Search Documents

To maximise recovery by highwall mining, pillars must be designed which are long, slender and of relatively low width-to-height ratios. The strength of pillars with width/height less than 2 depends primarily on the mechanical response of the coal, due to the reduced influence of frictional restraint between roof and floor. A suitable pillar design approach therefore requires a method of estimating coal-seam properties. Experimental studies were carried out to determine ways of reliably predicting the large-scale mechanical properties of coal seams from small-scale test data. The studies led to a method of practical, systematic assessment of coal-seam properties based on measurement of coal rank and seam brightness profiles. The criterion employs the parameters sigma(c), m and s of the generalised Hoek-Brown empirical strength criterion for rock masses. A novel design approach combines the flexibility of modern numerical modelling programs with simple hand calculation for rapid assessment

Jun 21, 1905

By J. D. Appleton, J. Ridgway, K. B. Greally

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The results suggest that meaningful geochemical maps can be produced from very low-density surveys, and that existing data sets could perhaps be incorporated into such a map series with the use of a system such as Uniras software. There are still many problems to be resolved, however, including the compatibility of data derived from different analytical methods, and the precise methods to be employed will necessarily require international agreement. Sampling densities should be chosen on the basis of the scale of the geochemical and geological features to be distinguished and will vary from region to region. Reanalysis of selected samples from archives to increase the range of elements determined or to unify analytical methods is only likely to be effective if the original survey was at quite a low density

Jul 1, 1991

By G. G. Barbante

The oxidation behaviour of selenide matte with a substantial Cu content and low Ag differs significantly from that of high-Ag matte. Low-Ag selenide mattes display a large oxygen solubility and the upper boundary of the miscibility gap in the Ag-Cu-Se-O system is depressed to quite low Se contents. As a result, the formation of Ag metal is considerably delayed. The oxidised selenide matte, low in Se and with a relatively high oxygen content, has previously been termed oxymelt. With further oxidation, its composition enters the misciblity gap and crude Ag is formed. The sodium silicate slag captures very little of the SeO2 and the dissolved Ag2O(s) content of the slag is relatively small, with a Raoultian activity coefficient of 0.57. This value was found to be independent of the slag's Cu2O content

Jun 19, 1905

By R. H. T. Garnett

N.B. This paper provoked much (positive!) discussion in later issues, with responses from the author (and thanks also for the many private contributions he had received) - see under Garnett R.H.T. Expanded version of a paper originally presented at the Alluvial mining conference, London, 11-13 November 1991 and published in Alluvial mining, Barking: Elsevier Applied Science for IMM, 1991, p.115-156. The usual measure of performance in gold and tin dredging is the R/E factor. It compares actual production or recovered grade for a given period with that estimated from the original sampling. The factor is a multiple of four component factors, each ideally approaching 1.00. The factors are concerned with estimation, selection, excavation and treatment. The estimation factor reflects the errors involved in determining the grade and depth of single drill-holes or pits. An optimum selection factor is achieved by a higher drilling density. The excavation factor is affected by failure of the dredge to excavate the total volume contained within its course. The required dredge throughput rate influences not only the success in digging recovery but also the treatment factor. No two alluvial deposits are the same, but, in general, the greatest divergence from 1.00 is invariably demonstrated by the estimation factor. A major divergence in one of the other factors may also be the cause of the R/E factor being significantly different from 1.00. The component factors are examined in detail and historical trends in R/E factors are discussed

Sep 1, 1991

By V. A. Melezhik, A. H. Green, L. N. Grinenko

Finally, a theoretical model is constructed that takes

Aug 1, 1994

By M. J. Howes

The high degree of mechanisation, which is mainly diesel-powered, has a significant effect on heat loads; heat output from this source often exceeds the heat flow from the surrounding rock. The extensive use of diesel-powered equipment also influences ventilation rates and minimum values are necessary to ensure that emissions of diesel exhaust are adequately diluted. Many Australian mines are in subtropical or tropical areas with high ambient wet- and dry-bulb temperatures on surface. This, coupled with the large amount of heat from mechanisation, usually means that refrigeration is required at much shallower depths. A secondary problem is associated with the definition of acceptable thermal environment conditions, which are sometimes based on the assumption of no air movement. This gives rise to very stringent thermal environment acceptance criteria, which, in some areas, would prohibit work on surface, let alone underground

Jun 12, 1905

By S. Kelebek, J. A. Finch, Zhenghe Xu, S. R. (Ram) Rao

To improve SO2 emission compliance, pyrrhotite from Sudbury copper-nickel ores is being depressed with DETA. To understand the mechanism of depression, the role of complexing in controlling metal-ion activation of pyrrhotite was investigated. DETA was found to remove Cu and Ni ions but leave hydrophilic ferric species on the pyrrhotite surface. The metal:DETA ratio appeared to be 1:2. Cu was more readily removed than Ni, but the combination of DETA with sulphur dioxide was equally effective for both metal ions. Certain combinations of DETA, Ni ions, xanthate and dithionite (S2O4) or dithionate (S2O6), as representative derivatives of SO2 in water, produced hydrophilic precipitates. These may enhance pyrrhotite depression

Jun 19, 1905

By C. S. Spirakis, A. V. Heyl

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The modified basinal brines, containing partly oxidised sulphur species, scavenged metals from basement rocks and sediments and transported them through the host rock, which contained local concentrations of organic matter. Reacting in various ways with the mineralising solution as temperatures at the sites of mineralisation changed, organic matter caused the precipitation and dissolution of a variety of minerals in the ore zones; it was organic matter that caused all of these reactions to occur at the same sites. Thus all components of the mineralising fluid - salt, water, heat, sulphur and metals - were obtained within the ore district. The siting of the mineral districts was related to the locations of faults through U- and Th-enriched granites beneath sediments containing basinal brines, and the locations of ore deposits within the districts were controlled by local concentrations of organic matter

Apr 1, 1995

By L. J. Cabri, J. M. D. Wilson, R Lastra

An image analysis program can search for gold minerals in polished sections by scanning about 100 x 100 back-scattered electron images at a magnification of x400, allowing gold grains as small as 1 micrometre in diameter to be detected. Typically, a c.15 h overnight search of a product smaller than 45 micrometres will scan c.1 500 000 particles, providing data that are not easily obtained through manual operation of an optical microscope. The program locates grains of the correct brightness, acquires gold X-rays from them by wavelength-dispersive spectrometry, filters the data to remove artefacts and record the images and stage locations for subsequent retrieval. At the end of the run, the program allows the operator to verify and identify the grains found. Industrial studies at Canmet have included determining the nature of gold in cyanidation tailings, checking the mineralogy and size of gold grains in samples from an Indonesian Cu-Au concentrator and locating and measuring gold liberation and grain sizes in an ore

Jun 21, 1905

By G. Adachi, K. Machida, T. Ozaki, K. Murase

The chlorination rate with CCl4 was unexpectedly slower than carbochlorination using chlorine under the same reaction conditions. Chlorination with CCl4 was topochemical and the amount of monazite reacted after different periods suggested that the kinetic control step was the reaction between CCl4 and the monazite core at the interface. The kinetic order of the reaction was 0.5. The presence of a complex former, AlCl3, promoted the chemical vapour transport of rare-earth chlorides as complexes

Jun 18, 1905

By R. A. Lord, H. M. Prichard

efficiency is discussed from both experimental and

Apr 1, 1994

By R. Sankey, L. Gatty, F. Bizzozero, G. F. Shannon, F. Savaglio, L. McDonald

State mining regulations in Queensland stipulate that a mine be provided with an earth installed on surface and that all underground equipment that needs to be earthed should be connected via a copper conductor to this surface grounding point. The regulations further require that all exposed metal surfaces in underground substations be connected to an earth. In a study of earthing conditions at Mount Isa mine it was found that the physical anchoring of metal work at substations (with rockbolts and associated steel mesh) also provides an excellent electrical connection to the country rock. It was established that not only is the mine's earthing system grounded at numerous underground locations but also that such anchor points offer, in general, a path to ground with lower resistance than does the legally required grounding point on the surface. It is recommended that metalliferous mines should utilise a multiple-earth system and not a run earth connected to a single, above-ground earth point

May 1, 1991

By G. M. Steed, A. O. Oyinloye

The deposit lies in amphibolite-facies biotite granite-gneisses of Proterozoic age, 4 km east of a major crustal break known as the Ifewara-Zungeru fault. Gold mineralisation is contained in a zone of quartz-carbonate (mainly calcite) veins and hydrothermally altered gneisses with associated small-scale intrusions along a steeply dipping second-order fault zone that roughly parallels the main fault. Gold is present mainly at grain boundaries between quartz and carbonate as discrete particles up to 100 micrometres in size, in general association with sparse, scattered pyrite, pyrrhotite and some base metal sulphides. Adjacent to the gold-bearing zone the granite-gneisses have been hydrothermally altered with minor volume increase, most notable enrichment being in K2O, S, Pb and Cu (and Au). High concentrations of Th, Y, Ce and Zr in the granite-gneisses imply derivation from S-type granites. It is likely that their high heat production capacity maintained the high temperatures needed to transport gold in the hydrothermal systems. It is most probable that the mineralisation dates from the Pan-African orogeny (650-450 Ma)

Apr 1, 1996

By G. J. Hearn

between particles in the classifying region is then

Apr 1, 1995

By I. Marklund, W. Hustrulid

Sublevel caving is likely to remain the dominant system at both Malmberget and Kiruna for the foreseeable future. The sub-level interval has increased from 12 m in 1983 to 30 m, requiring more effective drifting and the development of a contour blasting technique to reduce requirements for rock reinforcement. Production drilling is mainly by hydraulic hammers or water-powered in-the-hole machines drilling 115 m diameter holes. Loading operations are undertaken 7 days/week with 15-25 tonne capacity electric shovels. Production has increased by nearly 70% since 1983 and productivity has risen threefold

Dec 1, 1995

By J. E. Misiewicz, A Rozendaal

Paper presented at Geofluids '93, held in Torquay, UK, 4-7 May 1993. The tin field consists of a fragment of Lower Proterozoic volcanosedimentary rocks surrounded by granitoids. Almost all the significant deposits are hosted by arkoses and are classified as replacement and space-filling types, with particular styles of mineralisation dominating at different mines. Petrological and geochemical investigation of borehole cores from four centres indicated the presence of a stratified zone 500-600 m thick and continuous over at least 20 km along strike, consisting of pervasively altered clastic arenitic sediments. The alteration is zoned into a grey-green sodic albitised footwall, an 80 m thick sericitised-tourmalinised sulphidic tin zone and a red haematitic potassic hanging-wall. The zoning and the localisation of three cassiterite phases are consistent with the tectonic history and with multiple pulses of stanniferous hydrothermal fluids derived from late differentiates of the granites over a prolonged period. Areas of high fracture density acted as conduits for the fluids, whose initially rapid ascent was retarded by decreasing pressure contrast, limited development of fracturing and/or impermeable shaly arkose to cause lateral spreading and pervasive alteration over a broad, stratified front. Lateral overlapping of local fronts at the various centres suggests a continuous zone, while the many petrological and geochemical similarities point to a shared fluid composition

Aug 1, 1995

By T Grenne, R. B. Larsen

Paper presented at the conference on Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. Paper originally entitled: Processes in a newly discovered sulphide-PGE mineralisation in Norway. The Stormyrplutten mineralisation is hosted by a minor tholeiitic metagabbro of low-Ti composition intruded at a high level in the volcanic lithology. It is thought to be the subvolcanic counterpart of submarine basalts generated during an extensional episode of ensimatic arc evolution. The sulphide-PGE mineralisation occurs as stratabound pyrite, pyrrhotite and chalcopyrite disseminations with average grades of 376 ppb Pd, 313 ppb Pt, 40 ppb Au, 0.5% Cu and 0.08% Ni in a deposit 15-25 m thick. Locally the PGE content peaks at 2 ppm over 1 m. Microprobe analysis isolated 14 different platinum-group minerals, dominated by sperrylite, temagamite and borovskite and occurring as 1-20 micron compounds embedded in the main sulphide minerals or along the sulphide/silicate grain boundaries. Mantle-normalised plots reveal strong depletion in Os, Ir and Ru and enrichment in Pt, Pd, Cu and Au. The general decrease in Pd and Pt and increase in S up through the stratigraphy is similar to PGE distribution in the Darwendale subchamber of the Great Dyke in Zimbabwe, and may reflect strong fractionation of Pd and Pt in favour of the first droplets of sulphide melt; two reversals of the trend at the 4 and 12 metre levels represent replenishment with fresh magma and repetition of the cycle. In contrast to the Darwendale system, Cu and Ni also show peak concentrations in the first-formed liquids and Pt appears to have fractionated more strongly into the sulphide melt than Pd

Aug 1, 1995

By G. W. Harris, J. J. K. Daemen

Slightly shorter, modified version also published in CIM Bull., vol.94, no.1047, Feb. 2001, p.52-55. To minimise ore dilution induced by blast movement in surface mines it is necessary to quantify such movement. This will allow more accurate location of the grade boundaries on the surface of a blasted rock pile before excavation. A method has been developed and tested for measuring accurately the direction and magnitude of subsurface blast movement, using a caesium vapour gradiometer and a real-time, differentially corrected global positioning system to locate the pre- and post-blast positions of magnetically enhanced target objects placed in blastholes inside a bench. The procedure does not necessitate disturbance of the blasted rock and the movement information is available sufficiently quickly to allow for modification of the selective mining boundaries for each surveyed blast. It was found that the maximum depth of target detection was 18 m and the overall accuracy was plus or minus 1 m horizontally and 1.2 m vertically

Jun 21, 1905

By Bakker J. de, P. A. Leest, W. L. Dalmijn, H. J. Glass

The test facility at the Delft University of Technology, in the Netherlands, was characterised. Advantages include the possibility of separating particles with high but different densities up to 9 g/cm3, the ease of adjustment to any required separation density and the absence of moving parts. Simultaneous separation of more than two types of particles is possible and the magnetic fluid is safe and convenient to use compared with other heavy liquids. Disadvantages include loss of magnetic fluid with outgoing particles (cost approx US $10/l) and degeneration of fluid due to bacterial activity, reaction with particles and with surroundings. Only non-magnetic materials can be separated, there is limited potential for scaling up and high investment is required on account of the cost of magnets. Future improvements in the design of the apparatus and the properties of the magnetic fluids can only enhance its attractiveness for commercial applications

Jun 18, 1905

By R. A. D. Pattrick, R. A. F. Ixer

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. At Calliachar Burn, 14 steeply dipping quartz-sulphide veins, with and without gold, infill master joints that crosscut gently dipping metasediments and metabasics of the Pitlochry Schist Formation. The wallrock is extremely bleached and enriched in sericite, chlorite and carbonate. Gold grades vary from high with quartz-galena-pyrite to low with galena-chalcopyrite; the gold forms electrum inclusions smaller than 20 micrometres in pyrite or, rarely, arsenopyrite. At Urlar Burn, gold is present in small amounts in 4 quartz-galena-chalcopyrite veins. Although much of the mineralogy is similar to that at Calliachar, there are significant differences in Sb-, Te-, Bi- and Hg-bearing phases. Fluid inclusion data suggest mineralisation occurred over the range 320-140 degrees C, from fluids with significant CO2 and 2-13 wt% equiv. NaCl. Mantle-derived fluids appear to have been generated during the late Caledonian and focused by the Urlar Burn fault

Jun 19, 1905