Search Documents

By T. G. Carnahan

The Bureau of Mines investigated a flotation-nitric acid leach procedure as part of the goal to maximize minerals and metals recovered from primary and secondary domestic resources. Studies were conducted on an ore that contained carbon-bearing and sulfide mineralization that rendered a portion of the ore refractory (resistant) to conventional leaching technology. The procedure investigated for treating the ore consisted of the following: (1) separation by flotation of the carbonaceous and sulfidic components from the ore, (2) leaching the flotation concentrate with nitric acid at 100° to 110° C, (3) leaching the flotation tailings with sulfuric acid, and (4) processing the combined leached slurries in a conventional manner to recover yellow cake. In step 2, HN03 is converted to gaseous products from which it is regenerated by reacting these products with air and water for further leaching. An overall uranium extraction of 96 pct was achieved by this procedure.

Jan 1, 1979

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTILATION NETWORK ANALYSIS

Jan 1, 1977

By John Ward Smith

Methods for estimating the amounts of nahcolite, dawsonite, and the sum of these two sodium carbonate minerals from oil-yield assay data are developed and evaluated for Green River Formation oil shales from the saline section of Colorado's Piceance Creek Basin. Derived statistically, these estimation methods depend on the fact that these minerals yield water and gas measured during oil-yield assay. The estimation procedures yield values for nahcolite and nahcolite-plus-dawsonite of sufficient accuracy for stratigraphic plotting and correlation, whereas estimates for dawsonite are more generalized. However, resource estimates and reserve computations for both nahcolite and dawsonite accurate within 10 percent of the real value are readily available by summing the mineral amounts calculated by the procedures presented. These estimation procedures are applicable to oil-yield assay data on core samples from more than 30 coreholes which have penetrated the saline section of the Green River Formation in Colorado.

Jan 1, 1972

By Richard F. Hewlett

This report describes a comparison of methods for computing grade and tonnage of ore, leach, and waste material for a mined-out portion of the Silver Bell Oxide porphyry copper deposit, and these computed values are compared with the actual tonnage of these classes of material produced during mining operations. Comparisons with production records have been made by using both exploration drill-hole assays and development blast-hole assays. The polygonal method is the most accurate for this deposit, because it more closely represents the lateral mineral distribution in the deposit. This is demonstrated by plots of the total-copper assay distributions of the development blast-hole assays for a specific bench. The investigation also shows that the smaller vertical assay interval (based on a 5-foot vertical churn-drill-hole sample) yields a more accurate estimate of both grade and tonnage than the 40-foot composite assay interval (based on the average of eight 5-foot assay values). This can be attributed to the fact that selective mining within a bench can separate out much of the waste and leach material that is included as ore in the 40-foot composite assay computations.

Jan 1, 1970

By D. E. Anders

Saturated hydrocarbons from 60 selected samples of a 2,300-foot Green River Formation oil-shale core (Piceance Creek Basin, Colo.) were analyzed by gas-liquid chromatography techniques. Emphasis was placed upon the distribution of normal alkanes and 15 key-branched and cyclic alkanes. The latter compounds consisted of the C15, C16, C18, C19, and C20 chain isoprenoids, the 5-a and 5-ß C27, C28, and C29 steranes, three C30 pentacyclic triterpanes, and perhydro-ß-carotene. The results showed definite evidence of maturation of both the n-alkanes and the branched and cyclic alkanes; however, most if not all of the changes were limited to the indigenous soluble extract and were not the result of additional soluble extract generation from the insoluble kerogen. Source material and environmental variations were important factors in some of the observed differences in the branched plus cyclic alkane compositions.

Jan 1, 1973

This report presents test results, data evaluations, and typical system performance expectations based on wireless electromagnetic propagation measurements performed in the MAGMA Copper Company's San Manuel mine near Tuscon, Arizona during March 30 through April 2 1981. In particular, and at the Bureau's request, this work was coordinated with testing of MF prototype vehicular radios being developed by A.R.F. Products, Inc. with USBM support under Contract H0308004 as part of a system to be marketed by Mine Safety Appliance Co. This testing also employed a prototype vehicular antenna developed by Terry S. Cory, P.E. with USBM upport under previous Contract P0382223. The work was performed under USBM contract J0308012, Propagation of EM Signals in Underground Metal/Non-metal Mines. The authors wish to thank Mr. Hank Seany, Manager of Mines and Mr. Bob Zerga, Mine Superintendent who so kindly arranged for the visit. Particular thanks are given to Mr. Al Metcalf who arranged the logistical details of our underground work, and whoa forward thinking program toward improving general mine communications at MAGMA provided the test-bed context for evaluation of the prototype equipment. The authors also wish to thank Benny Jiminez, Paul Ayala, Lorenzo De La Cruz, and Kent Billhartz for their day-by-day support of the testing. Mr. Jiminez's effort was instrumental in performing the testing, and he also provided a detailed understanding of the existing multi-level, multi-frequency trolleyphone system at MAGMA. the authors are also indebted to Dr. Larry Stolarczyk of A.R.F. for numerous detailed consultations on MF technology, and who was present and participated in the majority of the testing. 1.1 GENERAL BACKGROUND ON COPPER MINING AT MAGMA the San Manuel mine is the largest copper mine in the U.S., efficiently extracting copper and molybdenum sulfide from the low-grade San Manuel ore body.This ellipsoidal ore-shell body, with major workings located 2000-3000 feet mbelow the surface, has ore shell thickness varying between 100 and 1000 feet over a longitudinal extent of some 8000 feet, and with major & minor crossectional axes of about 5000 and 2500 feet respectively. The San Manuel mine operation employs in excess of 1000 men/shift with gross ore production between 60,000 and 70,000 tons/day. The mining operation employs the block caving technique; actively being implemented on three levels (2075,2375,2675 feet for haulage, and 2015,2315,2615 product/grizzly levels). The ore haulage is largely via D.C. trolley trains to four (3A,3B,3C,3D) product shafts for skipping to the surface. An additional three shafts at two locations are used to convey men, materials, and developmental rock extractions into and out of the mine. On each haulage level, the trains carry ore an average of two miles one-way from the ore raises to the dump points. 1.2 TOPOLOGICAL BRIEF OF THE HAULAGE LEVELS The 2375 level, on which all the testing was conducted, is illustrated in

Jan 1, 1981

By E. L. Burwell

Application of the in situ recovery process to oil shale was tested during two field experiments near Rock Springs, Wyo. The results of these tests demonstrate that a self-sustaining combustion zone can be created in an oil shale body, that this zone can be moved through the oil shale, and that the process will produce shale oil. Evaluation of the combustion process by monitoring produced fluids for physical and chemical properties and volumes is described. The material and energy balance obtained is compared with a second evaluation based on extensive coring of the test area after the test was terminated. Several side results of the research are noted such as ground surface heating by underground burning and production of low-to medium-Btu gas during retorting.

Jan 1, 1973

By Manuel Gomez

A general prediction model for the Hardgrove grindability index was constructed from 735 coal samples using the proximate analysis, heating value, and sulfur content. The coals used to develop the general model ranged in volatile matter from 12.8 to 49.2 percent, dry basis, and had grindability indexes ranging from 35 to 121. A restricted model applicable to bituminous coals having grindabilities in the 40 to 110 range was developed from the proximate analysis and the petrographic composition of the coal. The prediction of coal grindability within a single seam was also investigated. The results reported support the belief that mechanical properties of the coal are related to both chemical and petrographic factors of the coal. The mechanical properties of coal may be forecast in advance of mining because the variables used as input to the prediction models can be measured from drill core samples collected during exploration.

Jan 1, 1970

Roof screening for ground control originated with metal miners in the western United States. At first chain-link fence was used, but because it was so difficult to handle, the miners started installing a more rigid welded wire screen used in the concrete industry. Eventually coal mines in the west began to use screen, and now more and more coal operations, especially longwall mines, are installing roof screen on a regular basis. Screen use has recently increased in the Illinois basin and is now making its way to underground coal mines in the eastern U.S.

