Search Documents

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 64 to 10,000 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

By Robert J. Hundhausen, Robert M. Gammell

"INTRODUCTION Several mining properties in the Pine Creek area of the Coeur d'Alene mining region of Idaho were examined by engineers 3/ of the Bureau of Mines in 1942. As a result, a broad program of exploration was recommended for the area, particularly in the eastern end, where chances for the discovery of new ore shoots seemed favorable. This report describes the work done and the factual information obtained by the Bureau of lanes.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell Be Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch,. C. C. Ralston, chief, analyzes samples and performs beneficiation tests.The exploratory work at the Sidney mine was part of the activities of the Albany Division of the Mining Branch, S. H. Lorain, chief. Field work was under the direction of R. M. Gammell.Chemical analyses included in this report were performed at Reno, Nov., under the direction of A. C. Rice, acting engineer in charge, Rare and Precious Metals Experiment Station, Bureau of Mines. The ore-dressing tests were made under the direction of S. R. Zimmerley at the Bureau of Mines laboratory in Salt Lake City, Utah.The cooperation and assistance given by the owners of the Sidney Mining Co. is gratefully acknowledged."

Feb 1, 1948

By S. H. Ash

The coal-mining districts of Washington are mainly situated west of the Cascade Mountains. The eastern boundaries of Whatcom, Skagit, Snohomish, King, Pierce, and Lewis Counties, shown in Figure 1, form the backbone of the mountain range. The mines are on the foothills of the slope and extend to the shores of Puget Sound in the central and northern portions. The subbituminous fields of Lewis, Thurston, and Cowlitz Counties extend into the valleys west of the mountains. The Roslyn field, a small but important area, Lies on the eastern slope of the Cascade Range. If western Washington is divided into three areas from north to south the bituminous coal fields and most of the active mining operations will be found largely in the central area. In the southern portion there are large areas of subbituminous coals of varying quality extending from Centralia to the Columbia River. In the northern portion, mining is at present practically restricted to one mine which is working a subbituminous bed near the city of Bellingham.

Jan 1, 1931

By Edward D. Thimons

Inflatable stoppings are currently marketed for production use, and numerous mining companies have become interested in using such stoppings in rescue and recovery operations. The Bureau of Mines therefore evaluated the concept of using inflatable stoppings in emergency situations. The stoppings tested by the Bureau were 12-foot-diameter spheres inflated with a blower operated by a small battery pack. Experiments were conducted with the stoppings in a full-scale wooden mine model to evaluate their ability to withstand sliding or slipping at various internal and differential pressures, puncture resistance, various inflation techniques; and internal leakage from the stoppings. The stoppings were then installed and tested in the Bureau's Safety Research Coal Mine at Bruceton, Pa., to determine their effectiveness as mine air barriers. Despite some encouraging results obtained with the model and in-mine studies, the stoppings did not perform well in two operating metal mines where they proved difficult to erect and inadequate as air barriers.

Jan 1, 1976

By Glenn C. Reed

This report is one of a series describing mineral investigations within the Missouri River Basin in Montana. The primary purposed of these investigations is to provide information to agencies of the Department of the Interior and others concerned with the planning of Federal power developments in the basin. This report is limited in score to consideration of mineral deposits of presumed inventory value within Gallatin County, Mont. The field investigations were made during the fall of 1948.

Jan 1, 1951

By M. R. Geer

The cleaning of fine coal, particularly for metallurgical use, is receiving greater attention. An increase in the proportion of fine coal in the run-of-mine product has been created by changes in mining practice, and a concur-rent deterioration in the quality of the fines has occurred because of more widespread full-seam mining. These two factors, augmented by the depletion of premium beds of metallurgical coal in some areas and the resulting shift to "dirtier" beds, are providing the impetus for adoption of improved cleaning techniques. For example, froth flotation, which has been used for years in a few preparation plants, now is gaining more rapidly in acceptance. Similarly, the dense-medium cyclone, which is used widely in Europe for making difficult separations, recently has been introduced to the United States. Regardless of the cleaning process employed, the finer sizes of coal can be treated with maximum effectiveness only when they are removed from the run-of-mine product and treated separately. No present process can treat the full range of sizes together with complete effectiveness. Flotation is applicable only to the coal finer than a top size ranging between 14-and 48-mesh, and cyclones require removal of all material finer than 0.5 to 0.3 mm. from the feed. Thus, the trend toward more-effective cleaning of the fine coal imposes the attendant problem of fine screening. Whereas in the past there was little need to screen finer than about l/4-in., present developments indicate that fine screening will become increasingly prevalent.

