Search Documents

By H. A. Hamza, J. Visman

"This is a report on the combined application of ""long-chain"" flocculants and classifier cyclones in the field of slimes treatment, with emphasis on the simultaneous thickening and clarifying of industrial effluents, at low cost. The principle of the process described below involves: (1) the formation of small floes of relatively great strength, by sequential dispersion and conditioning, with average floe size of about 1501 microns; (2) the floes being of sufficient strength to withstand the shearing forces operating within a cyclone and consequently behaving as solid particles with an equivalent diameter (Stokes) that exceeds the size cutpoint of the classifier cyclone; (3) the removal of flocculated solids by means of a classifier cyclone the size cutpoint of which permits effective separation of these solids from the water. Results of test work to date indicate that a broader use of cyclones in industry is possible with the above types of flocculants because the submicron particles and colloidal material are readily collected and clear water is produced, with the attendant advantages of compact construction and low cost that are characteristic of centrifugal separation. The process generally permits classifier cyclones of medium throughput capacity (e.g. 12-in. diam.) to be used for clarifying effluents that contain minus 10-micron particles."

Jan 1, 1973

By P. R. Clark, M. D. Gleghorn

"IntroductionAt TransAlta Utilities Corporation's Highvale Mine, located west of Edmonton, Alberta (Fig. I and 2), dragline stripping has proved to be a practical and economical method of overburden removal and future plans have been based upon the continued use of draglines (Fig. 3) as the major stripping equipment (Williams, 1979, Nikols et al., 1986). However, long range planning has shown that the capacity of draglines alone will be exceeded in the early 1990s as mining progresses into deeper overburden cover (Tapics, 1983). Strip ratios will increase from I.3 bank m!/ t of coal in 1985to 4.5 bank m3 / t in 1995. During this period the depth of overburden will increase substantially and the areas to be mined will be characterized by weak soils including glacially displaced overburden. This increased overburden depth in relatively weak soils will make it impractical to _continue side casting by draglines without prestripping in advance. In 1983, a major investigation was initiated to determine what additional overburden removal equipment was appropriate to the Highvale operations, and recognizing the long delivery times of this major equipment. when it would be required. This paper describes studies and tests which were undertaken in 1983 and 1984 to select prestripping methods and equipment for the future operation of the mine.Previous planning studies have shown that with the current burn schedule and with the economies of progressing from low cover to high cover, as has been practiced in the past, overburden volumes will exceed the capacity of the existing draglines in the early 1990s (Fig. 4). These previous studies had placed reliance on (I tandem dragline operation for future overburden removal requirements up to a depth of 45 m throughout the Highvale Mine. New drilling together with the associated geotechnical studies and some detailed planning on the practicality of using tandem draglines, created concerns about their universal application. Even without considering geotechnical conditions there was a depth limitation to tandem dragJines and substantial prestripping would be required to achieve the ultimate depths."

Jan 1, 1987

The Nak?azdli First Nation and the municipality of Fort St. James are located in the Stuart Lake/Nak?al Bun area and are not unfamiliar to mining. These northern British Columbian communities have been associated with the historic Pinchi Lake Mercury mine and today are closely linked with British Columbia?s newest mine, the Mt. Milligan mine. Prior to the construction of Mt. Milligan, community health and social service providers were concerned about potential impacts that would occur from new mineral development activities. This concern has led to a partnership between the above communities and researchers with expertise in the area of mining and health. This paper describes: the current mining and health environment with a focus on British Columbia; mining trends in the Stuart Lake/Nak?al Bun area; the current community-based health research project funded by the Vancouver Foundation and the Canadian Institutes of Health Research, and; a suite of community-based health recommendations to mining companies on key issues to consider when developing projects near municipalities and Aboriginal communities in Canada, based upon one of the newest mines under development in Canada.

Aug 1, 2013

By C. W. Drury

It is practically fifteen years since stellite was first introduced into industry, and since then the progress made in its manufacture has been so rapid and the number of successful applications so varied that it was considered a review of the more important phases would be of general interest. Stellite is a cobalt-chromium-tungsten alloy, containing approximately 2. 75 per cent carbon. The high percentage of carbon is necessary for the requisite hardness and resistance to wear at ordinary temperatures, whereas the tungsten is essential to impart hardness at a red heat. Chromium imparts hardness and strength, and cobalt renders the alloys more resistant to oxidation. The metals cobalt and chromium are completely soluble in all proportions, both in the liquid and solid state, the equilibrium diagram showing a minimum in the solubility curve at approximately 50 per cent cobalt and l,340°C. Cobalt and tungsten are completely soluble up to 40 per cent tungsten, which is beyond the limit of the; tungsten content of stellite alloys. In the presence of carbon, carbides are formed, which are essential in stellite possessing good cutting or wearing properties.

Jan 1, 1930

By D. Want

In titanium-lined autoclave design the most critical point of its mechanical reliability is its titanium batten strips present at the circumferential and longitudinal barrel-weld seams. Recently an Australian Company, W.E. Smith Hudson (WESH) P/L, has developed a fully flush batten strip and is building autoclaves with this design. Significant research and development has been performed in the process. In this presentation, design aspects of these batten strips are presented that cover topics such as residual-stress magnitudes during fabrication, affect of preheat during batten-strip welding and residual stress in respect to fatigue life. There has been little research done regarding the affects of residual batten stress in relation to fatigue life. Considerations of this 'grey' area of design will be discussed based on the author's research data and finite element analysis.

Jan 1, 2005

By A. L. Irwin

THE problem of compensation for labour is probably the oldest and most complicated one in history. The wage that a man receives is possibly the most concrete thing he gets out of his job and, rightly or wrongly, is generally considered by him to be the most important item in connection with his daily work. How today workers in an equitable way has been the study of industrialists for many years, and a great number of ideas have been tried out in an effort to arrive at a reasonable solution of the question. The idea of establishing a measuring stick for various types of work has intrigued industrial management for a long time and, after considerable study, the principle of Job Evaluation has taken form unti1, at the present time, it is becoming increasingly useful to industry at large. Job evaluation is a plan which is used to determine the relative worth of occupations by means of arbitrary measuring scales. These scales are developed for individual industries and are generally 'tailor made' for each particular case. There are as yet no absolute methods of measuring the work done by human beings and, as a result, one has to depend on comparative values to arrive at conclusions. However, job evaluation has provided us with a basis of negotiation for wage rates which is more satisfactory than mere guess work or persona! opinion. It supplies a common ground for discussion which is understandable by all taking part and ensures that thinking with regard to wage setting is carried out along standard lines.

Jan 1, 1943

By MaryAnn E. Crichton, David G. C. Clarry

"Environmental risk is becoming more important in debt and equity financing decisions in the mining industry worldwide. Demonstration of good environmental management practices and management systems has a direct impact on the ability of mine developers, operators and investors to raise financing. Based on experience in providing due diligence services, there are a number of factors that are important in assessing financial risks related to environmental issues in either new projects or existing facilities. A frame-work for understanding the importance and priorities of each element of environmental management is presented.IntroductionIn the context of lending money to a corporation, environmental issues represent another aspect of credit risk (Henry, 1989). These issues, because of their nature, represent the potential for large unforeseen expenditures if they are not known or acknowledged and are not being proactively managed. Lenders, other investors and their advisors, are becoming increasingly aware of the potential financial impact of environmental issues. Consequently, they are increasing their requirements for environmental audits to review the environmental issues, management practices and systems when they are considering financing mining and/or metallurgical processing operations worldwide.Many banks have signed the United Nations Environment Program (UNEP) Statement by Banks on Environment and Sustainable Development. Banks in this category include National Westminster Bank, the Union Bank of Switzerland, Deutsche Bank, and the Royal Bank of Canada."

