Search Documents

By Thomas Fraser

About 24 per cent of our total production of bituminous coal is used in industrial power plants. As regards fuel conservation, therefore, the recovery of unburned fuel from furnace refuse presents interesting possibilities. Considerable attention has been given to this problem in the past, but because of the comparatively low initial cost of power plant fuel in the pre-war period little progress, has been made in this direction in the United States. Because of the higher price of coal in Europe more attention has there been given to the problem. In Germany a process has been developed for separating unburned coal in refuse by using an electromagnetic separator In the United States the use of mechanical stokers enabled low-priced screenings of high ash content to be used, so that even with relatively high percentages of combustible material remaining in the refuse, the loss in money is not excessive. If the price of screenings returns to the pre-war level around $1.00 per ton the process proposed here will probably not be especially interesting, except where the freight charges are very high. However, if the price of delivered coal continues high, such a process should result in considerable saving. The cost of continuous operation of such a refuse treating plant should not exceed 75 cents per ton of fuel recovered.

Jan 1, 1921

In 2007, a total of 7,199 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 ? Sand and gravel mines were the largest mining sector, comprising 48.4% of all mining operations. ? Sand and gravel mines were found throughout all 50 states and Puerto Rico.

Aug 1, 2009

By R. W. Huber

Three arc-melted ingots, two of a titanium-7 percent manganese alloy and the third of unalloyed titanium, were forged and rolled into 3/4-inch plate; comparative data were obtained on these processes. The finished plate, part of which was used by the Naval Bureau of Ordnance, was tested for mechanical and other properties. These properties were correlated with sponge purity, forging technique, rolling temperature, and cooling rate from the rolling temperature. For the alloy material, transformation data were obtained, and their age-hardening characteristics were studied. The temperature-impact relationship was established for rolled sections from all three ingots. INTRODUCTION Arc-melted ingots of unalloyed titanium and a titanium-manganese alloy were fabricated into plate under closely controlled conditions by personnel of the Metals and Alloys Section, Physical Metallurgy Branch, Bureau of Mines, College Park, Md. This program was cosponsored by the Naval Bureau of Ordnance. Bureau of Mines interest lay in correlating the processing procedures with the mechanical properties of the finished plate.

Jan 1, 1955

By J. H. Rose

This paper describing the milling practice at the Magma Copper Co., Superior, Ariz., is one of a series being prepared by the Bureau of Mines on milling methods and costs in the various mining districts throughout the United States. ACKNOWLEDGMENT The authors wish to acknowledge their indebtedness to William Koerner, general manager of the Magma Copper Co., for permission to prepare this article; to J. S. Garrott, former mill superintendent, for the historical facts; and to Walter Cooksley, general foreman, for his assistance in obtaining the data.

Jan 1, 1930

By C. E. Reistle

The generation of steam for drilling operations has visually been accomplished in the past by the use of portable locomotive-type boilers without the aid of auxiliary equipment or advanced for economizing fuel or water consumption. This has been due primarily to the fact that the steam-generating plant of a drilling well must necessarily be of temporary and portable design, and the amount of steam generated has not been considered sufficient to justify the additional expense necessary to obtain more economical operation. However, with the constantly increasing depth to which oil wells are being drilled and the use of larger and heavier equipment, the steam requirements have reached a point where equipment and methods that were previously considered as applicable only to permanent plant installation can be and are being used to a decided advantage by the more progressive operators. As an example of the present-day requirements and the rapidly increasing steam consumption in rotary drilling, a comparison between the requirements during the intensive drilling period in the Seminole end Oklahoma City fields of Oklahoma is of interest. In the Seminole field. There the approximate depth of rotary drilling was 3,500 feet, the general practice was to use three 85 to 90 or 100 horsepower A. P. I. code boilers operating at a working pressure of 175 to 200 pounds per square inch. The fuel end water consumption was approximately 450 to 500 thousand cubic feet of gas and 700 to 750 barrels of water per day. In the Oklahoma City field, where the average drilling depth is approximately 6,500 feet, the general practice is to use either four 100 or 116 horsepower or three 123 horsepower A.P.I. code boilers, operating at a pressure of 250 pounds per square inch. The fuel and water consumption varies from 550 to 750 thousand cubic feet of gas and from 1,000 to 1,500 barrels of water per day.