Jan 1, 1960

By A. E. Isaacson

Bureau of Mines researchers developed and tested equipment to measure corrosion rates on a commercial scale mill. Bench-scale experiments were designed for duplicating ore grinding conditions closely enough so that realistic rate determinations could be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1988

By John Nagy

A study was made in the Bureau of Mines experimental coal mine of factors affecting gas ignition by a cutoff explosive charge. Experiments showed that, although gas could be ignited under some circumstances, the probability under normal mining conditions would be low. The use of permissible explosives, relatively short-delay intervals in firing adjacent holes, blasting to a 6-inch kerf, and reasonable care in the placement of the holes favor safe blasting and are current practice in mining. The experiments also showed that the weight of the charge is not a primary factor in the ignition of gas by a cutoff charge. The quenching action of a first charge on the igniting action of a second was verified in a supplementary study. Related experiments have shown that gas at the face may be ignited by a single charge of explosive when fired with a light coal burden. Permissible explosives were less hazardous under these conditions than nonpermissible explosives. The frequency of gas ignition in cutoff and single-charge experiments increased as the linear distance between the sheared face and the opposing mine rib increased.

Jan 1, 1960

By T. E. Gray, A. W. Deurbrouck

This report describes the preparation characteristics of significant coalbeds in Kanawha County , W. Va . It is one in a series of Federal Bureau of Mines reports planned to determine coals suitable for producing metallurgical coke , either as mined or after beneficiation . Almost 9.4 million tons of coal was produced in Kanawha County , W. Va . , in 1959 , of which about 67 percent was cleaned mechanically in 10 cleaning plants . It has been estimated that more than 5,505 million tons remain in the county . Samples were collected from Pittsburgh , Stockton - Lewiston , Winifrede , Cedar Grove , Peerless , Upper Kittanning , Coalburg , Powellton , Eagle A , No. 2 Gas , and the Lower Kittanning beds . These beds were selected by the Bureau based on current production rates and estimated minable reserves . Float - and - sink tests of the samples collected from Eagle A , Peerless , Cedar Grove , Winifrede , and No. 2 Gas beds show that these coals at one location each are suitable for metallurgical use without washing . Lower Kittanning bed at four locations ; Pittsburgh , Stockton - Lewiston , and No. 2 Gas beds at two locations each ; and Coalburg , Powellton , Winifrede , Peerless , Upper Kittanning , and Cedar Grove beds at one location each can be upgraded to metallurgical quality by mechanical cleaning . Crushing the samples to 3/ 8- inch top size increased yields substantially at 1.30 specific gravity of Pittsburgh ( 17.5 percentage points ) and Upper Kittanning ( 13.0 percentage points ) beds and increased yield for the other beds sampled to a lesser amount . At this specific gravity , finer crushing caused In the 1.58 specific gravity float a general decrease in ash and sulfur . fractions of the other samples tested , most of the yields , and ash and sulfur contents , were lowered slightly by finer crushing .

Jan 1, 1963

A series of laboratory evaluations examined the impact of water spray pressure, curtain setback distance, and external and underboom spray use for controlling respirable dust levels and sulfur hexafluoride tracer gas concentrations around a continuous mining machine. This mining machine was equipped with a flooded-bed dust scrubber and was positioned in the box or slab cut. Exhaust line brattice was used for all tests. Dust levels were measured in the return airway and at locations representing the operators of the continuous mining machine and the standard and off-standard shuttle cars. Increasing water pressure or using the underboom sprays produced no significant impacts on dust levels, although their interactions did produce some significant impacts. Increasing curtain setback distance often elevated dust levels, likely by reducing the amount of airflow reaching the face. Use of the external sprays created additional airflow around the mining machine that pushed the dust cloud past the scrubber inlets. This significantly increased dust levels at all sampling locations. Tracer gas levels were measured on the off-curtain and curtain sides of the cutter head and in the return airway. Increasing water pressure generally led to significantly increased gas levels on the curtain side, although a slight decrease was observed on the off-curtain side with the machine in the box cut. Increasing setback distance elevated gas levels on both sides of the cutter head and in the return by limiting the quantity of ventilation airflow reaching the face. Use of the external sprays provided additional airflow along the off-curtain side of the machine, significantly reducing gas levels in this region. These sprays adversely impacted the dilution and removal of gas on the curtain side of the cutter head. Use of the underboom sprays adversely impacted gas levels on both sides of the cutter head. Use of the external sprays provided the best control of respirable dust and face gas concentrations. The smaller increases in miner operator dust levels produced by these sprays were offset by larger reductions in face gas levels on the off-curtain side of the cutter head. Although the underboom sprays minimally impacted respirable dust levels, use of these sprays was not recommended because they increased face gas levels.