By Benton L. Tibbetts

Comprehensive geophysical measurements were made in the Tertiary Channel gravel deposits of Badger Hill, Calif., with the refraction seismograph, gravimeter, and well logging equipment, to develop a three-dimensional physical model of the gold-bearing gravels. Tests were also made of the applicability of magnetometer and electrical resistivity techniques. Results of 14 seismic profiles revealed four distinct layers with velocities of 1,600 ft/sec for loose gravel, 5,900 ft/sec for compact gravel, 8,600 ft/sec for cemented, blue gravel, and 15,500 ft/sec for bedrock. The depth to bedrock along the middle of the channel varied from a minimum of 100 feet in the hydraulically mined pit area to a maximum of about 300 feet in the upper bench area immediately south of the pit. These geophysical methods revealed that 40 percent of the drill holes necessary to delineate the deposit could be eliminated, at a cost saving of at least 30 percent.

Jan 1, 1971

Until man was able to produce light, his working day was pretty much limited to daylight hours. Underground miners have a special problem because in a mine it is just as dark during daytime as it is at night. The first devices used for mine lighting were torches and open flame 011 lamps. Torches made from twisted grass and dipped in tallow or pine pitch would burn for a while, but they made a lot of smoke and probably went out when they were needed most. During the 15001s, miners lamps consisted of a small metal dish with a hook attached to hang it up. The saucer-shaped dish was filled with animal or fish oil and a wick made of twisted fibers was laid In the 011 and hung over one edge where it would burn. This lamp would burn longer than a torch, but the amount of light cast by the pale, flickering flame was probably only a little better than no light at all.

Jan 1, 1976

By R. K. Koch

The vapor pressures of liquid columbium and liquid hafnium were deter-mined by the Langmuir free evaporation method as a part of the Bureau of Mines program on the study of transition metals. An electron-beam furnace with a water-cooled copper crucible was used for melting. Temperature was measured with a two-color ratio pyrometer. Least-squares analyses of the vapor pres-sure data gave the following equations: [Logp (atm) = 5 .429 -31,310 T] for liquid columbium in the range 2,740° - 3,140° K, and [Log p (atm) = 5,690 28 T] for liquid zirconium in the range 2,500° -2,810° K. Third-law evaluations of each data set gave mean heats of sublimation (298.15° K) of 175.1±3.2 kcal/mole and 148.3±1.2 kcal/mole for columbium and hafnium, respectively. Second-law standard heats of sublimation determined from sigma plots and from sigma-prime plots agreed fairly well with the third-law values. The sigma-prime plots gave standard entropies of sublimation of 30.96±0.84 eu and 33.S6±0.44 eu for columbium and hafnium, respectively.

Jan 1, 1968

By Bill M. Stewart, Philip W. Patton, Curtis C. Clark

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines we revisited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.

To precondition a stope in advance of mining and thus reduce or prevent rock bursts. Approach Drill deep holes from a mine opening in a radial pattern in the vein and load and blast to fracture, the rock prior to production mining How It Works Preconditioning of a sphalerite galena vein in a hard gangue of quartz and quartzite creates a zone of softer rock that fails by displacement rather than violently as an elastic-battle mass. However, the entire area must he analyzed carefully so that the stress transfer does not cause problems in other workings of the mine A typical drill hole pattern and explosive loading is shown in the sketch. Hole diameter is about 4 inches and a down-the-hole, type drill is used. Drilling speed in hard quartzite is about 12 inches per minute High pressure compressed air (250 psi) is used to run the drill. An overhand cut-and-fill stoping area on the 7700 level of Hecla Mining Company's Star Mine in Burke, Idaho was preconditioned above and below the

Jan 1, 1981

By Dennis R. Dolinar, Lewis A. Martin

Cable bolt technology used by the U.S. coal industry was developed to a large extent in the 1990s. Today, these cable systems include both cable bolts and cable trusses to provide supplemental and secondary support in gate roads. This cable technology is significantly different than the cable systems in use in either U.S. hard-rock mines or Australian coal mines. Development of this technology was initiated and spurred by research efforts of the U.S. Bureau of Mines, and has continued under the health and safety programs of the National Institute for Occupational Safety and Health (NIOSH). It was also followed up by work of roof support manufacturers to create an essentially new support system. In this paper, the important support characteristics of both cable bolts and cable trusses are discussed. The design of cable systems and the basis for that design for tailgate and headgate situations are reviewed and explained. Case histories are presented on the application of these support systems based on experience gained at a number of in situ test sites.

