Search Documents

By A. S. Nortjé

At South Deep Gold Mine longhole stopes are backfilled using a cemented Cyclone Classified Tailings in its hydraulic state. The need to contain the hydraulic fill until cured requires a barricade. Due to the massive size of the stopes, the tailings can exert enormous forces on any such barricade. Barricades have long been in use, but recent failures in Australia and the large rate of filling required at South Deep solicited a robust design. A robust design must examine all foreseeable failures and the barricade must be able to resist all expected and, within limits, unexpected loads. The design should also be simple to construct and cost effective, limiting the impact of construction errors and unnecessary delays to production.

May 1, 2007

By Adil Aledresse, N. Emre Altun, Bern Klein, Nuri Hmidi, Brent Hilscher

A study was conducted to investigate high gold grades in water lines and carbon fines collected from the Musselwhite gold recovery circuit. It was discovered that fine magnetic particles in the overflow from the carbon fines settling tank launder had high gold grades ranging from 2,000 to7,000 g/t. The -37 micron fraction had up to 17,000 g/t gold. Scanning electron microscopy revealed the gold was attached to the surface of iron particles. The objective of the study was to identify possible mechanisms that result in the attachment of the gold to the magnetic iron particle surface and to recommend process modifications that would reduce these types of gold losses around the carbon circuits. Solid and solution samples were collected from the gold recovery circuit and analysed. Two possible mechanisms were identified including gold cementation onto iron and heterocoagulation of colloidal gold onto iron oxides in the elution column. Possible sources of the colloidal gold include reduction of gold cyanide complex to metallic gold in the carbon regeneration kiln and gold detached from cathode in EW cell. Based on SEM+EDX, the sources of iron were natural magnetite and roasted iron sulphides. Thermal reduction of gold is believed to be the cause of dendritic gold from the carbon regeneration kiln.

Jan 1, 2014

By A. E. Wraith, J. Protheroe Jones, P. J. Mackey

The world’s first copper electrorefinery started production in 1869 at Burry Port in South Wales. Built within the Pembrey Copper Works which had commenced smelting operations in 1849, the new refinery was based on principles described in the British patents issued to J.B. Elkington in 1865 and 1869. Refining principles and practices pioneered there were key to the foundation of modern electro-refining practice in what is now a dominant international industry producing over 16 Mt of electrical grade copper annually. This paper explores the background to this pioneering application of the new, early 19th century, science of “electro-metallurgy” and examines its links to the contemporary decorative electro-plating industry and to the shortcomings of 19th century fire refining. The beginnings and early years of the Pembrey electrorefinery are briefly discussed in relation to the quality, applications and pyrometallurgy of copper at the time. More than a decade would elapse before the birth of the electrical age: the Pembrey refinery may be seen as one of its vital precursors. Note: This paper was originally published as part of the Copper 2013 proceedings (A.E. Wraith, P.J. Mackey and J. (formerly R.) Protheroe Jones, “Origins of Electrorefining: Birth of the Technology and the World’s First Commercial Electro-Refinery”, paper in Electrorefining, Vol. V, Book 2, (Eds. R. Abel and C. Delgado), Cu 2013 International Conference, pp. 19-33, IIMCh, Santiago, Chile, 2013). It is reproduced here together with a new Appendix and supporting references that lists the year of commencement of the first electrolytic copper refinery by country, 1869 to 1956. It all, the year of the first electrolytic copper refinery established for 15 countries is included. These 15 countries now produce more that 70% of world refined copper (for 2018). INTRODUCTION In the 1840s, the new science of ‘electro-metallurgy’, a term coined by Smee in 1841 (Smee, 1841), was being adapted to the decorative electro-deposition of silver in a thin, bright adherent coating that was evidently equal in appearance to traditional silverware (Williams, 1976). Chief among innovative manufacturers of decorative objects who took up the new art of silver electro-plating was the acclaimed firm of G.R. Elkington and Co. of Birmingham, England. The company, which vigorously developed all aspects of electro-metallurgy for the decorative trade, entered the field of ‘electrotyping’, a technique in which the surface features of a mould are copied on an electro-deposited copper layer which, when stripped off, can be used to reproduce an imprint of the mould. In essence, it is a form of casting by electrodeposition, invented in 1837 independently by Jacobi in Russia (Pavlova, 1968) and Spencer in England (Wyatt, 1851).

