Search Documents

By John W. M. Lambert

This paper describes the execution and the results of a new method to seal off leaks in water retaining constructions. The new method, called BioSealing is based on activating the bacteries, present in soil and groundwater. The method was tested under field conditions in 2004 and applied at the HSL aqueduct of the 'Ringvaart Haarlemmermeer' in 2005.

Jan 1, 2006

By Bengt H. Fellenius

"ABSTRACTAn example from a guidelines document for the Eurocode is discussed that addresses design for geotechnical strength of piled foundations in settling soil, generating drag force and downdrag. A modified example of geotechnical response is then analyzed in a failure mode, Ultimate Limit States (ULS), and stationary long-term state, Serviceable Limit States (SLS). It is shown that the Eurocode principles, when applied to correctly determined forces, results in an irrational and costly design. The results of the analysis of the modified example are applied to eight different codes pertaining to piled foundations from USA, Canada, Europe, and other countries. Several of the codes require that the drag force be included as a load in a ULS design, which an absurd and costly requirement, in some codes, in one case made even worse by combining drag force with live load. A major weakness of almost all codes is their minimal treatment and sometimes total absence of aspects of settlement of piled foundation. In contrast, my main argument is that design for capacity, whether in working stress approach, or by LFRD or ULS approaches, is not always safe unless a thorough settlement analysis shows that the design also meets the requirements of the SLS.1. INTRODUCTIONFirst, there were analysis, design, and construction establishing a State-of-Practice, SOP. Then, came codes and specifications summarizing the SOP, as interpreted by a committee. When the state-of-art, SOA, was not understood by that SOP-interpreting committee, the codes and specifications are uneconomical and, sometimes, also unsafe.The paper first presents an example quoted from two commentaries on the Eurocode 7 on design for geotechnical strength by the Eurocode (1997). The example is then modified to a more realistic case and analyzed in failure mode (ultimate limit states, ULS) and in the context of settlement (serviceability limit states, SLS). The analysis results are then applied to eight codes addressing piled foundation design and changes necessary for the referenced codes and specifications to be closer to the SOA are identified."

Jan 1, 2014

By Y. Z. Xu

This paper presents a new dynamic method called Resonant Pile Test (HPT) for evaluating bearing capacity of pile. The basic conception of RPT is given in brief and the measuring system is also introduced. In addition, the influences of the magnitude of exciting force and of the mass of pile cap on test results are discussed. Finally, comparisons between values of bearing capacity given by RPT and by static load tests for a variety of pile types are listed.

Jan 1, 2010

By Boleslaw A. Klosinski

Drilling of a pier hole is accompanied with stress releasing in the surrounding soil and often with loosening of soil at the pier base. In effect the drilled piers are more deformable than driven piles of comparable dimension. The bearing performance of a pier may be considerably improved by properly executed base grouting. Various techniques of base grouting are used; many of them were described by Bruce (1986). The grouting devices are often placed within the pier. Alternatively the soil at or under the base is treated by cement or chemical grout. Preloading of the base subsoil by use of a special grouting cell is considered as the most effective way. Treatment of the ground below pier base with cement or chemical grout may be also useful. It may be performed immediately after the pier construction or during service, as a measure for increasing the pier capacity.

Jan 1, 1995

By James P. Hambleton, Anastasia Nally

This work focuses on the numerical simulation of multi-plate anchor systems (e.g., helical anchors) in sand subjected to vertical loading. In assessing the stiffness and capacity of these multi-plate anchor systems, full awareness of the abilities and limitations of the various analysis methods must be understood. This work first summarizes studies completed by others and then goes on to assess the failure mechanisms of multi-plate anchors in sand and the influence of (1) plate width-to-depth ratio, (2) number of plates, and (3) relative positioning of plates. The analysis makes use of (1) conventional limit analysis, (2) so-called modified limit analysis that employs reduced strength parameters to account for the influence of soil dilatancy, and (3) the displacement-based finite element method, which considers elastic as well as plastic deformation leading to failure. The work critically reflects on limitations in the current analysis methods for helical ground anchors. INTRODUCTION Helical anchors are a relatively low cost foundation type, typically consisting of a steel rod and single or multiple plate attachments. In recent decades, they have seen rapid growth, and as outlined by Merifield and Sloan (2006) and Hambleton et al. (2014). Design techniques for helical anchors have previously been predominately empirical, as much of the past research in this field is experimentally based. It is common practice for helical anchors to be modeled as horizontally oriented plate anchors in both numerical and experimental analysis. This work focuses on analysis based on the finite element method, including so-called finite element limit analysis and the conventional displacement-based finite element method, with some comparisons made to experimental studies. Numerical simulation of anchor pull-out capacity in cohesionless soils is stunted by the many difficulties faced when using numerical analysis with cohesionless soils. Additional variations can be seen when comparing the serviceability based load capacities to the ultimate load. In this work, both the force-displacement response (stiffness) and the ultimate anchor capacity are assessed, with more focus on the latter. This work focuses only on analysis techniques for multi-plate anchors with vertical loading in cohesionless soils. Many studies have been completed in this area, some of which assume a rectangular plate in a plain strain model (Rowe & Davis, 1982; Merifield & Sloan, 2006; Cerfontaine et al., 2019). Whereas others use axisymmetric conditions (Baker and Kondner, 1966; Saeedy, 1987; Murray & Geddes, 1987; Ghaly & Hanna, 1994; Sakai & Tanaka, 1998; Merifield et al., 2006;) and minimal studies considered both axisymmetric and plane strain in the one study (Vesic, 1971; Tagaya et al., 1988; Murray & Geddes, 1987; Sarac, 1989).

Jan 1, 2019

By Chu E. Ho, Paul Napoli

A new waterfront park was developed on Long Island in close proximity to the East River and Newtown Creek. The existing ground consisted of fill over soft organic clay, medium dense silty sand, glacial till and schist bedrock. The ground was initially raised to preload the underlying soft soils to stabilize the ground in preparation for site development. The ground was subsequently cut down to temporary grades for installation of foundation piles for the overlook structures and construction of reinforced concrete cantilever retaining walls forming pathways located adjacent to the water bodies. The retaining walls were located in two rows at different elevations along the sides of a steep embankment. Where the pathways converge, some of the walls were too close to each other, and were redesigned as a combined U-wall with a common base slab. The individual retaining walls were designed for adequate bearing, sliding and overturning resistance. Ground anchors were installed to enhance global stability of the retaining walls. This paper presents the design considerations for the retaining walls for various loading conditions, and evaluation of the trial and proof tests for the anchors. INTRODUCTION The New York City Master Plan included the transformation of an approximately 30-acre parcel of land in Long Island City, Queens, New York from a former manufacturing zone into a residential, commercial and recreational zone for middle-income community. The site was located at Hunters Point South along the eastern shoreline of the East River and Newtown Creek (Figure 1). The development included low to high- rise residential buildings, a public school, and retail structures. Open spaces were provided along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community-related activities. Waterfront structures included small park buildings, walkways and viewing platforms. The shoreline was surrounded by revetments as part of the flood mitigation strategy. The project involved extensive site re-grading and several retaining walls were constructed. The earthwork volume amounted to approximately 47,000 cubic yard of imported fill and 93,000 cubic yard of cut. The exposed height of the retaining walls ranged from 3 to 15 feet. This paper focuses on the design and construction of the retaining walls for the project.

Jan 1, 2019

By Van E. Komurka

This paper presents a cost comparison of the driven pile foundations for two large Wisconsin Department of Transportation (?WisDOT?) projects in Milwaukee, Wisconsin: the Marquette Interchange South Leg, and the Canal Street Viaduct. The projects? geology is fairly similar, but their methods/approaches to pile foundation design and installation differ. Although the Marquette Interchange South Leg had deeper poor soils, its pile design was more-cost-effective than the Canal Street Viaduct?s. Potential reasons for cost differences between the projects are identified, and the effect of the different design and construction approaches on economics is discussed.

Jan 1, 2009

By Damian R. Siebert

Risk-reduction measures implemented during the design and construction of a 21-story pile-supported building adjacent to a below-grade 100-year-old sewer structure were keys to a successful foundation system. Avoiding damage to the existing sewer structure during construction activities and the future ability to access the structure post-construction were the main concerns for the utility owner. Clear communication and a deliberate design process between all parties ? utility owner, building owner, structural engineer, geotechnical engineer, architect, and contractor ? were integral to the project?s success. This collaborative process helped all parties to understand the risks, both real and perceived, and to develop mitigation measures to reduce the risks. Bringing together all parties to engage in dialogue and encouraging open communication throughout the project were paramount to its success. By implementing the joint design plan, using mutually-acceptable construction techniques, and careful monitoring, the building foundation was successfully installed and all parties? risks were averted.

