Search Documents

By David K. Crapps

The drilled shaft load tests at Port Orange were part of a demonstration project sponsored by the Federal Highway Administration (FHWA) and the Florida Department of Transportation (FDOT). Three load tests were conducted. Test 1 was a conventional test with the test shaft loaded from the top. Test 2 included an Osterberg load cell at the tip and a conventional load test from the top. Test 3 used an Osterberg load cell at the tip of a production drilled shaft. All three test shafts were socketed into limerock and were carried to failure. This paper describes the test program and presents a summary of the test results. Figure 1 presents some photographs of the load test setups and Figure 2 shows the location of the drilled shaft load tests. SITE CONDITIONS The Port Orange Bridge is located on US A1A over the Intercoastal Waterway in Port Orange, Florida (south of Daytona Beach). The new bridge will provide four lanes of traffic with a 65 foot vertical clearance for Intercoastal Waterway traffic. The channel and flanking piers will be supported by 54" drilled shafts socketed into the rock. The bridge is being constructed in two phases. The southern half will be completed first, the old bridge removed and then the northern half will be constructed. The first phase is scheduled to be opened to traffic in October 1989. Each of the four piers near the channel will be supported by 12 drilled shafts with 6 shafts per pier being constructed in each phase.

Jan 1, 1989

By Alberto Carmona Rosell, Sri Ram Ramankutty

"The installation of Bored Piles and Diaphragm Wall under slurry using tremie raises quality concerns on the integrity of concrete. It is vital to understand the effects on concrete integrity during concrete pouring process. This paper intends to unveil to what extent the compressive strength of the concrete pour is affected in contact with drilling fluid still. Another important angle of analysis proves whether the inclusion of solids particles of un-hydrated fluid could have impact on the concrete compressive strength. The testing comparing the response of concrete compressive strength when drilling fluid is included into the concrete mix altering the water/cement ratio by 5%, 20% and 30%. Comparative results are analysed between two different hydrated slurries namely sodium activated Bentonite and 3rd generation synthetic polymer.1. INTRODUCTIONSoil stabilization is the base for a successful deep foundation execution. The G3 System Slurry developed by Ground Engineering Operations (GEO), with its third generation polymer, namely PolyMud®, is an innovative and unique alternative to the mineral based slurries for soil stabilization, enhancing the quality and integrity of the underground foundation structures. It optimises the production rate of work progress and cost as well. At the same time, PolyMud® slurry is proven to be environmentally friendly.Guaranteeing the maximum quality of the foundation elements according to the initial design is one of the most important objectives and a concern for the foundations contractors. In order to fulfil the project expectations in this aspect, any incident that could compromise the designed concrete integrity and capacity must be avoided.GEO, has carry out its own research regarding effects on the concrete compression results if drilling fluid intermixes with fresh concrete while pouring. To shed light in this regard, GEO, in collaboration with CML (Concrete Materials Laboratory) Sdn. Bhd., carried out empiric tests that analyse this particular event from different perspectives, bringing up the corresponding results that will be studied and commented in this article."

Jan 1, 2015

By James Warner

Investigations of the sinkhole indicated that the loose, disturbed ground was completely encircled by dense competent core. This confinement substantially increased the effectiveness of the compaction grouting compared to what might have been expected at a "greenfield" site. However, the 8 ft diameter circle shown in the plan view was only the surface expression of the sinkhole proper and the deep, loosened ground actually extended to a larger diameter of about 20 ft. The planned spacing of the grout holes was based on the finite element simulations using a target void ratio of less than 0.3 throughout the compacted ground within a 5 ft radius of the grout injection point. Because of the strong confinement effect, the layout of grout holes included one central primary hole surrounded by six secondary holes at a triangular spacing of about 5 ft. Since the disturbed ground was considered a confined cylinder, it was anticipated that the primary hole would perform the majority of work and the secondary holes would act as check holes, with progressively lesser grout takes as the loose ground densified.

