Search Documents

By Md. Nafiul Haque, Murad Y. Abu-Farsakh, Chris Nickel

"This paper presents the results from a pile load testing program for a bridge construction project in Louisiana. The testing includes two 54-inch open-ended spun cast concrete cylinder piles (OECP), one 30-inch open-ended steel pile (OESP), and two (30-inch and 16-inch) square prestressed concrete (PSC) piles driven at two locations with very similar soil conditions. All the test piles were instrumented with vibrating wire strain gauges to measure the load distribution along the length of the test piles and the skin friction and the end bearing were derived from strain gauge measurements. High strain dynamic load tests (HSDLT) were performed on all test piles at different times after pile installations to quantify the amount of setup with time. Static load tests were also performed on the PSC and open-ended steel piles. Due to expected large pile capacities, the statnamic test method was used on the two open-ended cylinder piles. The pile capacities of these piles were evaluated using various CPT methods (such as Schmertmann, De Ruiter and Beringen, LCPC, COFS methods). The result showed that all the methods can estimate the skin friction with good accuracy; but not the end-bearing capacity. Setup was observed for all the piles, which was mainly attributed to increase in skin frictions. The setup rate parameters “A” [The “A” parameter is defined as the rate of increase of pile capacity ratio (Rt/Rto) per log cycle of elapsed time] were back-calculated for all the test piles and the values were between 0.31 and 0.41.INTRODUCTIONDue to greater efficiency (capacity to weight ratio) of the pipe piles, open-ended piles are a viable option to solid piles. However, the behavior of open-ended piles is more complicated compared to the close-ended piles owing to possible formation of “soil plug” inside the open-ended pile. Many researchers have analyzed the behavior of both types of piles for different purposes; however, very few studies in the literature offer the side-by-side comparison of the close-ended and open-ended piles."

Jan 1, 2017

By Charles M. Wilk

"Mass stabilization involves mixing binding agents into marginal or contaminated soil to improve the subject material’s physical and/or chemical properties. This paper concentrates on the principles of soil mixing and benefits and application to new and existing rail right-of-way. Successfully applied in Scandinavia and other European countries, the soil mixing is now being applied in right of way in the northern latitudes of the U.S. and Canada. These regions have significant areas of “peaty” soils that can complicate construction and maintenance of rail and structure foundations. Mass stabilization can be used to improve the bearing strength of these soft soils for subsequent construction of railroads, pipelines, roads, and buildings. In civil engineering, the technology is often used to improve the construction properties such as bearing strength, of a marginal soil. In environmental engineering, stabilization is remediation treatment technology that protects human health and the environment by immobilizing hazardous constituents within the treated material. . The treatment is conducted while the subject material remains in-place (insitu). Mass Stabilization is often used to accomplish both civil and environmental purposes on the same project effectively addressing marginal soil while eliminating the expense of soil removal and replacement. This paper presents the principles of mass stabilization technology, implementation in the field and recent completed railway projects. The example rail projects will present the various benefits that soil mixing provides to railway construction and maintenance. Bench-scale studies and full scale implementation as well as soil construction properties before and after mass stabilization will be discussed. The paper and presentation will include information on the advantages of mixing methods and binding agent delivery systems.INTRODUCTIONNew or existing railroad right-of-ways may cross ground with low bearing capacity. Right of way subgrade undergo deflection (strain) as loads (stress) are applied. The amount of strain or deflection of the subgrade caused by loading of a train is proportional to the stiffness of the subgrade materials. Some soils, such as tamped ballast, are very stiff and resist loads well. Other soils such as soft clay, peat, or loose sand have low stiffness and undergo substantial movement under loads. It is very desirable to have the stiffest possible material in a track subgrade. Stiff subgrade material limits deflection under load, reducing track roughness and occurrence of track defects. Mass stabilization is a geotechnical method that can be used to improve the bearing capacity or stiffness of soil in these right-of-way. Mass stabilization involves mixing binding agents into soil subject to treatment while the soil remains in-place or insitu. Variations in the design or areas subject to treatment can be used to address transmission of vibration to adjacent structures."

