Search Documents

Reduce the potential for injuries in underground mines by providing an alternative to manually lifting and holding heavy roof-support beams. The Problem I-beams, rail sections, and wooden cross-beams are often used in mine haulageways where extensive roof support is needed. Studies by the Bureau of Mines have shown that many mines must resort to manually lifting, moving and installing these beams. Such manual-handling activities have the potential for causing injury to mine workers, particularly back injuries. I-beams used for roof support can typically weigh from 400-500 lbs. Rail sections weigh about the same as the I-beams. Wooden beams can weigh from 200 to 300 lbs. To lift a single beam usually requires the efforts of 3 to 5 mine personnel.

Jan 1, 1988

By Irving Hartmann

Falls of roof in coal mines and means of preventing them have been subjects of study for many years, and an extensive literature has resulted. Usually each individual paper has placed emphasis on one phase of the subject, such as fatalities, nature and extent of nonfatal injuries, methods of tembering (particularly in rooms or other wide places), safety along retreating rib lines, and methods of causing falls in abandoned areas. It is only in recent years that there has been persistent question as to why

Jan 1, 1941

By L. M. Irwin

This Bureau of Mines investigation relates the physical properties of copper reverberatory furnace slags to changes in composition, The smelting of upper Michigan copper ore presents some problems that probably differ from those of other copper smelting areas. The study of these problems has, however, provided important data regarding slags in general and therefore will be of value to other operations as well. Conclusions reached from this study were: (1) Slag fluidity and refractive indices varied directly with the iron content and inversely with silica, lime, and alumina, and (2) there was no apparent correlation between slag fluidity and its copper content.

Jan 1, 1962

By John P. Shubilla1, Nicholas Kyriazi

A joint effort by the Pittsburgh Research Center (PRC) and the Mine Safety and Health Administration (MSHA)3was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fifth phase of testing from mid-1993to early 1996. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS) at PRC. These results indicate that most of the apparatus, if they pass their inspection criteria, perform satisfactorily.

Jan 4, 1996

This report presents the results of a study of Kennecott Copper Corporation?s Chino leaching dump at Santa Rita, N. Mex. The stability studies described herein were performed on only one cross section of the leach dump, utilizing data obtained from drilling, sampling, and testing, which was limited in nature. The first part of the report contains a discussion of site geology and seismicity, pertinent information on the waste material disposal system and leaching method, a discussion of the waste embankment characteristics, a summary of the engineering analyses, and a bibliography. The second part (appendices) contains basic geologic and engineering data supporting the discussions in the first part.

Jan 1, 1974

By Arthur M. Hartstein

The Federal Bureau of Mines, under a contract with Ultrasystems, Inc., investigated the thermal oxidative degradation characteristics of conveyor belts used in underground mines. This included the determination of smoke evolution, glow characteristics, char yields, and the identification and quantification of all volatile decomposition products in the form of gram of specific product formed per gram of belt sample tested. In addition to these investigations, degradation studies were conducted on some pure ingredients used in conveyor-belt formulations. Three basic classes of belts were investigated: neoprene, polyvinyl chloride, and styrene-butadiene rubber compositions. The studies indicate that styrene-butadiene-based belts exhibit good flame resistance and are the least hazardous in regard to overall formation of toxic decomposition products. Under this program, thermogravimetric analysis was definitely established as a method of material differentiation.

Jan 1, 1976

By Sidney Katell

This report, covering the period January 1968 through December 1968, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the tenth in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost of engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Lines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress s 6. Chemical Week. 7. Coal Age. 8. Coal Mining and Processing. 9. Cost Engineering. 10. European Chemical News. 3 11. Hydrocarbon Processing. 12. Industrial and Engineering Chemistry 13. Oil and Gas Journal. 14. Petroleum Engineer. 15. World Oil.

