Search Documents

Etching solutions containing hexavalent chromium ions (e.g., chromic acid) are used in brass finishing, printed circuit board etching, preparation of plastic for plating, anodizing, and various other industrial surface treatment operations. As the solutions are used, hexavalent chromium ions are reduced to their trivalent state, contaminants accumulate in the solution, and the effective acid concentration is reduced. When the etching rate becomes unsatisfactory for the particular operation, the solutions are discarded. This is a problem because the discarded solutions are pollutants, and because replacing the etching solution is expensive. The Bureau of Mines has developed a process for regenerating these spent solutions and returning them to the surface treatment operation without interrupting the etching process. An electrolysis cell containing anode and cathode compartments that are separated by permeable membranes, is used for regenerating the spent solutions. The spent chromic acid solution is fed to the anode compartment and sui (uric acid is circulated in the cathode compartment. Application of a steady electrical potential of a few volts dc across the electrodes causes the copper ions and other contaminants in the spent solution to migrate through the membrane to the cathode compartment where copper is plated onto the cathode. Zinc and the other contaminants remain in the sulfuric acid. At the same time, the complex, trivalent chromium ions in the spent solution are attracted to the anode where they are oxidized to their original hexavalent state. The regenerated solution in the anode compartment is then recycled back to the plant?s etching operation for reuse.

Jan 1, 1980

By Lucia Kuizon

In 1986 and 1987, at the request of the U.S. Forest Service, the U.S. Bureau of Mines studied the Diamond Peak area comprising 183,000 acres in the Challis and Targhee National Forests in order to evaluate its identified mineral resources. More than 3,000 mining claims were located in three mining districts between the years 1882 and 1986. Approximately 230 mining claims in and the 150 claims adjacent to the study area were current in 1986, when Bureau of Land Management mining records were researched for this study. A total of 1,270 samples were collected from these sites (30 were for alluvial placer). Results of the investigation help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Lead-, silver-, zinc-, copper-, and gold-bearing minerals occur as veins and replacement bodies in shear and fault zones in Precambrian and Paleozoic calcareous Sedimentary rocks that have been complexly folded and faulted. Total production from the three mining districts in the study area was more than 150,000 tons of ore between 1901 and 1982. Approximately 11,600 tons of subeconomic resources consisting of lead, silver, zinc and copper were identified within the area. Over 37,500 tons of lead and zinc subeconomic resources were identified just outside the area. In addition, lead-, silver-, and zinc-mineral resources were identified at 4 mines within 2 miles of the study area. Iron mineral resources were also identified just outside the area.

Jan 1, 1991

By William J. Campbell

The Federal Bureau of Mines provided five test materials--amosite, short-and long-fiber chrysotile, crocidolite, and nonfibrous tremo1ite--to the National Institute of Environmental Health Sciences (NIEHS) for studies on the biological effects of orally ingested asbestos-related materials. An inter-agency agreement between the Bureau and NIEHS made possible this program to characterize these test materials. The Bureau in turn received support through contracts with the Ontario Research Foundation for the milling of amosite and crocidolite, and with the University of Maryland for microscopic measurements. The five test materials, which were supplied in quantities of 960 to 1,200 pounds each, were characterized by chemical-instrumental analysis for elemental composition, surface area, density, X-ray diffraction, infrared spectroscopy, thermogravimetric analysis, mineralogy, and particle size analyses. Particle size distributions were emphasized because of the current theories relating adverse biological effects to length-width characteristics of durable elongated particles.

Jan 1, 1980

By T. F. Dumm, O. Trass, V. R. Koka, L. G. Austin

"The size distributions of carefully screened 2 size fractions of ground materials were determined using a Microtrac laser dif-fractometer. The size distributions were fitted to the empirical function P(x) = 1/[1 + (x50/x)1] where P(x) is cumulative mass fraction less than Microtrac size, x. The standard deviation of A for a 50 second test time was approximately 0.5, so that seventeen test times give a mean with an estimated error within t 0.25 (95% confidence level). Values of were 5.44, 4.82, 4.40 for a coal ground under different conditions, indicating statistically different shape distributions; the average value for mica was 2.91 owing to the high aspect ratio of the particles. The ratio of x50 to the geometric mean sieve size was 1.2 for the coal and 0.70 for mica.1 IntroductionKoka and Trass have presented evidence [1,2] that materials ground in the Szego mill [3] give different shapes depending on the milling conditions. The variations in shape were deduced qualitatively by viewing SEM photomicrographs of selected 1/2 screen fractions. This paper quantifies their observed differences in shape by using measurements of the size distributions of screen fractions examined in a laser diffractometer [4] (Microtrac, Model 7991). The basic concept is that particles of 'a given ""screen"" size will give a wider distribution of ""Microtrac"" size when the particles are flaky with high aspect ratios, and a narrower distribution when the particles approach the cubical and spherical geometries.2 TheoryAustin and Shah [5] have shown that coal screened within a 1. 1/2 upper-to-lower sieve size range will give rise to a much wider distribution of Microtrac size. They found that the screen interval of irregular fragments of comminuted coals or quartz gave Microtrac size distributions which could be described by the simple function"

