Search Documents

By F. P. Haver

Because of increasing concern with air pollution, the Bureau of Mines has developed a hydrometallurgical procedure to obtain elemental sulfur from chalcopyrite (CuFeS2) by means of the following reaction: CuFeS2 + 3FeCl3 ? CuCl + 4FeCl2 + 2S. Under optimum conditions, 99.6 percent of the copper and 71.6 percent of the iron were extracted in 2 hours from a typical mill concentrate containing 75 percent CuFeS2 and 15 percent pyrite (FeS2). At the same time, 68.2 percent of the sulfur in the concentrate was oxidized to the elemental form. The leach was highly selective; gangue minerals, including pyrite, were not attacked, thus accounting for the relatively low recoveries of iron and sulfur. To obtain these results, the concentrate was ground to 98.9 percent minus 325 mesh, and 300 grams was treated with 1 liter of boiling ferric chloride (FeCl3) solution. The FeC13/CuFeS2 ratio was 2.7. Cement copper containing 99.9 percent copper was recovered from the leach solution by cementation on sponge iron. Excess iron, dissolved during leaching and cementation, was removed from the stripped solution by crystallization. Ferrous chloride (FeCl2?4H2O), obtained as a byproduct, was converted to high-purity ferric oxide (Fe203) and HCI by an oxidizing roast. The hydrochloric acid was then electrolyzed to obtain chlorine, which was used to regenerate the leach solution. The leach residue, which contained ~50 weight-percent elemental sulfur, was treated with an organic solvent to recover the sulfur and cyanided to reclaim gold and silver.

Jan 1, 1971

By Spencee L. Willett

In 1984, at the request of the Bureau of Land Management, the U.S. Bureau of Mines conducted mineral surveys of the 20,508-acre Blue Lakes (NV-020-600) and 5,142-acre Alder Creek (NV-020-600D) Wilderness Study Areas (WSAs) in northwestern Humboldt County, Nevada. The WSAs are part of an upthrown, north-south trending fault block associated with the Basin and Range province. Both areas are predominantly underlain by the Cretaceous Duffer Peak pluton which intrudes Triassic metasediments and Jurassic plutonic rocks to the east and Permian Happy Creek volcanics to the south. In the Alder Creek WSA and in the southwest portion of the Blue Lakes WSA, Duffer Peak granodiorite and Happy Creek volcanics are overlain by Tertiary basalt. No active mines exist within the Blue Lakes WSA; but, several prospects, claims, and mineralized outcrops are in the south and northeast portions. No mineral resources were identified but samples from discontinuous, vein-type deposits contained anomalous amounts of gold, silver, copper, lead, zinc, molybdenum, antimony, and uranium. Very fine, residual gold was detected in nine alluvial samples collected from a small deposit in the southwest corner of the WSA; average gold value was $3.58 per cubic yard (at $350/ounce). Two mines, several prospects, and mineralized outcrops adjacent to the Blue Lakes WSA contain mineralized, irregular structures which do not appear to extend into the Blue Lakes study area.