Jan 1, 2019

By J. Budac, R. Krentz, P. Cordingley, G. Freeman, M. E. Chalkley, H. Scheie

Pressure hydrometallurgical unit operations have been in commercial use at the Fort Saskatchewan refinery of Sherritt International Corporation for fifty years. This paper traces the history of Sherritt from its origins in northern Manitoba, and the development of the first hydrometallurgical nickel-cobalt refinery in 1954, utilizing pressure hydrometallurgy, to the modern day refinery. Sherritt's involvement with pressure hydrometallurgy during the past 50 years has included the operation of the refinery, the development and licensing of technology, incorporating pressure hydrometallurgical unit operations, to more than 30 companies worldwide, the joint venture at Moa, Cuba involving both leaching and precipitation at elevated temperature and pressure, and the production of specialty metal powders. Developments in each of these areas are reviewed.

Jan 1, 2004

?Why TSM in Canada ?How it was developed ?Architecture and Goverance ?COI panel ?Performance indicators and how they work ?External Verification ?Reporting ?The national organization of the Canadian mining industry ?Mining, smelting and refining of base and precious metals ?Mining of iron ore, diamonds, uranium, oil sands, coal and industrial minerals ?Many associate members ?www.mining.ca

May 1, 2011

By V. N. Bryant

"1.0 SYNOPSISThe Colomac property, located 137 miles by air northwest of Yellowknife in Canada's NWT. will recover gold from 10,000 tons per day of open pit ore.The decision to proceed with the project was based on a mineable ore reserve of 16 million tons (including dilution) averaging 0.064 oz/ton. After an in-fill drilling program in the latter half of 1988, Colomac's mineable, proven and probable ore reserves were increased to 28 million tons averaging 0.056 oz/ton of gold.A feasibility study completed by Wright Engineers for Neptune Resources in December 1987 examined the possibility of vat leaching followed by C.l.P. and electrowinning. A second feasibility study completed by Wright in February 1988 demonstrated that a conventional agitated leach circuit using a finer grind justified the higher capital cost of this process. This study was accepted and formed the basis of the project authorization.Preliminary engineering commenced in April 1988 and detailed engineering was started in September of that year with the objective of a mine/mill start-up by early 1990.The short time period available to meet the project deadline was additionally challenging, as site access is either by plane year round, and winter road from early February to late March. Normal lead times for equipment design, specifications, quotations and bid analyses were not possible, if the winter road time-slot was to be met."

Jan 1, 1990

By Michel R. Julien, Michel Lemieux, Jean Cayouette, Daniel Talbot

"The Louvicourt Mine located near Val d’Or, Quebec has been in operation since 1994. It produces copper and zinc concentrates. The tailings generated from the ore processing operations have a strong net acid generating potential. Louvicourt Mine, a grass root project, was designed for closure with the best available technology at the time of design. In order to inhibit short and long time acid potential generation, sub-aqueous disposal was selected at the design stage. Given the fact that disposal in a natural lake was ruled out up front for obvious reasons related to loss of natural habitat and risks of permitting delays, a man made facility built with dams was planned. This mine includes therefore the first fully man-made sub-aqueous tailings disposal facility built in Canada. The requirement of using sub-aqueous disposal had serious implications on the placement of tailings. This tailings facility located about 9 km from the mine site has been selected based on the available natural confinement, the favorable foundation and hydrogeological conditions. This paper describes the site and the design criteria that were used. A presentation is also made on the placement technique to maximize storage and its impact on the operation of the basin. The performance of the basin, the dams and the decant structures is reviewed.Résumé : La mine Louvicourt, située près de Val d’Or, Québec est opérationnelle depuis 1994. Elle produit des concentrés de cuivre et de zinc. Les résidus générés par les opérations de traitement du minerai possèdent un fort potentiel net de génération d’acide. Le parc à résidus de la mine Louvicourt, implanté dans un milieu naturel intact, fut doté dès sa conception initiale de la meilleure technologie de fermeture disponible à l’époque, soit la déposition sous couverture aqueuse et ce, dans le but de bloquer le potentiel de génération d’acide à court et à long terme des résidus. Etant donné que la déposition dans un lac naturel fut mise de côté dès le départ pour des raisons évidentes reliées à la perte d’habitats naturels et au risque d’introduire des délais dans l’émission des permis, un étang artificiel délimité par des digues a été conçu. Cette mine fut donc la première au Canada à être dotée d’une installation anthropique de disposition des résidus sous une pleine couverture aqueuse. L’exigence d’une déposition sous couverture aqueuse a eu des implications sur le mode de mise en place des résidus. L’emplacement de l’installation de gestion des résidus a été choisi en un lieu situé à environ 9 km du concentrateur sur la base du confinement naturel disponible et des conditions hydrogéologiques et géotechniques favorables. Cet article décrit le site et les critères de conception utilisés. Une présentation est faite sur la technique de mise en place utilisée pour maximiser l’entreposage et son impact sur l’opération du bassin. La performance du bassin, des digues et des structures de décantation est également revue."