Feb 10, 2003

By Stefan Dahlin

The laboratory tests indicated low permeability but as I said, as a rule, the permeability in the field has been found to be higher. A high permeability has also been found when doing back calculations of rates of settlements in different cases. But as I also said, there's a need for further studies in this area.

Feb 10, 2003

By Juhyung Lee

Numerical analyses were performed to analyze the behavior of two different type of suction piles (mono type and group type) under various soil layer conditions (uniform silty clay layer, uniform silty sand layer, and two-layer deposit consisting of clay and sand layers) and lateral loading locations (top, middle, and bottom of the suction pile). According to the results, mono suction pile shows maximum resistance when load is applied on its middle, regardless of the soil layer conditions, while group suction piles varies significantly according to the allowance on head rotation. When head rotation is allowed, the behavior of group type piles become similar to the behavior of mono suction pile. Whereas, when rotation is prevented, resistance is maximized when load is applied on the top head. Moreover, group suction piles show higher efficiency regardless of the ground condition and geological stratum. For further advances, concrete block on the top of group suction piles are suggested as an effective alternative method to prevent partial rotation and maximize ground resistance for group suction piles.

By Ping Yang, Tian-bin Li, Min-hui Wu

"The process of filtrate loss of low solid-phase drilling fluid at different content of polyanionic cellulose is investigated by the standard filtration test. The test results showed that when time of filtration is same, the filtrate volume decreases linearly with the increase of content of polyanionic cellulose. When content of polyanionic cellulose is same, the velocity of filter loss decreases nonlinearly with the increase of time and the velocity of filter loss will reach a stable value. The filtrate volume in 7 to 8 minutes can reach half of the total filtrate volume. At the same time, the velocity of filter loss of drilling fluid decreases nonlinearly with the increase of viscosity. When apparent viscosity is between 3.5~4.15 mPa.s, decrease speed of velocity of filter loss is quick. The results are helpful for characteristics evaluation of filtrate loss of drilling fluid and control of filtrate loss.IntroductionDuring the process of drilling, water of drilling fluid can leakage into stratum, the water can result in instability and collapse of borehole wall. At the same time, the original ratio of drilling fluid will change. The density of drilling fluid will increase, the performance of the drilling fluid will change. Controlling amount of filtration is important to drill successfully. The additives of controlling filtrate loss are mainly two types, particle materials and polymer materials. High-molecular polymer is a kind of high-molecular material, has the adsorption effect, high polymer protection, can improve the advantages of slurry viscosity (Xu,2004 and Dehghanpour,2001). Some scholars carried out some study on the polymer material fluid loss agent in recent years, these study mainly focused on CMC, HEC, MHEC, CMHEC, starch and its derivatives(Zhang,2005 and Chevron,2009).About PAC (polyanionic cellulose) as drilling mud additives, a few of scholars carried out some relevant work. Plank (1992) applied PAC into ordinary freshwater drilling fluid and analyzed temperature stability of freshwater drilling fluid. Bennion (2000) applied PAC into drilling fluid and analyzed effect of polyanionic cellulose on strata inhibitory. Huang (2011) analyzed effect of PAC on properties of the high-density water-based drilling fluid. Mahto (2004) applied PAC into fresh water and salt-water drilling fluid and analyzed effect of PAC on rheological properties of the drilling fluid. Wang (2008) applied PAC into alkaline drilling fluid to study various performance of drilling fluid. PAC is a renewable resource and has good application prospect (Ankara, 2005). So it is very important to understand the effect of PAC on filtration process of drilling fluid.The test was conducted by changing the content of the PAC in drilling fluid. The object of this paper is to understand effect of polyanionic cellulose on filtration process of the low solid-phase drilling fluid."