Jan 1, 1930

In 2007, a total of 2,030 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Coal mines comprised 13.7% of all mining operations. ? Bituminous mines comprised 92.4% (n=1,875) and anthracite mines 7.6% (n=155) of coal mining operations. ? Approximately 72% of all coal mines were located in three states: Kentucky (28.4%), West Virginia (22.6%), and Pennsylvania (20.5%).

Aug 1, 2009

By George H. Popper

The Bureau of Mines has evaluated the extent of phosphate resources available for recovery by the experimental borehole mining method in the Southeastern Coastal Plain of the United States- Phosphate re- sources at overburden depths greater than 30 m are as a rule currently unsuitable for recovery through conventional mining methods because of economic, environmental, or technical considerations. In the identified deposit areas, borehole mining operations are projected to yield a more favorable rate of return and to be environmentally more desirable than conventional surface mining. Borehole mining resource estimates presented in this study are preliminary and designed to serve as a basis for future resource evaluations, as the current data base is relatively sparse and incomplete. The resulting resources have, therefore, been classified as hypothetical and speculative and are subject to up- dating as additional exploratory data become available. Hypothetical and speculative resources amenable to borehole mining are estimated to total about 385 billion metric tons (rat) of phosphate matrix with a minimum in situ grade of 5 pct P205. With projected borehole mining capabilities and current conventional beneficiation procedures, this resource would make available approximately 64 billion mt of phosphate rock product at an estimated grade of 30 pct P205.

Jan 1, 1985

By M. H. Kline

The Scarlet mine, in Randolph County, N. C., was operated on a small scale at intervals from 1899 to 1915, but no records of the quantity of ore produced are available. J. I. Moore unwatered the mine in March 1948, and Bureau of Mines' engineers examined the underground workings. Several assays checked previous sampling of the mine and indicated a small but comparatively high-grade copper-zinc deposit. The high metal content of the veins and the possibility of developing additional reserves prompted the Bureau of-Mines to drill three holes, totaling 530 feet, at the deposit during March and April 1948. Drilling disclosed that the mineralized vein did not extend over 300 feet along the strike and is probably limited in depth to the contact with the granite mylonite.

Jan 1, 1949

By J. E. Pahlman

As part of its effort to reduce the need for strategic minerals through conservation and to reduce the capital and energy requirements of mineral processing, the Bureau of Mines has investigated a method for preparing ferrochromium alloys containing less than 2 percent carbon. This method will conserve chromium and should reduce the capital and energy requirements for chromite reduction. Reduced products containing less than 2 wt-pct C and as low as 0.01 wt-pct C were obtained by reacting pellets of chromite and carbonaceous reductant mixtures at pressures of 0.1 to 1 torr and temperatures of 1,230° to 1,320° C. The extent of reduction increased with increased temperature and decreased pressure; however, operating conditions were limited due to the onset of significant chromium vaporization at higher temperatures and lower pressures. Foundry coke, anthracite, and carbon black were found to be supe¬rior to graphite as reductants. The reduction of chromite to metallics was found to proceed via the carbide intermediates (Fe,Cr)7C3 and (Fe,Cr)23C6, No evidence of carbide intermediates Fe3C or Cr3C2 was found. Buttons of ferrochrome alloys were made by melting a mixture of reduced products with CaO and Si02 at 1,700° C for 20 minutes in an induction furnace,

Jan 1, 1980

By Edwin C. Reeder

This paper, describing milling methods and costs at the Hillside Fluorspar Mines at Rosiclare, Ill., is one of a series being prepared for and published by the United States Bureau of Mines on non-metallic milling methods. The milling practice described is that of one of the large mines in the Kentucky-Illinois fluorspar field in southern Illinois and western Kentucky, on the Ohio River. Milling methods throughout the district are similar in their general principles, although details vary considerably in different plants.

Jan 1, 1932

By Dayton C. Bolin

This paper is one of a series being prepared by the United States Bureau of Mines describing quarrying methods and costs at stone quarries throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scrope of the cost tabulations shall ensue. ACKNOWLEDGMENT The author wishes to acknowledge the assistance of J. R. Thoenen, mining engineer, United States Bureau of Mines, in the preparation of this paper. Acknowledgment is also made to E. R. Lederer, vice president in charge of the company's operations, through whose kindness the preparation of this paper was made possible. E. T. Eubank, superintendent of the quarry, and J. A. Hodges, quarry foremen, gave much of their time to this work. The cost data were compiled by the company's chief clerk, J. von Carlowitz.