Jan 1, 2004

By Bryan M. Maybee

The scheduling of underground mining activities is a complex task, in particular because of the requirement to satisfy a large number of constraints. A Schedule Optimization Tool (SOT) for underground mine planning is described, and its use for investigating strategic decisions is illustrated by means of a case study. The main components of SOT include: a genetic algorithm, which searches for optimal schedules; guidance, the application of heuristic rules to guide the genetic algorithm; and sliding, which implements just-in-time development. For the case study, SOT is employed to generate schedules at various ore capacities, accounting for the appropriate financials in each schedule evaluation. The case study finds that preliminary scheduling performed before invoking SOT, intended to provide a good starting point for the search, does not ultimately lead to higher value schedules. Two key uses for SOT are identified. A mine planner can save time by using SOT to produce high-value scheduling alternatives. This process ensures a broader investigation of the value that the deposit can yield. Also, SOT can be used to validate strategic and tactical decisions, by scheduling under alternative scenarios. Both uses produce high value schedules conforming to all imposed resource constraints.

May 1, 2009

By R. Simkus, J. K. Gowans

Polaris Operations, a Cominco Ltd. lead-zinc mine, is located on Little Cornwallis Island, Northwest Territories, at Latitude 75°23' N and Longitude 96°75' w. When the Polaris Mine went into operation in late 1981, it became the world's most northerly base metal mine.The Polaris Concentrator, housed in a unique process barge, is a basic lead-zinc concentrator where flotation is used to produce the lead and zinc concentrates.The paper describes the ""coarse lead"" flotation feature incorporated in the concentrator flowsheet and describes the start-up problems and continuing operation of this circuit.