Jan 1, 2017

By Gianni O. Chieruzzi

A 400 MW, gas-fed power plant on floating piles and piled raft foundations was constructed in the Province of Moskovskaya, Russia in 2008. The subsurface is characterized by fill underlain by loose to medium dense alluvial deposits, with peat and clay interbeds, a stiff to hard, highly plastic, silty clay stratum of glacial origin, and a stratum of very dense, varved interbeds of sand and silt. More than 800, drilled concrete piles were constructed at the site. The pile length ranged from 15 to 23 meters below existing surface grade, and the pile diameter ranged from 0.9 to 1 meter. Initial analyses by others predicted total power plant settlements of 3 to 4 cm when subjected to the permanent loading conditions. Under a peer review process for the equipment supplier, subsurface investigation and testing were performed to verify the consolidation parameters used for foundation design of the power plant foundation. The parameters obtained in this investigation were used in the 3-D finite-element model ELPLA as inputs for the settlement analysis of the turbine building and power island. The ELPA analyses predicted settlements on the order of 7 cm over a period of 30 years. The actual settlements after two years of monitoring were compared against the model predictions. The rate of settlement and the recompression index were both underestimated in our model. The measured settlements have enabled us to calibrate both of these model parameters so that the model better matches the data.

By Alireza Ayoubian, Douglas S. Roy, Gianni O. Chieruzzi

"A 400 MW, gas-fed power plant on floating piles and piled raft foundations was constructed in the Province of Moskovskaya, Russia in 2008. The subsurface is characterized by fill underlain by loose to medium dense alluvial deposits, with peat and clay interbeds, a stiff to hard, highly plastic, silty clay stratum of glacial origin, and a stratum of very dense, varved interbeds of sand and silt.More than 800, drilled concrete piles were constructed at the site. The pile length ranged from 15 to 23 meters below existing surface grade, and the pile diameter ranged from 0.9 to 1 meter.Initial analyses by others predicted total power plant settlements of 3 to 4 cm when subjected to the permanent loading conditions. Under a peer review process for the equipment supplier, subsurface investigation and testing were performed to verify the consolidation parameters used for foundation design of the power plant foundation. The parameters obtained in this investigation were used in the 3-D finite-element model ELPLA as inputs for the settlement analysis of the turbine building and power island. The ELPA analyses predicted settlements on the order of 7 cm over a period of 30 years. The actual settlements after two years of monitoring were compared against the model predictions. The rate of settlement and the recompression index were both underestimated in our model. The measured settlements have enabled us to calibrate both of these model parameters so that the model better matches the data.IntroductionA 400 MW, gas-fed power plant was constructed near Moscow in the Province of Moskovskaya in Russia.Figure 1 shows the general arrangement of the main structures, and the geometry of the piles supporting those structures."

Jan 1, 2017

By Kiyotaka Ohno, Nobushige Yasuoka, Yosuke Hioki

"The diameter of improved columns adopted by the original DJM Method had been 1000 mm, however, in order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter expanded to 1300 mm was developed between 1998 and 2001 and has been widely applied since then. From the first application of EX-DJM in January 2002 for a first construction project, the total volume of improved soil has reached 325,000 m3 in 17 projects up to September 2014. Because of the advantages of the EX-DJM such as reduction of construction costs and periods leading to reduction in the number of improved columns, adoption of this method is expected to increase in the future. This paper describes the advantages of the EX-DJM, its construction results and case examples including those applied to restoration projects after the Great East Japan Earthquake, 2011.1. BACKGROUND OF DEVELOPMENTThe Dry Jet Mixing (DJM) Method is a soil stabilization method in which a powdery or granular binder is pneumatically fed into and mixed with soft soil to induce chemical reactions that stabilize and strengthen the soil. It was developed by government - private collaboration in Japan between 1977 and 1979. Up to March 2014, the total volume of soil improved by DJM method reached 33,500,000 m3. The initial diameter of improved columns of the original DJM Method was 1000 mm. In order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter 1300 mm was developed between 1998 and 2001.2. ADVANTAGES OF EX-DJMThe construction equipment for the EX-DJM consists of two major parts, which are DJM machine and binder plant are shown in Fig. 1.The construction machine is of double mixing-shaft type with its column diameter expanded to 1200mm or 1300mm. In association with the increase in the column diameter, the binder feeder has also increased its discharge rate by approximately 1.69 times. Same as the increase rate of the area of original diameter 1000mm to diameter 1300mm are shown in Fig. 4."

