Search Documents

By William J. Campbell

Evaluation by the Bureau of Mines of published expansion values for magnesium oxide shows significant variation in values, which may be attributed to sample variables, experimental errors, or systematic differences between measuring techniques. To eliminate the sample variable in measuring expansion, thermal expansion characteristics of a high-purity polycrystalline magnesium oxide were determined by 21 cooperating laboratories using one or more of the following techniques; X-ray camera, X-ray diffractometer, dilatometer, interferometer, and telemicroscope. All expansion values were corrected by the author to a single reference temperature of 25° C. Linear expansion was expressed as a power series in the form of the following equation. Expansion (percent) = [[ A + B (?t) + C (?t)2] ?t 104] The constants, A, B, and C, were determined by least square techniques for X-ray camera, X-ray diffractometer, and dilatometer data separately, and for combined data of all five techniques. Expansion values are tabulated from 26° C. to 1,400° C. in 2° C. intervals using constants derived from X-ray camera data. Below approximately 500° C., expansion values obtained by dilatometric and interferometric methods are significantly lower than those by X-ray methods; above 500° C., this bias decreases rapidly. Comparison of results within methods showed the least variance for X-ray camera results; dilatometer and X-ray diffractometer results have about the same variance. The average deviations, in percent, between observed and calculated expansion values among methods were approximately 10 percent from 100°C. to 300°C., 5 percent from 300°C. to 500°C., and 2 percent from 500°C. to 1,400°C. Maximum deviations were approximately twice as large in most instances.

Jan 1, 1962

By K. K. Kershner

The purpose of this investigation was to develop methods, on a laboratory scale, for recovering tin from Bolivian metallurgical slimes. Petrographic and chemical analyses were made of slime ore fractions from several well-known tin operations. High percentages of the total tin were volatilized as chlorides at temperatures below 600° C. Under optimum conditions reaction rates were relatively rapid, and the chloridizing reaction approached completion. Owing to the low temperatures involved and the high yields of tin, the process was considered to have possibilities for treating Bolivian slimes on a commercial basis. ACKNOWLEDGMENTS Appreciation is hereby extended to the Patino Mines and Enterprises, Inc., of Bolivia, for supplying slimed tin ores that were used in the experimental work. This company has since been nationalized.

Jan 1, 1959

By Donald W. Mitchell

Research shows that water neutralizes the explosion hazard of coal dust when present in sufficient quantity and when intimately mixed with the dust. The quantity of water required to neutralize coal dust and coal-rock dust mixtures is about equal to the limiting moisture adsorptive capacity of the dust; the adsorptive capacity increases with increase in the fineness and volatile content of the coal. Pools of water or high atmospheric humidity do not reduce the explosion hazard. Although wetted dust is less dispersible than dry dust, poor dispersibility cannot be relied on as the sole safeguard against explosion. Dust mixtures that contain water in excess of their limiting adsorptive capacity are dispersed and ignited by severe initiation sources. Pure coal dust adsorbs water with difficulty and retains water poorly; adsorption and retention is increased by the addition of rock dust the coal; the rock dust agglutinates wetted coal and assures that incombustible is present should drying occur. Therefore, it is advantageous to rock-dust wet areas in bituminous coal and lignite mines. When coal-rock dust mixtures are wetted and subsequently dried, the explosion hazard is about the same as for dust which was not wetted.

Jan 1, 1962

By R. P. Vinson, Abdurrahman Cetinbas, Joseph Cervik, M. G. Zabetakis

The effect of water infusion on the flow of methane and on the production of dust was investigated at an active face in the Pittsburgh coalbed. The average total flow of methane at the face decreased by approximately 79 percent, whereas the flow from the ribs increased about 24 percent after infusion. On the day after infusion, dust concentrations appear to have been reduced; however, the presence of large quantities of rock dust obscured the results on the following days.

Jan 1, 1972

By W. W. Adams

Rock dust, as a preventive or limiting factor in explosions of gas and coal dust in bituminous-coal mines, was used in larger quantities in 1939 than in any other year except 1937 since annual figures first became available in 1930, Reports from mining companies to the Bureau of Mines revealed that 144,430,000 pounds of rock dust was applied to underground nine workings in mines that produced 126,635,677 short tons of coal during the year. This quantity of rock dust applied averaged 1.14 pounds for each ton of coal produced. Rock dusted mines were the source of 39.7 percent of the total production of bituminous coal from underground mines; 33.2 percent of the total number of underground workers were employed at rock-dusted mines, and 35.8 percent of the total number of man-hours worked underground at all bituminous-coal mines in the United States during 19719 can be accredited to mines so treated. Rock dust was employed chiefly in the larger mines, which numbered only 431 out of 6,016 underground mines in operation in 1935, according to reports from mining companies. The mines in which rock dust was used had an average of 288 underground employees per mine, whereas mines in which rock dust was not used averaged only 62 underground employees per mine.