Jan 1, 1984

"Load-haul-dump machines (LHDs) are typically used in underground metal mining operations. Delays or inappropriate use of LHDs can result in production loss. Optimized LHD use is especially crucial in larger mines because longer travel distances increase heat, dust, and gas emissions, which in turn increase ventilation costs. This study, conducted at an existing Swedish sublevel cave underground mine, used discrete event simulation and the AutoMod™ DES tool to determine the ventilation costs related to using too many diesel LHDs in a production area with reduced ore pass availability. When fewer ore passes are available, ventilation costs related to operating LHDs in the production area were found to increase by as much as 200, 224, and 306% for one, three, and six LHDs in operation, respectively. ¦ KEYWORDS Discrete event simulation (DES), Loading operations, Production rate, Ventilation costs RÉSUMÉ Dans les exploitations souterraines d’extraction des métaux, on utilise généralement des chargeurs-transporteurs (LHD, de l’anglais Load-haul-dump machines). Les retards ou l’utilisation abusive des LHD peuvent entraîner une perte de production. L’utilisation optimisée des LHD est particulièrement importante dans les grandes mines en raison des longues distances parcourues, lesquelles augmentent la chaleur, la poussière et les émissions de gaz qui, à leur tour, décuplent les coûts de l’aérage. Cette étude, menée en Suède dans une mine souterraine utilisant la méthode d’exploitation en sous étages avec foudroyage, s’est basée sur la simulation à événements discrets (SED) et l’outil de SED AutoMod™ pour déterminer les coûts de l’aérage liés à l’utilisation d’un nombre trop élevé de LHD alimentés au diesel dans la zone de production, avec une disponibilité réduite de la cheminée à minerai. Lorsque les mines disposent de moins de cheminées à minerai, l’étude montre que les coûts de l’aérage liés à l’exploitation des LHD dans la zone de production augmentent respectivement de 200, 224 et 306 % pour un, trois et six LHD en fonctionnement. ¦ MOTS CLÉS coûts de l’aérage, opérations de chargement, simulation à événements discrets (SED), taux de productionINTRODUCTION Transporting material from the mine face to the dumping location requires flexible loading and hauling equipment that is able to cope with sharp curves and a complex mining environment. Load-haul-dump machines (LHDs) are designed for such an environment. Models are available to suit specific features of the working environment such as small, large, or narrow open stopes (Atlas Copco Rock Drills AB, 2007). When carrying a full load, haulage speed is higher for LHDs than for front-end loaders with the same engine size. Also, payloads are approximately 50% higher for LHDs than for front-end loaders (Atlas Copco Rock Drills AB, 2007). LHDs are capable of climbing steep (Bloss, Harvey, Grant, & Routley, 2011). The haulage distance between stope and ore pass is usually between 50 m and 400 m. LHDs are efficient for tramming distances up to 200 m (Bloss et al., 2011), whereas when loading trucks, the LHDs work efficiently when the distance is less than 100 m (Atlas Copco Rock Drills AB, 2007). The largest diesel-powered LHDs, with drive motors of up to 350 kW, can handle a payload of 21 t (Wennmohs, 2014). Most mining equipment runs on diesel fuel, which provides flexibility, high durability, and high efficiency (Pronk, Coble, & Stewart, 2009); however, other alternatives such as electric, hybrid diesel/electric, or hydrogen fuel cell machines are increasingly being developed and used. This change is due to diesel-powered machines accounting for a significant portion of the ventilation costs in the mine (Chadwick, 2008; Paraszczak, Laflamme, & Fytas, 2013). Currently, as part of the European sustainable intelligent mining systems (SIMS) project, Epiroc AB is planning to demonstrate technology for a diesel-free underground mine at Agnico Eagle’s Kittlä mine in Finland using"

Jan 1, 2019

By T. Peters, W. C. Ferguson

"Shebandowan is about 600 miles west of Sudbury and 50 miles west of Thunderbay close to the trans Canada highway. Shebandowan Lake is about 38 miles long. The ore body is located between No. 1 and No. 2 shafts at the lower end of the lake. The economic mineralization lies between 200 and 2000 feet below. Years ago development of this ore body would probably have entailed draining the lake and using the open pit method to mine the ore.The water of Gold Creek which flows into Lake Shebandowan is representative of all local waters and is very close to rain water in purity. It is obvious that any industrial water discharged would have a measurable impact on the local water. The dissolved solids content is low and consistent with what is normally found in northern Ontario.A Koepe headframe is the only visible evidence of the mine from the lake. The Koepe headframe is esthetically pleasing and quiet in operation. The structure is of concrete to control noise. Noise from ore dumping is controlled by dumping underground to an ore pocket 400 feet below the surface. A 3600 foot conveyor belt carries the ore underground to the mill and is out of sight of the lake and the cottagers. The main objective to all our environmental efforts has been to preserve the natural beauty of the region. The mill is housed in a conventional metal-clad-siding building painted in esthetically pleasing colours. A single service building houses warehouse, dry storage and offices. The area surrounding the mill and service building is paved or grassed and drainage from this area is collected and pumped to the tailings area. Air intake silencers are installed on the compressors which are mounted at the back of the mill. Sound measurements taken on the lake indicate that noise suppression is excellent."