Jan 1, 2011

By Issa S. Oweis

Limestone is a sedimentary rock composed primarily of calcite (calcium carbonate). In the presence of an aqueous solution of carbon dioxide (carbonic acid) bicarbonate radicals (2HCO3)- are produced that are highly soluble. The same type of reactions occur in terrains where dolomite (calcium magnesium bicarbonate) reacts with carbonic acid to produce highly soluble bicarbonates (4HCO3)-. The source of carbon dioxide is the small content in rainfall but to a large extent from the organics in the soil. The solution activity depends on many factors including the content of carbon in the rock, acidity of soil water, groundwater velocity and other factors. The resulting features are referred to in literature as sinkholes, solution channels, caves, karstic topography, and cavernous limestone. The presence of solution features affect the shafts in several ways: (a) the shaft resistance is affected by voids along the shaft, (b) concreting of the shaft should consider the presence of voids along the shaft, and (c) the shaft base may be in close proximity to a solution feature that may cause future collapse under structural loads. Methods to mitigate such effects include verification of rock to below the base (vertically and laterally). Cavities are stable by virtue of arching in the rock. Under the action of end bearing from a shaft, the arch may collapse depending on its proximity to the base of the shaft and the strength of the rock. This paper focuses on this issue. Finite Element analyses are conducted to relate shaft end load and bearing area that will produce failure based on given rock properties, size and location of cavity. Failure is defined as settlement of the base equivalent to 5% of shaft socket diameter. The software Plaxis is used for analysis. The rock is considered as c-f material derived based on Hoek-Brown failure criteria (2002 edition) that is based on Geological Strength Index (GSI).

Jan 1, 2009

By H. Boghosian

This paper presents the design and construction of a deep basement in a steeply sloping site in glacial till in Glasgow city centre. Existing foundations, adjacent structures and services, in tandem with asymmetric loading, presented particular challenges in the planning, execution and design of the project. The construction methods and temporary works, analysis by the Finite Element method and monitoring carried out are all described.

Jan 1, 2006

By JO Choi

Jet-grouting method is a useful technique to reinforce foundations on relatively soft or vulnerable soil layers such as fractured zone and stratum with cavities. Although jet-grouting has been widely applied to various field works, a reliable design standard has not been established yet. A number of model tests were performed to investigate end bearing behaviors of piles reinforced by jet-grouting. It was concluded that end bearing capacity was increased in proportion to uniaxial compressive strength of grout column. Based on the test results, the design criteria for the end bearing capacity were suggested.

Jan 1, 2006

By Brian H. Greene

The U.S. Army Corps of Engineers, Pittsburgh District, is in the final phases of modernizing the locks and dams on the Monongahela River. One facet of this modernization is to replace the existing Locks 4 located on the Monongahela River approximately 40 river miles upstream from Pittsburgh, Pennsylvania. The existing locks consist of a 56-foot x 720-foot main chamber and a riverside 56-foot x 360-foot auxiliary chamber built in the 1930s. Two new lock chambers, each 84-foot wide by 720-foot long, will be constructed at the location of existing Locks 4 and will be named Charleroi Locks. The purpose of the new project is to facilitate navigation on the lower Monongahela River. Pittsburgh is currently the second largest inland waterway port in the nation, and the new locks will be an important component of the navigational infrastructure. The existing lock walls are of mass concrete construction and are founded on wooden timber piles driven to rock through alluvial sands and gravels. The new lock walls were designed to be supported by approximately 300 reinforced concrete drilled shafts, varying in diameter from 4 to 6 feet. To handle axial loads, the drilled shafts were designed for end bearing, with some skin friction. The tips of the shafts will be founded within competent rock. Since the walls will undergo lateral loads, the drilled shaft design also had to consider this loading condition. Some of the drilled shafts will be installed within coffer boxes, which will incorporate a tremie concrete seal down to top of rock. Complicating the design even further was the fact that some portions of the new walls will be supported by shafts that extend some 9 feet above top of rock through alluvial soils, producing a cantilever effect. The first phase of the new lock construction was initiated in the summer of 2005 with a contract awarded to replace the river wall. This required shutting down the existing riverside lock chamber and diverting all river traffic to the longer existing land chamber. The foundation of the new river wall will use 144 drilled shafts. To optimize the design embedment of drilled shafts in rock for the river wall, an exploratory drilling program was conducted by the contractor in July and August, 2005. Based on the quality of the sedimentary bedrock, the shafts will be embedded in rock from 31 to 38 feet. To achieve adequate end bearing resistance, the tips of each shaft will extend through predominantly claystones into a more competent siltstone unit for a minimum embedment of one foot. The contractor also performed an exploratory pile driving program to aid in the construction of the drilled shaft casing and the cut off walls that will encapsulate the river wall. Two demonstration drilled shafts located outside the footprint of the new river wall, will be constructed prior to the drilling of any production shafts. The demonstration drilled shafts will verify that the contractor is able to meet the design criteria and quality requirements of the contract. The river wall contract is currently underway and is scheduled to be completed in 2010.

