Search Documents

By Viktor Aranovich, Thomas E. Brown

The Almalyk Integrated Mining and Metallurgical Plant is located near Tashkant in Uzbekistan and is one of the former Soviet Union's largest copper producers. Almalyk consumes about 10,000 metric tonnes of explosives annually and expects this requirement to double by the end of the century as they implement a program to boost mine output.

Jan 1, 1998

By Lynn Long

We have seen many new developments in the explosive and blasting accessory category, but one of the most useful items is the blast control plug. Blast control plugs are cone shaped units that are placed in the stemming just above the explosive load. They are placed about 8 to 12 inches up into the stemming material.

Jan 1, 1996

By Jerry Wallace

Two recent-release boulders posed serious threats to public transportation and utilities in Washington State. Both required challenging drilling and blasting solutions.

Jan 1, 1997

By T Duff

This paper describes results from small scale tests conducted to determine the distribution of pressure on target plates when subjected to loading due to the detonation of a buried mine in various media. The tests are conducted by using saturated sand, dry sand, and water as the loading media. Different stand-off distances are investigated. Kolsky bars and pressure sensors are used to determine the free-field pressure - time profile of the output of the charge at any location on the vehicle bottom. For verification of the pressure results at certain distances, the specific impulse measured by utilizing different size round plates are employed. In order to investigate the loading mechanisms, high speed cameras are applied. The small-scale test results can be scaled to full scale by using verified scaling laws.

Jan 1, 2014

By Robert Hopler

Blasting powder is a slow-acting, black, granular explosive made of sulphur, charcoal and either potassium nitrate (saltpetre) or sodium nitrate. The blasting powder containing potassium nitrate is known as “A” blasting powder; that containing sodium nitrate, as “B” blasting powder. “A” blasting powder is a little denser, a little stronger and a little less hygroscopic than “B” blasting powder.

Jan 1, 2014

By John Manka

Emulsion explosives consist of an aqueous oxidizer phase, a fuel phase, and an emulsifier. The ability to use lower-cost sources for any of these raw materials presents an obvious economic advantage to emulsion manufacturers. This paper focuses on using low cost waste drain oils as the fuel phase in emulsion explosive applications. Laboratory studies showed that emulsions made from waste drain oils and agricultural ammonium nitrate prills were usable for emulsion explosives though their shear stability was weak. Customer field results proved that waste crankcase drain oil could replace half of the virgin diesel fuel in emulsion explosives to make an effective emulsion explosive product with a very low cost.

Jan 1, 2003

By S. Hosein, W. Birch, C. Johnson

The widespread adoption of electronic detonators has given rise to the development of linear superposition to control the environmental impact on both third-party properties and residents resulting from blast induced vibrations. Linear superposition has become a very effective tool in the hands of blasting engineers and has enabled aggregate reserves to be accessed that once had to be abandoned. This in turn has resulted in more and more complex blasting pattern to be developed that contain multiple rows and multiple decks all with different maximum instantaneous charge weights of explosives. This is then made more complex by having to consider multiple sensitive locations often with different Peak Particle Velocity vibration limits. This paper is a case study of what did happen when a blast was designed that “pushed the boundaries” of environmental blast vibration design and control, without taking fully into account the fundamental geophysical properties of seismic waves. The resulting blast design caused a greatly enhanced s-wave to be created in a critical direction from the blast pattern. The root cause being the s-waves from earlier detonating decks in the blast pattern arriving within 2 milliseconds of decks detonating later in the blast pattern. 209 individual decks were fired in the blast pattern of which 41 pairs of decks arrived at the observation location less than 2 milliseconds apart when taking into account the s-wave speed and direction. The lesson to be learned when using electronic detonators to limit ground vibrations from complex blasting patterns, is that it is just not good enough to look at the planned firing times, a professional blasting engineer must also understand the likely interaction of the various seismic wave types created and their combined impact on any given monitoring location.

Jan 1, 2024

By Norman Paley

A blasting project was undertaken at the Teck Alaska Red Dog Mine in 2005 to 2007 to determine the extent that using electronic detonators could increase Semi-Autogenous Grinding (SAG) mill throughput. The results of that project were reported at the 2010 ISEE Annual Conference. This paper is a postscript to that project and provides the fragmentation resulting from the implementation of a 15% pattern expansion using electronic detonators.

Jan 1, 2012

By Gustavo Huerta Valer, Jorge Cárdenas Miranda, Johan Salas Flores

One of the challenges of mining is the optimization of the blasting process, which has an important impact downstream in the processing of crushed ore in the plant, that is why mining companies ensure the results of granulometry obtained from the blasting process through a joint work with companies specialized in the process of loading with explosives.

Feb 6, 2023

By Raj K. Rajamani, Solomon A. Tucker, Michael K. McCarter

"In a study aimed at exploring possible improvements in operating performance at an Open Pit Copper (OPC) mine in the western U.S., the impact of blast energy changes on crushing performance was evaluated. OPC feeds its 3-stage crushing plant in 12-hour-day shifts with skarn ore from three domains: Pit_B (B), Pit_S Low-Grade (SLG) and Pit_S High-Grade (SHG), in the blending ratio 1:1:1 (B/SLG/SHG). Thecrushed product is fed to a 2-stage ball mill circuit. "

Jan 1, 2017

By Tom Snyder, John Brulia

Part I is the first of a series of articles by the authors on hazardous materials (HM) transportation safety and compliance for shippers and carriers who offer and transport commercial explosives in commerce on public highways in the U.S.

Jan 1, 2014

By Weiying Zeng, Shouwei Wang, Jinbei Zhong, Xiangdong Meng, Lingtian Meng

"Due to a drainage problem, the Lanzhou to Chongqing high-speed rail line had been out of service during the 2015 wet season, so a drainage tunnel is to be constructed for the line and required to be accomplished before the 2016 wet season. This drainage tunnel is only 5 meters below the line which is in service, therefore blasting vibration needs to be strictly controlled. This paper introduces all theapplied blasting methods, parameters and detonation throughout the entire project, finally bringing in the electronic detonator stagger phase technique and corresponding time difference for detonation."

Jan 1, 2017

By John Tatom, Michelle Crull, Robert Conway

The US Department of Defense Explosives Safety Board is sponsoring the development of a risk-based explosives safety siting program, SAFER. The fragment and debris hazard generated at the potential explosion site (PES) is critical at an exposed site (ES) over a significant range of standoff distances. The Science Panel Impact Debris Evaluation and Review (SPIDER) test program has been planned to develop improved predictions for the hazards inside an ES by fragments and debris. Data will include the mass and velocity required for perforation of the test cross-section and the characteristics of all debris produced inside the ES.

Jan 1, 2010

By John W. Brown

"Adequate dust control in and around rock drills is a problem that must be solvedfor the health and safety of workers running the drill as well as those working around thedrilling operation This paper will discuss the designs available from most drill manufacturers todayand the effort ‘nvolved in keeping them effective on a productive basis."

Jan 1, 1999

By Kyle Apple

The following is a case study of how LuckStone Corporation improved their blast monitoring and documentation program. A number of resources already at their disposal have been utilized to improve the body of data collected from each blast. The tools being used include GPS, aerial photos, and a user-friendly push button format excel spreadsheet. The data collected include product by product records of materials used, distances to all concerned neighbors, seismograph data, etc: The spreadsheet has been designed to perform an ongoing analysis of blasting trends. The program has been carried out at a corporate level and is in use by blasters at each location. This paper addresses the advantages and drawbacks of this program. It also addresses the ways in which the various tools were integrated, Discussed as well is the need for simplicity when bringing “new” technology to the field and the steps taken in familiarizing the end user to changes.

Jan 1, 2001

By Rob Lederer, Chris Batten

Traditionally coal model digital terrain models (DTM) are created from lithological information obtained from broad scale exploration holes. The grid layout and distance between holes means that models do not commonly display local variations of seam dip, faulting and shearing. Due to this, issues can often arise when designing the loading of blast patterns based on potential variances between model and actual coal seam locations. Many sites will often attempt to create more accurate models through the collection of data from coal edge pickups on highwalls and in blast faces, along with information recorded by drillers (touch coal holes) from both production and presplit holes for both the current and previous blasts.

Jan 1, 2012

By Patricio González Santis, Jacopo Seccatore

This paper documents drilling and blasting activities from gold mining in Ecuador and Chile. First, are described the outdated and often non-rational techniques employed by miners, to provide a general framework of the current methods. Then, it is shown what can be improved and how the current methods can be modified. Finally, are shown some field applications and the comparisons of the results obtained

Feb 1, 2020

By Mark Svinkin

To save time for construction of coal pits, the contractor decided to combine erection of the tower pitheads with digging of skip shafts to the depth necessary for placing proper coal pit equipment. It was obvious that blasts used in shaft faces and lifting machines installed at a lower part of the pithead could excite vibrations of an upper part of the pithead with curing concrete. The contractor was concerned about vibrations of pithead concrete structures and the disturbance of freshly poured concrete in forms at a top of the pithead as a consequence of structure vibrations. The results of a study of the tower pithead structure vibrations from blasting and operating machinery, and effects of structural vibrations on curing concrete are presented. Structural vibrations were measured at the tower pitheads of two coal pits from twelve blasts. Records of horizontal and vertical displacements were superposition of harmonic low-frequency damped vibrations and sporadic high-frequency damped vibrations with a variable frequency. Low frequency vibrations attenuated during 8-13 s after the last delayed blast. Measured values of the natural frequencies of pithead horizontal vibrations coincided with the calculated frequencies of horizontal bend vibrations. An increase of a face depth from 18 to 50 m diminished 16 times horizontal bending vibration displacements of concrete structures. Measurements of vertical structural vibrations from blasting demonstrated increasing of vertical pithead displacements with the rising of structure elevations. This is evidence of the pithead longitudinal tension. The holes with charges were not properly condensed for one blast. As a result of incompact stemming, the blast substantially increased the energy of airborne pressure waves, which triggered natural vertical vibrations of the pithead with high displacements.

Jan 1, 2004

By A. Ravi Kumar

A trench is a structure to accommodate fluid carrying pipelines for water, gas, petroleum products etc. Trench serves the purpose to haul the fluids in bulk over long distances safely and economically. Use of pipeline for moving oil and gas was essentially a post World War II development, but now it has acquired its own importance.

Jan 1, 2008

By Behrouz Ohadi, Kamran Esmaeili, Bibhu Mohanty

In most metalliferrous open pit mines with heterogeneous orebodies, blast-induced rock movement is a crucial outcome that has unfavorable impact on ore and waste segregation in the post-blast muck pile, resulting in either ore loss (the ore is misclassified as waste and sent to the waste rock dump) and/or ore dilution (waste is misclassified as ore and sent to the processing plant). While many studies have been carried out to assess the influence of blast design parameters on blast-induced rock movement, the influence of rock mass characteristics in these studies have been overlooked.

Jan 1, 2018