Jan 1, 1969

An active list of permissible explosives was published in July, 1931, as part of United States Bureau of Mines Report of Investigations 313, under the title of "Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1931." Changes in that list were authorized in August, September, October, November, and December, 1931, and. January and March, 1932, as published in Reports of Investigations 3l40, 3147, 3l50, 3155, 3158, 3161, and 3163, respectively. By these changes the following explosives were added to the active permissible list: [Austin Red Diamond No. 1, L. F. Gel-Coalite W. L. F. Austin Red-Diamond No. 5, L., F. Gen-Gel No. 2. Black Diamond Nu-Gel No. 1 Genite C-1 Burton 1, L. F. Liberty No. 4 Burton 2, L. F. Liberty No. 5 Burton 10, L. F. Peerless D Burton 12, L. F. Permigel 1, L. F. Burton F, L. F.]

Jan 1, 1932

A pilot program was undertaken to evaluate a process developed by the U.S. Bureau of Mines to recover nickel, cobalt, copper and chromite from domestic nickel laterite resources. An existing five ton per day pilot plant was modified to accommodate treatment of laterite by the Bureau process, which employs reductive roasting, ammoniacal sulfate leaching, solvent extraction, and electrowinning to extract, separate, and recover nickel, cobalt and copper as high purity cathode products. Three distinct types of laterite i.e., limonite, saprolite and a mixture of limonite/saprolite were processed through the plant during three operating campaigns. Nickel cathode was made during all three campaigns, while cobalt cathode and chromite concentrate were recovered only during processing of limonite. Leach extraction of nickel and cobalt averaged 83 and 67 percent, respectively, while the overall recovery was 80 and 63 percent for nickel and cobalt, respectively. Initially, over-reduction of iron in the saprolitic calcine contributed to poor settling of the leached solids. This problem was overcome by careful control of reducing conditions and flocculant addition. An economic feasibility study was made for a 5000 TPD grassroots laterite processing facility scaled-up from pilot plant data. Estimated (+ 30) percent capital cost for a Nine and plant is $367 million with an estimated $103 million per year operating cost. The study indicates that low-grade domestic laterite may he processed with marginal profit- ability.

Jan 1, 1982

By Wallace W. Key

This report concerns types, quantities, specifications, and uses of non-metallic minerals as a basis for improving their supply, conservation, and utilization. Supply-demand details concerning mineral fillers, rooting granules, and roofing rock used in asphalt are incorporated in this report, along with highlights on production and sales of rooting, floor tile, and other related asphalt products of California. Comparable data for the United States are included. Although large quantities of commercially prepared mineral fillers are used in asphalt for paving and related applications in other States, addition of commercial fillers for these uses rarely is required in California because of the natural tines available. On the other hand, California manufacturers of asphalt products other than having utilize about 300,000 tons of asbestos, diatomite, limestone, mica, soapstone, and other nonmetallic minerals as filler, mainly for reeling and flooring. Also about 500,000 tons of roofing, granules is produced in California, most of which goes into roofing manufacture in California. In addition. A significantly large and growing tonnage of relatively coarse mineral aggregates Ire used on low-angle, built-up, asphalt roofs to produce in attractive surface and offer protection against the clements. Clearly ill minerals used in asphalt products manufactured in California come from local sources, except asbestos and mica--and there are indications that local deposits of those commodities could be utilized in some use categories.

Jan 1, 1966

By D. L. Paulson

The Bureau of Mines is investigating pyrometallurgical and chemical methods for extracting copper from sulfide ores under conditions that provide for control of gaseous and solid emissions. Under this program, a new electrothermic reduction process was developed to produce blister copper after collecting essentially all of the sulfur by a single-unit operation. The process feasibility was indicated by a laboratory-scale investigation that demonstrated chalcopyrite concentrate can be roasted to less than 1 percent sulfur and that the resulting calcine can be reduced with carbon to blister copper by a cyclic process in a single arc-smelting furnace. Pilot-scale tests in an 800-kV-A electric-arc furnace demonstrated that 98.4 pct of the contained copper can be continuously recovered as metal by operating at bath temperatures between 1,350° and 1,375° C. Smelting rates of approximately 225 lb of blend ft2 of bath surface/hr resulted in power consumptions of approximately 520 kW-hr/ton of blend. The blister copper that was produced contained less than 0.1 pct iron while the precious metals reporting to the copper product and gangue material elimination were similar to those in a conventional smelting operation.