Jan 1, 1940

By W. W. Adams

Rock dust, as a preventive or limiting factor in explosions of gas and coal dust in bituminous-coal mines, was used in larger quantities in 1939 than in any other year except 1937 since annual figures first became available in 1930, Reports from mining companies to the Bureau of Mines revealed that 144,430,000 pounds of rock dust was applied to underground mine workings in mines that produced 126,635,677 short tons of coal during the year. This quantity of rock dust applied averaged 1.14 pounds for each ton of coal produced. Rock dusted mines were the source of 39.7 percent of the total production of bituminous coal from underground mines; 33.2 percent of the total number of underground workers were employed at rock-dusted mines, and 35.9 percent of the total number of man-hours worked underground at all bituminous-coal mines in the United States during 19719 can be accredited to mines so treated.

Jan 1, 1940

By Roger M. Turpening

This study was performed to examine the feasibility of using seismic shear waves to detect the presence of abandoned coal mines. !he Antiquity Coal Mine near Antiquity, Ohio was used as a region of known voids. No attempt was made here to accurately locate the mine tunnels if detection was obtained. The results of this study were positive. Sharp changes in the amplitude of the received shear waves were clear indications of the presence of a fluid (gas or liquid) filled region between the source and receivers. When moving the source showed no change in the received signals it was concluded that the voids existed beneath the sensors. Prior to these tests drilling (SM-3) had determined that a void did exist in this area. This void was confirmed by this shear wave test and two additional voids were found.

Jan 1, 2012

By J. A. Markovits

Coal has been hydrogenated in Germany on a lather extensive scale for the past 20 years, but the process is new to the United States. Although pressures up to 15,000 pounds per square inch have been employed on commercial scale in the synthesis of anhydrous ammonia, and there is evidence that valves, tubing, and equipment have been developed recently up to 30,000 p.s.i. working pressure at moderately elevated temperatures for limited industrial production of plastics, such pressure ranges are unusual in American industry, and equipment designed for them is not commonly available. In the Coal Hydrogenation Demonstration Plant at Louisiana, Mo., 10,000 p.s.i. operating pressures are combined with temperatures up to 1,000° F., and the materials to be processed under these conditions range from gases to mixtures of viscous liquids containing high percentages of abrasive solid particles. These service conditions presented unusual engineering problems requiring thorough investigation, Limited financial resources arid rigid time schedules inherent in the synthetic liquid fuels act often forced decisions before the best answer to a problem could be developed. Sometimes the ideal technical solution proved to be beyond the financial limitations of the demonstration-plant program.

Jan 1, 1949

By R. Hogg, S. Chander

"INTRODUCTION The behavior of particulate systems in general is determined by the properties of the solid and fluid phases and of the interfaces between them. As particle size is reduced, the inter facial effects become increasingly important until, in colloidal systems, they become completely dominant. Interfacial phenomena are especially important in coal processing for a variety of reasons. Because coal is naturally hydrophobic and its density is low, surface forces begin to dominate over gravity at relatively coarse sizes. Coal is thermodynamically unstable in the presence of air, so that surface oxidation occurs readily leading to important variations in surface properties with time and environment. These effects are further compounded by the inherent heterogeneity of the material.Surface characteristics and properties play a significant role in most aspects of coal processing. Comminution, for example, is a process of creating new surface, while agglomeration involves the reduction of surface area and is usually controlled by surface forces. Both solid-solid and solid-liquid separations are influenced by interracial phenomena, Gravity separations are usually performed in a liquid phase and are affected by the wetting characteristics of the various solids present and by the need to ensure proper dispersion of the individual particles. Froth notation, of course, separates particles on the basis of differences in surface characteristics. Chemical processes such as leaching generally involve interfacial reactions whose rates depend on surface area and may be influenced by electrochemical effects in the electrical double layer at the solid-liquid interface, or by adsorption of reactant and/or product species from solution. Solid-liquid separations and associated processes such as flocculation are strongly dependent on the nature and properties of the solid-liquid interface.In characterizing solid surfaces, it is important to consider first the surface area, since this determines the relative importance of the interfacial effects. The structure and chemical composition of the surface may depend on the distribution of different petrographic constituents and impurities such as finely disseminated mineral matter, on the extent of surface oxidation, and on adsorption from the environment. These, in turn, will generally determine the surface properties which define particle behavior. Since the relationships between structure etc. , and properties are not generally known, it is usually necessary to measure properties such as wettability and electrical charge directly."