Jan 1, 1986

The National Personal Protective Technology Laboratory (NPPTL) of the National Institute for Occupational Safety and Health (NIOSH) has undertaken a collaborative study with the Mine Safety and Health Administration (MSHA) to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), withstand the underground coal mining environment with regard to both physical damage and aging. Apparatus tested included the CSE SR-100, the Draeger OXY-K Plus, the MSA Life-Saver 60, and the Ocenco EBA 6.5 and M-20. This report presents findings regarding laboratory-tested SCSRs in the tenth phase of testing, from July 2004 to March 2006. The SCSRs were tested on a breathing and metabolic simulator and on a human subject walking on a treadmill. The tests performed in this study are not the tests used for certification (Title 42 of the Code of Federal Regulations, Part 84). The tests performed in this study continue until the apparatus are empty to enable comparison of new versus deployed apparatus. The method for obtaining deployed SCSRs for this evaluation was not a random selection from the deployed population of SCSRs. We sought older apparatus with visible environmental impact rather than newer apparatus, and we attempted to sample a wide range of deployment modes. Although the results of these tests are useful for observing performance of the tested SCSRs, they are not representative of all deployed SCSRs. This report is the last of 10 report phases begun in 1982. Previous reports describe phases 1 through 9 [Kyriazi et al. 1986; Kyriazi and Shubilla 1992, 1994, 1996, 2000, 2002, 2004, 2006] A new evaluation protocol, with revised sampling strategies, test methods, and reporting procedures, is currently being designed to enhance the applicability of the results. The results of these studies suggest that the large majority of SCSRs that pass their inspection criteria can be relied upon to provide a safe level of life support for mine escape purposes. However, the storage and handling in the mining environment seems to have caused performance degradation in some of the apparatus. In this phase, phase 10, we found some CSE SR-100s (93 tested) that exhibited high CO2 levels, stuck-together breathing hoses, starter-O2 failure, breathing hose punctures and tears, high breathing pressures, and loose particulates in the breathing hose. The loose particulates caused coughing in human-subject tests. One MSA Life-Saver 60 (20 tested) in this phase had a stuck-open relief valve. One Ocenco EBA 6.5 (50 tested) had an unattached O2 supply hose. An unexplained phenomenon occurred with two Ocenco M-20s (20 tested): low O2 flow rates preventing their successful use. Almost all of the failures noted involved units that failed their inspection criteria.

Jan 6, 2008

By J. E. Tiffany

Some of the gases produced by permissible explosives on detonation are poisonous, and the probable hazard involved by the inhalation of carbon monoxide in the past has been evaluated from results of tests in the Bichel Gage. Tests have now been made in the Experimental Coal Mine of the Bureau of Mines at Bruceton, Pa., to determine the composition of the gases obtained under actual mining conditions for the purpose of comparing these, results with those found by the Bichel gage tests. Two permissible explosives were procured for these tests, one that produces a relatively low quantity of poisonous gases in the Bichel gage (24.8 liters per 1-1/2 pounds of explosive) and another that produces a relatively high quantity of poisonous gases (94.6 liters per 1-1/2 pounds). The first of these is designated by the Bureau of Mines as a class A4/ explosive and the other is designated a class B explosive. In comparison with Bichel-gage tests, the shooting of permissible explosives in a coal shot hole resulted in a large reduction in the quantity of carbon monoxide, the principal poisonous gas, which; in the mine tests, was only 22 percent of that found in Bichel-gage tests: The quantity of carbon monoxide from the class B explosive in Bichel-gage tests was 3.8 times larger than that from the class A explosive; in the coalmine tests the ratio was 4:1. The concentrations of carbon monoxide in the mine tests, as determined by analysis of the atmosphere in an enclosed space resulting from shooting 1-1/2-pound and 3-pound charges of the class A explosive, were 0.03 and 0.06 percent, respectively, and the concentrations from 1-1/2-pound and 3-pound charges of the class B explosive were 0.10 and 0.24 percent.

Jan 1, 1950

By E. H. Denny

Colorado coal-mine fatalities, which have gradually decreased since 1914, have shown a marked decline since 1924. Data on coal-mine fatalities in Colorado published by the U. S. Bureau of Mines5 indicate that the deaths per thousand 300-day workers have decreased from 9.13 in 114 to 6.14 in 1926, and that the deaths per million tons produced have decreased from 9.18 in 1914 to 4.98 in 1926. Table 1 gives fatality rates in Colorado and in the United States from 1914 to 1926 inclusive. [ ]

Jan 1, 1929

By J. R. Bartels

Operation of underground coal mine mobile equipment is usually done in a restricted workspace with reduced visibility. This work environment puts machine operators in awkward postures for tasks that require awareness of their surroundings and fast reactions to avoid hazardous situations. Using experienced equipment operators as a source, researchers conducted an investigation that developed a method to gather data on the needs and practices of machine operators while controlling the machine and the reasons for needing particular operational cues. The method used was an interview technique including a survey questionnaire and visual aids. The data gathered defined operator cues and work positions for the cutting and tramming phases of remote controlled continuous mining machines used in underground coal mines. Analysis techniques to determine which cues an operator sees from a variety of positions utilizing a computer simulation is shown to be potentially useful to the mining industry for design of work practices and workplace layout and could impact equipment design and selection for improved worker safety. Conclusions indicate that the survey was a good research tool to collect data and helped investigators understand important visual cues. Using this information, researchers were able to analyze the visual cues an operator can see from a given work position and posture.