Jan 1, 1997

By Michael Boyle, John Zeni

"The Blind shaft boring method is a mechanised process of excavating large diameter vertical shafts downward from the surface. It is a rotary drilling technique eliminating any requirement for personnel to enter the shaft or access underground workings during drilling and lining phases. Excavated material is delivered to surface carried by a flow of circulating fluid through the centre of drill rods. The drill assembly is suspended from a large A-frame rig and powerful winch at ground level providing vertical thrust to a hard rock cutter head. INTRODUCTION The Southern Coalfields Ventilation Shaft was constructed at a mine, 45 km north-west of Wollongong. The 5 m finished diameter (6.2 m drilled) shaft reaches a final drilled depth of 517 m, the deepest, fully lined blind bored vent shaft to date in Australia. Operated by a mining company in the Southern Coalfields, the expanding mine required a new ventilation shaft and associated surface infrastructure to service future operations. An assessment of future ventilation requirements for the coal seam operations identified a need to improve the capacity and reliability of the existing underground ventilation system in order to ensure a safe and efficient underground working environment. Installation of the new upcast ventilation shaft was determined to be the most cost effective and reliable solution to provide adequate ventilation for underground operations. The completed shaft is smooth and fully lined with steel/concrete composite liners that are hydrostatically sealed. The shaft lining is designed to meet the mine ventilation requirements for a service life of 20 years. The shaft intersects the top of the working section of the coal seam at approximately 513 m of depth. This includes the shaft collar depth and shaft bottom profiled intake section.PROJECT METHODOLOGY AND INDUSTRY BEST PRACTICE The shaft was drilled using the blind bore method, an innovative construction technique and an alternative to the traditional methods of sinking deep and large diameter shafts, such as raise boring and conventional drill and blast shaft sinking. The blind bore method allows the shaft to be drilled from the surface down without anyone having to enter the shaft or the mine during the construction process. This is by far the safest method of shaft construction and is especially suitable for difficult ground conditions where there may be unstable or water-charged strata. As this method involves drilling from the surface downward, shafts can be completed ahead of the underground mine development. Thus, allowing underground operations to focus on development and production without the conflicts of managing ventilation priority for underground contractors and mucking out spoil from excavation workings."

Jan 1, 2019

By T. Xu

"The CTL-500 centrifugal extraction machine, which was independently developed by Baotou Shibo Rare Earth Extraction & Equipment Co., Ltd., is presented in this article. The machine is based on centrifugal extraction principle and has been used in P507-HCl-RECl3 extraction system. Automatic control has been utilized in the system. In this paper, a comparison is made between centrifugal extraction and conventional mixer-settler extraction and satisfactory results are shown. INTRODUCTIONCentrifugal extraction is a fast and efficient liquid-liquid extraction method. The process includes solute transfer and separation of the two liquid phases. In the CTL-500 machine, the organic and aqueous phases individually enter a lower mixing chamber in certain proportions and are mixed and dispersed and solute thereby transferred from one phase to the other. The mixed phases pass into a rotating drum and the two liquid phases are separated under centrifugal force. As it flows upward, the aqueous phase, which has a higher specific gravity, flows away from the rotating drum centre towards the drum wall and the organic phase flows towards the drum center. The two liquid phases enter into collection chambers through independent weir plates and are discharged from the machine.The centrifugal extraction machine has been widely used in liquid-liquid separation, either without solid or with small quantities of solids (Chen, Zhang, Zhuo, Chen & Li, 2008; Duan, Jing, Zhu & Chen, 2007; Duan, Zhou & Zhou, 2006). Examples of the use of the centrifugal contactor include the separation of water from crude oil, treatment of heavy oil and diesel to eliminate water and salt; the extraction of penicillin, garlic oil, malathion, and interferon; the hydrometallurgy recovery of nickel, copper and uranium; extraction of edible oil, spice, refined oil and food color; treatment and recycle of print and dyeing wastes; treatment of hydroxybenzene-contaminated sewage by multistage extraction and separation of water from oil in ship sewage."

Jan 1, 2012

By J. Cui, Z. Meng, W. Zhao

"The decomposition of rare earth concentrates containing bastnasite and monazite by alkali solutions has been investigated. A slurry of the rare earth concentrate and the alkali solutions was calcined at different temperatures. The impacts of calcination temperature on the decomposition of rare earth minerals, the oxidation of cerium, the deportment of fluorine and phosphorous, and the adaptability of the method to the different grades of rare earth concentrate were all studied. A possible technique for comprehensive recovery is proposed in which the chemical elements such as rare earth, fluorine, phosphorus, calcium, iron and thorium could be recycled or recovered. INTRODUCTIONThe liquid alkali decomposition method is an important technique for the decomposition of mixed rare earth concentrates. The technique is relatively clean compared with the sulfuric acid roasting method. However, its operation is intermittent rather than continuous. The two-step solid-liquid reaction and the subsequent water washing make it not very suitable for mass production and application. An important reason for the disadvantage is that an additional process of ""calcium removal by acid leaching"" is needed for the technique. The content of calcium in Baotou rare earth concentrates is usually 6-12%. The requirement of the current technique is that the content of calcium should be reduced to about 0.2% after the calcium removal process. Otherwise, the decomposition and leaching of rare earth will be affected. Therefore, calcium removal by acid leaching is a necessity before the alkali decomposition process is carried out. Research on different alkali decomposition techniques has been conducted with prior calcium removal by acid leaching (Xu, 1995; Yu, 1993; Han, Li, Chang, Liu & Xu, 1985). There have been some investigations of direct decomposition of the bastnasite (Feng, Pan & Li, 1998; Zhao, Zhang, Yang & Liu, 2002)and monazite (Sun, Li, Li, Su, Zhao & Liu, 1998; Zhou, 2005) by alkali-liquid, however, all studies were carried out in solid-liquid reaction system, and continuous calcination studies have not been reported.This paper investigates the process of direct decomposition of Baotou rare earth concentrates by continuous calcination with concentrated alkali. Using the rotary tubular electric furnace, the mixture of rare earth concentrate and concentrated alkali solution were decomposed continuously. Satisfactory decomposition results were achieved. A method for clean processing and comprehensive resource recovery from Baotou rare earth concentrates is proposed."

Jan 1, 2012

By Paul B. Warrington

This paper presents a discussion of the factors affecting copper scrap markets, including such items as price levels, freight. grades of material, sources and packaging. Reference will also be made to the effective life and turn-around of the copper content of some products. Introduction IN TERMS OF SIZE, copper scrap is second only to ferrous scrap in tonnage recycled. However, in total value, it is second to none. For example, world scrap recovery during the preceding 4 years averaged just under 2,300,000 metric tons per annum, and at an average price of 70 ¢ a pound, this works out at a turnover of about $3.5 billion, which indicates that the copper scrap industry, or recycling as it is now becoming known , is a substantial one.

Jan 1, 1977

By Mike Broczkowski, Laura Dewhirst, Kieran Large, Angelo R. Fernando, Heather Daigneault, Jim Johnson, Randy Wiens

The radioactive isotope radium 226 is a contaminant of potential concern in effluent waters from metal mining operations in Canada. Acceptable release levels of radium 226 are governed by Metal and Diamond Mining Effluent Regulations. Since radium is invariably present as a companion element in uranium ore, monitoring and controlling of radium 226 is a must for uranium mining operations. Measurement of radium 226 is traditionally carried out through a radiochemical technique involving selective co-precipitation of radium with barium sulphate followed by alpha spectroscopy for quantification. As of 2010, Cameco has also been using an ICP-MS based radium analysis method developed in collaboration with a research team at Trent University, Peterborough, Ontario. This method, which is highly automated and requires significantly less sample handling, with improved turn-around-times, is being used by Cameco site laboratories at the McArthur River and Cigar Lake mines as well as the Port Hope Conversion Facility. This paper compares the benefits and drawbacks of this new method, compared to the traditional alpha counting procedure drawing from almost ten years of field experience.

Jan 1, 2020

According to the principle of similarity, the physical and chemical configurations of a system can be defined by ratios of magnitudes within the system and do not de-pend on the size or nature of units of measurement. In the present work, the similarity principle was utilized in evaluating the reducibility of various iron ores in a rotary batch furnace under optimum operating conditions. It was then used successfully to extrapolate the results, first to the operation of a 20-ft. pilot-plant kiln and then to an industrial-size 80-ft. kiln. By means of this systematic analysis of kiln operation, it was possible to increase the production capacity of the kiln considerably. T HE kilns used by the Strategic-Udy process for the partial reduction of iron ores are, in most aspects, similar to conventional calcining kilns. Iron ore is fed continuously in the upper (feed) end of the kiln and, as the latter rotates

Jan 1, 1964

By H. F. Maulson

For the benefit of those who are not familiar with the history of the western Provinces-Manitoba, Saskatchewan, and Alberta-as regards our natural resources, a few words of explanation may be in order before taking up the consideration of the Mines Act of 1930. In 1867, The British North America Act was passed by the Imperial Parliament. That Act, which is our constitution, created a union between the provinces of Nova Scotia, New Brunswick, and Upper and Lower Canada (now known as Ontario and Quebec respectively) under the name of the Dominion of Canada. Provision was made therein for embracing other parts of Canada from time to time. That portion of Canada which today comprises the Provinces of Manitoba, Saskatchewan, and Alberta and the lands to the north of them, was then known as Ruperts Land and the North West Territory. In the year 1670, King Charles II had granted by Letters Patent to Prince Rupert and his associates, known as ?The Governor & Company of Gentlemen Adventurers of England, Trading into Hudson's Bay?, commonly known as the Hudson's Bay Company, the lands and territories therein described, being roughly all the lands adjacent to and west of Hudson's bay; also the gold and silver to be found or discovered therein and other rights as more fully described in said Letters Patent. The land so granted was called 'Ruperts Land'.