Jan 1, 2015

By Racquel Nottingham, Marc Mastrantuono

Micropiles often provide a favourable solution for many deep foundation problems especially when significant site constraints such as confined construction sites or vibration limitations have been identified. Often the durability of buried steel elements are heavily scrutinized in order to effectively determine the rates of corrosion and methods to reduce this while still maintaining the structural integrity of the engineered solution. Practices such as sacrificial corrosion loss and the introduction of plastic sheaths have become the go-to methods of corrosion protection. Since the introduction of the micropile, other solutions have been developed, namely protection with an adequate grout encapsulation. This paper will explore corrosion protection of micropiles and the guidelines provided in the published codes and norms. Since few codes define the exact way to verify the durability of these micropiled structures, the existing data is presented and the analysis of grout encapsulation as an effective corrosion protection method is evaluated.

Oct 1, 2022

By Sepideh Damavandinejad Monfared

In recognition of the practicality of using inclined micropiles as elements for foundation support to resist static and seismic loading conditions, specifically in retrofitting projects, this study presents an investigation into the beh avior of an inclined micropile subjected to simultaneous lateral load and bending moment. Three-dimensional numerical simulations are performed using the finite element method to assess the influence of micropile geometrical parameters such as angle of inclination, length, and diameter on the response of micropile-soil system. The Mohr-Coulomb failure criterion is used to define the behavior of soil and stabilized soil around micropile materials and the micropile, constructed of concrete and steel, is assumed to be elastic. The interaction between soil and micropile is taken into account by defining interaction elements covering both tangential and normal behavior. The study is carried out using nonlinear FEM analyses. The results of these simulations indicate that negative micropiles, in which slip surface deflects downward, have higher lateral load capacity than positive micropiles with slip surface deflecting upward. The conducted research also shows that increasing the diameter and the length of micropile increases the lateral load capacity. Increasing micropile diameter is more effective in increasing lateral load capacity. A relationship is developed from statistical regression analysis of the finite element modeling computations to estimate the lateral displacement of a micropile inclined at an angle of 30o in silty sands.

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"The use of steel screw piles has greatly increased in recent years because of the advancement in the installation mechanism and its performance under compressive, uplift and lateral loads. In a steel pile system, the strength of pile material limits the end bearing resistance of the pile due to strong subsurface conditions. The installation mechanism of screw pile can reduce the end bearing resistance due to the torque and axial force. However, if the installation mechanism does not reduce the bearing resistance of the pile, another important factor that can reduce its performance is the strength of the helix/wing plate. In this study, the effect of wing plate deformation on the performance of single helix/wing plate pile bearing resistance investigated. A model ground was used to investigate the effect of wing plate deformation. Dry Toyoura sand was used as a ground material and was compacted to denser states of 80% and 92%. The shaft and wing plate material of the pile was the same to actual piles that are used nowadays in Japan. A series of load tests were performed with different wing plate diameters and thicknesses. It was observed that deflection in the wing plate reduces the bearing resistance of the pile. The increase in the thickness of the wing plate was seen to restore the reduced pile resistance due to deflection. It was also observed from the experimental results that the ratio of wing plate diameter to shaft diameter (Dw/Ds) greatly affects the deformation of wing plates, which ultimately affects the end bearing resistance of the pile. The results obtained in this research suggest that the outstand length (Lw) of wing plate should be less than 5.6 times the thickness of wing plate for piles having a large Dw/Ds ratio under strong ground conditions.INTRODUCTIONThe first use of screw pile was almost 180 years ago by Alexander Mitchell. He patented his invention in 1833 with the name “Screw Pile”, and used it for ship moorings. The use of screw piles has since been adopted in various areas such as lighthouses, fencing for agriculture and marine structures. The use of screw piles in civil works started in 1985, after the invention of the hydraulic torque motor, as it eases the installation process. Nowadays, screw piles are used in the foundation of transmission towers, elevators, buildings and many other civil structures.Screw pile has an edge over other steel pile systems due to its high bearing, uplift and lateral resistance. The end bearing resistance of screw pile depends on installation, strength of subsurface material and the pile material. The screw pile is installed by applying torque and axial force. The pile torsional strength should be more than the applied torque and axial force to avoid deformation before reaching the final depth."

Jan 1, 2015

By Hennie F. T. Barnard, Theodore E. B. Vorster

Where geotechnical designs are governed by settlement requirements, soil and rock moduli are important parameters for design. This paper reports on a method that was used to utilize dynamic modulus measurements in the field toward pile settlement designs for the proposed Square Kilometer Array (SKA) Project to be located near Carnarvon, South Africa. The project will comprise of over 3000 No. movement sensitive satellite dish structures. The method described in the paper utilizes strain-related modulus degradation across the complete ground profile, starting from measurements of peak particle velocity (and inference to dynamic modulus at small strain) as measured using Continuous Surface Wave (CSW) testing at individual dish positions. This is required due to the very small allowable foundation rotation of 5 arc seconds under the dishes’ operational conditions. The strategy of analysis was to conduct an iterative process starting from the measured small strain modulus profile of the ground. The likely maximum pile force for a specific piled foundation option was estimated and a single pile finite element analysis was performed using Plaxis 2D (Version 2010) to estimate the expected ground strain developing along the length of the pile. By assuming the shape of the shear modulus degradation curve with increasing shear strain, the iteration process then converged on a likely degraded modulus profile associated with the single pile and maximum load assumed. This process enabled identifying the pile cap size, pile configuration, pile sizes and pile lengths that would meet the operational movement limits. The chosen pile group configuration was then analyzed using the Repute 1.5 pile group analysis software. The design process and typical results are discussed in this paper.

Jan 1, 2017

By Alexandre Alex) J. Bredikhin

"DISCLAIMER: the statements presented herein are those of the author and do not necessarily represent the views of US DoD or its Components.ABSTRACTProgress on the $750M lock project on the Monongahela River was derailed by discovery of large anomalies in the 6.5-7-ft dia. drilled shafts of the new river wall foundation. The anomalies were located 45 to 50’ below the top of the wall at the critical shaft-to-wall interface, and ranged in thickness from several inches to 2-plus feet. A Specialty team, comprised of representatives from the contractor, the Government, and structural design consultants, was formed to evaluate the extent of the problem and the impact on the new lock wall. With no standard method in place, the Government took the lead to develop acceptance criteria for the repairs while the contractor took the lead to identify the repair means and methods. The Government developed a detailed Quality Control plan to capture and document all of the repair data and to approve each shaft repair in a timely manner. This paper provides an overview of the anomalies encountered and the need for repairs; discusses the details of the repair plan; and provides details on the unique quality control measures employed to verify the repairs. By developing and adhering to a detailed quality control plan, the structural integrity of all of the shafts was successfully restored.INTRODUCTIONThe new Charleroi Locks Project is currently under construction by the U.S. Army Corps of Engineers (USACE) in Pittsburgh, Pennsylvania. In the region, the Corps of Engineers is modernizing the series of locks and dams on the Monongahela River. One facet of this modernization is replacement of the existing Locks #4 (aka Charleroi Locks) located upstream of Pittsburgh, Pennsylvania with new and larger capacity locks. The relative location of the project is shown on Fig. 1. The original construction of twin locks (56’x720’ & 56’x360’) and the fixed-crest dam was completed in 1932, with lock walls supported on timber pile foundations. The fixed crest dam was replaced with a gated dam in the 1960’s. The existing lock is undersized and in poor condition and thus needs to be replaced. The project requires the construction of the new river chamber adjacent to the existing land chamber which must remain operational to navigation throughout the construction. In order to accomplish this, the lock walls need to be constructed in the wet. The river wall was constructed using two construction methods referred to on the project as “cofferbox” and “non-cofferbox” construction."