Jan 1, 1988

By G. L. Cook

The design of a dual-inlet system for a Consolidated model 21-103C mass spectrometer is described in detail. The system permits both high-mass and low-mass samples to be run by using a single instrument. The difficulties of using a single instrument for both purposes are given and a method of minimizing these difficulties through the use of the present design is discussed, After examining the experience of five years of use, the conclusions are that the bimodal operation is practical and the low-mass analyses had nearly the same precision as before the modifications to the instrument were made. In 1951, O'Neal and Wier.5/ published the first description of the modifications made to a mass spectrometer so that the spectra of hydrocarbons with molecular weights up to 600 could be obtained. Further discussion of the equipment of O'Neal appeared in 1953.6/ Also, Brown, Melpolder, and Young7/ described a parallel inlet system designed to reduce sorption effects at room temperature.

Jan 1, 1960

By R. R. Hornor

BIBLIOGRAPHY OF ARTICLES RELATING TO THE PRESERVATION

Apr 1, 1922

By Robert W. Gordon

This report describes the results and conclusions of the further development of a lightweight probe drill for use in anthracite mines. Improvements to the drill previously developed under Contract H0282044 were made and tested at an Eastern Pennsylvania mine. These improvements were: 1. Better hole cleaning due to the development of an air-water mist flushing system. 2. The application of roof drill bits to allow drilling through rock seams and lenses. 3. The development of a quick coupling drill system which reduced total steel change time. 4. Adaptation of a swivel to the drill anchoring system which greatly reduced set-up time between holes. With these improvements the probe drill demonstrated its ability to drill the required 11 holes in one shift. It also gained miner acceptance as a viable underground working tool. The probe drill proved to meet all of the design requirements of portability, low weight drilling controllability, structural integrity and reliability. In addition to its ability to drill the required probe pattern, the probe drill has the capability of drilling long holes. By drilling several holes over 80 feet deep the probe drill has demonstrated a potential for use in robbing pillars and for methane drainage.

Jan 1, 1981

By R. S. Dean

A general survey of the metallurgical work of the U. S. Bureau of Mines has been given in an article in the Missouri School of Mines Alumnus, and a somewhat more detailed review of the bureau work on lead and zinc will be found in the Mining Congress Journal. C. C. Furnas has contributed one general mathematical article. Dean, R. S. U. S. Bureau of Mines. 4, 1930, pp. 7-8. Program of Metallurgical Investigations of the Missouri School of Mines Alumnus, vol. 4, No. Investigations of the U. S. Bureau of Mines on the Milling and Smelting of Lead and Zinc. Min. Cong. Jour., vol. 16, 1930, p. 799, 808. Furnas, C. c. Evaluation of the Modified Bessel Function of Am. Mathematical Monthly, vol. 37, the First Kind and Zeroth Order. No. 6, 1930, pp. 282-287.

Apr 1, 1931

By W. M. Weigel

"The use of sand for the filtration of municipal water supplies is comparatively recent use in this country, although at the present time, most cities of any size that draw their water supply from surface sources use sand filters in their purification system. Not only are sand filters employed to remove sediment and suspended matter, but they also take out most of the bacteria in the water.The first comprehensive research and study of sand for this purpose was probably that of Hazen for the Massachusetts Board of Health in 1891 and 1892, although sand filters had been employed for a considerable time before, specifications for filter sand drawn since then have been largely based on the results of Hazen's work,The general requirements for filter sand are more exacting than for any of the different kinds of sands, except the chemical specifications for glass sand. Filter sand must be uniform in size and within certain limiting sizes. In addition, it must be clean and free from clay and organic matter and of fairly high purity. Early investigations established the fact that an excess of fine materiel increased the friction and decreased the rate of flow through the filter, and that the size of the finer particles rather than the courser, determined the effective size. Also, that large grains tended to cause irregularities in flow in different parts of the bed. There is no requirement as to grain shapes, except that they be not flat or elongated, since, so far as known, either rounded or angular grains are equally efficient.Based on Hazen's investigations, two factors are quite generally used to control the average size and uniformity of size of the sand. These are defined as follows: The ""effective size"" of a sand is such that 10 per cent by weight of the seed is finer than this size, end 90 per cent is coarser. It is expressed in millimeters, The ""uniformity coefficient"" is defined as the ratio of the size of grain which has 60 per cent finer than this size to the size which has 10 per cent finer (the ""effective size""). It is evident that the smaller this coefficient, the more uniform is the seed. If all the grains were exactly the same size, the coefficient would be 1."