Jan 1, 2015

By Scott A. Walker, Gabriel J. Alcantar, Brian Zuckerman, Ramin Golesorkhi

"The new San Francisco 49ers Levi’s Stadium is part of the next generation of sporting facilities. Constructed in Santa Clara, Calif., the new structure has 68,500 open-air bowl seats and includes a 7- story tower housing more than 150 suites. The overall project includes the stadium structure, elevated open pedestrian walkways, commercial community space, three new pedestrian bridges and improvements to the adjacent light rail station. Sustainable design for the project includes a green roof, photovoltaic panel and a ground source geothermal system. Stadium-wide next-generation Wi-Fi capability is another feature. The design-build project team included HNTB (project architect), Magnusson Klemencic Associates (MKA, structural designer) and a joint venture of Turner Construction and Devcon Construction (TDJV, general contractor).During preconstruction, the 49ers’ original design team and the design-build team formed later worked together to facilitate communication and provide continuity. This helped to meet the project’s aggressive schedule. Working directly for the 49ers, with the design-build team, Treadwell & Rollo (T&R) served as the geotechnical engineer of record for the project from preliminary to final design and through construction. Although not contracted directly to TDJV, the stadium ownership encouraged direct interaction between T&R and TDJV and improved responsiveness to geotechnical issues during design and construction.Subsurface ConditionsThe new stadium lies within the Santa Clara Valley, a deep alluviumfilled basin resulting from historic movement on the active and potentially active strike-slip and thrust faults that bind the valley. The valley is filled with Holocene age (approximately 11,000 years old to present) alluvium, consisting of levee and basin deposits, with bedrock more than 750 ft (229 m) beneath existing ground surface. The stadium site is between two of the highly-active faults in California, the Hayward Fault 6.8 mi (11 km) northeast, and the San Andreas Fault about 11.8 mi (19 km) southwest."

Jan 1, 2014

By Abolfazl Eslami, Fatemeh Valikhah

"Complexity in soil-foundation interaction and subsoil nonlinear behavior cause difficulties and uncertainties in evaluating the actual values of foundation design factors such as settlement. The acquired continuous records of Cone Penetration Test (CPT) can be used to determine the soil profile and characteristics those are applicable in the geotechnical design. In this paper, it has been attempted to present a new non-linear stress-strain approach to estimate the foundations settlement by using CPT data in the form of soil behavior classification charts. This new approach is based on Janbu method (1960s and also 1998). Instead of using fixed and constant values for stress exponent (j) and modulus number (m), continuous coefficient variations can be used. The proposed approach also can be used as a new method to predict pile group settlement. A data bank has been compiled containing twenty-two practical case histories to investigate the accuracy of the predictions made by the proposed and available common methods. The comparisons indicate that the proposed approach is relatively able to predict the settlement close to their real values. Therefore, it can be considered as an alternative method based on valuable CPT data and nonlinear stress-strain approach for foundations and pile groups settlement estimation.INTRODUCTIONComplexity in soil behaviour for settlement analysis is the result of non-linear and time dependent stressstrain behaviour of soils, their elasto-plastic performance under loading and unloading situation and also effects of stress history (Holtz et al., 2011; Fellenius, 2015). Hence, many relations and equations have been proposed to predict foundation settlement, where most of them are based on typical different parameters such as soil stiffness (E), foundation width (B), contact pressure (q) and pressure developing in depth (Janbu, 1967 also 1998; Briaud and Gibbens, 1999; Uzielli and Mayne, 2012).The Janbu approach for settlement estimation, proposed by Janbu in the early 1960s, combines the basic principles of linear and non-linear stress-strain behaviour of material. The method is applied to all types of soils. The relation between stress and strain is a function of two non-dimensional parameters which are unique for any soil: a stress exponent, “j”, and a modulus number, “m”. The Janbu relations are derived from the definition of tangent modulus by the following expression:"

Jan 1, 2017

By Tsuyoshi Honda, Kazuhiro Kaneda, Masayuki Imai, Kazuo Konishi, Kunio Higashinaka