Jan 1, 1989

The Waukon iron deposit comprises about 210 acres situated 2-1/2 miles north of Waukon, in Allamakee County, northeastern Iowa. The deposits have been exploited intermittently since 1899 and have produced about 67,000 tons of concentrated iron ore. From January to May 1943, the Bureau of Mines investigated the deposit to determine the extent of the ore-bearing material and its amenability to concentration, Seventy-one test pits were sunk. Those that indicated are of a grade high enough to warrant concentration tests were sampled. Average grade of ore was indicated to be 37.02 percent iron and 27.78 percent silica on a dry basis. Beneficiation tests indicated that the percentage of recovery might be relatively low.

Jan 1, 1949

By Donald O. Capstick

[ ]

Jan 1, 1983

By S. J. Rodgers

This report presents the results of in-mine studies to determine the severity of dust sources in conventional mining operations. Three underground coal mines were surveyed using gravimetric samplers and GCA RAM-1 continuous dust monitors. Two additional mines were surveyed using only GCA RAM-1 monitors. Data on dust control methods were acquired during the survey, also. The results indicated that cutting/drilling and loading out were the dustiest operations during a conventional mining cycle. Roof bolting, shot firing and product transport were less severe dust sources.

Jan 1, 1983

By J. R. Thoenen

This circular is the second of a series presenting methods employed in solving the technical problems encountered in the production of sand and gravel. The first paper3 discussed the methods use in prospecting and exploration. This one teals with the problems involved in bringing a raw prospect to the production stage and considers the various methods of development and the Factors affecting that development. Later publications are planned to present and discuss methods of recovery and treatment. The recovery of sand and ravel from natural deposits and their preparation for market involve a progressive sequence of operating steps or processes. Each step or process presents its own peculiar problems which require different angles of mental approach, methods, and tools, but all are more or less dependent on the step or process which precedes or follows.

Jan 1, 1933

By Duane L. Abata

This work, conducted under Bureau of Mines contract, deals with the development of a computer graphics software package that will: 1. display mine ventilation schematics and other representative Illustrations for a real-time data acquisition system under development by the Bureau, and, 2. utilize the Bureau-owned Minefire and Ventilation Code for display of ventilation on and contamination predictions. The software package has been written try operate on a 64K, Z-80 based microprocessor-computer. The project has been divided into two phases. The first phase dealt with the development of the graphics software The sec rind phase dealt with the retrofit of the Minefire and Ventilation Code to the Z-80 microprocessor-computer.

Jan 1, 1984

By Eric E. Cather

A mineral survey of the Fisher Gulch RARE II area (A5299), Trinity County, California was conducted by the U.S. Bureau of Mines and U.S. Geological Survey. The Bureau of Mines was responsible for detailed examination of mines, prospects, and mineralized zones; the Geological Survey conducted geological, geochemical, and geophysical studies of the area. The area is underlain by the Salmon Hornblende Schist. Tonalite stocks 1.5 mi (2.8 km) to the east and northeast of the area intrude the schist and are closely associated with the nearby nines (Cox, 1967). The mines have quartz veins containing sulfides and gold in shears trending east to north past in the schist and tonalite (Hotz, 1972). Strewn and terrace gravel s occupy most of the drainages, many have yielded substantial quantities of gold.

Jan 1, 1981

The Leuna Factory of the I. G. Farbenindustrie A. G., situated near Merseburg, is the biggest heavy-chemical plant in Germany and produces a very wide range of products, mainly based on hydrogen or hydrogen and carbon monoxide. Its principal products are ammonia, synthetic petrol derived from the hydrogenation of brown coal, and synthetic alcohols made from hydrogen and carbon monoxide. The plant was first, visited on April 21, 1945, by a team including E. Cotton, V. Haensel, E. B. Peck, P. K. Kuhne, H. M. Weir, L. L. Hirst, W. W. Odell, G. U. Hopton, H. Hollings, J. F. Ellis, and H. G. Simpson. It was again visited on May 8-24, 1945, by a combined British and American team consisting of R, Holroyd, M. A. G, Banks, D. A. Howes, A. J. V. Underwood, R. A. Taylor, W. F. Faragher, H. Schindler, and J. G. Allen. This team was later joined by J. F. Ellis and R. J. Morley. A third visit with particular reference to catalyst manufacture was made by W. F. Faragher and W. A. Horne, and the notes of these latest investigators have been taken into account in preparing the report. This report was edited by Dr. R. Holroyd.

