Search Documents

By Alla D. Mah

The heat of formation of scandium sesquioxide (Sc203) has not been measured previously, and existing values for gallium sesquioxide (Ga203) are subject to large uncertainties. As a consequence, thermodynamic calculations involving these oxides hare lacked scientific exactness. This paper reports newly determined values of the heats of formation of gallium and scandium sesquioxides at 298.15° K., by combustion calorimetry. The corresponding free energies of formation are derived from heat and entropy data.

Jan 1, 1962

By Constantine C. Popoff

This report reviews and analyzes, by a simple analytical and logical reasoning, the conventional methods of reserve computations of mineral deposits described in various domestic and foreign publications. It brings together, formulates, and evaluates the principles underlying interpretation of exploration data; and ties such principles to the proposed classification of methods. The material is discussed in sufficient detail to allow general application.

Jan 1, 1966

By H. H. Storch

"INTRODUCTION The first paper of this series contained data concerning the behavior of polyhalite (K2S04.MgS04.2CaS04.2H20) upon calcination and subsequent leaching with water at 100° C. It was found that upon heating polyhalite to temperatures between 298 and 500° C. the water of crystallization is driven off, leaving, an amorphous mixture of K2S04, MgS04, and CaS04. Two transition points were located; one at 298° C. which coincides with the vigorous evolution of steam; and one at 551° C. which results in the formation of a hard mass of crystals. The latter probably consist of a solid solution If the compounds langbeinite (K2504, 2MgS04), potassium dicalcium sulphate (K2304. 2CaS04), and anhydrite (CaS04). The heat of decomposition of polyhalite at 298° C. was measured and found to be 66,000 ± 5,000 calories per mol. The optimum temperature of calcination with regard to subsequent extrac¬tion with two parts of water (at "" 0° C.) is 430 to 450° C. for 65 to 100 mesh material, if one half hour at the calcination temperature is allowed. The maximum concentration of K2S04 obtainable in the extraction of calcined polyhalite is 11.4 grams per 100 grams of water. This concentration of K2304 is considerably above the equilibrium value (3.6 g. per 100 L. of H20 at 83° C.) with respect to the solid phases polyhalite, potassium calcium pentasulphate, ¬and anhydrite. The figure 11.4 K. of K2804 per 100 g. of H20 is also somewhat than the equilibrium value (9,65 g. per 100 g, H20) with respect to the solid phases potassium calcium pentasulphate and syngenite."

Oct 1, 1930

"These tentative coal mine inspection standards have been prepared as a guide for the Federal inspection of coal mines of the United States. Much time and thought have been spent by various members of the Safety Division in the preparation of thses standards, and it is believed that compliance with them eventually will be possible in most mines. In many instances objections will be raised to them owing to long-established mining customs and practices that are inherently of dubious safety and to a natural inclination to oppose change. In other instances there will be valid objections due to conditions not foreseen at the time these standards were prepared. Or there may be substandard conditions and practices due to original mine layouts that it is not practicable to change during the lifetime of the mine; in such instances it is likely that some effective measures are or can be taken toward lessening hazards.With the rapid change in mining methods some of the standards may become inapplicable and it may be advisable to revise them to meet the new conditions. Therefore, questions regarding these standards and suggestions regarding new standards should be brought to the attention of the supervising engineer of the Coal Mine Inspection Division so that modifications of and additions to these standards may be made from time to time.In many respects these standards exceed the provisions of the various State mining laws, and some may conflict with the laws of some States. In cases of conflict, the intent is not to advocate noncompliance with State laws but to suggest that it may be desirable for the State to reconsider such laws or safety orders.Although an effort has been made to word these standards so that they may be readily understood, nevertheless, a reasonable interpretation should be placed upon them. In fact, in numerous instances the words reasonable"", ""suitable"", and ""properly"" are used in recognition of the fact that reason- and sound judgment enter into the carrying out of the safety endeavor.The policy of the Bureau on some vitally important safety matters in mines is set forth in its published Safety Decisions. These decisions have been consulted and used in the preparation of these standards. These decisions also are now being reexamined by its Mine Safety Board."