"In recent years, the demand for measures to control liquefaction of existing airport runways and harbor structures has increased. However, from the perspectives of constructability and cost, application of grid-form deep mixing walls to these types of structures requires the formation of wider grid spacing as compared with conventional designs. In this research, we focused on the extent of liquefaction and ground surface settling when grid spacing is made wider than conventional designs. We conducted centrifuge model tests, and confirmed the liquefaction suppression effect when grid-form modifications involving wide grid spacing are adopted under asphalt pavement. The tests were conducted under conditions that included changing the grid spacing and groundwater level. When the groundwater level was high, an increase in water pressure was observed, even within the grid. However, when the groundwater level was low, the increase in water pressure inside the grid was suppressed. We also found that if the generation of water pressure can be suppressed, the amount of settling due to liquefaction can also be controlled.INTRODUCTIONOne construction technique used as a countermeasure to liquefaction is grid-form deep mixing walls. Grid-form deep mixing walls are a construction technique for which improved grid-shaped wall bodies are built into the ground below the surface using a deep mixing method. This construction technique minimizes shear deformation by surrounding liquefied ground with improved wall bodies, thereby preventing liquefaction (Fig.1). With conventional designs, grid-form deep mixing walls determine the grid spacing that can deter liquefaction based on a ratio of the grid spacing L to the improved depth H (ratio = L/H). Ordinarily, designs are implemented with an L/H ratio of 0.8 or less (PWRI, 1999).In recent years, a demand for measures to control liquefaction of existing airport pavement and harbor structures has increased. However, when liquefaction countermeasures are implemented at these types of facilities and structures, the construction work must be implemented while the facilities and structures remain in service. Therefore, temporal and spatial constraints must be considered. In addition, unlike conventional liquefaction countermeasures, performance requirements are such that, even if some degree of liquefaction is allowed, the performance is acceptable as long as the amount of settlement is within a predetermined value. Therefore, if grid-form deep mixing walls are applied to these structures, grid spacing that is wider than conventional standards is desired."

Jan 1, 2015

By Charles M. Wilk

"Mass stabilization involves mixing binding agents into marginal or contaminated soil to improve the subject material’s physical and/or chemical properties. This paper concentrates on the principles of soil mixing and benefits and application to new and existing rail right-of-way. Successfully applied in Scandinavia and other European countries, the soil mixing is now being applied in right of way in the northern latitudes of the U.S. and Canada. These regions have significant areas of “peaty” soils that can complicate construction and maintenance of rail and structure foundations. Mass stabilization can be used to improve the bearing strength of these soft soils for subsequent construction of railroads, pipelines, roads, and buildings. In civil engineering, the technology is often used to improve the construction properties such as bearing strength, of a marginal soil. In environmental engineering, stabilization is remediation treatment technology that protects human health and the environment by immobilizing hazardous constituents within the treated material. . The treatment is conducted while the subject material remains in-place (insitu). Mass Stabilization is often used to accomplish both civil and environmental purposes on the same project effectively addressing marginal soil while eliminating the expense of soil removal and replacement.This paper presents the principles of mass stabilization technology, implementation in the field and recent completed railway projects.The example rail projects will present the various benefits that soil mixing provides to railway construction and maintenance. Bench-scale studies and full scale implementation as well as soil construction properties before and after mass stabilization will be discussed. The paper and presentation will include information on the advantages of mixing methods and binding agent delivery systems.INTRODUCTIONNew or existing railroad right-of-ways may cross ground with low bearing capacity. Right of way subgrade undergo deflection (strain) as loads (stress) are applied (1). The amount of strain or deflection of the subgrade caused by loading of a train is proportional to the stiffness of the subgrade materials. Some soils, such as tamped ballast, are very stiff and resist loads well. Other soils such as soft clay, peat, or loose sand have low stiffness and undergo substantial movement under loads. It is very desirable to have the stiffest possible material in a track subgrade. Stiff subgrade material limits deflection under load, reducing track roughness and occurrence of track defects. Mass stabilization is a geotechnical method that can be used to improve the bearing capacity or stiffness of soil in these right-of-way. Mass stabilization involves mixing binding agents into soil subject to treatment while the soil remains in-place or insitu. Variations in the design or areas subject to treatment can be used to address transmission of vibration to adjacent structures."

Jan 1, 2017

By Dale Berner, Michael O’Sullivan

"This article focuses on lessons learned from innovative designs including in-the-wet construction methodology and modified foundation conditions, for two United States Army Corps of Engineers (USACE) megaprojects. Olmsted Dam FoundationThe over $2 billion Olmsted Dam on the Ohio River is currently under construction 16 mi (29.6 km) upstream from the confluence with the Mississippi River. The project is under the jurisdiction of the Louisville District of the USACE. It will consist of an 800 ft (244 m) long tainter gate section, a 1,400 ft (427 m) navigable pass, two boat abutment sections, a fixed weir section, and upstream and downstream scour protection. The Olmsted Dam and its two 1,200 ft (366 m) locks, which were built in 2002, will eventually replace both Locks and Dam #52 and #53, both built in 1929, and thereby bring significant benefits to the Ohio River navigation system.In 2002, the Jacobs/COWI JV completed the design of the dam; which was an engineering challenge for several reasons. A significant consideration was its proximity to the New Madrid Fault, which could impose an 8.4 Richter scale seismic event on the structure, which is located in an area of potentially liquefiable alluvium. The extensive seismic analysis performed by the designer included a response spectra analyses, lateral pushover analyses of pile foundations, hydrodynamic added masses, pile group effects, and the development of kinematic motions as a result of the soil-pilestructure interaction."

Jan 1, 2016

By Jochen Maurer, Dr. Christian Hoyme, Dr. Hans Regler

Currently, it is very difficult to obtain qualitative and quantitative information about the status and production process of a construction site. As a rule, companies depend on reports from on-site experts. There is no end-to-end digitalization due to the mobility of equipment and ever-changing locations. Equipment from different manufacturers, especially in special foundation engineering, is highly specialized. Any data collected by this equipment is recorded in proprietary formats and made available on the manufacturers' platforms. This exacerbates the situation, making simple analysis of performance indicators impossible. Most functions such as construction diaries, equipment utilization analyses, etc. are implemented only as standalone solutions. This does not allow for prompt visualization and intervention in critical process sequences because the construction site process is usually managed using a cost-based method. Furthermore, special foundation engineering requires a high level of expertise in an extremely wide range of construction processes. In this article, the results from a set of non-proprietary performance analysis tools are presented using numerous practical examples. Once a construction element is completed, the equipment data is immediately transferred to the platform using the latest cloud technology. Because the data is normalized, construction progress can be documented immediately, even for mixed equipment fleets. Bottlenecks can be immediately detected by visualizing the current performance of the production process, which is broken down into individual steps. Modern analyses of this equipment data improve quality, thereby providing better information about current performance. These sets of tools are essential for changing from the current monetary or cost-based method of process management to time- and bottleneck-oriented management. This makes it much easier to identify the critical path during projects. The article shows that processes can be documented and managed.

By Tracy Brettmann, Shailendra Endley, Jason Leary, Shashank Valluru

"Augered Cast-in-Place (ACIP) piles have long been used for deep foundation support in sands due to their high capacity and speed of installation. Very little information exists on the effects on capacity if the auger needs to be withdrawn from the hole prior to grouting. This condition can occur due to various reasons including grout plug ups, equipment issues, and grout supply delivery problems. It can become a major problem for the project team if this happens during production because the capacity of that pile is then in question, potentially resulting in re-design, installation of replacement piles and/or schedule delays. This paper compares the results of two high capacity test piles installed into a dense sand where one test pile was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth and the other test pile was installed utilizing conventional industry standard methods. Identical load tests were then performed on both piles to compare the effects of the two different installation procedures. The load test results were surprisingly similar in this case although the grout take required for the test pile installed in the pre-drilled hole was significantly higher to produce a similar grout return depth.IntroductionAugered Cast-in-Place (ACIP) piles are used extensively along the Texas Gulf Coast due to their combination of high capacity and speed of installation resulting in one of the most cost effective deep foundation systems relative to other options. Soil conditions in this region typically consist of alternating layers of sand and clay in the upper several hundred feet. ACIP piles are routinely installed to depths of over 100-ft to achieve the required capacity depending on the site specific soil conditions and therefore typically extend through and tip into sand layers. Occasionally, due to various reasons like equipment issues and plug-ups, the auger is withdrawn from the hole without grouting. Significant sand in the soil profile could lead to questions about the effect of the auger withdrawal on the pile capacity and load deflection relationship.This paper summarizes the results of two identical pile load tests performed on adjacent piles of the same length with the main difference being one was installed using the standard installation procedure and the other was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth. The load test results were then evaluated using load transfer analyses to estimate the effect of the withdrawal of the auger on the load-deflection characteristics and capacity."

Jan 1, 2017

By Bastian Hoffmann, Christian Moormann

The paper presents results of an experimental study on the axial load bearing behavior of vibratory driven full displacement piles in comparison with impact driven and cyclic quasi-static installed piles in dense sand. The test setup and the measurement devices used to this end are explained. Subsequently, the results of the axial loading like load settlement curves are shown and the impact of the installation method is interpreted. The results presented in this work are mainly based on three installation methods: test series one investigates axial behavior of vibratory driven piles, test series two describe the same cyclic pile installation process but without dynamic influence wherein a special test setup developed to install the piles cyclic quasi-static in the soil was used. A third test series carried out using the conventional impact pile driving method served the purpose of not only comparing the results against vibratory driving, but also aided in isolating the effects of dynamics inherent to the vibratory driving process.

