Search Documents

By A. J. Hyett, R. D. Reichert

"A laboratory and field research program was conducted to investigate the major factors influencing bond capacity of grouted cable bolts. The results indicate that cable bolt capacity most critically depends on the grout uniaxial compressive strength (UCS), the radial confinement, and the embedment length.In the laboratory &apos;split-pipe&apos; tests were conducted using P VC, aluminum and steel pipes to provide radial confinement, and field test sites were chosen in granite, limestone and shale rock masses. For both datasets higher capacities were obtained under conditions of higher radial confinement. A correlation between the two was obtained through a comparison of the radial wall stiffness of the laboratory pipes with that of the field boreholes as measured using a high pressure dilatometer. Cable bolt capacity was found to increase with embedment length though not in direct proportionality.The use of low water cement ratio grouts (<0.40) can increase cable bolt capacities by 50% to 75%. This effect is maximized under conditions of high radial confinement. However, the use of super thick grout paste (0.30 and less) may be both impractical and undesirable, first because of their limited pumpability and second because of their inconsistency in strength. Grouts with a water cement ratio of between 0.35 and 0.40 are recommended for practical cable bolt applications."

Jan 1, 1992

By L. T. Raevskaia

We discuss the stability problem of a piston of the reversible axial-piston pneumatic motor called DAR-14M. We performed the full analysis of stress and deformation characteristics of the piston near a resonant frequency with the help of FEM ANSYS. We estimated the own frequency of the piston analytically for the given motor, this estimate was confirmed numerically in the model analysis FEM ANSYS. It was also shown in harmonic analysis that loaded piston end behaves very different in comparison to the unloaded end. As expected, maximum deformation was found in the area of the holes of the bearing shaft, indicating an optimization necessary in that region of the motor.

Aug 1, 2013

By Joseph Bradley

THROUGHOUT this article, minerals used in the paint industry are designated &apos;pigments&apos;. They may be classified in two groups: (1) Pigments which are used in the state in which they occur in nature, requiring only mechanical preparation. (2) Pigments which require heating or chemical treatment before use, in order to obtain from them a product of the desired quality or shade of colour. They may be further classified according to colour, as follows: White Pigments .-These include calcium carbonate (chalk, marble), gypsum and alabaster, kaolin-or china-clay, and magnesia. However, the white pigments most extensively used are compounds prepared chemically from minerals containing lead, zinc, titanium, and antimony. The white pigments are of particular importance because, not only are they used by themselves, but they also serve as adjuncts to other colours for the production of special shades. Yellow Pigments.-These are mainly naturally occurring ferric hydroxides, as limonite and bog iron ore, or similar. compounds prepared artificially. Brown Pigments .-Pigments of this group are distinguished for their beauty and depth of colour, and many of them are used in the finest of paintings. Familiar names are sienna, umber, and Vandyke brown. They are for the most part ferric hydroxides, containing varying amounts of water; but the group also includes a manganese brown, which consists chiefly of a mixture of oxide and hydroxide of manganese. Red Pigments.-Chief among this group is ferric oxide, known under various trade-names, such as Canadian red, Persian red, etc., and also the much prized and somewhat rare vermilion. The pigment used is either naturally occurring hematite, de-hydrated limonite, or artificially produced red ferric oxide.

Jan 1, 1937

By C. M. Campbell

In his report on the Coal Resources of Southern Vancouver Island, Mr. J. D. MacKenzie stated that: "For various reasons it has been imagined that the coal deposits of Vancouver Island are extremely large and readily available." "Unfortunately," he added, "neither of these assumptions is correct." The chief disability under which the Island mines now labor does not concern the extent of the deposits. There is ample coal for the present demand. It does, however, concern the availability of the coal. If it were readily available the fuel-oil competition would not be serious and there would be no competition with Alberta, American, Welsh, or Australian coal along the Pacific Coast, for Vancouver Island coal could be produced at a price that would cut out all competition. The outstanding operating difficulty common to all Island mines is the extreme irregularity of the coal seams. To most people a coal seam is synonymous with uniformity, and in most coal seams a condition found at one point will be repeated at other points in the same seam throughout the basin. The accompanying drawings show how very far this is from being true in the Cassidy mine, which, in many respects, is typical of Vancouver Island mines. Figure I is a plan covering about 160 acres of the Douglas seam, the only workable seam in this part of the district. The area shown represents what has been the best producing part of the mine and indicates the very large percentage of the seam where the coal is either entirely lacking or so small in amount that it cannot be profitably recovered.