Feb 1, 1942

By R. L. Benner

The Bureau of Mines investigated the ZnO-Fe2O3-Fe3O4 system at 1,000°, 1,300°, and 1,400° C, with oxygen pressures between 1.0 and lx10-4 atmospheres. The results, divided into the thermodynamic properties as related to the spinel structure, and the thermodynamic properties as related to zinc concentrate roasting, were used to calculate the activities of ZnO, Fe2O4, and Fe3O4 within the spinel solid solution region of the ternary system, and the pseudo-binary activities of ZnFe2O4 and Fe304. The activities of both systems show large positive deviations from Raoult's Law, especially at high Fe3O4 concentrations. The free energies, the enthalpies, and the entropies of mixing for the binary system were calculated from the binary activities, and the entropies of mixing were compared with two statistical models, one representing an ideal solution, and one representing the mixing of a normal with an inverse spinel. The binary entropy of mixing seemed to be better represented by the latter statistical model, indicating that the tetrahedral and octahedral cations of the reactants tend to remain in the product, even at the high temperatures of the study. This comparison also indicated that the cations of the components are the major contributing factors to the thermodynamic properties.

Jan 1, 1966

By Walter K. Utt

The process of drilling and bolting the roof is currently one of the most dangerous jobs in underground mining, resulting in about 1,000 accidents with injuries each year in the United States. To increase the safety of underground miners, researchers froth the Spokane Research Laboratory of- the National Institute for Occupational Safety and Health are applying neural network technology to rite classification of mine roof strata in terms of relative strength. In this project, the feasibility of using a monitoring system on a roof drill to assess the integrity of a mine roof and warn a roof drill operator when a weak layer is encountered is being studied. Using measurements taken while a layer is being drilled, one can convert the data to suitably scaled features and classify the strength of the layer with a neural network. The feasibility of using a drill monitoring system to estimate the strength of successive layers of rock was demonstrated in the laboratory.

By Larman J. Heath

Wellbore enlargement was tested using hydrazine hydrate in a gas-storage well in Ohio to increase the well productivity. The wellbore was to be enlarged by chemical disaggregation of the sandstone adjacent to the wellbore. Productivity immediately declined 49.1 percent and gradually declined to zero in 7 months. A down-hole camera survey showed a white-to-gray precipitate covering the entire wellbore surface. The precipitate was chemically analyzed and identified as mostly carbazic acid, a hydrazine derivative of carbonic acid. Formation of this precipitate was not anticipated; this viscous sub-stance caused the gradual loss in productivity of the well. The wellbore was not enlarged. Laboratory tests were run to determine what clay stabilization measures could be taken in sandstone cores to prevent clay swelling and particle migration caused by hydrazine hydrate. Normal clay stabilization methods did not prevent the virtually complete loss in permeability to hydrazine hydrate. Other laboratory tests using natural gas diluted with small amounts of carbon dioxide confirmed the ease with which carbazic acid could be formed in a hydrazine hydrate-saturated environment within and adjacent to the wellbore.

Jan 1, 1970

Airy kind of a power system is a complicated network of various electrical components, such as cables, transformers, electric machines, circuit breakers, etc. For a system to work continuously and efficiently, each of the components has to be in perfect operating condition. The failure of any of these components can cause serious interruption of the supply and may in several cases involve a lot of precious time and labor in removing and replacing the damaged equipment it may also give rise to dangerous overvoltages on the system, thereby causing a safety hazard. Any piece of electrical equipment can have two likely modes of failure. The first would be the degradation of solid insulation material due to overheating, mechanical damage or a combination of the two, In this mode of failure it is possible that If the insulation damage is not an instantaneous phenomenon (a cable damaged by severe mechanical, Stress) that a detectable leakage current will do lop prior to the faint. The fault would probably he a result of heating and deterioration of the insulation by the leakage current.