Jan 1, 2007

By Barbee J. Scheibner

This Bureau of Mines report describes the geology and physical properties of core samples at the Sunnyside coal mine No. 1, Sunnyside, Utah, and was written in conjunction with the Single-Entry Program conducted at the mine. The objective of this program was to test the hypothesis that the single-entry system in the Sunnyside mine, supported in the center by open cribs and divided by a fire-resistant partition, is equivalent to or better than a two-entry sys-tem. Drill cores, taken underground at 15 sites in the single-entry study area, facilitated the construction of geologic cross sections of the entries. Physical property data obtained from the drill cores was used in a three-dimensional finite element analysis program to evaluate the stability of the openings, the support requirements, and the de formation characteristics of the roof and floor material. Data on 10 physical property parameters for 5 rock types plus coal are also tabulated and discussed.

Jan 1, 1979

By B. R. Mohal, F. F. Aplan, S. Chander

"The wetting behavior of coal has been determined in the presence of nonyl and octyl series of nonionic surfactants containing polyethoxy groups of different sizes. The wetting behavior was determined by a modified Walker technique and contact angle measurements. The results show that the wetting rate of coal varies with coal rank, structure of the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. A close relationship has been observed between the wetting rates and the short-time advancing contact angles.INTRODUCTIONNonionic surfactants are used in many applications to improve wettability of solids. They can be used as dispersing agents [ 1 ] or dust suppressants [ 2-5] and to control the flotation, flocculation, filtration and, flowability of particulates. This study was undertaken to study the effect of a series of nonionic surfactants on the wetting behavior of coal. Two series of surfactants, namely, ethoxylated nonyl and octyl phenols were used. The nonyl phenol series con tains a linear hydrocarbon chain containing nine carbon atoms (CH3 ( CH2 )8-C6H4- ( OC2H4 ) n, where n is the number of ethoxy groups) . The octyl phenol series contains a branched hydrocarbon chain containing eight' carbon atoms ( ( CH3 ) 3CCH2C ( CH3) 2-C6H4- ( OC2H4 ) n ).Initial wetting rates — modified Walker techniqueWalker et al. [ 6 ] developed a sink test to determine the wettability of coal particles. In this technique, coal particles are dropped individually onto the surface of surfactant solutions of different concentrations, and the most dilute concentration in which coal would sink ""instantaneously"" is determine& This technique is a variation of a procedure initially developed by Draves and Clarkson [ 7 ] to determine the effect of surfactants on wettability of cotton fibers."

Jan 1, 1989

By John F. McCoy

The U.S. Bureau of Mines (USBM) awarded? a contract to Foster-Miller, Inc. to develop guidelines for designing, constructing, stocking, and maintaining rescue chambers in underground mines. This report develops information and recommendations which could be used by a mine operator who desired to install a rescue chamber. Volume I covers the following major areas: atmospheric life support, configuration and construction, chamber location, power and lighting, equipment and supplies, communications, and psychological aspects and training. Volume II contains the following appendices: History of Barricading, Chamber Pressuriztion Considerations, Diffusional Infiltration of Gas, Compressed Air Storage, Location Examples, and Psychological Aspects.

Jan 1, 1983

By Jack L. Henry

A laboratory and a pilot-plant-scale investigation has been conducted by the Bureau of Mines to examine possible sources of nitride defects in the production of magnesium-reduced titanium sponge. The production of alpha-stabilized nitride inclusions in hot-rolled titanium plate from air contamination of sponge during its manufacture has been experimentally demonstrated. Magnesium-reduced sponge prepared from air-contaminated magnesium or when contaminated by an air leak during reduction, vacuum distillation, or inert gas sweep, shows very large variations in nitrogen content. Refractory nitrides, delta TiN and epsilon Ti2N have been identified in this sponge. The highest incidence of inclusions resulted from sponge that was reduced by air-contaminated magnesium and from sponge subjected to air contamination during the vacuum distillation cycle and during helium sweep. Air contamination of sponge during the reduction cycle was not nearly as effective in producing inclusions. Tests showed that color and texture may not be reliable criteria for locating defects during sponge inspection. Maintenance of good vacuum-tight integrity, filtration of molten magnesium prior to charging into the reduction retort, and mechanical attrition of sponge to pulverize and disperse nitrides are suggested as practices to lower inclusion incidence in commercial titanium ingots.