Jan 1, 1975

By D. R. Tesarik

Researchers from the National Institute for Occupational Safety and Health (NIOSH)1 and engineers from Placer Dome, Inc.2, conducted an underground rockfill span test at the Turquoise Ridge Mine near Golconda, Nevada, USA with the purpose of improving safety and increasing productivity by using a bulk mining method instead of drift and fill. A rockfill sill was constructed by mining and backfilling six adjacent, parallel drifts and then undercutting the sill with a 13.7 m (45 ft) wide and 30.5 m (100 ft) long room. Displacement measurements from vertical borehole extensometers installed in the mine roof and rockfill indicated that the sill remained stable with a maximum vertical deformation of less than 5 mm (0.2 in). These results were confirmed by visual observations and calculations from a validated three-dimensional numeric model of the sill. The numeric model was also used to simulate load on the sill produced by dislodged roof material in the shape of a 11.0 m- (36 ft-) high triangular prism with base measurements equal to those of the sill. Failure in the bottom third of the sill occurred with this additional load.

May 1, 2007

By Daniel Hodouin, Claude Bazin

"This paper examines the economic advantages of tuning the operation of a differential Cu-Zn flotation circuit as a function of metal prices. Three operating strategies are considered in the analysis: 1) the operation of the circuit at planned copper and zinc concentrates grade with maximum recovery of both metals; 2) the operation of the Cu circuit at maximum copper smelter return per ton of ore and of the Zn circuit at a maximum zinc smelter return per ton of ore; and 3) the operation of the circuit at maximum copper and zinc smelter return per ton of ore. The second strategy tunes the copper circuit independently from the zinc circuit, while the third strategy tunes both circuits simultaneously IntroductionMetal prices play a very important role in the mineral industry (Malhotra and Dowling, 1991). In many cases, metal prices can be the basis for the GO/NO GO decision of a mining project (Malhotra and Dowling, 1991; Apostolides, 1983; Davis, 1996). This direct impact of metal prices on company revenues is highlighted in many annual reports. The 1995 Noranda Annual Report indicates that a variation of 10% of the copper price impacts its yearly revenues by $25,000,000. Some mine operators claim to mine stopes as a function of metal prices (Liimatainen, 1996; Hartman, 1992). This impact of metal prices is also recognized by mill operators that seek strategies to tune ore processing circuits to maximize revenues from the concentrate they sell to smelters (McKee, 1991; Barker et al., 1989; Hales and Ynchausti, 1994; Cipriano et al., 1995). In many cases the problem of tuning the operation of an ore processing circuit is complicated by the fact that the ore contains two or more valuable metals which have to be recovered into separate products. The Agnico-Eagle (Robitaille and Cousin, 1995) and Barrick East Malartic (Pelletier, 1996) Cu-Au mines are examples, as well as the Cu-Pb-Zn Brunswick mine (Shannon et al., 1993) or the Cu-Zn Louvicourt (Whiteway, 1995) and Selbaie (Wright, 1995) mines."

Jan 1, 2000

By George Rice

Foreword Following the explosion in the Hillcrest mine, which occurred in the evening of Sunday, September 19th, 1926, and in which two men lost their lives, the writer was invited by the Hon. J.E. Brownlee, Premier of Alberta, to conduct an investigation into the causes of the disaster, and to make such recommendations as seemed advisable with a view to minimizing as far as possible the chance of future explosions in this and similar Alberta coal mines. Accordingly, the mine was visited, and extensive investigations were made underground on October 21st, 2.2.nd, and 25th, in company with Mr. John T. Stirling, Chief Inspector of Mines for Alberta, Mr. Moses Johnson, District Inspector for the Crowsnest Pass District, Mr. J as. A. Richards, Inspector of Mines, Edmonton, and also Mr. Thomas Davies, manager, and other officials of the Hillcrest mine. Hearings of the coroner's inquest were also attended on October 20th and 23rd, when testimony regarding the explosion was given by various witnesses. The following paper summarizes my general observations in tracing the place of origin of the explosion, and my efforts to determine the cause of ignition. Certain recommendations arc also made, and the writer invites discussion on these and the other matters dealt with in the paper.