Jan 1, 1924

By R. M. Bustin

"Extensive deposits of tectonically sheared coal of the Mist Mountain Formation occur in the south eastern Canadian Cordillera. The quality of the coal varies markedly; it is commonly partially oxidized and poor washability characteristics.Oxidation of the sheared coal has been promoted by its fine grain-size and by fractures in adjacent rocks which have facilitated penetration of atmospheric oxygen and circulation of oxygenated waters. Oxidation has resulted in a loss of coking power, a decrease in vitrinite reflectance, and an Increase In oxygen and decrease in carbon content.The relatively low clean coal yields of the sheared coal are primarily the result of the greater volume of mineral matter present, which in turn reflects both the greater susceptibility to shearing of coal with abundant rock partings and the shearing and dissemination throughout the coal of formerly discrete rock partings. The high ash content of some sheared coal seams may be artificial, resulting from the difficulty in distinguishing and separating sheared roof rock and floor strata from the coal seam during mining. There is little variation between the quality of the washed sheared and unsheared coal, with the exception of the somewhat higher ash content of the clean sheared coal compared to clean unsheared coal. This poorer separation of the ash from the organic fraction of the sheared coal is considered to be a product of the large amount of fines present as well as the local formation of aggregates of organic material and ash resulting from plastic flowage of the vitrite and clarite during shearing.IntroductionIn the southeastern Canadian Cordillera, coal seams of the Lower Cretaceous Mist Mountain Formation (Gibson, 1979 were in part sheared and comminuted during Late Cretaceous and Tertiary tectonism . Extensive deposits of sheared coal exist, and even in areas of mild deformation the coal may be locally sheared (Bustin, 1979). The quality of the sheared coal varies notably; it is commonly oxidized even far from the present weathering horizon, and locally has a disproportionately large amount of ash and poor washability characteristics even far from the present weathering horizon and locally has a disproportionately large amount of ash and poor washability characteristics."

Jan 1, 1982

By C. Caballero, M. Rosales, C. León, A. Valencia, R. Fuentes, A. Moyano

Slopping is the formation of waves in the converter due to the gas injection by tuyeres. Those waves produce a premature wearing of the refractory lining of the reactor due to its great amplitude. The affected zones are the tuyere line (outlet gas from tuyeres) and the front of this line. In the present work, a theoretical and experimental study is made to develop a theory that determines the variables involved in slopping, characterizing the more important parameters of operation in the phenomenon of slopping. In addition, this theory will allow for determination of new technological alternatives of the blast injection permitting to depress the slopping phenomenon.

Jan 1, 2007

By Richard Q. Fox, Joe L. Pinson

This paper provides guidelines jo1• analyzing and selecting electric power demand controlled. Error calculations, load selections and timing criteria are identified as the three key functions which affect the suitability of a demand controller for any particular application. The advantages of simulating the demand control application on a computer are described, and applications of a demand controller to an iron ore concentrator and a copper refinery are shown. Finally, the paper studies the return on investment for a demand controller.

Jan 1, 1976

By W. V. McKnight

The paper discusses the equipment and methods used to establish some of the characteristics of a braking system. Some typical tests are described and an explanation of the approach used to derive information from the recorder charts is given.

Jan 1, 1966

By The Staff

Introduction In this paper it is proposed to discuss briefly some of the problems confronting the management of a gold mine in choosing a method of milling to recover the gold from various classes of ore. In order to simplify the discussion, the more common types of gold ores are classified from a metallurgical point of view as follows: Class 1?A: Free-milling ores which require only relatively coarse crushing. B: Free-milling ores which require finer grinding to release the gold. Class 2?A: Gold ores which contain the gold partly in the flee state and partly associated with a small amount of iron sulphide, and which do not require fine grinding. B: Gold ores similar to 2A, but which require fine grinding. Class 3?A: Gold ores containing copper in quantities insufficient to interfere to a serious extent with cyanidation. Gold ores containing copper in sufficient quantity to interfere with cyanidation but in which a large proportion of the gold is in the free state, the remainder being chiefly associated with the copper mineral, chalcopyrite. Gold ores containing copper and other sulphides, such as pyrite, etc., in which the gold is principally associated with these sulphides.

Jan 1, 1931

By Oscar F. Tangel

This paper outlines Canada&apos;s current status in world iron ore markets, and evaluates t he prospects for the future. Estimates for the production, export and consumption of iron ore are given. Canada&apos;s major market will continue to be the United States, with the European Common Market countries, Japan and the United Kingdom also forming important outlets. The advantages held by Canada&apos;s major competitors in these latter three market areas are briefly discussed

Feb 1, 1966

By Oscar F. Tangel

This paper outlines Canada's current status in world iron ore markets, and evaluates the prospects for the future. Estimates for the production, export and consumption of iron ore are given. Canada's major market will continue to be the United States, with the European Common Market countries, Japan and the United Kingdom also forming important outlets. The advantages held by Canada's major competitors in these latter three market areas are briefly discussed.

Jan 1, 1966

By W. H. White, A. J. Sinclair

"Unaltered biotites from three samples of monzonite and gabbro from the Copper Mountain stock and a single sample from a pegmatic biotite-chalcopyrite vein cutting the Triassic Wolf Creek formation have a mean K-A age of 193±7 m.y. These data support a suggestion based on geological evidence that Copper Mountain ore deposits are related genetically to the Copper Mountain stock.A cogenetic mineral pair (biotite and clinopyroxene) from a sample of sericitized and chloritized monzonite of the Copper Mountain stock have identical K-A ages of 150 m.y., which probably represents a time of wide-spread, post-ore, hydrothermal alteration. This alteration is believed to be related genetically to a group of post-ore intrusions known as the ""mine dykes,"" suggesting that they also have an age of 150 m.y."