Jan 1, 1976

By Eugene H. Skinner

This Bureau of Mines report describes the fieldwork and subsequent analysis to determine physical properties, stress distribution, and several aspects of rock behavior as a necessary evaluation for a typical mine opening. All work was done at a test site on the 3300 level, Crescent mine, Coeur d'Alene mining district, Idaho. Free field stress beyond the influence of the opening was also determined. Conventional overcore technique with the three-component borehole deformation gage developed by the Bureau of Mines was used in three drill holes. Three field verification tests were performed using a gage newly developed by the Spokane Mining Research Center in an approach herein termed "initial deformation method." Use of this method validated that aspect of overcore theory which predicts that similar deformation effect occurs in the wall rock around the perimeter of an opening in rock under stress. Also described are all drilling procedures and performances. Physical property determinations were made on rock samples obtained from the three overcore drill holes. Twelve physical properties with a total of [532] values were obtained at various drill hole orientations and depths. Exhaustive statistical tests were utilized in the analysis of these physical properties. Further elaborated are statistical inferences based on these analyses. Extensive analysis and interpretation of Crescent mine geology are also described.

Jan 1, 1974

By J. R. Thoenen

Occurrences of titanium, zircon, and other heavy minerals are widespread in Florida. Deposits concentrated as "heavy sands" by wave and wind action have been mined an or near Atlantic coastal beaches since 1916. An important inland concentration at Trail Ridge; .believed, to have formed along an ancient share line, was disclosed by preliminary investigations (1947) by the Bureau of Mines. This report describes investigations to determine the extent and grade of "heavy-sand" concentrations in other inland stabilized dune areas in the central and northeastern parts of the peninsular region of the State (fig. 1). Portions of the central highlands south of Trail Ridge and terraces and dunes in the coastal lowlands region, east and northeast of the ridge were investigated. Holes were drilled in 10 areas (see table 1 and fig. 2) along State and County roads and on private property. They were spaced 250 to 2,000 feet. apart to obtain a cross-sectional picture of "heavy-sand" content in the dune areas. These sections were generally placed in east-west directions normal to the general trend Of the peninsula to intercept one or more of the ancient shore lines in the various areas (figs. 3 to 13, incl.). A total of 433 drive piped and 333 jet holes were drilled, and 7,293 bulk and core samples were taken. Intermediate holes were placed at closer intervals when field analysis indicated 1 percent or more of heavy minerals present. All of the holes drilled and the analysis of samples that contain 1 percent or more of heavy minerals are listed in table 2. Profiles (figs. 14 to 20, inclusive) show the more favorable concentrations, which are irregular in outline and erratic in mineral content. The highest concentrations averaged 1.0 to more than 2.0 percent heavy-mineral content, but a few individual hole samples exceeded 3.0 percent in grade.

Jan 1, 1949

By David D. Hottinger

Only a minimum amount of illumination is generally provided for many types of mobile surface mining equipment. This condition presents a hazard to operating personnel working on and around such equipment. To reduce this hazard MSHA has proposed safety regulations requiring minimum levels of illumination for hazardous zones on and in the immediate area surrounding surface mining equipment. This report describes a Bureau of Mines sponsored project demonstrating the feasibility and effectiveness of providing dragline illumination in compliance with the proposed MSHA regulations. A description of the computer aided design, on site installation and field evaluation of individual lighting systems for each of three different size draglines is presented

Jan 1, 1981

This Bureau of Mines publication contains the texts of the four papers presented at the May 6-7, 1980, seminar on the role of overburden analysis in surface mining. Coverage includes the geologic distribution of pyrite and calcareous material and its relationship to overburden sampling, overburden sampling and analysis, use of soil-overburden data in mine planning and development, and minesoil classification.

