing phosphate esters mixed with mineral oils and other unidentified ingredients appeared to be the most hazardous On the basis that it produced very toxic acrolein and phosphine.

Jan 1, 1980

By D. E. Hirsch

A systematic procedure for separation, characterization, and semiquantitative analysis of high-boiling petroleum distillates was developed by the Bureau of Mines and applied to a 370° to 535° C distillate of Wilmington, Calif., crude oil. Separation procedures employed were isothermal and molecular distillation, chemical treatment, silica-alumina adsorption, and gel permeation chromatography. Characterization and analysis were accomplished by gel permeation chromatography correlations and mass and nuclear magnetic resonance spectrometry. These data should be useful in improving petroleum processing and utilization and in achieving the energy conservation inherent therein.

Jan 1, 1974

By Bruce T. Olenchuk, Wils L. Cooley

Electrical grounding is essential for the safe operation of power systems. A low-impedance path to ground is necessary to prevent the possibility of dangerously high potentials in human work areas. If for any reason this ground connection becomes faulty, a serious hazard may exist. One reason for faulty ground connections is ground bed corrosion. Corrosion of electrical ground rods has plagued the power industry and appeared in coal mine power systems. This paper will investigate ground rod corrosion, its cause, and possible solutions. Included is an evaluation of various ground rods for their ability to resist corrosion under stray current conditions. -The first known study of X-it3 Rod Corrosion is also presented.

Jan 1, 1979

By Gregory J. Chekan

In order to reduce waste and improve resource conservation, mine planning, and development, the U.S. Bureau of Mines is investigating multiple seam interactions associated with longwall mining. Longwall gate entry and panel stability have been influenced by previous mining in coalbeds above and below a mine in Virginia that operates in the Lower Banner Coalbed. Directly superjacent, approximately 115 ft, the Upper Banner Coalbed has been partially worked by room-and-pillar mining. Directly subjacent, approximately 730 ft, the Tiller Coalbed has been worked by partial room-and-pillar retreat mining. The study mine has experienced problems during development of gate entries in areas of overmining and undermining. It is anticipated that stress fields associated with adjacent mining may further affect gate entry stability and face advancement during the extraction of the longwall panel. To assess overmining and undermining effects on ground stability, the Bureau gathered geotechnical information at the site. Headgate entries and pillars were instrumented and monitored to study loading behavior as the longwall face approached and passed potential problem areas. Measurements indicate that although increases in average pillar pressure were greater than predicted values, previous mining in adjacent coalbeds had little effect on headgate stability.

Jan 1, 1989

By Thomas E. Marshall, Timothy Batchler, Anthony T. Iannacchione

As the amount of new fractured surfaces or "damaged rock layers" within roof rock increases, the stability of the rock mass decreases. While direct measurements of this phenomenon are not easily made, there is good circumstantial evidence to support this hypothesis. For example, it is common to observe increased cracks or fractures in the immediate mine roof rock before a roof fall. Likewise, roof drill holes placed in areas that later fail often reveal increased numbers and/or separations of fractures within the rock column through time. And finally, the frequency of microseismic activity, representative of rock fracturing, increases before a roof fall. For this study, more than 700 microseismic emissions were collected from two underground limestone mine roof fall areas in southwestern Pennsylvania. Microseismic events were located and magnitudes determined using the moment magnitude technique. Moment magnitude is based on the event seismic moment, which is a measure of the seismic deformation. The amount of new fracture surface length was calculated based on the stored strain energy within the rock prior to fracture. In the two case studies presented, a significant amount of microseismic activity was observed as much as two days before the first signs of failure in the roof fall areas. Additionally, results from this analysis reveal much about the behavior of strata prone to failure and allows for the construction of hazard maps based on microseismic emissions. The potential use of this technique as a means of anticipating roof falls is analyzed and discussed.

By Robert L. Lagace, Alfred G. Emslie

This report presents a mathematical model for the propagation of UHF radio waves in the large cross-section tunnels of a room and pillar limestone mine, and describes the analysis of a small amount of propagation data obtained in a limestone mine. The model and analysis is based on the waveguide mode theory developed earlier for the transmission of UHF waves in coal mine tunnels, with allowance for propagation losses due to refraction into the tunnel walls, to scattering by wall roughness, and to long range random tilt of the walls. Propagation around corners and through pillars is also examined based on a ray theory approach, together with the beneficial effects of placing reflectors at intersections to significantly reduce corner losses. The theory is found to be in fair agreement with the data; however, additional in-mine measurements are needed to provide a more conclusive test of the model.

Jan 1, 1979

By Barbara J. Halpern

There?s no denying that mining is a male-dominated industry. Yet thanks to technologies developed over the last 20 years, societal changes in sex role stereotyping, individual determi­nation, and the willingness of companies to train women, there are no jobs in mining today where women are not represented. Women are drillers and electricians as well as drivers of heavy equipment and haulpack trucks. They perform jobs ranging from field exploration and metallurgy to clerical and janitorial and warehousing positions, from prospectors and underground blasters to geologists and land reclamation experts, from communicators to legal experts on mining law and more. The Women?s Mining Coalition, founded in 1994 to shepherd responsible legislative mining reform, estimates that 20 percent of the workers in the mining industry are women. Although women are concentrated in clerical and adminis­trative jobs, at least 10 percent are in non-traditional, hardhat jobs, claims the group. There are women in management, but the numbers in senior management remain small, especially in larger companies.

Feb 1, 1998

By B. W. Jong

The U.S. Bureau of Mines investigated anhydrous chlorination and caustic-acid leaching processes to recover Ni, Co, Mo, and W from waste hydroprocessing catalysts. In batch laboratory-scale equipment, the chlorination process extracted 61 to 99 pet of the metals. Final recovery was 65 to 99 pct. The caustic-acid leaching process extracted 81 to 98 pct of the metals. Final recovery was 36 to 99 pct. Chlorination processing included roasting, chlorination, hydrolysis of metal chlorides for recovering Mo or W, water leaching of Ni or Co from the spent charge, purification, and solvent extraction or precipitation of Ni or Co from the purified solutions. Caustic-acid leach processing included NaOH leaching, solvent extraction of Mo or W from the NaOH leach liquor, H2S04 leaching of the NaOH leach residue, purification, and solvent extraction or precipitation of Ni or Co from the purified solution. The estimated fixed capital cost for a commercial-scale plant processing 39,000 Ibid of waste Ni-Mo-AI catalyst was $8 million for the chlorination process and $9.6 million for the caustic-acid leaching process. The estimated operating cost was about $0.20 and $0.40 per pound of the waste catalyst, respectively, for the two processes.

Jan 1, 1989

By Ronald S. Conti

Fire is a major concern for those who work in underground mines. A mine fire can occur at anytime and often results in a partial or total evacuation of mine personnel and could result in the loss of lives. Therefore, having a workforce that is well trained to prevent, detect, and fight a fire is important. This paper focuses on responders’ preparedness for fire. Responders in this context are considered the entire workforce and are categorized as first, second, and sustained responders and evacuating miners. Quality training enhances ones awareness of mine fire hazards and promotes self-confidence in combating fires and responding to emergencies. Early warning systems and other escapeway aids such as a through-the-earth signaling and communication system, lasers and strobe lights are also addressed. The technological advancements that have been made can improve the state-of-preparedness for responders to underground emergencies and increase the chances of survival for escaping personnel.