Jan 1, 1946

By Dean H. Ambrose

This paper presents the results of a study using computer human modeling to examine machine appendage speed. The objective was to determine the impact of roof bolter machine appendage speed on the likelihood of the operator coming in contact with. A contact means two or more objects intersecting or touching each other, e.g., appendage makes contact with the operator?s hand, arm, head or leg. Incident investigation reports do not usually contain enough information to aid in studying this problem and laboratory experiments with human subjects are also not feasible because of safety and ethical issues. As an alternative, researchers developed a computer model approach as the primary means to gather data. By simulating an operator?s random behavior and machine?s appendage velocity, researchers can study potential hazards of tasks where it is not possible to perform experiments with human subjects. Analysis information is helpful to the mining industry in terms of making recommendations that reduce the likelihood that roof-bolter operators experience injury due to contact with a moving boom. Data analysis of roof bolter simulations show that the virtual-operator?s response time has little effect on the number of contacts experienced. Based on frequency and cross-tabulation, regardless of other variables, contact incidents were always greater when the boom was moving up, were always greater on the palm, and were always greater for the boom part of the machine. Also, regardless of boom speed, the 25th-percentile-sized operators experienced more contacts than did other operator sizes. Furthermore, regardless of boom speed, the 152-cm mine seam experienced more contacts than did other seam heights tested. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speed greater than 41 cm/s results in a substantial increase in risk to the roof bolter operator and should probably be avoided. At speeds less than or equal to 25 cm/s are associated with a more modest relative risk, which represents an acceptable level of risk. Also, at speeds between 25 and 41 cm/s, there could be a particular boom speed in this range at which a significant inflection point in the relative risk estimates occurs. Based on the results, this issue needs to be addressed by future research.

Jan 1, 2003

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitlted "Evaluation of Proximity Warning Devices II dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electro-static fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factory of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By H. E. Heide

"Before the war, the United States was the world’s leading consumer of tin, the industrial applications of which had become widespread. Domestic production was negligible, and requirements were met almost entirely by imports, principally from British Malaya, United Kingdom and China. Average annual imports for the years 1925-1929 amounted to 78,009 long tons.With the advent of war in Europe and signing of the Japanese-German pact, it was realized that foreign sources of supplies were threatened, and steps were taken by Congress to forestall critical shortages of tin and other minerals. These steps in regard to tin included stock-piling, improving reclamation and conservation, increasing South American production, constructing a smelter in the United States for treatment of tin, ores, and intensifying the search for domestic tin deposits. Annual imports were raised to 140,873 long tons by 1941. On 1945, annual imports had shrunk to 37,675 long tons and consumption had been reduced to 52,100 tons of primary and secondary tin but not tin content of scrap alloy.The Strategic Minerals Act, passed by the Congress in 1939, authorized the investigation of domestic tin deposits.As Alaska had supplied virtually all of the domestic output of tin, an investigation of Alaska deposits was undertaken in 1940 and 1941 by J. B. Mertie, Jr., and Robert R. Coats of the Geological Survey.The Lost River lode tin mine on the Seward Peninsula was examined by H. E. Heide of the Bureau of Mines in 1942. Possibilities for developing a significant amount of tin appeared favorable, and exploration of the ore bodies was started in August 1942."

Jul 1, 1946

By Harold J. Bennett

The purpose of this study was to develop methods for the financial evaluation of mineral deposits. This includes the selection of the best alternative mining and processing methods and production rates. This was done by performing a financial evaluation through computer simulation using sensitivity and probabilistic risk analysis. The criterion used to measure the relative advantages of these investment and operating alternatives is the discounted-cash-flow rate of return. Included is a description of the theory and methods used in the probabilistic analysis approach, which is based on the premise that the expression of a range of values in establishing an estimate for a parameter is more realistic than the choice of a single value. Numerous simulations are made using randomly selected values of the input parameters resulting in a frequency distribution of the rates of return and their relative probability of occurrence. The sensitivity analysis method is described and combined with the probabilistic analysis to interrelate mineral reserves, capital investments, operating costs, and production rates. The ability to vary these input parameters on successive runs has permitted the selection of the best alternative mining and processing methods and production rates for a given mineral deposit. For illustrative purposes the evaluation of a mineral deposit was performed using three alternative mining and processing methods at three different quantities of resources and various production rates and prices. The computer program used in this analysis was written in FORTRAN II for maximum compatability and should run without modification on most computers having BK (8,000-word) core memory, a card reader, and printer (120 characters per line).

Jan 1, 1970