Jan 1, 1975

By Alex C. Smith, Thomas A. Gray, Lynn M. Crayne, Michael A. Trevits, Phil Glogowski

Mine fires constitute one of the greatest threats to the health and safety of those working in the underground environment and each event has the potential for disastrous consequences. Of the major mine fires and thermal events that have occurred in the United States in the last 6 years, it is estimated that remotely installed seals could have been used in 63% of the events to control fire growth or to aid in fire suppression work. The National Institute for Occupational Safety and Health (NIOSH) is conducting full-scale tests at the NIOSH Lake Lynn Experimental Mine to evaluate and improve remote mine seal construction technology. The main focus of this work is to develop reliable technology that will completely close the mine opening from floor-to-roof and rib-to-rib. This paper presents the results of remote seal installations using grout-based materials.

By R. P. Maloney

Since mining operations began in 1900, Government geologists and mining men have periodically recorded the presence of the minerals of mercury and antimony in the extensive gold placer deposits near Flat in the Iditarod district of the Yukon River region, Alaska. No serious effort was made to recover the cinnabar contained in the gold placer gravels, and there is no evidence that veins of cinnabar and stibnite exposed in the placer operations (as reported by the Geological Survey) were ever explored or developed. A large monzonitic intrusive, which is the dominant geologic feature of the immediate area, is believed to be the lode source of the valuable minerals in the placer deposits. In contact with the monzonite are argillite and quartzite, metamorphic products from the Cretaceous shales and sandstones.

Jan 1, 1962

By Sidney Katell

This Bureau of Mines study estimates capital investment, operating costs, and selling prices for three underground bituminous mines producing coal with annual production ranging from 1.03 to 3.09 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes Initial capital investment ranges from $26,498,500 for the 1.03- million-ton-per-year (MM tpy) mine to $67,173,300 for the 3.09-MM-tpy mine. Total capital investment ranges from $37,437,500 to $92,984,300 for the same mines. Corresponding selling prices for the coal range from $14.83 to $13.26 per ton, assuming a 15-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1975

By Joseph Grumer

Theory pertaining to the exchangeability of fuel gases on appliances has been extended to exchanges of propane or butane with mixtures of these. In particular, new considerations were developed bearing on the hazard of an occasional emission of carbon monoxide and flashback and blowoff possibilities. The new considerations involve using current requirements for approval of liquefied petroleum gas appliances. These requirements were used to predict allowable tolerances in chemical composition of liquefied petroleum gases for existing appliances. In addition, changes in gasline pressure were computed which may be substituted in place of fuel exchanges during testing of appliances,

Jan 1, 1962

By H. C. Fowler

The social economy, or public interest, and national defense require wise development and efficient use of the oil and gas resources of the United States. In this development and use, and in the prevention of economic and physical waste of oil and gas, the objectives of the petroleum and natural-gas industries, the Government (Federal, State, and local), and the public are the same. Differences of viewpoint generally have originated in the failure of one of the triad to have a clear or complete understanding of the motives behind the activities of the other component groups or full knowledge of what each is trying to accomplish. The Unites States Bureau of Mines through its petroleum and natural-gas division makes technologic and scientific investigations pertaining to recovery,3 preparation, refining, and use of oil and natural gas with the view of reducing waste, increasing safety and efficiency and aiding economic development.