Jan 1, 2006

By Jose L. Garcia

The following document aims to cover all issues concerning the three main methods employed for the in-situ survey of concrete pile integrity. Within it are described both sonic coring and low-strain tests and the frequency and time domain analysis of their results, which are the most advanced techniques currently in use in Spain. The survey techniques described were developed and began worldwide deployment in the 1960s, but it was not until the 1980s that they saw large scale implementation in Spain, largely thanks to the miniaturisation of electronics and computer equipment that made them easier to use on-site. Sonic coring, echo and frequency-response testing or mechanical impedance tests are spreading further every day. However, there appears to be a need for standardisation of the testing methods, as well as their implementation, interpretation and the presentation of results. The goal of these Spanish recommendations is to serve as a guideline for test standards and to provide examples for a correct and commonly agreed interpretation of test results, as well as settling any differences in the evaluation of defects detected in foundation works.

Jan 1, 2006

By H. L. Jessberger

In recent years piled raft foundations of multi-storey buildings on weak soils have generated much interest and discussion. By taking account of the effects of each component of the system - the pile group and the raft - it is possible to reduce the settlements and inclinations of the system and to have an expedient load distribution on the piles and the raft. Thus the structural design of the foundation can be optimised.

Jan 1, 1991

By Carlos Lam, Joram M. Amir, Erez I. Amir

"Abstract The modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic loading tests on piles. This value is commonly assumed to be constant with depth though it may not be true for deep bored piles due to the chosen casting method and/or selfweight consolidation. To provide evidence to support this proposition, the results of compressive strength tests on core samples taken from four different studies have been presented. The results show a marked increase in the strength and stiffness values with depth. The results of crosshole ultrasonic tests conducted at another site also confirm the same pattern. It is therefore recommended that before load testing a pile the distribution of the E values along the pile axis should be investigated. This will ensure the use of a realistic elastic modulus value and hence the correct interpretation of thedistribution between the shaft and end resistances.IntroductionThe modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic load tests on piles. Multiplying E by the strain measured by either strain gauges (e.g. ASTM D4945) or tell-tales (e.g. Geffen and Amir, 1971) gives the stresses acting at a given pile section. Typically, in the absence of better information, the value of E is derived from laboratory tests on concrete cubes or cylinder specimens taken on site and is assumed to be constant along the pile. While this may be correct for pre-fabricated concrete piles that are cast in horizontal molds, it may not be true for cast-in-place piles that are produced in the vertical position.There are at least two factors that may contribute to the change in concrete properties with depth in a bored pile. First, the casting methods may be by free fall in dry holes (e.g. Kiefer and Baker, 1994) or by using a tremie tube if support fluids are used. In the former case, the earlier batches reach the bottom of the pile bore at a higher velocity and are thus compacted under higher energy. Second, regardless of the casting method, the fresh concrete in the pile bore will always consolidate at least partially under its own self weight. The materials in the lower parts of the pile will therefore experience a higher consolidating pressure. This can reduce the pore volume and the water content in the wet concrete, thus changing the properties of the hardened concrete. Recent research by Justs et al. (2011) has shown that even a relatively small pressure can have a significant positive effect on concrete properties such as compressive strength and stiffness. However, the possible change of concrete properties with depth is commonly ignored by foundation engineers in the current design practice."

