Search Documents

By Jeffrey A. Schaefer

The Olmsted Locks and Dam project is located on the Ohio River approximately 16.5 miles upstream of its confluence with the Mississippi River. It consists of twin 1200 ft. locks with floating and fixed approach walls, five 110 ft. wide tainter gate bays, a 1400 ft. wide navigable pass boat operated wicket gate section, and a 400-ft. section of fixed weir (Fig. 1). The project will have a total cost over 1.0 billion dollars, and as such is one of the largest civil works project underway in the Corps of Engineers.

Jan 1, 2001

By Thomas M. Gurtowski

This paper presents a summary of allowable bearing pressures and skin friction values that have been used to design drilled pier foundations for support of high-rise structures in downtown Seattle, Washington. These design parameters are based upon a review of geotechnical reports and records of more than 20 building projects. The following pages present a description of the soils encountered at these sites including foundation bearings soils, and design bearing and friction values. The accumulated data is summarized in Table 1, and the locations of the buildings are shown in Figure 1. A detailed description of the construction of two belled drilled piers are presented illustrating typical methods and procedures used in downtown Seattle. The two cases are from the Washington State Convention and Trade Center (WSC&TC). SEATTLE AREA SOILS The Puget Sound area was subjected to several major glaciations during the Pleistocene Epoch. Glacial ice originated in the cordilleran and coastal mountains and the Vancouver Range of British Columbia. The maximum southward advance of ice reached the area about halfway between Olympia and Centralia. As a result of these glaciations, the Puget Lowland was filled to significant depths by glacial and non-glacial sediments during the Pleistocene.

Jan 1, 1990

By Daryl W. Wurster

The Liberty Bridge in Greenville, South Carolina is a curved, cable-stayed, pedestrian bridge with primary support provided by two towers. The bridge is part of the Falls Park redevelopment. The bridge was originally designed to be supported on drilled piers. Alternately, the bridge was supported on a combination of micropiles and anchor piles because of difficult access and subsurface conditions. The use of micropiles and anchor piles led to improved construction scheduling and reduced costs. Micropiles were used to resist compressive loads. Anchor piles were used to resist tensile forces and to eliminate excessive settlement of pile caps into underlying fill during pre-stressing. This paper describes the site history, bridge construction, site and subsurface conditions encountered, and the decisions that led to support of the bridge using micropiles and anchor piles and foundation construction.

Jan 1, 2006

By Ali Ameli

Design loads are limited for piles relying upon toe stresses in rock due to uncertainty about the rock quality over the whole pile diameter because of rock mass properties or construction effects. The paper discusses the use of video images to evaluate rock quality at the bottom of piles socketed into graniodorite bedrock in a steel pipe pile project. Skillful interpretation was required to assess the 3D properties of the rock from video images. It is necessary to observe the rock mass characteristics near the project site for better perception of the rock features from the images. Video image interpretation skills were established by the evaluation of the cores drilled under the socket base and the results of pile loading tests. Correlations were found between rock appearance in the images and the rock socket drilling records. Rock socket acceptance criteria were developed through monitoring the drilling operations for the specific site procedures. Video images then served as one of the quality-assurance tools together with probing and pile loading test. Lessons and methods learned from video inspection in this project could be used to evaluate rock quality in similar cases.

Jan 1, 2006

By Ray Schmahl

The Glenwood Canyon is a 13 mile long river gorge formed by the Colorado River approximately 2 miles East of Glenwood Springs, Colorado and approximately 150 miles West of Denver Colorado, (See Drawing #1). The canyon walls rise some 800 feet from the river elevation on either side of the river. The South-side river bank is occupied by the Denver and Rio Grande Western Railroad. The Northside is currently occupied by completed sections of Interstate 70 and US Highway 6. The railroad was built in the late 1800's and a hydroelectric power generating station was built in about the center of the canyon in the early 1900's. The Highway 6 platform was completed in the 1930's. The design and alignment for Interstate 70 thru Glenwood Canyon began in the early 1970's. The Highway thru Glenwood Canyon was designated a scenic Highway by the United States Congress, thereby allowing certain deviations from standard Interstate requirements. Environmentalists objections to the construction of Interstate Highways thru Glenwood Canyon resulted in especially careful design to avoid adverse environmental impacts. As a result, in many areas the new Highways will have restored the canyon to its more native configuration than what was the case in the building of the US 6 Highway platform.