Jan 1, 2009

By James A. Wasson

The Mitchell and Berea sands were cored and logged in Fred Link well K-l, Lower Newport field, Washington County, Ohio. Core and reservoir fluid analyses and available field data were studied to determine if these sands could be successfully waterflooded. The results of the study indicate that there is insufficient oil in place to form an oilbank in either the western Mitchell pool or the Berea sand, and that no commercial recovery of oil by waterflooding can be obtained in these reservoirs.

Jan 1, 1967

By John B. Knaebel

Hammer machines are now widely used for underground sampling and exploration. Their application to such work can be divided into two classes - sampling and testing with ordinary drilling equipment to shallow depths of 22 feet or less, and "long hole" drilling with heavy machines and special equipment to depths of as much as 250 feet or more. In the first category hammer drills are employed for either of two distinct purposes: first, as a means of checking the results of grab or cut samples or, in certain types of ore deposits, as a substitute for these methods; and second, as a method of sampling the ground 5 to 20 feet beyond existing faces and thus aiding in the control of stoping operations or in the direction of development headings, as the case may be. The deep-hole drill, in the second category, has proved to be a valuable adjunct to the old established methods of exploring, end developing ore, provided it is employed under natural conditions to which it is suited, handled by men thoroughly familiar with the technique of its operations, and used with its possibilities and limitations clearly understood.

Jan 1, 1932

By S. P. Kinney

Economy in blast-furnace practice depends largely upon efficient gas-solid contact in the shaft of the furnace. If efficient work is not done in the shaft the hearth and bosh will not function properly. A condition may be readily imagined where the particles of ore in the shaft are so large that the time entailed in the descent of these materials into the bosh is not sufficient to permit proper reduction and preparation prior to the time the ore enters the bosh of the furnace. Another condition may be pictured where the density of the stock column and the flow of stock is such that the ore will take one course and the gas another. Both of these examples will result in insufficient contact between the gas and the ore. Unreduced ore will reach the hearth, and gas which has not been efficiently oxidized will reach the stock line. The result is the use of an excess of carbon in the smelting process. An example of the result of inefficient gas-solid contact in the shaft of a blast furnace is shown by the curves in Figure 1.

Jan 1, 1930

By J. G. Kirby

According to the Bureau of Mines annual survey, there were 319 petroleum refineries in the United States as of January 1, 1957 capable of processing 9,123,674 [ ]-barrels of crude oil daily. This was the first time in eleven years that the total number of refineries increased. The crude throughput capacity of the refineries increased 491,284 barrels daily (6 percent) above the January 1, 1956 capacity. The East Coast and Texas Gulf Coast refining districts accounted for 60 percent of the additional capacity installed. Three new refineries were put into operation on the East Coast during the year with a total daily crude throughput capacity of 154,434 barrels while the other refineries in the district report a net loss in capacity, installing equipment capable of processing 140,000 barrels, but dismantling equipment with a capacity of 150,100 barrels. In the Texas Gulf Coast district, one new refinery with a daily crude oil capacity of 5,000 barrels was placed in operation in 1956 and 143,700 barrels of crude capacity was added to existing refineries. The capacity of the average refinery to process crude oil increased from 27,145 barrels daily to 28,601 barrels in 1956.