Jan 1, 1968

By N. Saracoglu, R. H. Wallis, J. E. Betz, F. L. Jagodits, B. R. Krause

"Geophysical test surveys were conducted with various methods (EM, lP, gravity and magnetic) over the McClean uranium deposits of the Canadian Oxy- lnco Joint Venture. The result s were assessed to judge the contribution each method might make toward further discoveries of graphite-associated uranium occurrences.The best drill targets have proven to be discontinuities in graphitic conductors and locations where the tatter are intersected by fracture zones in the Athabasca. The tests demonstrated that the preferred combination of geophysical survey s is horizontal loop EM to locate graphitic conductors in the basement and VLF-EM to locate the fractures.IntroductionThe discoveries of the McClean North and South uranium deposit s (Fig. 1) are essentially geophysical successes resulting from drilling MaxMin delineations of INPUT airborne electromagnetic responses (Saracoglu et al., 1983). After the initial discovery in 1979, various geophysical methods, techniques and instruments were employed to test their effectiveness in this environment and to guide exploration for other deposit s of a similar nature in the remainder of the 260 km2 property.The McClean uranium deposits lie below 150 m to 180 m of overburden and Athabasca Group. Radioactive signatures might be expected; however, the Athabasca Group acts as a barrier to radioactive emanations. Fortunately, the uranium mineralization is associated with graphite in the crystalline basement. Prior drilling of ground electromagnetic anomalies confirmed that EM surveys could locate and out line basement graphitic conductors. However, as there were many anomalies, most of which could not reasonably be expected to be associated with uranium , there was need to identify additional parameters, related to mineralization, which could be detected geophysically and used to narrow the search."

Jan 1, 1986

By G. Plascencia, C. López, J. González, D. Jaramillo, M. A. Barrón

Air jet and molten matte interaction within a Peirce - Smith converter is analyzed during the first stages of blowing using Computational Fluid Dynamics (CFD), by means of the Large Eddy Simulation and Reynolds Stress turbulence models. Jet velocities ranging from 5 to 150 mis, which involve the bubbling and open jet regimes, were considered in 2 and in 3-D numerical simulations. As a result of the computer simulations, it was found that low velocities results in gas bubbling in the molten copper, whereas higher gas velocities results in well defined plumes. The consequence of such different behaviours results in an increment in the rate of refractory wear or in copper splashing respectively. The analysis of the results may lead to improve the design of the tuyeres currently used in copper converting. Bottom blowing of air is also explored in this work. Numerical results show a strong non-linear parabolic behaviour of the jet velocity on the average velocity of copper; which means that beyond certain jet velocity, the copper de-accelerates thus reducing its velocity. This may be due to the open nature of the jet, which prevents the momentum transfer from the injected gas to the molten copper.

Jan 1, 2007

By Yves Bellemare

Entre 1983 et 1997, l'exploitation de la pierre de taille au Québec a été marquée par l'émergence et la consolidation de plusieurs nouvelles variétés de granit, provenant exclusivement ou presque de la Province de Grenville. Le Québec demeure toujours le principal expéditeur canadien de granit dimensionnel, avec des expéditions annuelles représentant près de quatre-vingt-dix pour cent des expéditions totales canadiennes de granit brut et transformé. La production annuelle de granit brut oscille, depuis 1994, autour de cent mille tonnes métriques. Cette production a plus que doublé de 63 000 à 140 000 tonnes métriques entre 1981 et 1990, mais elle a connu une chute importante en 1991 (67 000 tonnes métriques); cependant depuis 1994, elle est en forte progression (Ménard, 1998). En 1983, le granit dimensionnel était extrait de plus de vingt-cinq carrières, dont les trois quarts se localisaient dans la Province géologique de Grenville. Comparativement, en 1997, le Québec comptait trente-sept carrières actives, dont trente-cinq dans le Grenville (Gaudreau et al., 1998). Cette concentration des carrières dans la Province de Grenville s'explique par la demande accrue de nouveaux produits au fil des ans et par le potentiel élevé de découvertes de nouvelles variétés dans cette Province géologique. L'accessibilité au territoire, toujours plus grande, a facilité la mise en production de carrières favorisant la diversification des produits. Le ministère des Ressources naturelles du Québec (MRNQ) a consacré depuis 1980, beaucoup d'efforts dans la recherche de nouveaux gisements et de nouvelles variétés. En plus des programmes de subvention destinés aux prospecteurs ou aux compagnies, le ministère a réalisé des campagnes d'inventaire de pierre de taille, de pierre concassée et de pierre d'enrochement pour en connaître le potentiel géologique et à orienter les recherches futures (Nantel, 1983; Nantel et Martignole, 1991; