Search Documents

By Lei Zhang, Xianjun Lu1, Minjie Lian, Liyang Zheng

In order to investigate rheological behaviour of fine tailings backfill pastes, the fine iron ore tailings (size fraction of -0.074mm accounts for 70%) from Fuquan Mining Co., Ltd. of Sinosteel Corporation (Shandong, China) was investigated. The rheological parameters such as slump, viscosity and yield stress of the tailings pastes under different densities were measured in detail, and the effect of paste density on the rheological property and the relationships of different rheological parameters of the pastes were also discussed. According to the results, the rheological behaviour is in accordance with the pseudoplastic fluid in a wide range of paste densities (solid content, w/w) of 65% to 80% and the pastes turn to be Bingham fluids at higher shearing rates. Along with the increase of paste density, the slump drops gradually and the viscosity and shear stress increase gradually. However, the variation extent of the rheological parameters varies at different density ranges. According to the variation pattern of the rheological parameters at different paste densities, the flow ability of the pastes can be classified into three zones. The high fluidity zone was observed at the density range of 65%-69% where the rheological parameters vary slightly along with the paste density, the moderate fluidity zone was observed at the density range of 70%-76% where the rheological parameters vary significantly along with the paste density, and the low fluidity zone was observed at the density range of more than 76% where the rheological parameters vary sharply along with the paste density and the critical density for this sudden variation is about 76%. Furthermore, linear correlations of slump/viscosity and slump/yield stress were observed. It is possible to predict the viscosity and yield stress of the pastes based on the slump measurements.

Jan 1, 2014

By N. Naude, W. P. Roux

"Traditionally minerals processing equipment, such as jigs, are studied by characterising the feed and products from these processes. With this approach important details on the mechanisms of a process can be overlooked since assumptions have to be made on the internal operations of the equipment. Positron Emission Particle Tracking (PEPT) is a non-invasive technique that can be used to track a particle’s movement inside a closed vessel. PEPT makes it possible to observe the inner workings of a process, providing new information that was unattainable only a few years ago. Jigging has long been considered as one of the most difficult mineral processing techniques to model, due to the complexity of the mechanisms contributing to the separation of minerals during the jigging process. In this investigation PEPT was used to study the particle flow inside a laboratory batch jig. The aim was to determine if the particle trajectories could provide new insight into the jigging and its mechanisms. Three dimensional particle trajectories were observed with spatial and temporal resolution high enough to see details of the individual pulses during jigging. It was found that the pulse height is very dependent on the position in the jig bed. The vertical component from the trajectories showed the rate at which particles move through the jig bed (stratification rate) and it was seen that the density of a particle affects the stratification rate more that the particle’s size and that the shape in the range that was tested had little to no influence. Other phenomena such as a circular flow pattern was observed inside the jig and it was found that smaller lower density particles are affected by this circular flow pattern which tend to disperse these particles throughout the jig bed. Visualising the flow inside a jig by means of PEPT has shown to be instrumental in the deeper understanding of the process."

Jan 1, 2018

By R. Prakash

Column flotation has now gained wide application in the recovery of various minerals. The performance of the flotation device depends on the mixing characteristics of the phases inside the devices. In this work, quality of mixing in a flotation column has been analyzed by using information entropy theory. Empirical models have been developed for flotation column with the parameters which affect the quality of mixing. The efficiency of the particle separation in the flotation column has been enunciated based on the quality of mixing. The present analysis on the quality of mixing in flotation column may give insight into a further understanding and modeling of flotation devices in industrial applications.

Sep 1, 2012

By E. Ashirbaeva

"Ores of ferrous metals traditionally make up the bulk of recoverable reserves of solid minerals, and iron ore concentrates - in the processing and consumption. To obtain concentrates, three main methods are used: dry and wet magnetic separation, gravity and flotation. But even their integration into complex developed schemes with finishing operations often do not solve the problem of obtaining high-quality concentrates, which are necessary for powder metallurgy and electric steelmaking. Increasing the iron content in the concentrate by removing harmful impurities is the goal of this work. The possibility of reducing the operations of wet magnetic separation twice and completely eliminating concentrating operations in ball mills from the scheme of operations has been established. Selective leaching agents for each type of iron ores have been created, allowing to obtain concentrates with an iron content of not less than 68-69% and negligible concentrations of harmful impurities. Methodical recommendations for long-term storage of bioreagents in the active state, their immobilization and preparation in industrial conditions at the enterprise Nedropolzovatelja are developed. The proposed biotechnology, which allows to obtain high quality iron and conditional concentrates for harmful impurities, is protected by patents (RU 2537684 ""Method for fine-tuning of high-sulfur magnetite concentrate"" for magnetite ores and Pat. RU 2599068. For the industrial implementation of the new technology, organizational and technological measures have been developed in the system with Road maps for types of ores. The developed technology makes it possible to condition noble metal, tin, tungsten, nickel and other concentrates in harmful impurities such as arsenic, antimony, mercury, sulfur, copper, zinc, iron, phosphorus, manganese, in total 30 components that pass into solution under the influence of bioreagents.INTRODUCTION Consumption of various metals is steadily increasing every year, the volume of mining is constantly increasing. Ores of ferrous metals traditionally make up the bulk of the recoverable reserves of solid minerals. Enrichment technologies for iron-containing ores are reduced to the combination of three main methods: wet and dry magnetic separation, gravity and flotation. But even the use of complex advanced technological schemes often does not lead to the production of high-quality concentrates suitable for metallurgical processing. In this case, either lapping operations or effective technical and technological solutions are used in the main enrichment cycle. Widely used in practice methods for improving the quality of iron ore concentrates include the use of finishing operations (fine screening, reverse cation flotation), staging of concentrates, the use of more sophisticated equipment (separators with running magnetic field, magnetic gravity classifiers, column flotation machines)."

Jan 1, 2018

By Alan Bye, Nick Beaton, Wayne Stange, Emmy Manlapig, James Groutsch

"For over 50 years the JKMRC has applied a unique education-based research strategy to develop modelling and simulation tools that are "fit for purpose" for industrial application. These tools are widely used for the analysis and optimisation of mining and mineral processing systems. As the mining industry context evolves to deal with declining head grades, falling commodity prices, professional skill shortages, and an exponential growth in the volume of data, a re-evaluation of what "fit for purpose" means in the future is required. It is contended that future industry needs for simulation-based decision support requires tools and systems that incorporate: • Multi-component modelling, • Models of complex sensor behaviour, • Integration across the physical value-chain e.g. resource to market, • Financial analysis including risk and uncertainty assessment, • Enabling multi-criterion decision making (technical, financial and environmental), • Ore-body knowledge at multiple scales, • The use of fundamental numerical models to provide insight for the development of practically useful models, and • Decision support delivered through remote operations centres. JKMRC and CRC-ORE are collaborating to develop a next-generation simulation-based decision support system that assists in addressing these challenges. The Integrated Extraction Simulator (IES) combines many years of pragmatic and successful work integrated with modern technology trends - in particular the rapid move to cloud-based computing."

Jan 1, 2014

By Y. H. Tang, H. Y. Zhang

"Tailings from lead-zinc mine contain plenty of dolomite and low-grade fine-grained barite, which is difficult to enrich by mineral processing. Since the density of barite and dolomite has some differences due to the fine dissemination size in a complex sedimentary, the gravity separation tests were conducted with no results obtained. The magnetic separation was conducted to remove the magnetic gangues, and the results were not satisfactory because of the gangue minerals such as limonite and others were low in content. The results of floatation tests showed that the mineral separation of barite and dolomite is quite difficult because that they have similar mineral floatability. Experimental research shows that the good results can be obtained by “desulfurizationbarite floatation” processing with the new depressant TS. The barite concentrate containing BaSO4 91.27%, BaSO4recovery is 70.25% when sodium dodecyl sulfonate serves as a collector and TS as the depressant.INTRODUCTIONBarite is an important mineral material. Often associated with other minerals, it usually needs to be separated by mineral processing in order to meet the application requirements. The main barite beneficiation methods include hand sorting, gravity separation, floatation, magnetic separation, acid leaching, etc. Usually barite associated with oxide ore such as fluorite dolomite, quartz ore etc. are also associated with sulfide ore such as pyrite, sphalerite and galena. The separation between barite and sulfide ore (such as pyrite) is easy. On the other hand, the separation between barite and oxide ore (such as dolomite and fluorite) is very difficult. There are quite a lot of reports on the separation between barite with fluorite dolomite however the separation between barite and dolomite is seldom discussed.The ore properties are quite complex attributable to mineral assemblage containing a large amounts of dolomite. As the density of barite and dolomite has some differences, gravity separation between them is usually easy. The gravity separation tests were conducted with no results obtained due to the fine dissemination size in a complex sedimentary. The magnetic separation was conducted to remove the magnetic gangues, and the results are not satisfactory as the gangue minerals such as limonite and others were low in content. Due to the fine dissemination and intimate association of minerals, and barite and dolomite contain the same group ions of Ba2+, Ca2+ and Mg2+, the results of flotation tests showed that the mineral separation between barite and dolomite by flotation means problematic. Previous studies have been conducted by several institutions but none to date has come up with a satisfactory process in dealing with the deposit. This may be attributable to: high cost of reagents; unsatisfactory performance. Therefore, the key to the flotation separation of barite and dolomite is the application of selective inhibitors. Based on previous test observations and years of extensive research experience in barite processing technology, with the new depressant TS has selectivity inhibition on dolomite developed and used, good results can be obtained by “desulfurization-barite flotation”, which allows barite in the lead-zinc tailings to a comprehensive recovery."

Jan 1, 2018

By Svetlana Krashenina, Nebojsa Petrovic, Oscar Lopez

"As easily mined gold deposits are becoming increasingly rare, gold producers are turning to the processing of ores with polymetallic and copper mineralization. These base metals can create metallurgical and waste handling/disposal challenges, which can render the project uneconomic. Base metals such as copper compete for the cyanide reagent used to extract gold, necessitating the need to increase cyanide volumes and consequently, cyanide consumption costs. Copper will also stabilize in tailings water as weak acid dissociable cyanide, a form that is both difficult and costly to destruct. SART (sulphidization-acidification-recycling-thickening) process technology can be applied to remove base metal interferences in gold projects. SART breaks the copper-cyanide complex and precipitates the copper as a saleable copper sulphide concentrate. With the copper removed, the cyanide can be regenerated as free cyanide for recycle to the gold recovery process. This improves cyanide utilization efficiency and mitigates copper presence in tailings. Additionally, copper recovery generates an incremental revenue source to further improve project economics. Engineering Dobersek GmbH together with BioteQ developed a SART and AVR testing program to recover cyanide and maximize operational efficiencies at a gold processing plant in Kazakhstan with high cyanide consumption in the leach circuit. Results from on-site testing demonstrated that up to 99.98% of copper can be removed and precipitated as copper sulphide and 60-90% of cyanide can be recovered from the AVR and recycled for leaching, reducing total overall cyanide use. This paper provides an overview of the testing methodology and results together with a discussion on the potential of SART to improve gold production operations to deliver both environmental and economic benefits."

Jan 1, 2014

By A. Güney

Currently, recycling technologies use relatively homogeneous plastics because hand-sorting waste feed is too expensive. Many promising technologies for separating mixed thermoplastics are being investigated, but they are still uneconomical and unreliable. Burning plastics for recycling is not used because of poisonous gases released when their burning. PET and PVC cannot be separated using conventional gravity separation techniques because their specific gravities overlap; PET density changes from 1.33 g/cc to 1.37 g/cc and PVC density is between 1.32 g/cc and 1.37 g/cc. For this reason, plastic recycling needs new techniques. Among these techniques froth flotation, also used in mineral processing, can be useful for its cost and simplicity. In this method, a plastic is selected from mixture, tried to regain its natural property, hydrophobicity. In this study the experiments were applied by using plasticizer reagents to make the selected plastics hydrophobic and us-ing NaOH to render the other hydrophilic. Post-consumed PET and PVC are evaluated by concerning the effects of selected parameters (particle size, concentration of plasticizer reagent, amount of NaOH, conditioning time and the effect of conditioning temperature). At the end of the experiments, optimum parameters for selective flotation of PET from PVC was found as particle size of -4.76 + 3.36 mm, NaOH amount of 30 kg/t, conditioning temperature of 75°C, conditioning time of 30 minutes, reagent amount of 300 mg/L. Consequently, PET was re-covered with 99.7% purity and 57% efficiency.

Jan 1, 2014

By Gábor Mucsi, Barnabás Csoke, Viktor Mádai, Zoltán Molnár, Viktor Török, Ádám Rácz

The application of the stirred media mill in dry mode came to the front only in recent years, but at the same time several questions arise, such as aggregation, agglomeration, sticking on the liners and the grinding media. During high energy milling, not only the particle size reduces, but among others, in numerous cases the crystal structure and the amorphous state of the material also change due to the mechanical activation taking place. The present paper deals with experiments carried out on the ultrafine fly ash grinding in dry mode at various grinding conditions in a stirred media mill to investigate the mechanochemical effect and the energy efficiency of the mill. During the experiments the particle size distribution, particle shape, specific surface area, amorphity and crystal structure of the products were examined. The product related stress model was used for the evaluation of the effect of milling parameters on the mechanical activation. It was found, based on the experimental results, that there is mechanochemical effect on crystal structure of fly ash in the stirred media mill, as it was revealed by X-ray diffraction and FTIR measurements. The experimental results made it possible to determine the effect of the rotor circumferential speed and so the stress intensity on the mechanical activation of fly ash could be revealed.

Jan 1, 2014

By Leopoldo Gutierrez, Esau Arinaitwe, Marek Pawlik

"The effect of various polymers, including: anionic carboxymethyl cellulose (CMC), polystyrene sulfonate (PSS), humic acids (HA) and non-ionic hydroxypropyl cellulose, on the wettability of Athabasca bitumen was evaluated through dynamic contact angle measurements using the captive bubble technique. The tests were carried out as a function of pH at a constant ionic strength (0.01 mol/L sodium chloride). The evolution of the three-phase contact angle between the solution, bitumen and an air bubble was followed as a function of time over a period of ~6 minutes. The contact angle data were modelled using a first-order kinetic equation. The results were analyzed in terms of the initial contact angle, the evolution rate constant, and the steady-state contact angle value. In the case of anionic polymers, a pronounced decrease in the initial contact angle value was observed at pH 3. Under acidic conditions, there was no significant effect of CMC observed on the steady-state contact angle value but PSS and HA significantly decreased the steady-state contact angle value. At pH 8.5. the anionic polymers did not affect the wettability of the bitumen surface but they significantly decreased the contact angle evolution rate. These results suggested that CMC is not capable of permanently lowering the hydrophobicity of bitumen, and the polymer only slowed down the evolution of the contact angle to the steady-state value. The results also showed that polystyrene sulfonate and humic acids were capable of making bitumen hydrophilic but only under acidic conditions. Only hydroxypropyl cellulose (HPC) produced a large decrease in the steady-state contact angle under alkaline conditions (pH 8.5). The kinetics of contact angle evolution in the presence of HPC was also drastically lowered. The results were discussed in terms of the chemical composition of the polymers and their different affinities towards the bitumen surface."

Jan 1, 2014

By Ljubisa Obradovic, Baisui Han, Batnasan Altansukh, Zoran Stevanovic, Atsushi Shibayama, Jonovic Radojka, Daizo Ishiyama, Kazutoshi Hag, Radmila Markovic, Ljiljana Avramovic

This paper discussed a combined froth flotation and high pressure leaching (HPL) process to recover copper from mine tailings. At first, froth flotation were carried out using the mine tailings sample under various conditions in the presence of different pH (3.5-10) and sulfurizing reagent value (0-1000 g/t), respectively. As a result, optimum condition (sulfurizing reagent of 1000 g/t, pH of 10, PAX (collector) of 100 g/t and MIBC (frother) of 200 g/t) was found for froth flotation of copper. The effects of sulphuric acid concentration, leaching temperature, total pressure (steam pressure plus oxygen pressure) on high pressure leaching (HPL) of mine tailing were investigated using sulphuric acid solution in the presence of oxygen. The best conditions for HPL were obtained to be sulphuric acid concentration: 0 mol/L (water), leaching temperature: 170 ?, total pressure: 2 MPa, leaching time: 1 hr and pulp density: 100 g/L. The leaching rate of copper reached nearly 99 % and the concentration of copper in pregnant leach solution (PLS) was 0.24 g/L. Finally, copper in the mine tailing was recovered using froth flotation followed by HPL. As a result of a combined froth flotation and HPL, the vast majority of copper (99 %) from the mine tailings was extracted.

Jan 1, 2014

"The business importance of water for mining companies is unequivocal as it may affect several aspects of mining projects ranging from the life-and-death license to operate to the imperative economic viability. It is thus no wonder that nearly all mining companies acknowledge water-related risks, issues and opportunities in their respective sustainability report. Somehow, this procedure has fostered the idea that water frugality could be the sustainable solution to several water-related issues. The regular exercise of water accounting should then follow as a key strategic requirement. Water accounting is defined as the application of a consistent and structured approach to identifying, measuring, recording and reporting information about water. However, several factors discussed herein have led to the fact that some water accounts are still produced using means (hardware and software) which undermatch the value actually associated with water. The resulting fuzziness about water usage could result in missed opportunities, suboptimal operations or even lead to environmental law violations. This paper subscribes to the distinctive perspective that, once underlying concepts and practical definitions have been standardized under a supported framework, such as the openly available Water Accounting Framework (WAF) published by the Minerals Council of Australia, most of the remaining water accounting issues may be boiled down to accuracy issues and, ultimately, to how much accuracy is valued by the stakeholders. Using the latest WAF document as a baseline for best practices of water accounting and, borrowing concepts from the fields of sensor network design in the process industries and best practices of metal accounting, this paper reviews some essential accuracy issues to be considered when designing or analyzing water accounting systems in mineral processing. The current paper also includes some elements for a promising attempt to include the value of information paradigm inside the water accounting best practices."

Jan 1, 2014

Gold thiosulfate complex is difference with gold cyanide complex, which is easily adsorbed on activated carbon while gold thiosulfate complex cannot be satisfactorily recovered by activated car-bon. However, Gold thiosulfate could be recovered by activated carbon if cyanide is added into the thiosulfate solution. To avoid the cyanide solution, this paper will review several possible processes to recover the gold from thiosuldate solution: such as the cementation with metals, ion exchange resin and solvent extraction. The gold cementation with the powders of zinc, copper, iron and aluminium will be discussed. The advantage and disadvantage of each are compared. The consumption of thiosulfate and copper and feasibility of solution recycling will be discussed. The gold recovery by some ion exchange resins will be suggested. The processing conditions, its applications and the resin elution methods will be presented. The gold recovery by using solvent ex-traction will be reviewed. The processing conditions of solvent extraction process are discussed and compared.

Jan 1, 2014

By Wolfgang Öfner

Many technical processes also yield dusty residues which usually contain appreciable amounts of valuable matter. Often they also accumulate substances detrimental to the process. Dumping them entirely in landfills wastes raw material and causes high disposal costs, but recycling them without prior treatment is often not feasible. Physical separation processes are preferable because of their rather low energy demand. In order to develop such treatment systematically, the residues must be characterized properly. The technique for such a characterization is taken from mineral processing: perfect fractionation according to continuous properties of the particles supplemented with chemical analysis are used for plotting the Henry-Reinhardt chart. This represents the benchmark for assessing actual separation processes and tests. Their results are compared in terms of ?selectivity? and plotted in the kappa chart. In this paper, Henry-Reinhardt chart and kappa chart are applied to several different types of residues from iron and steel production and show their potential for being upgraded before reutilization in the production process. This approach is suitable for virtually all dusty residues from other industrial processes as well. Keywords: residue, dust,iron and steel, process development, Henry-Reinhardt chart, kappa chart

Sep 1, 2012

By Kazutoshi Haga, Batnasan Altansukh, Shirchinnamjil Nyamdelger, Atsushi Shibayama, Narankhuu Ariunbolor, Gunchin Burmaa

In this study, the authors investigated the capability of an acidic thiourea solution and silicon-organic polymers (PSTM-3c, PSTM-3T) as ion-exchange resins to recover of gold from gold-bearing ore concentrates. Firstly, elemental gold present in flotation concentrates was dissolved by leaching with a solution of nitric acid and thiourea under the optimized conditions. The best result on gold thiourea leaching was obtained under a nitric acid concentration of 2 N, thiourea concentration of 2 %, and oxidant (Fe2(SO4)3) concentration of 3 %, solid:liquid ratio (S:L) of 1:20, leaching time of 6 hours at 20 °C with a gold recovery of 93.7 % for a gold flotation (unroasted) concentrate. For the roasted gold concentrate, the dissolution of gold was 94.8% under the optimized leaching condition as nitric acid concentration of 0.5 N, thiourea concentration of 2 %, and the oxidant concentration of 1 %, S:L ratio of 1:10, leaching time of 4 hours at 50 °C. Secondly, a series of sorption tests was carried out on a pregnant leach solution containing gold complex Au[S=C(NH2)2]2+ using silicon-organic polymers (PSTM-3c and PSTM-3T), respectively. The effects of solution pH, adsorption time and temperature in the sorption process are also studied. As the results, the PSTM-3c and PSTM-3T polymers were adsorbed about 94.4 % and 95.1 % gold from the pregnant leach solutions under the optimum sorption conditions, respectively. It was found that the both PSTM-3c and PSTM-3T polymers were effective for the recovery of gold from the pregnant leach solution of thiourea. Adsorption activity of the PSTM-3c and PSTM-3T polymers was confirmed by new peaks near 1700 cm-1 in the FT-IR spectrum of the gold-adsorbed polymers, respectively.

Jan 1, 2014

By A. N. Zagorodnyaya, Ye. G. Bochevskaya, E. A. Sargelova, Z. S. Abisheva, A. S. Sharipova

"In Kazakhstan, there is a unique sulphide copper deposit, in the ores containing the natural isotope of osmium-187 (more than 90 %). In the pyrometallurgical processing of concentrates for the target metal, osmium is mainly sublimated, with wet cleaning of metallurgical gases (dust and gas mixture) 40 % of it together with rhenium passes into washing solutions (wash acid). On the basis of this acid, the production of ammonium perrhenate was organized at the enterprise of the RSE ""Zhezkazganredmet"" and for the first time in the world practice - the isotope of osmium-187. However, the degree of its recovery from solutions does not exceed 8 % of the amount supplied with the charge or 25 % of the amount that was received for extraction. But the bulk of it (~ 75 %) remains in the raffinate, discharged to sewage treatment plants (wastewater). The studies presented in this work are aimed at solving the problem of osmium isotope-187 extracting from wastewater, which are a potential source of increasing metal production in Kazakhstan. The aim of this work is the development and scientific justification of osmium deposition regimes from wastewater using such reagents as thiosulfate and sodium sulphide. The influence of various physicochemical factors on the precipitation of the osmium was studied and optimal conditions for its maximum transition to sediment were chosen. An original method for obtaining osmium concentrate in the presence of sodium thiosulfate with the addition of potassium iodide from a new type of wastewater - man-made ammonia solutions has been developed. These solutions were combined mother liquors of solid-phase stripping operations and dissolution of pulp of crude ammonium perrhenate. On the basis of the obtained results, a settling technology for extraction of the osmium from man-made ammonia rhenium-containing solutions was introduced at RSE ""Zhezkazganredmet"". It should be noted that the degree of extraction of osmium, depending on its concentration in solutions entering on the settlement, and taking into account the addition of sulfuric acid, will vary from 60 to 90 %. The recovery of osmium during the test period was 58 %."