May 1, 2022

By Kazuyoshi Kamimura, Masaya Kawata

"It has been 30 years since the cement deep mixing (CDM) method developed in Japan. CDM method has been applied to many structures. While various technical improvements have been implemented in the meantime, the single-axial and double-axial technologies used at the time of its initial development are still prevalent.In response to the recent trend of reducing construction costs, we developed a triple-axial CDM method called the “Lemni 2/3 Method.” This method uses two lemniscate motions caused by newly developed auxiliary stirring devices and employs a double-axial injection method in which the cement slurry injection takes place only from the outer two axes. In this way, it is possible to create a stabilized body around the three axes. Moreover, this method does not require substantial equipment investment as conventional construction machine and facilities can be used without modification and large volume work is possible.With these technologies, this method can achieve a substantial reduction in the construction period and cost, while ensuring the same level of improvement quality as conventional methods. As a result, this method is being applied to ground improvement work in a variety of places.Lemni 2/3 Method was first put to practical use in 2004. Since then, the method has been used for ten projects. In this paper, we show some application examples of this method.OUTLINE OF TRIPLE-AXIAL CDM METHOD (LEMNI 2/3 METHOD)In the newly developed CDM method (Lemni 2/3 Method), work efficiency is improved by employing triple-axial stirring blades instead of the conventional single- or double-axial type. Existing conventional construction facilities for double-axial type can be used with only minor equipment additions, because the cement slurry injection takes place only from the outer two axes.Construction Machine and Construction MethodThe combination of major construction machines of the Lemni 2/3 Method differs little from the standard specifications of the double-axial type as shown in Fig. 1. Existing work control equipment can be used without modification, which is further evidence of the simplicity, convenience, and economy of the new method. The Fig. 2 photo shows a full view of the construction machine, and the Fig. 3 photo shows the stirring blades and the auxiliary stirring devices. The work procedure for the Lemni 2/3 Method is shown in Fig. 4."

Jan 1, 2015

By Martin B. Hudson, Andrew K. Cho, Rolff B. Knobel, Les R. Chernauskas, Jonathan L. Ernst

ABSTRACT The Bruce Museum, located in Greenwich, Connecticut, is home to an extensive display of art and natural history exhibitions. A large addition was designed to be constructed adjacent to the museum requiring new spread footings to be installed up to 16.5 feet below the existing foundations. The soil conditions at the site consist of highly variable sand and gravel overlying weathered rock and sound bedrock. The Contract Documents called for traditional foundation underpinning. Traditional underpinning techniques, however, presented two major challenges on this Project; (1) deep underpinning pits would be required involving multiple levels and staging with tieback support and (2) the highly variable soil and bedrock composition and elevations presented uncertainty in the design and construction of the pits. In lieu of traditional underpinning, Geosciences Testing and Research, Inc. (GTR) proposed an “active” soil nail underpinning system. A major reason that the soil nail underpinning option was feasible, related to the fact that the soil nails and facing could be installed slightly in front of the existing footings rather than directly underneath the existing footings. The soil nail wall design involved one to four rows of soil nails with nail positions and wall depth able to be adjusted “on the fly” as excavation progressed depending on the field conditions encountered. To create the “active system,” the soil nails were pre-loaded to mitigate wall deformations that would be associated with a standard passive soil nail wall design. To evaluate the performance of the active soil nail wall and confirm design assumptions, an extensive automated monitoring, on-site testing and inspection program was proposed and executed by GTR to monitor deformations of the wall and the museum in real-time, evaluate and confirm bedrock and soil bond stresses and ensure that each soil nail was pre-loaded and locked off. Careful analysis, planning, and use of the observational method illustrates the importance of collaboration between design and construction personnel and applying engineering judgement throughout construction. The use of the observational method includes the potential for modifying design based on conditions observed. This paper presents a unique case study of the “active” soil nail underpinning system to support and protect sensitive structures, close collaboration between design and construction facilitated by real-time deformation monitoring, and its successful application as a safe and cost-effective alternative to traditional underpinning.