Jan 1, 1990

By Aminul Islam, Vinay M. Kumar

"About 100 Hectares of land reclamation over the very soft to soft marine clay at Uran Creek in Maharashtra is planned. The depth of marine clay varies from 10m to 24m as observed from the geotechnical investigation. The marine clay was treated with Pre-fabricated Vertical Drains (PVD’s) installed from the elevation of +5.5mCD (chart Datum) and preload/placement of surcharge. A Settlement of soft soil mud under the reclamation was monitored using magnetic extensometer (M) and ground settlement maker (S2). These instruments are installed after constructing working platform at around +5.5m CD. Based on the field instrumentation data, the consolidation parameters were adjusted to match the theoretical and actual settlement plot. The author called this approach as “Back analysis method”. The objective of this paper is to present a case study of instrumented preloading treatment for a thick marine clay deposit. The degree of consolidation in clay strata was determined from magnetic extensometer and ground settlement marker data. Authors also determined degree of consolidation as Asaoka method, Hyperbolic method and Back analysis method and compared the results.INTRODUCTIONExpansion of Container terminal with port buildings, rail container depot, roads and utility buildings at Jawaharlal Nehru Port Trust (JNPT) is planned over a reclaimed land of 100 hectares. Uran creek predominately consists of the estuarine deposit of very soft to soft marine clay. They are characterized by low shear strength, very low bearing capacity and exhibit large settlement when subjected to loading. The additional load causes the significant magnitude of consolidation settlement over a considerable period of time. Thus for development projects on top of soft soil, the postconstruction settlement would be of primary concern.To accelerate the consolidation pre-fabricated vertical drains (PVD) were used. Pre-loading procedure was adopted to minimize the post construction total and differential settlements. PVD’s were installed at 1.0m and 1.2m c/c triangular pattern. Locally available borrow material is used as a reclamation material. The reclamation material has been placed over the existing sea bed level by land based method/end tipping method and created the working platform. The level of working platform is decided based on the tide data and it has been selected such that work should be affected during highest high water level. The PVD has been installed from the working platform and subsequently all the field instruments have been installed from the same level. Five different types of field instruments are installed to monitor ground improvement works."

Jan 1, 2017

By William Babcock

Augered, Cast-In-Place (ACIP) piles can be an economical, reliable, versatile foundation system. They have also been a part of projects that were behind schedule and the subject of lawsuits. The ACIP pile is a specialty system that is more workmanship dependent than most deep foundation systems and is especially vulnerable to the problems and abuse of poor specifications and contract language. Many of the original specifications were based on grouting methods, and numerous misconceptions have followed the method. The Deep Foundations Institute (DFI) has been the leader in debunking the mystique that has hovered over the method and attempted to standardize the industry through publication of the manuals describing the method and how it should be inspected. DFI should be applauded for taking the lead and producing a reference document that can be used to educate the specification writers, designers, inspectors, and owners. It must be must appreciated that there have been other organizations that would not acknowledge ACIP piles as a legitimate member of the deep foundation family. Some consultants and designers have gone to the extreme of making it policy to not recommend the method for use. This presentation is one practitioner's view of the causes of problems as they can be traced back to the contractual conditions. It is intended to provide a broader and different perspective than those provided by the technical specialists. It does not necessarily reflect the position of the DFI or any of the organizations associated with the ACIP pile industry. It is intended to further the spirit of partnering on every ACIP pile project, to further the acceptance and promote the use of this unique system, for the benefit of all the parties. It should be recognized, however, that all of the participants can and do play a role in getting a project into trouble. My view is that projects that get into trouble usually have an early flaw that leads the project to the edge, and the project participants blindly follow the original mistake right over the cliff like lemmings. This instinctive reaction may be a survival tactic by going along with the group, because any one party that departs from the program or shows a position of weakness is a candidate for sacrifice.

Jan 1, 1997

By Paul J. Sabatini, Yazen A. Khasawneh

"A Demag CC1800 crawler crane was partially erected on crane mats adjacent to a seawall when settlements near a corner of the crane mat area were observed to be slightly larger than previously assessed. A ground improvement program including installation of dry soil cement mix (DSM) piers was implemented to improve soil bearing capacity. Due to near-surface obstructions, only 75 percent of the DSM piers were installed to the design depth. Because of the partial installation of the DSM piers, an evaluation of the crane pad stability and the effect of the crane loading on the stability of an adjacent 10-ft high concrete seawall, which was believed to have limited (if any) reserve capacity, was required. A two-dimensional finite element model was developed to evaluate the responses of the partially improved ground and the sea wall to the loads imposed by the crane. Geotechnical site investigation and laboratory testing programs were performed to better define the subsurface conditions near the area where settlements occurred and to provide the required mechanical parameters for the soil constitutive model. Analysis results indicate that total and differential settlements of the crane pad and the increase in load on the seawall were tolerable provided limited excavation and replacement of weak dredged soils outside the DSM area would be implemented.INTRODUCTION & BACKGROUNDA Demag CC1800 was erected on 8 ft × 16 ft crane lattice mats at about 12 ft from an existing seawall. Approximately 3.5 in. of subsidence was observed at one corner of the crane mats, while the crane was partially erected and stationary. The approximate location of the crane mats with respect to the existing seawall when the subsidence occurred is shown on Fig. 1.The seawall consists of a reinforced concrete wall connected by reinforced concrete bents to a composite section of sheet pile wall; the total depth of the seawall is about 29 ft. The bents are spaced at about 20’4” and supported by five piles at each bent location. The composite sheet pile consists of concrete and a sheet pile section with a reinforced concrete wale section. The retaining wall is about 10 ft in height and is supported at three levels. The first support level comprises a 2-½” diameter steel rod near the top of the wall spaced at 40’8” the second and third level supports comprise 1-½” diameter steel rods spaced at about 5’6”. The second level support is inclined at about 10 degrees below horizontal and the third level support is oriented horizontally through the wall footing. A schematic of the seawall section is shown on Fig. 2.A geotechnical site investigation was implemented soon after the subsidence was observed. The program included advancing four borings to a depth ranging from 16 ft below ground surface (bgs) to about 30 ft bgs. In general, the investigation showed sandy material (likely fill that was used behind the retaining wall) from the ground surface in two borings located immediately behind the retaining wall. The other two borings furthest from the retaining wall showed very soft to soft clay (possibly dredged material) from the ground surface to a depth of about 10 ft bgs. Based on this information, the ultimate bearing capacity of the subsoils was estimated to range from 1,200 to 2,000 pounds per square feet (psf). From the anticipated crane loading (weight of the crane and loading lifts), a minimum allowable bearing capacity of about 1,500 psf would be required for safe operation. To achieve the required bearing capacity a ground improvement program was selected and implemented."

Jan 1, 2017

By Ke Yang

"Drilled shafts are typically used to support structures subjected to large moments at the shaft head. The large moment can produce push and pull forces on the two sides of a drilled shaft. Consequently, the applied moment is partially resisted by the push-pull moment resistance induced from the vertical side shears. This type of push-pull resistance has not been fully recognized in most design and analysis methods. In this paper, a 30 finite element model for a drilled shaft subjected to lateral load and moment is presented and is validated against two field lateral load tests. Based on the 30 finite element model, a parametric study is carried out. It shows that the push-pull moment can resist 18-35% of the applied moment. The parametric study also shows that the push-pull resistance varies linearly with loading eccentricity when the eccentricity is less than the shaft embedment length. A method to estimate the push-pull resistance is proposed based on the results of the parametric study. Then, a new method for lateral capacity prediction is proposed to account for the push-pull resistance. The base shear resistance is significant for short drilled shafts; therefore it is also included in the proposed method. A case study on four lateral load field tests illustrates that the new method could improve the accuracy of lateral capacity prediction when compared with the traditional Broms method.INTRODUCTIONDrilled shafts are typically used to support a variety of structures subjected to large moments. Sound walls, highway signs, traffic signals, high-rise buildings, electrical transmission towers, and bridge piers are examples of cases where lateral loads with large eccentricity would result in high overturning moments on foundations.Current analysis methods for capacity predictions (Broms, 1964a and 1964b; Brinch Hansen, 1961) or deflection predictions (Reese, et al. 197 4) of laterally loaded drilled shafts are based on the lateral resistance of soils and rocks. However, O'Neill pointed out that moments can be partially resisted through the push-pull resistance provided by the vertical side shears due to the rotation of the pile (Reese, 1997)."

Jan 1, 2005

By Mark R. Svinkin

This paper deals with application of the wave equation analysis to determine capacities of piles driven in saturated sandy soils. It shows that pile capacity in sandy soils changes with time after the completion of pile driving and depends on the ground water elevation. In saturated sandy soils the setup coefficient ranges between upper and lower curves represented by power functions. For a reliable prediction of pile capacity wave equation input should be adjusted with soil damping. Back calculation of soil damping from known pile capacity performed for five tested piles shows that skin damping coefficient changes with time in the same manner as the pile capacity and can be represented by the power functions for considered damping models.

Jan 1, 1995

By J. Nakayama

Down-the-hole hammer is commonly recognized as the most powerful drilling equipment for weathered to fresh rock formation including boulders. However, its drilling diameter is restricted by reasons of difficulty to actualize large diameter drillhead and to ensure discharging means of cuttings. Cuttings are usually removed by flushing i.e. uprising return air after compressed air actuates hammer, but in case of large diameter drilling, as the clearance between drill rod and surrounding wall of hole become fairly large, necessary up-hole air velocity to transport cuttings can not be maintained. In case of marine or underwater drilling or high groundwater table, orthodox down-the-hole hammer is obstructed its operation by water. This single head hammer drill combined large diameter drillhead with reverse circulation of drilling fluid enables large diameter drilling extending to 1.5 m, i.e. actualized large diameter mechanical drillhead incorporated with ensured cuttings removal means enabled this range of drilling. This paper introduces its features and actual applications to large diameter bored pile drilling for varied sorts of rocks in maritime construction projects.

Jan 1, 1996

By Amaneh E. Kenarsari

Among the different sources of uncertainty in pile bearing capacity prediction including inherent heterogeneity, measurement and model uncertainties, the inherent heterogeneity of soil properties is of particular interest and is considered in this study. Cone tip resistance data are utilized to calculate pile bearing capacity by considering vertical soil variability. In this regard, cone tip resistance component of CPT data is assumed as a random parameter. Realizations of this parameter are achieved with the aid of local average subdivisions and random field theories. Monte Carlo simulation is used to generate different realizations of CPT or CPT-u data. Pile bearing capacity was then calculated by the use of direct method. Pile bearing capacity are predicted for a project in south of Iran using this method and probability density function for the total bearing capacity of pile is plotted. Coefficient of variation of 33% for ultimate bearing capacity shows the variability of bearing capacity due to variation of soil strength in depth. Cumulative probability chart for the ultimate bearing capacity are plotted as an efficient tool for estimating ultimate bearing capacity of piles with different desired confidence levels for vertically variable soil strength properties. Significant difference between mean value of pile bearing capacity (18 MN) and limit with 95% confidence level (8 MN) emphasizes the importance of considering soil variability.

Jan 1, 2011

By Kirk A. Mcintosh

Augered, cast-in-place (ACIP) piles have been utilized in the United States for a wide range of projects since the 1950's. Due to the cast-in-place nature of the installation method (and lack of a driving criteria); however, ACIP piles have not been readily accepted by some practicing geotechnical and structural engineers. Since ACIP piles were initially developed, the installation equipment and techniques have been improved and refined and the number of experienced contractors has significantly increased. Over the past 10 to 15 years, the pile type has experienced significant growth in the United States (particularly in Florida) because engineers have become more knowledgeable and comfortable with its use. The Miami area, in particular, has experienced considerable growth in the utilization of ACIP piles primarily due to their usage on the $1 billion Miami Metrorail System project in the early 1980s. The economic advantages over other deep foundation types, coupled with some unique installation advantages, have shown that ACIP piles can be a viable foundation alternative on many projects. Even though ACIP piles have gained respect in the private sector, the pile type has generally not been readily accepted by government transportation agencies. The reluctance to readily accept this foundation type stems primarily from the quality assurance aspect of cast-in-place pile construction. Additionally, there has not been much research activity on this foundation type, technical papers, formal associations (other than the DFI), or a concerted effort to standardize the industry. This paper serves to discuss the state of practice for ACIP pile installation in the state of Florida.

Jan 1, 1997

By James J. Tansey

A Deep Foundations Institute meeting with the University of Michigan at Ann Arbor in March of 1984 featured legal rights under Differing Site Conditions. A workshop conducted by the authors and Gerard Ittig, Esq. added to the value of the symposium. This paper will be of interest to your attorneys in any subsurface disputes.