Jan 1, 1957

By G. F. Friel

A series of experiments in the U.S. Bureau of Mines Safety Research Coal Mine at the Pittsburgh Research Center evaluated the effects of crosscuts on the travel time of carbon monoxide (CO) along an entry to improve the accuracy of a mine-fire locator program. Three entries, ten single crosscuts, and three double crosscuts were instrumented with CO sensors. One-percent CO in nitrogen was released and monitored as it traveled the entries. In addition to dispersion of CO at the front of the CO wave, CO was entrained from the entry into the crosscuts. It was determined for an entry and single-crosscut configuration that the measured travel time for a concentration change of 5 ppm was 27% greater than the predicted time based upon entry volume only, but 13% less than the predicted time based upon entry and crosscut volumes. For an entry and double-crosscut configuration, the measured travel time for the same concentration change was 25% greater than the predicted time based upon entry volume only, but 10% less than the predicted time based upon entry and crosscut volumes. An effective dispersion coefficient for CO dispersion along one of the entries was estimated to be 1.5 m2/ s.

Jan 1, 2010

By J. Kruttschnitt

This paper, describing milling practice at Mount Ira Minis, is one of a series covering milling methods and cost that is being published by the Bureau of Mines, United States Department of the Interior. The Mount Isa concentrator began operations in day 1931 by treating a mixture of oxidized and sulfide ores. Since March 1935 only sulfide ores have been milled; this change involved major alterations to the flow sheet. The maximum capacity on mixed oxide and sulfide ores was 2,650 tons per day; the present capacity is approximately 1,880 tons of sulfide ore per day. The installation of additional crushing, grinding, and flotation equipment when completed early in 1939 will increase the maximum capacity of the concentrator to 2,240 tons of sulfide ore daily.

Jan 1, 1939

By L. B. Pankratz

High-temperature heat contents were measured for two praseodymium oxides and three terbium oxides. There were: Pr2O3 (298° to 1,600° K), PrO1.833 (298° to 1,050° K), Tb2O3 (298° to 1,600° K), TbO1.719 (298° to 880° K), and TbO1.812 (298° to 850° K). With the exception of PrOl.833, all results were regular. PrO1.833 had a small thermal anomaly at 760° K with an extra absorption of 380 cal/mole. The measured heat content values, tabulated smooth heat contents, and entropy increments are reported. Heat content equations were derived.

Jan 1, 1966

By M. Paczkowski

The use of inert gas systems to extinguish mine fires has been the subject of research for some time in the United States. In some European countries, it is an established practice. Tests were conducted with the CMI Inert Gas System (CMI), which is being used by the Polish mining industry. This system utilizes a modified jet aircraft engine and afterburner as a compact source of combustion products with a very low (less than one percent) oxygen content. Water injected into the combustion products stream provides evaporative cooling and forms a mist with a high cooling capacity. The CMI system was used under controlled conditions to extinguish coal pile fires at the U. S. Bureau of Mines Experimental Mine in Bruceton, Pennsylvania. The test results show that the CMI system can be used conveniently to extinguish fires quickly and to maintain an inert atmosphere in the fire zone to prevent re-ignition.

Jan 1, 1982

By C. M. Frost

The hydrodesulfurization characteristics of a residual fuel prepared from Wilmington, Calif., crude oil were determined at temperatures from 600° to 900° F, pressures of 200 to 800 pSig, and space velocities from 0.2 to 2.0 Vo/Vc/hr, using cobalt molybdate type catalysts. A prediction equation, developed from the experimental data, satisfactorily predicts the fraction of total sulfur that can be removed under any combination of operating conditions within the ranges investigated. Yields and properties of the low sulfur product are correlated with the fraction of total sulfur removed. Kinetic calculations show that the apparent reaction order and activation energy change with space velocity and temperature.

Jan 1, 1970

By William H. King

The Fannie Ryan deposit is situated about 9 miles northwest of Boulder City, Clark County, Nev. at an altitude of about 2,000 feet on the north side of the River Mountains. The deposit is covered by several unpatented claims owned by Fannie B. Gulick of Las Vegas, Nev. The Boulder City deposit is within the Hoover Dan National Recreational Area. It is situated about 3 miles southeast of Boulder City in sec. 23,T. 23 S., R. 64 E., Clark County, Nev. The Deposit was covered by several unpatented mining claims owned by S. R. Whitehead of Las Vegas. The deposits occur in sedimentary beds of the Muddy Creek formation that overlie older volcanic extrusive. The manganese minerals occur as soft oxides of the wad type. The exploration was conducted by the Bureau of Nines in cooperation with the Federal Geological Survey and comprised a study of the geology, mapping of the areas, and development by shaft sinking; diamond drilling, and sampling. On the Fannie Ryan Gulick property the work consisted of cleaning and sampling seven old trenches on the outcrop and diamond drilling seven holes totaling 1,482 foot. At the Boulder City deposit 188 feet of drilling was done in two holes. A 4- by 6-foot shaft was sunk to a depth of 44.5 feet, and the north and south sides of the shaft were sampled.