Jan 1, 2017

By Hiren J. Shah

Across much of New York City, the geology of glacially deposited soils follows a common sequence. Outwash sands generally overlie varved silts and clays, which lie above a basal till deposit underlain by the bedrock. Pile foundations at projects with such typical stratigraphy generally develop their axial capacities by extending below the fine-grained deposits into the till or the bedrock. Contrastingly, at a project site on the Brooklyn waterfront, high capacity piles were efficiently and economically installed by driving them into the relatively shallow glacial drift and till deposits which lay above thick fine-grained compressible glacial lake deposits. An unusual aspect about the foundation design at the Brooklyn project site is that, relatively short and high capacity piles were driven into the shallow glacial drift and till deposits, overlying the thick fine-grained glacial lake deposits. In order for this unusual foundation scheme to be feasible and economical, the piles needed to achieve their driving criteria in the upper strata. Consolidation settlements in the lower stiff and over-consolidated glacial lake deposits below the pile tips had to be relatively small. The paper discusses the unusual stratigraphy in this area of Brooklyn in greater detail with geologic profiles and engineering characteristics of the glacial strata. It also discusses the design aspects of the pile foundations, settlement estimates, a pile drive test program during design, results of the static load test program during construction, and production pile installation results.

Jan 1, 2008

By Frank Haehnig, Harald Krenn, Harm-Christoph Claassen

"The Wadi Dayqah Dam Water Supply Scheme represents one of the most important projects implemented by the Sultanate of Oman to ensure sustainability of water resources. The principal components of the project comprise two dams to impound the Wadi Dayqah, to store and supply drinking water to the local area and to Muscat, the capital city of the Sultanate.The Main Dam with a central spillway is a RCC Gravity Dam with a maximum height above foundations of 75m, crest length 400m; the Saddle Dam is a rockfill dam with central clay core, max height above foundations is 49m and crest length 360m. During construction of the Saddle Dam a key trench was excavated to 10m depth and filled with compacted clay connected to the central core of the embankment. Grouting utilizing cement grout was performed as a single line grout curtain prior to each filling operations. Both Dams are founded on soft Siltstone, Claystone, Sandstone and inter-bedded harder limestone.After construction of the Saddle Dam, once water was in the reservoir it became evident in early 2010 that some seepage was occurring apparently from the right abutment. This seepage became more marked when the reservoir first filled to discharge over the spillway in June 2010. In order to reduce the seepage, additional sealing works by drilling and grouting of a three row curtain up to 80 meter target depth were initiated to supplement the existing single row curtain. Part of this project for the sealing works has also been to drill additional investigation holes to provide more information and confirm extend of the additional sealing works and its limits.Züblin Ground Engineering was awarded the Additional Sealing Works Contract. Whilst Equipment was on Site, the opportunity was taken to carry out drilling and grouting on the Left Abutment of the Main Dam to reduce seepage through that abutment and to install additional standpipe piezometer for future monitoring of seepage patterns.Work on this Contract started on site in January 2013 and was substantially completed in January 2015.At the time of Tender Züblin Ground Engineering propose and Alternative Design in the form of a Secant PileCut-Off Wall, 85m long to a depth of 40m with additional drilling and grouting below the foot of the cut-off which was then included in the contractual scope."