Jan 1, 2014

By Dhanaji S. Chavan, Thallak G. Sitharam

"It is well known that sites comprising of saturated loose sand undergoes large deformations, due to liquefaction, during seismic shaking. To cope with this, different mitigation techniques such as vibroflotation, deep dynamic compaction, compaction grouting, deep soil mixing etc. have been used in practice. However, as all these methods are costly, a new mitigation technique is required. Air injection has emerged as a new mitigation technique in which air is injected into the saturated loose sand. The introduced air makes the pore fluid mixture compressible and results into decrease in the generation of excess pore water pressure during seismic shaking. This paper reviews the laboratory and field studies performed to investigate the effect of air injection on liquefaction resistance. In addition to this, previous research in the direction of desaturation has evolved different techniques to generate gas in saturated sand. These techniques have also been discussed in the present paper. All the field and laboratory studies have shown that even a slight decrease in the degree of saturation increases the liquefaction resistance significantly.Keywords: desaturation, air injection, liquefaction resistance, pore pressureINTRODUCTIONEarthquake events in the past, caused liquefaction of loose saturated sands at many sites in the world. The consequence of liquefaction varied from small deformations to catastrophic failures such as flow slides, lateral spreading, sand boiling etc. (Kramer, 1996). To reduce the liquefaction potential of such soils, different mitigation techniques have emerged across the world. Some of the most widely used mitigation techniques are vibroflotation, deep dynamic compaction, compaction grouting and deep soil mixing (Idriss and Boulanger, 2008).Yoshimi et al. (1989) found that the liquefaction resistance of partially saturated sand is significantly higher than that of saturated loose sand. Further, Pietruszczak et al. (2003) proposed desaturation of the saturated loose sand as a new liquefaction mitigation technique. It is observed that the liquefaction resistance of sandy soil is enhanced significantly owing to the desaturation caused during construction of sand compaction piles (Ishihara et al. 2003). Over past few years research is being carried out on desaturation of sandy soil and its liquefaction resistance ( Ishihara et al. 2003; Okamura and Soga 2006; Yegian et al. 2006; Yegian et al. 2007; Takemura et al. 2009; Eseller-bayat et al. 2013; He et al. 2013; Marasini and Okamura 2015; Zeybek and Madabhushi 2016). As a result of this, different techniques of desaturation have also emerged. Different studies conducted in this direction and their outcome has been discussed in the section to follow."

Jan 1, 2017

By M. B. Wechsler

An analysis is developed for determining the maximum loading, as well as the potential uplift of the piles on bridge pier foundations. There are considered piers supported on two through seven rows of piles, and related to two simply supported collinear superstructures of any structural material. The study leads to different types of influence lines for various load combinations. For load combinations containing vertical loads only, the related influence lines are similar to those as for the bending moments of a virtual span covering the two actual spans, as well as the gap between the two superstructures; and, in this case, the heavier loads should be positioned in the vicinity of the pier. While, in the case when vertical loads are acting together with hori­zontal forces, the related influence lines will indicate where the heavier live loads should be positioned. And they will also indicate on which portions of the spans the live load should be avoided.

Jan 1, 1989

By T. Soejima

In recent years, there has been a tendency in the field of foundation piling works to utilize piles of greater bearing capacity in order to meet increasing height and weight of modern building as a means of saving of piling cost. To satisfy these requirement, a new technique for large diameter bell bottom cast-in-place piling has been developed utilizing multi-head reverse circulation drilling system.

Jan 1, 2010

By D. M. Milovic

On the basis of relatively large number of field load tests of piles, the determination of the ultimate bearing capacity have been studied. Using the load settlement curves and the results of the cone or standard penetrat­ion tests, the ultimate bearing capacity was determined by Van der Veen?s, Mazurkiewicz?s and bilinear approximation method. Also, the evaluation of the modulus of deformation and the unit skin friction has been discussed.

Jan 1, 2010

By Y. Duraisamy

This paper presents the compressibility of tropical peat reinforced with cylindrical cement column. When a cement column installed vertically in peat, its compressibility was reduced because of the hardened skeleton matrix formed by cement particles bonding with adjacent soil particles in the presence of pore water. The effects of diameter, number of columns and cement proportions in cement columns on the compressibility have been investigated in this study. The results indicated that compressibility index Cc and Ca decreased with the increase in diameter of the cement column. Specimens with 45 mm and 60 mm diameter of cement column were cured for 28 days, after which they were subjected to Rowe Cell Consolidation test. Based on the results obtained, it shows that cement columns can successfully reduce the compressibility of tropical peat.

Jan 1, 2007