Jan 1, 1933

By Lincoln A. Stewart

"INTRODUCTION The First Supplemental National Defense Appropriation Act, approved August, 25,, 1941, authorized the Bureau of Mines to investigate sources of raw, material for western production and appropriated funds for that purpose. Numerous iron deposits and prospects in the Western States were investigated. Among those selected for more detailed investigation were tile Apache and Chodiski deposits in Arizona.The United States Geological Survey had examined these deposits in 1929 3/ and estimated that ""the quantity of minable ore reasonably to be expected in this locality will reach 10,000,000 long tons, but it will require prospecting by core drill to demonstrate this quantity with certainty"". C. H. Johnson, a mining engineer of the Bureau of Mines, made a preliminary examination in October 1941 and proposed exploration of the Apache deposit Canyon Creek.A trench sampling project was set up, and work at the Apache deposit commenced in November 1941. Mapping, trenching, and sampling of outcrops was completed in March 1942. Trenches were laid out at approximately 200-foot intervals for about 9,200 feet along the iron outcrop east of Canyon Creek, and channel samples were taken across the iron formation. The outcrop also was explored by trenching and sampling along a 1,900-foot outcrop on the west side of Canyon Creek.The first diamond-drilling campaign at Apache was initiated in May 1942 and continued to January 1943, when work was suspended owing to depletion of funds. Six holes spaced at approximately 500-foot intervals and, 500 feet back from the outcrop on the east side of Canyon Creek were drilled through the iron formation during this period.While this drilling was in progress, the Chediski deposit was mapped, trenched, and sampled. The trenches were spaced at intervals of approximately 800 feet along 10,000 feet of the iron-ore outcrop."

Jul 1, 1947

By Kray Luxbacher, Mario Karfakis, Erik Westman, Peter Swanson

Three-dimensional velocity tomograms were generated to image the stress redistribution around an underground coal longwall panel to produce a better understanding of the mechanisms that lead to ground failure, especially rockbursts. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Eighteen tomograms were generated and high-velocity regions correlated with high abutment stresses predicted by numerical modeling. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated, indicating that velocity tomography may be an appropriate technology for monitoring stress redistribution in underground mines.

By Eric S. Weiss, Deno M. Pappas, Timothy M. Barton

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has been evaluating developments in sealant support systems from a ground control perspective. The proper selection and use of a sealant material can significantly enhance ground control which may result in a decrease in worker related injuries due to ground falls. The purpose of this paper is threefold: to briefly review the current state-of-the-art technology in shotcrete and membrane developments, to evaluate the preliminary findings of a long-term underground study of various types of sealant materials, and to examine installation practices that are critical for an effective sealant material. The underground study utilizes NIOSH’s Lake Lynn Laboratory Experimental Mine to evaluate the long-term performance of several types of shotcrete and membrane materials. Sealant performance to date have been evaluated on a regular basis over a two year period. Although the study is still ongoing, critical mining practices were identified that may seriously effect the bond of the sealant materials to the mine roof and rib; most notably, the importance of scaling and thorough cleaning of the rib prior to application. Also, results froman extensive series of Schmidt Hammer tests found that the shotcrete increased in strength by 70% during the humid summer months.

By Albert W. Deurbrouck

This Bureau of Mines report describes the washability characteristics of 13 coalbed samples collected in Colorado. Such data are needed to evaluate the quality of the coals of the West, where most of our low-sulfur-content coal reserves are found. Of the 13 samples included in this report, 11 had a total sulfur content of 1 percent or less. All of the samples contained low percentages of ash or could be readily washed to a desirable ash level with minimal loss of yield. The coals ranged in rank from high-volatile A bituminous to subbituminous B; nine of the samples were high-volatile C bituminous. The coalbeds ranged in thickness from 6 to 26 feet; the average was about 8 feet.