Jul 1, 1924

By Clinton C. Knox

During the latter part of 1943, a magnetometric survey was conducted by the Geophysical Division of the Bureau of Mines at the Mahopac magnetite mine, Putnam County, N. Y., in an endeavor to locate a segment of the ore body that reports state was cut off by a fault. The Mahopac mine was abandoned about 1895 after producing nearly 1,000,000 tons of high-grade magnetite iron ore. The results of the investigation indicate the termination of the ore body by "pinching", or a displacement of such magnitude as to place any extension at a considerable distance from the original are body. This report describes the work done on the project and presents the data obtained.

Jan 1, 1948

By D. A. Reynolds, L. P. Rockenbach

"The method of analyzing light oil for benzene is fully described by Fieldner and others 4/ and Kester and Kolmes 5/. In this procedure, benzene is determined by shaking 20 cc. of the 79º to 81º C. boiling point cut from the fractionation of the refined light oil with 3 volumes of 98—percent sulfuric acid in an A. S. T. M. separator funnel of the type used for determining water in bitumi¬nous materials. After the mixture has been shaken 5 minutes it is allowed to settle at least half an hour and the acid is drawn off; the residual oil is reported as paraffins and the decrease in volume as benzene. The method has been found satisfactory for light oils from coals carbonized at 5000, 600°, and 7000 C. but does not give accurate, reproducible results for oils from the 800° C. tests.The content of benzene of the 790 to 81° C. cut is high, 90 to 95 percent, for 800° C. light oils, whereas for lower—temperature light oils it is considerably less. Benzene is the most difficult of the aromatics to sulfonate, hence the acid concentration must be maintained above 95 percent to insure complete sulfonation. Sulfuric acid (98 percent) reacts with benzene, but its reaction with paraffins at ordinary temperatures is negligible; however, more concentrated acid will attack paraffins and give erroneous yields of benzene. The reaction between benzene and sulfuric acid forms water that will dilute the acid. The effect of this dilution may be overcome by increasing the acid-to-oil ratio or increasing the strength of the acid. The latter, however, must not be used, because the stronger acid reacts with paraffins."

Mar 1, 1942

By H. B. Brunot

A complete list of permissible mine equipment, tested and approved by the Bureau of Mines previous to January 1, 1947, was published as Information Circular 7432.2/ A list of permissible mine equipment tested and approved by the Bureau of Mines during the calendar years 1947, 1948, and 1949 was published as Information Circular 7569. The present list supplements Information Circulars 7432 and 7569 and includes all of 'the equipment approved during the calendar year 1950. Information Circular 7465, which included a list of permissible mine equipment tested and approved by the Bureau of Mines during the calendar year 1947 therefore is superseded.

Jan 1, 1951

By E. L. Sweeney

The mine and mill of the Davis-Dunkirk Lines, Inc., are about 16 miles by road south of Prescott, Ariz., which is the nearest railroad point for receiving mine and mill supplies and for shipping concentrates to smelters. A good trucking road reaches within 2 miles off the property, but from that point the grade is very steep. Outgoing loads are limited to 2 tons. The topography near the mine is exceedingly rugged, and the area is slightly wooded. The climate is mild excepting in a few winter months, when the snowfall is heavy. Electric power is secured by way of a 4 1/2-mile, high-tension line connecting with the main line of the Arizona Power Co. The concentrator was intended to treat 60 tons or more daily of gold-silver-copper ore and make a single gold-silver-copper concentrate for shipment to a copper smelter.

Jan 1, 1933

By Frank J. Wiebelt

The Mohawk lead-zinc mining in San Bernardino County, Calif., was examined by D. W. Butnor, an engineer or the Bureau of Mines, at the request of Dunton, Ray, and Greenwood, leaseholders. Current operations were on a marginal economic basis, and government aid was sought in an endeavor to outline ore reserves so that production might be maintained.