Jan 1, 1930

By R. N. Chakravorty

Environmental monitoring plays a key role in coal mine safety. In recent years, significant advances have been made in the development of systems suitable for monitoring air in underground coal mines. Because of intensive mining and large capital outlay, the need for higher productivity consistent with safety is well recognized and it appears that environmental monitoring may help achieve this objective. This paper reviews the state-of- the-art in the monitoring technology with particular reference to hazardous gas detection in underground coal mines. The preliminary results obtained from ongoing studies, with regard to continuous monitoring of methane and carbon monoxide in mine air in some of the operations in Western Canada, are discussed. The inadequacies of the methods using spot samples are examined and the need to supplement the present practice with continuous monitoring systems is emphasized.

Jan 1, 1979

By I. Southern, S. Kelebek

"Smelting furnace bricks contain significant quantity of base metals trapped in refractory material. A series of flotation tests were carried out on samples of old bricks from Sudbury area to examine upgrading behaviour for recycling purposes. Depending on the grind size used nickel recoveries varied from 60 to 90.6% with corresponding grades of 20% and 14.7%Ni. There is a trade-off between nickel and copper. The nickel has responded well to fine grinding, however, the copper recovery suffered from it. Mineralogical characteristics and flotation behaviour of the brick material are discussed in reference to those from the primary ore. INTRODUCTIONMineral processing is well recognized as a mature technology not only for the mining industry, but also for the environmental industry for the purpose of remediation and recycling. Materials available for recycling are usually the products of many years ago. There are multiple stake holders in this area. In general, when the processing results in a product that can be reused or sold, the company carrying out the remediation makes a profit, while the regulators and the public are pleased due to a cleaner environment. From these points of view, there have been many papers published over the years on various mineral processing techniques applied to separation of many different materials including from mining and metallurgical industries (Wilson et al., 1994; Tsunekawa et al., 2005; Saikia et al., 2012).Flotation may be viewed as the backbone of the mining and metallurgical industry since its invention for separation of solids from one another almost a century ago. It is capable of recovering a variety of finely divided different solids following their liberation from each other. Its versatility and highly competitive nature in terms of cost per tonne of material processed, accounts for its occasional uses in the environment engineering area. In the mining industry, flotation is the standard method used for the sulphide ores. It can be applied as a bulk flotation and/or differential flotation. Bulk flotation, which refers to co-flotation of several components from their source, is most suitable for environmental cleanup objectives. Desulphurisation of various plant tailings is a typical example of this (Benzazzoua et al., 2000)."

Jan 1, 2012

Cansolv® S02 Scrubbing Technology was described in a paper in Copper/Cobre 03. Four years on, the technology is operating at a full scale production facility.Hindustan Zinc Limited expanded their capacity by installing the AUSMELT process. The process proceeds through smelting, slag reduction, slag cleaning and holding stages sequentially in the same vessel, resulting in widely varying off gas characteristics. The off gas is suitable for treatment is a conventional acid plant for a modest proportion of the day, but at other times produces off gas too high in S02 to be discharged to atmosphere. Cansolv® S02 Scrubbing Technology was identified as a means of effectively removing the S02 down to low levels from the off gas during all stages of the pyrometallurgical process. Furthermore, the Cansolv® S02 Scrubbing System Technology produces high purity S02 that allowed for the captured S02 to be directed to an existing acid plant, avoiding the capital cost of new acid making capacity.