Jan 1, 2018

By Aubrey Mainza, Malcolm S. Powell

"A hydrocyclone with two vortex finders, named the three-product cyclone, has been successfully tested in the Platinum industry for dealing with the dense chromite found in UG2 ores. This dense component preferentially reports to the cyclone underflow, resulting in an over-ground fine chromite component in the final product. The dense media effect caused by a high chromite concentration in the cyclone feed produces a coarsening of the cyclone overflow, which results in loss of recovery through over-size material in the float feed. The fine barren particles of chromite that report to the overflow are recovered through entrainment in the flotation process, resulting in detrimental contamination of the slag produced from the concentrate.With the three-product cyclone a middlings product has been extracted that has a higher concentration of fine chromite. This volumetric stream flow represents a small percentage of the total cyclone feed and it is thus possible to treat it separately via fine screening to remove the fine chromite from the system and recover coarse silica."

Jan 1, 2003

By Alexander E. Sobolev

The kinetics of oxidative dissolution of lead sulfide in solutions of nitric acid and sodium hypochlorite was studied using the rotating disk method and the factor experiment design. The dependences of the PbS dissolution rate on concentration of oxidant (HNO3 or NaOCl), temperature, disk rotation frequency, and duration of interaction were determined. The adequate kinetic models allowing calculating the specific dissolution rate at any combination of values of the influencing factors were obtained. As a result of the complex analysis of kinetic parameters, the modes of the each process proceeding were established, their macromechanisms were determined, and the limiting stages of the oxidative dissolution processes were revealed. The dissolution kinetics of lead sulfide in solutions of nitric acid was found to have several regimes. At HNO3 concentrations below 0.5 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled. It is caused by low oxidative activity of HNO3 and considerable diffusional diffuculties at this acid concentration range. At the nitric acid concentrations more than 0.5 mol/L and less than 6.0 mol/L, the process was found to be kinetically controlled. The limiting stage of the interaction is the surface chemical reaction. The observed relatively high order of the dissolution rate with respect to the concentration of HNO3 was explained by the autocatalytic action of the acid reduction products. At nitric acid concentrations exceeding 6 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled, and the dissolution rate sharply decreased that was explained by a decrease in the solubility of reaction products. When lead sulfide is dissolved in sodium hypochlorite solutions, at first time the amount of PbS transferred into solution remains close to zero. Gradually, as time goes, this amount begins to increase sharply. The dissolution rate rises and reaches the maximum value, further remaining constant. At the steady-state regime, the dissolution rate is independent of the duration of interaction and disk rotation frequency. The process was found to be kinetically controlled. The limiting stage is likely to be chemical reaction on the surface of solid lead sulfide. The obtained kinetic characteristics enlarge the database on hydrochemical oxidation kinetics of sulfides and can be used for the elaboration of the recommendations for the effective comprehensive exploitation of lead-bearing ores and concentrates. Keywords: lead sulfide, nitric acid, sodium hypochlorite, hydrochemical oxidation, dissolution kinetics

Sep 1, 2012

By G. S. Hansford, G. E. Searby

The rate of bioleaching of pyrite at 70ºC by a thermophilic archaeal culture was measured as a function of the solution redox potential by the staged addition of pyrite to a batch system. The results were compared to the rate of ferrous iron oxidation over the same potential range to determine the applicability of the multi-sub-process leaching mechanism developed for mesophilic bioleach systems.

Jan 1, 2003

By R. Els Ellis

Enhanced granulation of UASB granules was tested on pilot scale with two different test reactors (about 5 litres capacity each). Sludge from a local sewage works was used, with peach cannery effluent as carbon source. Cyclic motion of the reactor contents, and a daily replenishment of feed material create the necessary stress conditions for enhanced growth. Sizable granules, bigger than 0.5 mm, were produced within 20 days. Of the two reactors tested, the reactor equipped with a horizontal agitation shaft proved more effective.

Jan 1, 2003