Search Documents

By L. P. Kleinmann

To control the formation of acid drainage at its source, the Bureau of Mines has investigated the role of iron-oxidizing bacteria in the oxidation of pyrite. In laboratory tests, it was determined that Thio-bacillus ferrooxidans could be controlled in coal refuse using anionic surfactants, with an associated decrease in acid production of about 75 pet. Based on these results, large-scale tests were conducted at an 8-acre active coal refuse area in northern West Virginia and an 11-acre inactive refuse pile in southern West Virginia. Acid production was decreased 60 to 95 pet for 4 to 5 months after application of 55 gal/ acre of 30-pct sodium lauryl sulfate solution. To date, effluent surfactant concentrations have been extremely low. Either a hydroseeder or a road-watering truck can be used to apply the surfactant. Since the surfactant solution must reach the pyritic material to be effective, sites that have been reclaimed are generally not amenable to these procedures. A simple laboratory test is described that provides an estimate of adsorption potential; this can be used to calculate a safe application rate.

Jan 1, 1983

By Joseph W. Horne

This report presents the results of an investigation by the U. S. Bureau of Mines in cooperation with the State of Colorado, on the yields and properties of oils produced from oil shale, lignite and subbituminous coal using the standard assay method developed by the Bureau for oil-shale testing,. The purpose of this work, which is part of the general study of oil shales being conducted by the Bureau of Mines and cooperating agencies, was to obtain information on the amount and character of the yield of crude oil or tar from different typical oil shales, the yield of light oil or naptha that might be suitable for use in motor fuels, and other products of shale oil. As the west has large resources both of oil shale and low-grade non-coking coals, it is of interest to know the relative yields of tars, light oils, and combustible gases that can be produced from these coals when retorted under conditions similar to those suited for oil-shale retorting. Source of Samples The coal samples were obtained from deposits on or adjacent to the public lands in the States of the Rocky Mountain region. Many of the mines sampled are operating under Government leases or permits. The number of coal samples secured from the various states are: Colorado, 6; Montana, 9; north Dakota, 6; New Mexico. 1; South Dakota, 1; Wyoming, 9. Of these samples, 14 were lignite coal, 16 subbituminous coal, and a bituminous coal. The standard channel method of the Bureau of Mines was used for sampling. Coal samples received at the Boulder Office weighed about twelve pounds each, and duplicate samples were sent to the Pittsburgh Station for proximate and ultimate analyses. The origin of the samples and description of the deposits are given in Table 1.

Jan 1, 1927

By L. B. Pankratz

Thermodynamic data on the sulfides were reviewed, evaluated, and compiled at the Bureau of Mines Albany Research Center. Values for Cp°, S°, H°298 -(G° - H°298)/T, ?Hf°, ?Gf°, and log Kf are given in tabular form. Cp°, H° - H°298, ?Hf°, and ?Gf° are also expressed algebraically.

Jan 1, 1987

By T. J. Rohrbacher

This report presents a U.S. Bureau of Mines methodology developed to incorporate factors of coal production (mining and cleaning methods, recoveries, economics, etc.) into the definition of recover-ability of a coal resource. Project procedures and computer models that were developed to include mine and preparation plant production rates, recoveries, and costs are explained. The results of these procedures and models are reviewed and compared to the Energy Information Administration estimate of U.S. coal resources-the "demonstrated reserve base." The Matewan 7-1/2-minute quadrangle in eastern Kentucky was selected to demonstrate the methodology.

Jan 1, 1993

By Robert F. Randolph, Jeffery L. Kohler, David C. Byrne

Multiple versions of an educational message can reach a diverse population more effectively than a single version. For instance, some workers are trained in formal classrooms while others are self-taught. The National Institute for Occupational Safety and Health has developed multiple versions of a hearing loss simulator (an interactive software package, a Web-based module, and an electronic slide show) to show how a single set of information can be readily adapted to different delivery methods. The three versions of the simulator were developed with a minimum of effort and expense compared to a single, less-flexible version. The interactive software is best for training sessions led by a hearing conservation professional, the Web pages are best suited for an individual worker, and the slide show is best for a small, more-generalized, training class. This paper will describe additional advantages and disadvantages of different delivery systems and will show what considerations are helpful in designing content that can be readily adapted to alternate presentations.