Jan 1, 1974

By Jos. R. Guiteras

This paper is one of a series published by the Bureau of Mines on mining and milling methods and costs. It describes operations in the Alma district of Colorado in September 1937, supplemented by some additional data collected in July 1938. ACKNOWLEDGMENTS The author wishes to express his appreciation of the friendly cooperation extended him by the mine operators in the district. The greater part of the information was obtained from mine and mill superintendents to whom individual acknowledgment is made in the text.

Jan 1, 1940

By O. M. Bishop

"INTRODUCTION Early in World War II, the Bureau of Mines realized that reserves of fluorspar ore at many mines in the southern Illinois fluorspar district were not being developed as rapidly as the old ones were being depleted. At some mines the measured and indicated ore reserves were almost entirely depleted, although geologic factors favored new discoveries. The Leo mine, which had not been worked since 1938, was among this group of mining. The Bureau of Mines, together with the Illinois Geological Survey examined the property, studied the mine records and,geologic factors in 1944, and agreed that exploratory drilling was warranted Funds were,obtained for the work in the fiscal year 1945, and drilling was done; between October 27, 1944, and June 15, 1945.The property was owned in fee simple by the Hllside Fluor Spar Mines at the time exploration was begun in October 1944. Subsequently, in 1945, the Inland Steel Co. acquired of the Hillside property."

Jan 1, 1947

By C. C. Furnas

Despite the fact that a great many industrial processes depend on efficient contact between a gas stream and a bed of broken solids for their operation, the data in the literature are very meager. Several investigations3 have been undertaken, but the work has been limited in scope and application. BUREAU OF MINES PROGRAM OF RESEARCH For the past 10 years the United States Bureau of Mines has been engaged in research with the object of formulating a more or less complete quantitative theory of the workings of the iron blast furnace. Obviously, in order to do this one of the essentials is to have considerable definite information on the laws of gas flow through beds of broken solids. This report in a brief summary of the experimental work on the problem which has been done at the North Central Experiment Station. The complete report with more detailed tabulation of the data and explanations of the experimental procedure is in process of publication in the form of a bulletin.

Jan 1, 1928

By A. B. Hooker

Gassy mines require daily inspections with methane detectors to test for the presence of methane. Although in many manes it may be sufficient to know that there is no methane present or that its percentage is below a certain amount, it is desirable and often necessary to determine definitely the percentage of methane at the working faces and in the various air currents. The Bureau of Mines recognizes two general types of portable methane detectors, namely; 1. Methane detectors by which the presence of methane may be detected and its approximate percentage estimated.

Jan 1, 1929

By Joseph Grumer

The range of composition of gases synthesized from solid fuels which are exchangeable with natural gas on current gas appliances was evaluated by theoretical principles. These principles consider primarily the flashback, blowoff, and yellow-tipping characteristics of air-entraining burner flames. It was found that complete identity between the synthetic and natural product is not necessary. Gases such as may be obtained by hydrogasification of coal and other solid fuels without the removal of unreacted hydrogen offer advantages in flame characteristics. Between 25 to 37 percent hydrogen can be tolerated in the sendout gas.

Jan 1, 1965

By John J. Henn

An evaluation is presented of the Bureau of Mines process for the recovery of metal and mineral values from municipal incinerator residues. This process employs standard mineral beneficiation techniques and is operating on a pilot-plant scale of 1,000 pounds of incinerator residue feed per hour. Products from this separation process include ferrous, aluminum, and copper-zinc scrap, and colorless and colored glass. Cost estimates were prepared for four plant sizes. The estimated capital and operating costs For the four plants follow: [ ] It is assumed that the separation plant is located adjacent to a municipal incinerator. Provision is made, however, for part of the residue feed to be delivered by truck so that one large separation plant can be used for residue from more than one incinerator.

Jan 1, 1971