Jan 1, 2016

By Kessi E. Zicko, Eric A. Hackenberg, Paul J. Lewis

"Following snow melt and spring rains in 2011, a landslide measuring approximately 600 feet long and 300 feet in slope length occurred within the southbound roadway embankment of a heavily travelled 2-lane divided highway in North Central Pennsylvania. Driven steel piles were designed to stabilize the embankment slope. Factors affecting the selected stabilization technique included an adjacent reservoir, wetlands, the length and depth of the failure plane, extent of glacial lake deposits, excess pore pressures in the foundation soils, and an area of archaeological interest. Field reconnaissance and subsurface explorations including borings, instrumentation, geophysics, and laboratory testing indicated that glacial lake deposits were present in the toe region of the embankment. Instrumentation proved key in measuring excess pore pressures and in locating the failure plane, and geophysics was utilized to estimate the extent of the soft glacial lake deposits and to estimate pile lengths. The existing condition of the embankment was modeled in computer slope stability analyses, which were also used to help assign soil parameters. Significant costs were associated with constructing a berm due to the impacts on adjacent site features. Therefore, multiple rows of driven steel H-piles were designed for installation along the toe of the embankment. The design lateral load in the piles was based on slope stability analyses, and the pile size and number of piles were based on lateral pile computations with modified p-y curves to account for installing piles in an active landslide. The relationship between the factors of safety from slope stability and the LRFD pile design was significant in determining pile loads for lateral analyses.INTRODUCTIONA landslide developed along the lower portion of the southbound embankment of State Route 15 in Tioga County, Pennsylvania. The road passes through a steep valley and is located along the southern extent of the Tioga Reservoir. Although no damage to S.R. 15 was attributed to this landslide, the close proximity of the slide to the road posed a concern for the long-term stability of this section of roadway.This paper presents a summary of the site history; the subsurface conditions based on borings, instrumentation, a geophysical survey, and laboratory testing; slope stability analyses including alternatives assessment; and the pile design.SITE HISTORYS.R. 15 was originally located in the valley along the Tioga River and traversed through the towns of Tioga and Mansfield. Although the reason is unknown, it is interesting to note that Old S.R. 15 curved away from the river in the area of the landslide. In the mid 1970’s, S.R. 15 was relocated to the eastern hillside prior to construction of the Tioga-Hammond Reservoir by the U.S. Army Corps of Engineers. The relocated highway was constructed in stages. Two lanes of relocated S.R. 15 were initially constructed to carry one lane of northbound and one lane of southbound traffic. At this same time, the majority of the fill was placed for two future lanes immediately to the west, which would eventually allow for two lanes in each direction. The two eastern lanes would then carry northbound traffic after completion of the two southbound lanes to the west."

Jan 1, 2015

By Han Jie

The results of full scale plate load tests on stone columns on soft clay in coastal areas are presented in this paper. Four load tests were made, two of which were performed on the ground treated with stone columns, one on an isolated stone column and the last one on the untreated ground. For a given stress range, the settlement of the rigid plate, the stress concentration factor, and the excess pore water pressure were measured. It is found that the distribution of vertical stress beneath the rigid plate supported by the composite ground of stone columns is very different in shape from the one by the untreated ground, that the stress concentration factor has a relation with the stress level and time, that the stone columns increase the bearing capacity up to by 2 times, and that the ground stabilized by stone columns is of great advantage to keep the foundation stable.

Jan 1, 1991

By Jeffery L. Ottesen

Early construction delays can jeopardize timely completion of subsequent work. As an early construction activity, and due to many unforeseen issues, deep foundation work inherently bears great potential for impacting the critical path of a planned construction schedule. This article describes two construction projects where delays related to deep foundation work forced the Contractor to consider various schedule recovery alternatives to mitigate those delays. Specifically, deep foundations on Vancouver BC's Millennium SkyTrain light rail extension and on a Mill Facility in the United States are discussed. This article cites examples of permitting delays, alleged design changes, differing subsurface conditions and changed construction methodology, the effect each problem had on the project, the mitigation means implemented by the Contractor to minimize adverse impacts of the problem, and Lessons Learned for each scenario.

Jan 1, 2002

By Martina Balic

Dynamic properties of the drilled shaft foundations supporting Doremus Avenue Bridge were determined by forced vibration testing. The main objectives of the substructure testing at Doremus Avenue Bridge were: (1) site evaluation with respect to the dynamic soil properties, and, (2) shaft evaluation for the purpose of definition of their dynamic stiffness. The site characterization entailed crosshole testing for the purpose of evaluation of the shear modulus profile. The drilled shaft impedance evaluation was done through forced excitation using an electromagnetic shaker. The responses of the tested shaft, as well as the response of adjacent shafts, were measured for the purpose of evaluation of the shaft interaction. To gain a better insight into the shaft dynamics, one of the shafts was instrumented with five triaxial geophones distributed along the full length of the shaft. The scope and results of the site characterization, shaft impedance and shaft interaction evaluation are presented.

Jan 1, 2004