Jan 1, 2002

By George S. Rice

"""To prevent the propagation of mine explosions, the Bureau of Mines, Department of Commerce, recommends rock-dusting all coal mines, except anthracite mines, in every part, whether in damp or dry condition. It also recom¬mends that rock-dust barriers be used to sectionalize the mine as additional defense; but these should not be regarded as a substitute for generalized rock-dusting."" (Mine safety decision, No. 5, April 7, 1927.)The purposes of this circular are to present concisely the requirements for effective rock-dusting of coal mines in order to prevent propagation of mine explosions, and to point out the principal related facts on explosibility of coal dusts and mixed coal-mine dusts, as determined by extensive testing in the Experimental Mine of the Bureau of Mines. study of these principal facts on coal-dust explosibility in conjunction with the recommendations for rock-dusting, should help to make clear to mine operators and others concerned the necessity for systematic rock-dusting in all coal mines except anthracite mines, and the futility of inadequate or sporadic rock dusting.The descriptions of nearly 1000 explosion tests in the Experimental Mine are available in a forth-coming bulletin2 and in earlier publications.3For detailed specifications as to the kind of rock-dust, amount to use, where to be applied, and method of sampling and testing, the reader is referred to Bureau of Mines Serial 26064, and American Engineering Standard Committee ""Recommended American Practice for Rock-Dusting Coal Mines"" quoted in Bureau of Mines Information Circular No. 60305.Summary of Specifications for Rock-Dusting1. Mines to be rock-dustedAll coal mines, except anthracite mines, should be rock-dusted.2. Extent of rock-dustingAll open accessible parts of a coal mine should be rock-dusted, including slopes, entries, cross,-cuts, and rooms, headings and pillar workings to within at least 50 feet of the face.3 Amount of rock-dustingAfter cleaning up the coal dust as thoroughly as practicable, sufficient rock-dust should be used to have the mixture of remaining coal-dust plus the rock-dust in any zone contain 65 per cent or more of inert or noncombustible matter. First dusting may require 3 pounds to 5 pounds per linear foot of passageway.4. When to rock-dust In any zone or section (made by dividing the mine for rock-dusting purposes) when the incombustible content falls to 55 per cent, that section should be re-rock-dusted so as to bring the incombustible content well above 65 per cent."

Jun 1, 1927

By Guy A. Johnson

Despite the use of warning alarms to alert miners to the backward movement of large mining equipment, miners still are injured too frequently in backup accidents. Currently approved backup alarm technology consists of continuous sounding alarm systems. New technology has developed a warning system that initiates an alarm only if there is an object close behind the vehicle. This advancement eliminates constant exposure to the alarm because a warning is given only in case of a potential collision. Adoption of this development can improve safety and reduce damage, especially for front-end loaders (FEL's). It will also eliminate a source of nuisance noise in urban and residential areas. This Bureau of Mines report describes the general characteristics of infrared (IR) light, ultrasonic wave, and Doppler radar technology as used for backup alarms, and reviews the testing of the most promising detection devices.

Jan 1, 1986

By Eric E. Cather

A mineral survey of a portion of the Lake Eleanor RARE II area (No. 5807), Trinity County, California, was done by the U.S. Bureau of Mines and U.S. Geological Survey (USGS). Approximately 8,650 acres (3,500 ha) of the Lake Eleanor RARE II area not examined for this report had been previously investigated by U.S. Bureau of Mines and U.S. Geological Survey personnel and published as part of USGS Bulletin 1371-B, (Hotz, 1972) Mineral Resources of the Salmon-Trinity Alps Primitive Area, California. The report showed that the section included in the rake Eleanor RARE II area contained no metallic mineral resources. Geochemical sampling indicated that the Lake Eleanor RARE II area contains no potentially important mineral resources. About 4,650 acres (1,880 ha) of the eastern part of Lake Eleanor RARE II area were examined for this report. The Bureau of Mines was responsible for detailed examination and sampling of mines, prospects, and mineralized zones; the Geological Survey conducted geological, geochemical, and geophysical studies of the area. This area is underlain mainly by granitic rock and serpentinite.

Jan 1, 1981

By A. Renton Amell

The rate of dissolution of U02 was measured in acid solutions similar to those used for in situ leaching, with S04 of 10-1.82 to 10-4 M, Fe(III) of 10-2 to 10-4 M and pH's of 1.1 to 2.3. The dependence of dissolution rate on pH was small and inconsistent, probably reflecting the combined effects of a very weakly polar oxidizing complex, probably FeSO4+, and a nearly neutral U02 surface. Differences in the state of the U02 surface may explain this variability as well as contrasts between these results and results reported in other work. Changing either S04 or Fe(III) concentrations significantly affects dissolution rates. Increasing low sulfate concentrations in solutions containing 10 2 M Fe(III) at pH 2 results in formation of FeSO4+. In such solutions, rates increased with (S04)/(Fe(III)) up to 1:30, thereby indicating that the oxidation of U02 by FeSO4 is more rapid than by Fe3+. However, the dissolution rate decreased at higher (SO4)/ (Fe(III)), due either to sorption of SO42- on the UO2 surface or to formation of other less reactive sulfate complexes such as Fe(S04)2 or FeHSO4+ However, Fe(III) concentration is the dominant factor in determining solution rates. The rate was directly proportional to ferric iron concentration, indicating that the rate-determining step of the dissolution reaction is a single-electron oxidation by a ferric complex. Dissolution rates were lower in solutions of 0.1 and 1.0% H202 (0.029 and 0.29 M) than at similar concentrations of ferric iron because of formation of an insoluble surface coating of uranium peroxide, UO4?4H20. This phase may limit the value of hydrogen peroxide as an oxidant in lixiviants, not only by its very low solubility, but perhaps also by filling pores and reducing permeability in the ore body.

Jan 1, 1978

By [F. P. ] Stambaugh

Results of research on the hydrothermal precipitation of zirconium oxide from the Bureau of Mines' zirconyl chloride-sulfate strip liquors indicate that nuclear grade material can be prepared by this process. Greater than 99% of the zirconium value can be precipitated at 250-260°C in short (5-10 minutes) reaction time without consumption of acid value of the liquor. Thus, precipitation of zirconium dioxide on a continuous basis, i.e., the zirconium dioxide is precipitated in a continuous mode of operation by pumping the strip liquor through a heated pressurized reactor and recycle of the acidic (spent) liquor to the process stage are favored. The results of accompanying studies of liquod/solid separation, product washing and dewatering, product purity, and chlorination of the product are presented and discussed.

Jan 1, 1980

By Robert M. Koerner

The feasibility of using small-scale models to simulate residential masonry foundation walls subject to fatigue loading was investigated. Five wall segments were modeled in one-quarter scale using dynamic similitude equations. The walls were dynamically loaded using a sinusoidal base motion and wall accelerations were monitored. The stiffness, natural frequency response, and damping characteristics were measured. The number of cycles of testing necessary to cause initial visible cracking was recorded. Analysis of the data indicated the importance of the relationship between the forcing function and the natural frequencies of the structure in influencing cracking damage.

Jan 1, 1980

By Ann G. Kim

The Bureau of Mines estimated the methane content of a coal, which depends primarily upon rank and pressure, from the adsorption equation V kpn, where k and n are constants related to rank. By incorporating corrections for moisture, ash, and temperature, and estimating pressure and temperature as a function of depth, the methane content of coal in place can be estimated from the following equation: [ ] Values calculated with this equation generally are in reasonable agreement with direct determinations. By assuming a standard moisture and ash content, and using the hydrostatic head to estimate pressure, a graph of rank and depth versus gas content was constructed. Although estimated values were consistently high for several high-volatile bituminous coals from an area where the pressure is known to be less than hydrostatic, the estimated methane content for most coals shows reasonable agreement with values determined by the direct method.

Jan 1, 1977

By Mackenzie Burnett

This program was initiated by USBM to quantify the respirable dust problem caused by the use .of roadheaders in underground metal/nonmetal mines with special emphasis on this problem in uranium mines. The contract called for the development of methods or equipment to alleviate the respirable dust and to implement the solution in a mine. Attempts to quantify the dust problem were made in the following way: survey of MSHA records, survey of state mine enforcement agencies, survey of mine records, dust measurements taken at two mines using roadheaders. The results of this study are not conclusive due to very limited and sometimes less than useful data; however, the study does indicate that a serious dust problem could and may exist. If and when roadheader use becomes more popular, it is almost certain that development of dust control procedures and equipment will be necessary. This contract was concluded without developing this equipment since only one roadheader is currently in use in an American uranium mine and the mine prefers not to participate in the program at this time. This report discusses the available data concerning respirable dust problems and presents a solution which can potentially help to solve the problem. The solution requires the use of blowing ventilation, on-board dust extraction at the source, and filtration, as well as continued use of water sprays. The on-site tuning of such a system is necessary to demonstrate the degree of improvement possible.

Jan 1, 1981

By Stephen C. Tadolini, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990’s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine’s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

Although the mining industry has achieved record-low fatalities and injuries for each of the last three years, there are still too many miners injured or killed in this nation ís mining operations. Many mining injuries or deaths might have been prevented by using risk assessment to identify and control or eliminate the hazards associated with a task. To focus attention on the importance of conducting risk assessments in keeping mining workplaces safe and healthful, MSHA introduced this initiative on October 12, 2004. This initiative is called SLAM. SLAM is an acronym for Stop, Look, Analyze, and Manage. The steps involved in SLAM are: Stop ñ stop and consider the work involved Look ñ look for and identify the hazards Analyze ñ analyze what needs to be done Manage ñ manage safety by developing and implementing controls Everyone should be aware of the risks of an accident before beginning a task. It may not always be obvious that performing a seemingly routine task could result in an accident. That is why conducting a risk assessment is so important. Itís important to remember that over time a mining workplace seldom remains unchanged. Risks must be assessed whenever procedures or processes change, whenever new tasks are started, or non-routine tasks are performed.

Jan 1, 2005

By A. T. Coumbe

The first national survey covering sales of fuel oil by States and principal uses was made in 1926 by E. B. Swanson of the Bureau of Mines (then under the U. S. Department of Commerce) under a cooperative agreement with the American Petroleum Institute. This annual study, covering the market for fuel oil, was made through 1930 with the financial help of the institute bat has since been continued by the Bureau up to the present time. The scope and coverage of the survey have gradually changed over the years as new uses for fuel oil have been found and new products have come into importance resulting in market expansion. Range oil (No. 1 fuel oil or kerosine) came into use for cooking and space-heating daring the depression era in New England, and it was first reported as a total in the 1931 survey. In 1934 the sales were compiled on a State basis. State totals for distillate fuel oil, Diesel fuel, and residual fuel-oil sales were first shown for 1934 and by principal uses and States in 1937. Kerosine deliveries by States and main uses were also released for the first time in 1937.

Jan 1, 1952

By R. F. Kehrman

Voice Frequency (VF) electromagnetic trapped miner location devices were tested for reliability and effectiveness in 93 coal mines. Tests included uplink pulsed CW, downlink pulsed OW and downlink voice evaluations. Frequencies were 630, 1050, 1950 and 3030 Hertz. Overburden depths varied from 70 feet to 1550 feet. Successful communications were established at 91 of the 93 mines. Data indicate the transmitters and receivers will operate in practically all coal mine environments. Reliability and accuracy as location devices appear to depend on noise, depth and presence of metallic objects which distort the magnetic field. In addition, theoretical models appear to define best case situations in terms of noise and conductivity. Minor hardware problems were encountered, mostly involving battery contacts, switches and antenna cables on the receivers. No hardware problems occurred with the transmitters.

Jan 1, 1978

By R. A. Franks, G. F. Friel, J. C. Edwards, L. Yuan

Five mine fire experiments were conducted in a 2.08m high and 2.90m wide, ventilated mine entry in the National Institute for Occupational Safety and Health (NIOSH)'s Safety Research Coal Mine (SRCM) to determine the effect of the dispersion of carbon monoxide (CO) on mine fire detection. CO measurements were made at distances from 7.6 m to 45.2 m downwind from the fire with diffusion mode CO sensors positioned near the roof. For small intensity fires, less than 30 kW heat release rate, generated by 14 kg coal in a 0.61 m square tray, it was determined that air flow and sensor spacing were significant for fire detection at the 10 ppm CO alarm level. Within 15.0 m downwind distance from the fire, 10 ppm CO alarm values occurred for volumetric air flows less than 11.5 m3/s. However, the 10 ppm CO alarm value did not occur 30.0 m downwind from the fire for air quantities greater than 6.2 m3/s due to dilutive mixing of the CO in the air stream. The criterion that the mine fire alarms occur within 15 min of the onset of flaming combustion could not be consistently met with the 10 ppm CO alarm. This suggests the use of lower CO alarm values, or reduced CO sensor spacings for mine fire protection. It is demonstrated how computational fluid dynamics (CFD) can be used to model the CO dispersion downwind from the fire in support of a plan to optimize sensor spacings.

By William H. Schiffbauer, Timothy Lutz, Michael R. Yenchek

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL) participated in an experiment to facilitate the remote control of dozers used on coal stockpiles. The experiment consisted of supplementing the normal sensory cues an operator requires to manipulate the dozer from a remote location. NIOSH provided and tested a vision systems intended to give the operator the ability to operate the dozer safely and efficiently from a remote position. This paper highlights the genesis of the experiment, identifies the contributions of Consol Energy and Caterpillar, and details the NIOSH efforts and successful test results. Keywords-remote-control; vision system; stockpiles; safety

By William C. Cooley

[Data from t.-raturs on each hydr,ne has been assembled on the- data sheets whichw6ed in this Appandin. Dai_iis are provl_ od for ::amines or hydraulic s-ctions in the USSR (TDPhw~s), 8 in ASR (Kuzbass) , 1i-gin i, 1 in 7in China, i in Japan, and l in C~n- i.Ata sheetsiov tion prepared for mines in New Zealah_~sddered very rele¬ vant, nor forf !aA of information. In aW,!~.F in : --- C=SR for tiara ShoeLS ara 1palAwdl satinieral mines have operac- ~ - re Manned about which very limited data exist as folloos:]

Jan 1, 1975