Jan 1, 1928

By G. Archibald, M. McSaveney, J. Wartman, M. Yetton, C. Massey, C. Holden, A. Kaiser

"The 2010/11 Canterbury earthquakes triggered many mass movements in the Port Hills including rockfalls, rock and debris avalanches, slides and slumps and associated cliff-top cracking. The most abundant mass movements with the highest risk to people and buildings were rockfalls and rock/debris avalanches. Over 100 residential homes were impacted by landslides, leading to the evacuation of several hundred residents.Volumes of rock leaving several of the larger cliffs during the earthquake sequence were determined from terrestrial laser scan change models. There were no seismically instrumented cliff sites and there was some distance between the cliffs and nearest strong-motion sites. Therefore, we synthesised free-field rock-outcrop seismograms by employing a stochastic approach controlled by source models and regional parameters derived using spectral inversion of the extensive strong motion data set. Relationships between volumes leaving cliffs during the earthquakes and site peak ground acceleration (PGA), peak ground velocity (PGV) and Arias intensity were compared for different sites. Multiple linear regression was used to analyse the variables that best predict the volumes of debris that fell from the slopes during the main earthquakes. The best correlation between the volume of debris falling per square metre of slope face and the seismic forcing parameters was for vertical PGV. The results from the multiple linear regression incorporating slope height, inclination, PGV horizontal and PGV vertical, improved the statistical relationship.Field data and results from the 2D seismic site response assessment indicate that the following factors affect dynamic performance of the modelled cliffs: 1) cliff geology—mainly material modulus, shear strength and shear wave velocity; 2) slope geometry—ridge-scale versus site-scale effects; and 3) the temporal aspects of the earthquake shaking (i.e., single acceleration peaks of large amplitude versus multiple peaks of smaller amplitude). Model results show that amplification of shaking does not increase linearly with increasing height, but instead reflects changes in the cliff geology where material strength, modulus and shear-wave velocity contrasts lead to acceleration contrasts.These factors show that the use of well documented case histories provide the basis for more certainty in seismic landslide assessments compared to those that are only empirically based."

Jan 1, 2015

By Gustav Nillson

There is a difference in design parameters between steel linings and rubber linings for grinding mills. The basic design parameters for rubber are described and a comparison is made between steel and rubber in different applications.

Jan 1, 1979

By Michel Ruel

"This paper describes how to make advanced control choices when difficult processes need improvement. The decision-making process involves choosing between a rules-based approach and a model-based approach as well as weighing benefits and drawbacks, complexity and simplicity, investment and results. This paper will present briefly each solution: basic control, advanced regulatory control, model predictive control, and expert systems such as fuzzy logic controllers and neural networks. The article then proposes a decision tree for selecting the most appropriate approach. A table will compare usage, development, commissioning, maintenance and lifecycle costs for each approach. Finally, conclusions and suggestions will summarize the methodology.INTRODUCTION Advanced process control (APC) is a popular topic. How can one decide whether advanced control should be added to an existing system? Advanced control is used to improve performance, stabilize production, handle constraints, protect equipment and manage grade changes. Most plants use feedback controllers, usually PID (proportional, integral, derivative) controllers. It is common to develop special control schemes to handle more complex processes. In classic PID process control, a controller brings a single value close to a set point using a single manipulated variable. On the other hand, APC brings several values close to optimal targets simultaneously using several manipulated variables. APC's four main strategies are advanced regulatory control, model predictive control (MPC), fuzzy logic and neural networks. Simple solutions are always preferred. Complexity will be increased if performances (production, quality, etc.) are below par. Profitability analyses should be conducted to validate project viability. Needs—not trends—should dictate choices! Before increasing complexity, it is important to define needs, goals, technical support, budget, etc. All these approaches entail strengths and weaknesses. Building a project based on technology rather than needs spells trouble."

Jan 1, 2014

By L. D. Haig

"The Texada Mill is a unique iron operation producing High Grade sinter iron concentrate and a by-product copper, gold, silver concentrate. The plant is complex and extremely flexible to handle the many varieties of ore. Two iron concentrates are made and blended. A coarse iron concentrate from primary grinding and a fine concentrate after rougher flotation to remove all the sulphides.All the tailings from iron processing are collected, dewatered, reground and floated for additional copper recovery.The entire milling operation has been carried out in all sea water for seven years and mixtures of sea, fresh, and reclaimed water for ten years prior to that.A very stable float results from the use of sea water at the natural pH8. Reagent Consumption is lower and Metallic Corrosion of mill liners and grinding media is actually less than local fresh water or mixtures of fresh and sea water.Marine growth in pipe lines can be periodically removed by violently bubbling high pressure air up through the water filled mains.Location:Texada Mines is located on tide water on the west side of Texada Island 100 miles northwest of Vancouver, B. C.The Island is served by a 30 car ferry, tug and barge and a scheduled air service from Vancouver to a company maintained air strip near the mine.The climate is moderate with about 30 inches of rain during the winter and relatively dry summers."