Jan 10, 2000

By Larry A. Haas

The U.S. Bureau of Mines investigated the use of organic binders as substitutes for bentonite in agglomerating iron ore concentrate. Over 30 organic binders were evaluated at several dosage levels in laboratory tests. The binder groups producing the greatest green pellet strengths were natural gums (guars carboxyl methyl celluloses) and gelled starches. The nongelled and alkalized starches, starch acrylic copolymers) wood-related products, and dairy products were less effective but better than bentonite. The highest wet pellet drop numbers were obtained with binders that had a medium plate water absorption value (>500 and <10)000) in distilled water and a high slurry viscosity (>75 cP) at 6 pet solids. The highest dry compressive strengths were obtained with binders that gave the highest adhesive tensile strength (>4 kg/ cm2) on iron oxide lap-joint substrates. Pellets with 0.1 pct organic binder had lower compressive strengths and reduction disintegration indices than those with 1 pct bentonite, but higher reduction rates. Pellets with carboxyl methyl cellulose and gelled starch had higher softening temperatures than those with bentonite. Overall, the most promising binder is gelled starch. Its price makes it more cost effective than carboxyl methyl cellulose, and its pellets have metallurgical properties superior to those of bentonite pellets.

Jan 1, 1989

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 1992

By H. E. Peterson

This report revises an earlier publication by the Bureau of Mines on tungsten analytical procedures and expands the coverage by including appropriate procedures for the critical impurity elements that commonly occur in tungsten ores and concentrates (13).3 The basic methods described are not original, but many of the modifications to improve reliability and sensitivity were developed by the Bureau. Gravimetric and colorimetric methods currently used for the determination of tungsten in ores, mill tailings, and concentrates are described. Colorimetric procedures are preferred for low concentrations of tungsten, whereas either procedure is satisfactory for moderate concentrations. Conversely, a gravimetric method is preferred for the determination of tungsten in concentrates.

Jan 1, 1963

By T. E. Ackman

The Bureau of Mines conducted a study of current trends in methods employed by the coal industry to dispose of acid mine drainage (AMD) treatment sludge. Thirty-three AMD treatment plants, operated by 11 Pennsylvania coal companies, were randomly surveyed. These plants provided data for calculating sludge volumes, as well as information on sludge settling, transportation, and disposal. Onsite visits allowed observation of problems associated with the various methods of sludge disposal: (1) disposal into a deep mine, (2) permanent retention in ponds, (3) disposal at an active coal refuse area, and (4) onsite burial. Method 1 is the most frequently used and the most environmentally sound. It is apparent, based on this representative sampling of AMD treatment plants, that the magnitude of sludge production is such that an aggressive and directed effort in reduction of sludge volume is seriously needed. The areas of major concern are (1) the amount of surface land required for sludge storage and disposal, (2) reclamation of these disturbed surface areas, and (3) effective and efficient means of removing, transporting, and disposing of AMD sludge. In this report, an engineering approach to the practical problems associated with the existing disposal methods is presented, together with recommendations for future research.

Jan 1, 1982

By W. E. Lamont

Flotation studies of phosphate-bearing waste pond materials, low-grade washer products, and raw ores, all from the Tennessee brown phosphate district, showed that these types of materials could be treated without des liming to recover high-grade phosphate concentrates. The investigation showed that fine grinding before flotation was a requisite for increased recovery of the phosphate values and that the optimum pH conditions were in the range of 10.0 to 10.5 when using anionic collectors. Multiple-cleaning of the rougher phosphate concentrate was required to produce high-grade concentrates. Phosphate recoveries ranged from 60 to 82 percent and were inversely related to the grade of concentrate produced.

Jan 1, 1972