Jan 1, 1931

By K. E. Stanfield

The Bureau of Mines oil-shale program, initiated in April 1944, is concerned with the future utilization of oil shale in the United States as a source of liquid fuel. One phase of this program is the accumulation of information on the location, extent, and richness of oil-shale deposits that may be suitable for processing to oil and related products. A previous publication5/ presented, by means of logs, the oil yields of sections of the largest known oil-shale deposit in this country -the shales of the Green River formation occurring in adjoining portions of the states of Colorado, Utah, and Wyoming. This present supplementary report presents the oil yields of cores from 48 holes drilled during 1952 to 1954 in the Green River formation of Colorado, which is distributed over an area of more than 1,000 square miles. The oil yields of the 48 oil-shale sections, involving the assay of 9,651 samples, representing 22,451 feet of core, are presented by means of logs. In addition, the oil yields of samples comprising the maximum sections of 15 gallon-per-ton shale are tabulated for these cores and for the 28 cores from Colorado which were logged in the previous report.

Jan 1, 1957

By Raymond B. Ladoo

In order to obtain comprehensive and authentic information on fluorspar mining in the western States , the writer, together with and at the request of representatives of some of the largest fluorspar producers of the Illinois - Kentucky district , spent the month of April , 1922 , in examining all we stem fluorspar deposits ( of which record was available ) believed to be of possible commercial importance .

May 1, 1923

By I. L. Nichols, K. C. Dean, P. H. Johnson

Hydrochloric acid , sulfuric acid , and chloridizing roast- water leaching methods for dissolution of cesium and rubidium from Maine , Canada , and Southern Rhodesia pollucite ores and their flotation products were investigated by small- scale tests . Optimum conditions were determined to be ( 1 ) for hydrochloric acid leaching , use 12.7 equivalents of 8.8 normal acid per equivalent of cesium in the sample and leach for 6 hours at 100 ° C ; ( 2 ) for sulfuric acid leaching , use 12.7 equivalents of 14.4 normal acid and leach for 2 hours at 120° C ; and (3 ) for chloridizing roast - water leaching , roast minus 200 - mesh ore, limestone , and calcium chloride in a ratio of 2 : 4 : 1 , respectively , for 1 hour at 900 ° C , and leach the calcine for 1 hour at 80 ° C with enough water to give 35 pct solids . Extractions of cesium from ores and flotation products containing over 20 pct cesium were in excess of 97 , 93 , and 96 pct for the hydrochloric acid , sulfuric acid , and chloridizing roast - water leach processes , respectively .

Jan 1, 1964

By Frank D. Lamb

"INTRODUCTION The use of beryllium and its alloys has come into prominence in the last 15 years and increased considerably during the war. In contrast to other light metals, such as aluminum and magnesium, beryllium is relatively hard, has a high melting point (1,285° C.), and other properties that make it resemble steel in many respects. It has a specific gravity of 1.85, is only slightly heavier than magnesium (specific gravity 1.74), and is appreciably lighter than aluminum (specific gravity 2.7). Its lack of ductility prevents its use as a structural material, but this difficulty may be overcome in the future by the use of various alloy forms. The only important commercial alloy in which beryllium is used today is with copper. The addition of small percentages (1/2 to 2 percent) of beryllium to copper imparts properties to the alloy that make it desirable for use in springs carrying electrical current, particularly at high temperature. Many other uses of berylliam are known, and new uses are being found constantly that make the metal of increasing interest.Possibly the main factor preventing the use of more beryllium is the lack of a large source of beryllium ore. Many beryllium minerals are found as minor constituents of natural deposits, some of the more common ones being beryl (Be3Al2(Si03)6), chrysoheryl (Be A1204), helvite (3(Mn, Fe) Be Si04. MnS), and phenacite (Be2Si04). Of the known beryllium minerals, beryl is by far the most common and has been found distributed rather widely throughout the world. It usually occurs associated with granitic rocks and is commonly found as a constituent of granitic pegmatite."

Mar 1, 1947

By Michael Hood

High-volume, low-pressure water jets have been employed for erosion of loosely consolidated rocks for centuries. This excavation method finds application in specialized circumstances even today. The use of high-pressure, low-volume water jets for rock cutting is more recent and was made possible by the development of high-pressure water pumps. Despite the benefits often claimed for these systems, high-pressure water jets still have not found widespread application. In this report, the U.S. Bureau of Mines has reviewed the various methods that have been employed using water jets to break rock and has focused on one method, termed "jet-assisted cutting," which was determined to be the closest to commercial development. The current state of knowledge based on laboratory and field experiences using this cutting method is reviewed, and possible future developments for this approach to excavation are assessed.

Jan 1, 1990

This project, "Analysis of Men, Materials and Supplies Handling Systems in Underground Metal and Nonmetal Mines" documents the productivity and safety aspects of the existing equipment and systems utilized in transporting personnel and supplies from the surface to the underground production work place. The Present Systems Study (this text -Volume II) documents the productivity and safety of existing men and material movement systems for six representative underground metal and nonmetal mines. Identification of common problem areas was performed using recognized industrial engineering techniques. The back-up data for the industrial engineering analysis of each mine is included as respective appendices (Volume III). A summary of the study background material, six mines' problem areas, comparison of problem areas, problem analysis, and solution recommendations are included as the project final report (Volume I), bound under separate cover.

Jan 1, 1975

By A. Wahab Khair

"This paper presents an analysis of fracture mechanisms in coal subjected to bi-axial state of stresses, indentation of laterally confined coal specimen. Coal specimens were loaded to failure by the straight wedge indenters at various lateral confinement pressures. Strain distribution and acoustic emission characteristics of coal specimens under stress were recorded. The influence lines of vertical forces acting on the horizontal straight boundary of the coal specimen for each type of wedge indenter have been established using holographic interferometry technique. The effects of wedge indenter angle, confinement pressure, and coal anisotropy on fracture types, failure modes, and post-failure conditions were studied. The results indicated that combined application of holographic interferometry and acoustic emission monitoring techniques is not only suitable ·for studying deformability of heterogeneous and microscopically discontinuous material under stress but it also enhances the mode of fracture during the post failure stage. INTRODUCTIONOne of the relevant processes in the coal cutting technology is the application of indentation theories. Since most cutting tools in the coal industry are wedge shaped most of the indentation research is found for a wedge shaped tool.A wide range of behavior is found in different rocks subjected to the wedge penetration. A rock which is elastic brittle at standard pressure might become elastic plastic at high confining pressure (Gnirk and Cheatham, 1963). It was also observed that some rocks will merely be crushed and indented by a wedge whereas others will crack and form chips, furthermore the existence or non-existence of chips depends mostly on the geometry of the indenter, type of rock and the depth of penetration (Evans and Murrel, 1958). However, coal cutting technology is mostly explained by models which use rigid wedge to penetrate into a brittle material in which both crushing and chipping will occur (Evans and Murrel, 1958, 1962)."

Jan 1, 1988

By E. S. Leaver

Experiments dealing with the dissolution of silver by cyanide from various silver minerals were reported several yews ago.4/ This work showed that the silver in some silver minerals is completely and readily soluble in cyanide solution, whereas other silver minerals must be given special treatment before or during cyanidation to obtain much dissolution of the silver by cyanide. Flotation as a method for treating silver ores has not been studied much, except in the case of base-metal ores carrying silver, particularly lead-silver ores. However, many mills now are concentrating gold ores by flotation, and when such ores also contain silver the recovery of the silver by flotation is of considerable importance. Moreover, many mines contain ore in which silver is the principal valuable constituent. Some of these ores are amenable to cyanidation, but the cost of a cyanide plant may be prohibitive because of limited ore bodies or other factors. In such instances the successful application of flotation would mean that the property could be operated.

Jan 1, 1939

By P. S. Haury

"INTRODUCTION Many ore deposits were discovered in the Wallapai Mining District, which covers the Cerbat Range in Mohave County, Ariz., during the early period of mining there from about 1865 to the 1890's. A considerable amount of production was obtained from shallow lead carbonate ores that carried considerable gold and silver.Mining was revived in 1906 and again during the First World War, and soma of the mines were deepened into the underlying sulfide zone. Substantial quantities of metal were recovered from two mines, the Golconda and the Tennessee-Schuylkill, that were, developed to depths of 1,600 and 1,400 feet, respectively. The Golconda is credited with $6,500,000 gross productions. 2/ This mine was not operated after 1917. The Tennessee-Schuylkill is still operating after a yield of about 300,000 tons of ore that averaged 4.33 percent lead and 7.74 percent zinc and contained an appreciable amount of gold and silver.Many of the old mines were reopened in 1942 or 1943 under the stimulus of premium prices for lead and zinc. A large proportion of this work was finished with loans from the Reconstruction Finance Corporation. It was believed that a good deal of lead and zinc could be recovered from the mines if a custom mill for concentration of the ores was available locally."

Aug 1, 1947