Jan 1, 2007

By Bruce A. McFarlane

"I WOULD LIKE TO SAY how honoured I am that I have been invited to participate in this panel discussion. I have taken the liberty of narrowing my topic somewhat so that instead of speaking on the Sociology of Professions as a whole I will speak on one aspect of it, that is, on Manpower Problems in the Minerals industry of Canada, with some reference to a new social role for the professionals engaged in this industry. This probably means that I will be encroaching on areas covered or to be covered by other speakers, but I hope that when I do so I will do so from a slightly different vantage point. That is, from a sociological perspective rather than from a historical, industrial, business or professional perspective. I plan to divide my discussion into three areas, namely: (i) problems of ownership and control; (ii) environmental problems; and (iii) manpower and recruitment problems. I do not plan nor am I able to provide clear-cut solutions to the various problems I raise under these three headings. Rather, I hope that my discussion of the problems may form the basis for an extended discussion here and elsewhere. Because of the limitations of time, I will only briefly discuss the first two problem areas noted above – (i) ownership and control and (ii) environmental problems - and I plan to concentrate on the manpower issue."

Jan 1, 1972

By M. Myllymäki

"Pre-treatment of mill feed in a minerals processing plant enables for higher production efficiency per ton of product, reduction of consumables and diverting mineral feed types. Sensor based particle sorting allows for pre-concentration of the run-of-mine (ROM) material prior to other concentrating process. Various sensors provide different responses from the minerals in measured particles. The capability of “accepting” or “rejecting” particles based on sensor responses is investigated in specific test work for each project. Modern sorting machines use pneumatic actuators to divert the reject particles from the material stream. This paper discusses the incorporation of ore sorting test work in processing and plant design. When taking the effects of a sorting circuit into account early in the process planning phase, the downstream process can be adequately sized and impacts evaluated. Potential benefits include but are not limited to increased head grade, lower tonnage to the mill, increased mining operations, removal of deleterious elements and changed properties in the process feed. In a case study we present the Keliber lithium project in central Finland. The plant will produce 9000 tons of lithium carbonate per year from a spodumene ore. Ore sorting and flotation tests were carried out in laboratory and pilot scale. Process models were designed and simulations performed using Outotec’s HSC Chemistry Simulation software. Changes in the flotation performance (grade, recovery, impurity levels) were simulated with and without the pre-concentration of the ROM material. The metallurgical performance and mine economics of the different operational scenarios were evaluated using the Ore-Met optimizer module of the simulation software.INTRODUCTION Challenges in the recent years such as declining ore grades, increasing energy prices, scarcity of water and increasing environmental regulations raise the demand for more efficient processing technologies. Sensor based sorting offers a method for pre-concentration or waste rejection at an early process stage. The technology analyzes each rock particle separately for their unique physical and chemical properties, and diverts the particles into separate material streams by high pressure air jets. Successful implementation relies on ore heterogeneity, differential sensor response and suitable feed preparation."

Jan 1, 2018

By F. Rivard, M. G. Drouet, W. S. Ruff, P. Carabin

"In both the hot rotary-salt-furnace (RSF) treatment of aluminum dross and the cold ball-millsieving (BMS) treatment of zinc dross, enormous amounts of energy and recoverable metal are wasted and large amounts of greenhouse gas are produced. Such wastes and the environment pollution could be avoided by using the DROSRITE PLUS™ technology. Economic and GHG production comparisons between the presently used industrial treatment processes and DROSRITE PLUS™, supported by over one hundred tests conducted in Canada, the US and Europe, are presented. The savings, with DROSRITE PLUS™, would be about $191 and $418 per MT of aluminum and zinc dross, respectively.INTRODUCTIONDross is a material, which forms on the surface of molten non-ferrous metal, such as aluminum or zinc, during melting, metal holding and handling operations when the molten metal is in contact with a reactive atmosphere. Dross normally consists of metal oxides entraining a considerable quantity of molten free (unreacted) metal, and for economic reasons it is desirable to extract the free metal before discarding the residue. In the case of aluminum dross, recovery of the metal is usually carried out by treating the dross in a furnace at a high temperature (Peterson et al., 2002). By contrast, cold zinc dross is crushed in a ball mill followed by sieving to separate the coarse metal portion from the fine oxide residue.The conventional aluminum dross treatment process, using gas or oil-heated rotary salt furnaces (RSF), is thermally inefficient and environmentally unacceptable because of the salt slag and CO2 produced from the combustion of fossil fuels. In the past several years, a number of salt-free processes have been developed and some of these have found limited commercial use (Gripenberg et al., 1994; Lavoie et al., 1990). In all these dross treatment processes, heating of the cold dross in a rotary furnace requires an external energy input that varies between 375 and 2,500 kWh per (metric) tonne of dross. Molten metal separated during processing of the heated dross is tapped, and the remaining solid residue is discharged from the furnace."

Jan 1, 2012