Jan 1, 1981

By M. John Brodie

This report reviews the regulatory environment as it pertains to tailings management and disposal from mining operations, excluding coal and placer gold operations, in the state of Alaska. It is based on the EPA's staff position on an effective program to regulate mining wastes as presented in the May, 1990 Strawman II document, The unique conditions which occur in parts of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a railings disposal facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection are examined.

Jan 1, 1992

By Gary A. Kingston

Rolled steel, steel forgings, and steel castings in the Pacific Northwest (Washington and Oregon) are produced principally in the Seattle, Wash., and Portland, Oreg., metropolitan areas. Steel-mill products are rolled from carbon and some alloy &eels by three companies into shapes such as reinforcing bar, rods, rounds, squares, flats, and hot-rolled strips; structural shapes, - such as angles, channels, and I-beams, also are rolled. Carbon and alloy steel ingots are poured and forged at a Seattle plant into ship shafting, drive shafts, billets, slabs, bars, rings, hooks, and other items. Static, shell, investment, and centrifugal castings are produced at 19 steel foundries in a wide range of steel specifications. All Pacific Northwest steel output is based on remelting steel scrap. Local iron ore might be used in the future to supplement steel scrap as a metal source. Ore reduction would probably be achieved by methods other than the blast furnace. Current melt-shop practice and problems are basically the same in Pacific Northwest steel plants as in cold-melt shops in other parts of the country. Quality steel production is receiving more emphasis in this region with the installation of modern analytical equipment and vacuum pouring and melting facilities.

Jan 1, 1962

By David C. Uhrin

Two improved methods have been developed to transfer microfilmed mine maps to suitable base maps showing surface features. The methods provide for (1) positioning and orienting maps; (2) merging adjacent maps; and (3) plotting maps at a common scale. One method produces an overlay mosaic of mine maps using an Integrated camera-processor. This photographic method shows the details of mine workings and is most useful for specific limited-area projects. In the second method, outlines of mine maps are digitized, manipulated, and plotted as overlays using a computer. This computer method can plot mine outlines and spatially index large numbers of microfilmed maps. Microfilmed mine maps used in this Bureau of Mines study are on file in the Mine Map Repository of the Eastern Field Operations Center. The base maps are U.S. Geological Survey 7.5-minute topographic maps. The demonstration area is located in the New Kensington East and West quadrangles, Pennsylvania.

Jan 1, 1977

By John F. Elliott

Six major trends that have had and are continuing to have major effects on the use and supplies of pig iron and scrap in the United States are (a) gradual replacement of the basic open hearth furnace (OH) by the basic oxygen furnace(BOF); (b) use of the electric furnaces for the production of plain-carbon steels, a trend which is closely related to the first; (c) United States changing from being a net exporter to a net importer of steel; (d) replacement of ingot casting by strand casting; (e) increased exportation of scrap; and (f) the lack of growth of the capacity of the U. S. steel industry to produce pig iron in the last 5 to 8 years. This report gives an analysis of the relationships between these trends and the use of processes for the production of raw steel in solidified form.

Jan 1, 1975

By William R. Barton

Sampling to determine development potential of beryllium deposits was conducted at 31 New England localities. A total of 54 additional areas where the geochemical environment appeared favorable were sampled to determine if economically interesting percentages of beryllia (BeO) might occur. Newry Hill-Plumbago Mountain, Maine, Iron Mountain, N.H., and Long Island, Maine, were investigated in some detail to determine the size and grade of deposits. The mineralized pegmatites at Newry Hill-Phunbago Mountain are extensive but very low grade; at Iron Mountain the ore bodies are very rich but of small volume; at Long Island beryl occurs with molybdenite, wolframite, and scheelite, but the tonnage of ore was not determined.

Jan 1, 1968