Jan 1, 1970

By T. T. Read, F. C. Houghten

"The bad effects upon the health and output of miners that result when the ventilating current in a mine lacks sufficient cooling power have been described by Harrington and Sayers in a previous report (1)*** The normal temperature of the human body is about 98.5°F. and whenever work is done by the muscles, indeed even when sitting still, the normal bodily processes generate heat which must be given off, otherwise the body will become overheated and a number of bad effects will be produced. If it were possible to so enclose a man that he could continue to breathe and no heat could escape from his body he would die within a short time. In a series of experiments made at the Pittsburgh Station of the Bureau of McConnell and Houghton (2) found that a dry-bulb and a wet-bulb temperature of 112.5°F could he borne for only 35 minutes, even when the subject was at rest. A wet-bulb temperature of 100.4°F (dry-bulb 157°F) could only be tolerated for 45°F minute. Under such conditions the bodily temperature rises as much as 45°F above normal and the pulse is accelerated. Very uncomfortable sensations are felt when the pulse rate exceeds 135. The human body, like any other internal combustion engine, must be cooled in order to function properly.Under ordinary circumstances the air surroundings people is enough coder than themselves to permit this heat generated within the boiy to be river off with¬out difficulty. At higher temperatures, or when the rate of work, with its corresponding generation of heat is high, the body can not throw off heat fast enough, so it begins to sweat and the evaporation of the sweat cools the body. But the results of the experiments cited above indicate that in still air, even with the body at rent, it can not adjust its temperature when the air is above 90° wet- bulb. J. S. Haldane (4) says ""at a wet-bulb temperature of 60°F the actual amount of work done by the miner begins to fall off; as the wet bulb temperature rinse farther the work Bona gradually diminishes to the vanishing point. Then the temperatures indicated by the wet-bulb exceeds 85°F hard work in a mine seems hardly or the commercial working of a mine the wet-bulb thermometer should not in generaI, be allowed to rise above 80°F, unless perhaps where there it a good current."

Dec 1, 1923

By R. A. Franks, G. F. Friel, J. C. Edwards, A. C. Smith

An evaluation of a nuisance-emissions-discriminating smart mine fire sensor system was made in an operating coal mine. These field evaluations were conducted to determine the sensor system's ability to discern nuisance emissions, such as diesel exhaust, emissions from flame cutting and welding operations or hydrogen gas from a charging station, from real fires and to compare the number of falsely reported fire alarms generated between the sensor system and a standard carbon monoxide (CO) monitor. The sensor system's ability to operate successfully in the working environment of an operating coal mine was also evaluated. The smart mine fire sensor system consisted of four sensors whose data outputs were fused with the use of a neural-network-type computer program. Long-term trials were conducted in a haulage way, a belt entry, and a track entry. The system functioned successfully in the belt entry, in accordance with its developmental goals, where the sensor system even discriminated events not anticipated during development. It was not totally effective in the haulage way and track entry, though, due to a combination of significant diurnal air temperature variations, dust, and mechanically induced vibrations. Also, deteriorating rib conditions contributed to operational problems in the haulage way evaluation. In general, the smart mine fire sensor provided nuisance emissions discrimination and was shown to be a viable new approach for mine atmospheric monitoring, enhancing miner safety. This paper describes the in-mine evaluation of the smart mine fire sensor system and discusses recommendations for improving the system.

By H. A. Doerner

"Statistics show3 that in 1927 the United States consumed 60 per cent of the world's production of chromite and produced none. The uses of chromium are rapidly expanding, and a dependable supply is essential to our industries. Since the political and commercial control of our supply of chromite is now in foreign hands it is prudent to determine how this nation can best prepare to supply its need for chromium if the imports were cut off or restricted and whether it is now possible and desirable to stimulate production of chromium from domestic deposits. We have only small amounts of chrome ore of high enough grade to meet present trade requirements. Therefore the Bureau of Mines is making a study of methods for beneficiating our low-grade ores.Chromite (Cr203.Fe0), is the only commercial source of chromium. For refractories, a minimum of 40 per cent Cr203 and a low silica content (5 to 8 per cent) is usually specified. In most instances bricks or lumps having a physical structure that will not crack when heated are required. The only way an inferior ore could be adapted to this use world be to concentrate it and develop a satisfactory binder to make bricks out of the concentrates.For making ferrochrome the requirements are a minimum of 45 per cent Cr203 and an iron content not exceeding one-third of the chromic oxide. On some low-grade ores gravity concentration will give a product meeting these requirements; other ores yield concentrates containing too much iron or other impurities to be saleable."

Jun 1, 1930