Jan 1, 1949

By Lung Cheng

The Bureau of Mines has installed passive water explosion barriers in two operating mines to determine their usefulness in U.S. coal mines. The primary objective of this field trial was to determine the effect of the explosion barriers on mining operations. Data were also obtained on the ability of the barriers to withstand the mine environment and on the effect of the barriers on belt operation, ventilation, worker travel, and rock dusting. Fifty barriers were installed at three separate beltway locations, and periodic inspections were made. A year after installation, no defects of the barriers or support hardware were detected, nor was any complaint as to the presence of the barriers made by the mine personnel. To date, 2-1/2 years after installation, the barriers have had no detrimental ef-fect on rock dusting, belt operation, or ventilation. Costs of material, fabrication, and installation are reported herein.

Jan 1, 1984

By H. M. Smith

In studying the chemistry of lubricating-oil fractions from so-called ?paraffin-base? crudes, one of the first requisites is a method for the separation and removal of waxy material. A method utilizing solvents for this purpose is described in this report, together with preliminary experiments with solvents that led to its development. The solvents actually used are secondary butyl alcohol, acetone, and mixtures of these.. Isopropyl alcohol was also studied. Preliminary Experiments In previous work on "intermediate-base" crude oil, following the work of Wyant and Marsh acetone had been used for laboratory separations of oil and wax. Then acetone was tried for the separation of the waxes and oils of "paraffin-base" crude, the volume of acetone required (80 parts to 1 part of oil) was found to be too great for large-scale work. For this reason the effectiveness of other solvents was studied; the separation by acetone, however, was used as a standard.

Jan 1, 1927

By K. K. Kershner

The purpose of this investigation was to develop methods on a laboratory scale for recovering tin from metallurgical slime, Tin chlorides were volatilized using mixtures of hydrogen chloride and reducing gases, such as hydrogen, carbon monoxide, hydrogen sulfide, ethane, propane, and butane. Optimum conditions were found to be n mixture of 3:1 of hydrogen and hydrogen chloride at 475° C. Over 95 percent of the tin was volatilized as chlorides. Low temperatures and relatively rapid rates of reaction are distinct advantages of the chloride volatilization process. Research is being continued with various slimes and will be extended to tin ores, where the method offers interesting economic possibilities in comparison with current tin-smelting practice.

Jan 1, 1957

By J. G. Stuart, A. W. Cipkins, R. H. Thompson

Preliminary safe distances for blasting wiring from typical electromagnetic sources are presented. The distances are for underground coal mines and electromagnetic sources in the frequency range below 10 MHz. The distances are based on measurements performed at 3 locations in each of 3 coal mines. The measurement apparatus, measurement procedure, measurement results and the rationale used in the calculation of the safe distances are all described. The safe distances presented are dependent on the measurement results and their interpretation. More measurements are clearly necessary to establish the validity of the suggested distances.

Jan 1, 1985

By R. S. Dean

The principle of explosive crushing depends upon the fact that an expandable substance contained within the pores of a solid body will disrupt such a body upon expansion. Such expansion may be obtained by the detonation of an explosive or by the sudden release of pressure of a superheated liquid. That this principle of disruption may be applied to minerals rests on the fact that cracks, cleavage planes, and pores exist in all minerals to an extent hardly conceived possible heretofore. Crushing by this method takes advantage of forces applied from within the mineral rather than from forces applied from without. The application of a force from within would appear to be more effective.

Jan 1, 1932

By D. Harrington

"In order to stimulate general interest in mine safety among their employees the mining companies of Butte, Mont., instituted in 1918 a Miners' Field Day, and this field day has since been held annually about the end of July, the last one being on July 25, 1921. The mining companies of the Butte district finance this meet in proportion to the number of men employed at the time of the meet, the contributing companies with number of working force, end proportional contributions for the opening field day in 1918 being given below:COMPANY NUMBER EMPLOYED AMOUNT CONTRIBUTEDAnaconda Copper Mining Co.,12,500,$ 1,078.53Butte & Superior Mining Co.,1,800,155.32North Butte Mining Co.,,1,294,111.67East Butte Copper Co.,,850,73.36W. A. Clark Interests,,600,51.78Davis-Daly Mining Co.,,340,29.35,,,,17,384,$ 1,500.00*Note: In many mining districts it is now the custom to hold an annual Miners' Field Day. The field day, as a rule, is financed principally by the mine operators, and was instituted primarily to promote interest among miners in the ""Safety First"" movement. Usually demonstrations or contests in first aid and mine rescue are the leading feature of the day's events, which include games, races, dancing, and all the other amusements usual to a gala holiday. Thus the field (ley serves the double purpose of stimulating interest in mine safety and promoting cordial relations and community fellowship. This paper is an interesting account of the way in which the Miners' Field Day in the Butte district is organized, with data on costs, plan of organization, method of conducting, and the practical benefits derived from it. - Ed"

Oct 1, 1921