Jan 1, 1985

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Sep 8, 2021

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Oct 1, 2021

By L. P. Weber

During the years 1983-1987, a research programme, jointly performed by the steel producers ARBED, British Steel Corporation, Peine-Salzgitter, Unimetal, and co-sponsored by the European Community for Steel and Coal (ECSC), has been carried out on steel H-piles of different shapes. The initial aim of the testing programme has been the improvement of bearing capacity, both in sandy and clayey soils. At two test sites, standard H-beams are compared to H-piles with different types of laggings or to H-piles grouted both under low and high pressure. In this paper and in view of the open european market in 1992, the H-pile capacities and their corresponding allowable loads, determined from codes, recommendations and computation procedures in use in Belgium/Luxembourg (B/L), France (F), Federal Republic of Germany (G), and the United Kingdom (UK) as well as their evaluation from dynamic CAPWAP and Case methods are compared to the static capacities measured in-situ. In addition, procedures for estimating the load/movement behaviour of H-piles from CPT, pressuremeter, and CAPWAP are compared to the measured curves.

Jan 1, 1991

By J. -L. Briaud

This presentation shows the results of laboratory and field tests to date for the NCHRP project entitled "Downdrag on Bitumen-coated Piles". This project required to test a variety of bitumens in the laboratory to determine their properties and then to establish a field testing program to verify the bitumens effectiveness. Figure 1 shows an organizational chart that gives an overview of the agencies involved in the project. The first part describes the laboratory testing program in which bitumen samples of various types were obtained from a variety of manufacturers. Initially, classification tests were performed to verify the manufacturers' specifications. Additional tests were then developed and performed to determine the bitumens behavior under the various conditions that they may be exposed to in the field. The test results were analyzed and their usefulness for design purposes were determined. The test results are presented in either graphical or tabular form. The second part describes the field testing program which was designed to test the effectiveness of various bitumens under a wide range of soil, temperature, and construction conditions. The first site was in Edmonton, Alberta, Canada, where a construction project was to take place in the winter of 1989-90. This was ideal for the cold temperature extreme that was needed. The soil conditions were conducive to downdrag problems: an embankment placed over soft clay underlain by dense sand resulting in end-bearing piles. The other site was in New Orleans, Louisiana. The part of the project involving this downdrag study was to be carried out in the summer of 1990. The hot summer temperatures and extremely soft soil conditions (resulting in friction piles) gave the other extreme needed for this study. Each site is discussed in

Jan 1, 1991

By Colin Curtis

In recent years, Manchester Airport has undergone expansion including the construction of a second runway, a new terminal building (Terminal 3) and extensions to the existing Terminal 1. Manchester is Britains third largest airport and ranked 20th in the world for international traffic. Arup (Manchester) was engaged as consulting engineer in a multi-disciplinary role for the terminal works. Part of this was a geotechnical commission including site investigation and pile design followed by supervision. This paper reviews the piling for the old, new and terminal extensions. In total, five pile types have been utilised over the years. The original 1950's Terminal 1 was founded on driven cast in situ piles, with a later 1970's extension utilising rotary augured piles. The recent piling comprised continuous flight auger piles (CFA), driven steel tube and tripod bored; the latter in areas of restricted access or low headroom. The ground conditions are Made Ground over thin Alluvial and Glacial drift, in turn, over a generally weak to moderately weak gypsiferous mudstone. All the piles were socketed into the mudstone. In terms of the new CFA piles, quality control using the instrumentation monitoring was problematical, but a substantial static load and integrity test programme resolved pile performance. Part of the work is matching new pile performance with previously installed piles and the continued use of older piles with new loads. Research provided some data on the older piles, including some static load test data, which enabled back analyses of their design and likely behaviour. Differences in design methods, installation techniques and pile behaviour based on load tests will be discussed.

Jan 1, 2001

By Ali Porbaha

The use of soil nailing technology as a cost effective alternative for excavation support and slope stabilization has substantially increased in the United States during the last decade. For example, in the past thirteen years, more than 185,800 square meters of soil nail walls have been constructed in California alone. The conventional soil nail systems pose difficulties when ground conditions are subject to caving, for instance for silty sand (sugar sand) or cobbles and boulders. The construction industry has developed self drilling hollow bar systems (or pressure injected bored, IBO) that combine both drilling, placing and grouting in a single operation as a solution to speed up construction. While the system is extensively used for temporary applications, nevertheless, some concerns, particularly about corrosion, has limited the use of this technology as a permanent system in North America. This study presents several issues related to self drilling soil nail systems, the results of a field investigation and a summary of the research project.

Jan 1, 2006