Jan 1, 1950

By Michael S. Miller

In 1985, at the request of the Bureau of Land Management, the Bureau of Mines studied a 50,57U-acre portion of the 90,345-acre Twin Peaks Wilderness Study Area (CA-020-619A) in order to evaluate its identified resources. The area studied is located about 45 miles northeast of Susanville, CA, in Lassen County, CA, and Washoe County, NV. The area is underlain by Tertiary volcanic, volcaniclastic, and intrusive rocks. Quaternary stream, lake, and landslide deposits overlie the older rock. There are no mines or mining claims in the study area. One mineral resource, pozzolan, was identified. Mining claims, inactive in 1985, have been staked adjacent to or near the northwest corner of, and also southeast of, the study area. Examination and sampling of 17 mineralized sites, delineated mostly by prior geochemical surveys, showed at least 30 million tons of subeconomic pozzolan resources and small or low-grade occurrences of gold, silver, copper, lead, zinc, nickel, molybdenum, zeolites and clay.

Jan 1, 1986

By G. W. Birge

Carbonizing properties of the principal coalbeds of Elk, Clarion, Jefferson, Clearfield, and Centre Counties, Pa,, are described in this Bureau of Mines report, Twenty-six samples, representing the Upper Freeport, Lower Freeport, Upper Kittanning, Middle Kittanning, Lower Kittanning, and Brookville beds, were carbonized by the Bureau of Mines--American Gas Association (BM-AM) method, and yields of products and physical properties of cokes were determined. Expansion or contraction of the majority of the samples was measured in the Bureau of Mines sole-heated oven. Chemical analyses, agglutinating values, and free-swelling indexes are given for all samples. In this area the coals generally are characterized by high sulfur and moderately high ash content, and their suitability for metallurgical use would depend largely upon satisfactory cleaning. The samples from Elk, Clarion, and Jefferson Counties were high-volatile A bituminous In rank, whereas, most samples from Clearfield County and all those from Centre County were of medium-volatile rank. Coals from Clarion County had dry, mineral- matter-free fixed-carbon contents ranging from 56.5 to 60.3 percent and were weakly coking. With the exception of two samples which contained excessive ash, the medium-volatile coals of Clearfield and Centre Counties were strongly coking and, as indicated by sole-oven expansion results, would require blending with lower rank coal to avoid oven damage.

Jan 1, 1963

By R. H. Nicholas

Shuttle cars have undeniably proved their worth as a means of transporting coal underground; however, several factors have arisen in connection with their possible improvement. This report .discusses the effect of shuttle cars that employ rough-tread and smooth-tread tires on mine roadbed, the amount of dust thrown into suspension by the use of such tire treads, and the service rendered by each type of tire. Involved, also, in this study are observations on the use of different amounts of calcium chloride on the haulageways.

Jan 1, 1949

By E. A. Barrett, K. M. Kowalski

The U.S. Bureau of Mines (USBM) conducted experiments to determine if training using a latent- image, three-dimensional (3-D) slide simulation exercise improved miners' ability to recognize roof and rib hazards. The effectiveness of this innovative type of classroom training was investigated by measuring workers' performance on a hazard recognition task. The study was unique in that hazard recognition skills were assessed in the workplace using actual coal mine roof and rib hazards. Results showed that training with a latent-image, 3- D slide simulation exercise significantly improved each subject's performance on the in-mine hazard recognition task. Further, the USBM researchers concluded that transfer of learning from the classroom to the workplace occurred.

Jan 1, 1995