Jan 1, 1974

By A. M. Hill

"This is an account of the expansion of Texasgulf's Timmins concentrator by the building of a fourth circuit.The original capacity of the mine and concentrator was 3.6 million tons per year of ore. In 1974, Texasgulf decided to increase that capacity by about one third to 4.8 million tons per year. It was planned that the increased capacity would be available by mid-1978.The expansion involved work at the rninesite, increased railroad capacity, and a new circuit in the concentrator, and it is the concentrator expansion which is described here.In 1974, the minesite drew its ore from the open pit. The pit was being phased out and was to be replaced by No. 1 mine. To allow for the expansion, a second mine was required. The railroad was capable of handling 18 car trains. Its capacity had to be increased to 27 cars per train and this, in turn, required two new locomotives. Each of these alone cost half a million dollars.The concentrator building in 1974 contained the concentrating equipment and miscellaneous services (such as machine shop, warehouse, analytical lab). The grinding and flotation sections were divided into three circuits ('A', 'B', & 'C'). 'A' and 'B' circuits treated copper-zinc ore and 'C' circuit treated the much more difficult copperzinc- lead ore. This 'C' circuit had been modified over the years to implement improvements in the metallurgy."

Jan 1, 1979

By Sunil Koppalkar, A. R. Laplante

"A Pilot Plant was installed in one of the grinding circuits of the Dome Mill, Ontario, Canada. Tests were conducted on a KCCD12 Knelson Concentrator to systematically analyze the effect of operating variables on the performance. The main objective of this test work was to explore the effect of very coarse (6 mm) feed size on GRG recovery and performance of the Knelson concentrator. Preliminary results have shown that coarse feed size is deleterious to maximizing recovery. Size-by-size GRG recoveries have shown an unusual trend in the sense that recoveries do not decrease monotonically with decreasing gold particle size. Similar trend observed in one other full-scale unit has been compared. The observed trend is probably linked to the feed size distribution and top size.INTRODUCTIONKnelson Concentrators are the most widely used semi-continues centrifuge gravity separation units for the recovery of gold and platinum group minerals (Xiao and Laplante 2004). The main advantages over the competing centrifugal gravity units are their design, operating simplicity and good separation efficiency that make them the most common choice for gravity circuit. Despite some characterization at bench scale and a limited characterization at full scale, there is a lack of a comprehensive study of impact of operating variables on efficiency that reflects realistic full scale operating practice. GRG characterization studies, at bench scale, on these units provide information about the occurrence of gold in ore samples but fail to provide adequate information about the effect of operating variables for full-scale units. It is well known fact that such work is difficult to undertake on full-scale units owing to the difficulties involved in sampling and systematic variation of operating parameters. To tackle these problems, a pilot facility consisting of a 12-in CD Knelson Concentrator, a feed screen and tailing pump was installed in one of the grinding circuits of Dome Mill. This paper describes the work carried out and the results.Porcupine Joint Venture (PJV)Porcupine Joint Venture was formed in 2002 between Placer Dome Inc. and Kinross Gold Corporation. The JV utilizes the milling capacity of the Dome Mill to process ore from Placer Dome and Kinross mines. The Dome Mill circuit has gravity concentration, cyanidation and CIP circuits to recover gold. Gravity recovery has been used at Dome Mill since inception to recover gold: first by using conventional jigs, which were eventually replaced by two Knelson Concentrators in 1993, one in each of the grinding circuits. Three more Knelsons joined the circuit in 2002 to improve gravity recovery. An Acacia Intensive Leach Reactor was also added in 2002 to process gold concentrates replacing shaking tables (Chong et al 2004)."

Jan 1, 2007