Oct 1, 2022

By Alexander Blatt, Franz-Werner Gerressen

Diaphragm walls are known as underground structural elements commonly used as retention systems for excavation pits and shafts and permanent foundation walls or elements. One can anticipate that global urbanization and increasing demands on environmental considerations will need to be accommodated in underground space in the future. These trends show an increasing requirement for diaphragm walling in even more complex conditions, especially in inner-city applications with limited space. Complex conditions in terms of space limitations, especially for inner city job sites, require specifically adapted solutions for slurry, spoil, reinforcement and concrete handling and the related logistics to ensure smooth production. Furthermore, one focus will be given to the QA/QC topics of the production process. Real time installation control, data transfer and reporting systems become more and more important. Therefore, the paper will describe the construction method and the sequence of activities required for the construction of diaphragm wall systems. It will describe also the main equipment that will be needed to execute these works under various conditions. In addition to the general description of the system and the required equipment, the paper will show some site examples for infrastructure projects with their specific solutions when working under space restrictions.

Nov 1, 2022

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By Karen Dawson

This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.

By Dominic Parmantier, Karen Dawson, Suthan Pooranampillai, Seungcheol Shin

"This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.IntroductionStone column ground improvement was implemented as a means of supporting mechanically stabilized wall approaches for a new bridge over the Puyallup River, part of HOV improvements to I-5 in Tacoma, Washington. The work discussed in this case history was part of the Washington State Department of Transportation (WSDOT) I-5/Portland Avenue to Port of Tacoma Road, Stage 1 Northbound HOV contract, developed as an early work element to a follow-on bridge construction project. The area requiring stone column ground improvement is shown in Figure 1. The improved ground supports permanent geosynthetic walls and embankments up to 50 feet high. This wall can be seen in Figure 1. The selected ground improvement primarily provides global stability of the soils beneath the walls during anticipated seismic loading and also reduces the time and magnitude of consolidation settlement under the weight of the planned embankment.Approximately 74,000 cubic yards of liquefiable alluvial soils were improved by stone columns. Stone column construction occurred in late 2010 and early 2011. This was followed by the embankment and wall construction. Settlement monitoring began with the embankment construction and continued into 2012."

Jan 1, 2017

By Rimas Veitas, James Panton, Erich Steinlechner

"Ductile Iron Piles (DIPs) are a proven, viable alternative to conventional piles, and for the past five years have been successfully used throughout New England. The installation process of DIPs lends itself to both large and small projects. Because of their installation efficiency they provide a substantial cost savings over drilled micro piles. Several New England projects (both end bearing and friction) will be evaluated, focusing on the installation and design procedures.BackgroundThe driven ductile cast iron pile (DIP) is a simple, fast and highly effective pile system. Over the last 30 years over 10 million feet of this pile system has been installed worldwide predominantly in Europe. DIPs are a prefabricated driven pile system utilizing high strength ductile iron pipes which are manufactured using a spun-cast process having outside diameters of 4 5/8” and 6 5/8 inches. The standard pile lengths are 16.4 feet long. The pipes are manufactured with a tapered socket with an internal shoulder for full engagement at the top and a tapered spigot at the bottom. The individual pile sections can be connected with this Plug and Drive® connection to drive a pile of any length.(see figure 1)The DIP system’s inherent advantage is the simplicity of the installation process. The piles are driven to refusal or to a required penetration depth with the use of a high-impact highfrequency hydraulic hammer (ie. Breaker hammer). In most applications the hydraulic hammer is mounted on an appropriately sized excavator (see Photo 2). At the completion of driving the pile, the pile is cut off (see photo 5) and the remaining section of pile is fitted with the appropriate driving shoe and serves as the lead section for the next pile. Being able to reuse the cut off section, yields minimal if any pile shaft waste. The pile is then fitted with an appropriate pile cap plate to receive the load from the superstructure."

Jan 1, 2017

By Emad Farouz

This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule. This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.

By Emad Farouz, Francis A. Abreu

"This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule.This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.SITE AND PROJECT DESCRIPTIONThe Great Neck Water Pollution Control District (GNWPCD), located in the Town of North Hempstead in Nassau, New York, owns and operates a municipal wastewater treatment plant (WWTP) that discharges treated effluent through an outfall to Manhasset Bay, which is a tributary of the Long Island Sound. The site is located west of Manhasset Bay and is surrounded on three sides by local roads, and commercial, industrial, and recreational properties. The site has a gentle slope ranging from elevation +20 to +7 from west to east, respectively, based on the Nassau County Datum.To comply with new nitrogen discharge requirements and new design flows, the GNWPCD contracted CH2M HILL, Inc. and William F. Cosulich Associates as a Joint- Venture (JV) to design and provide services during construction of eight new advanced nitrogen removal facilities."

Jan 1, 2017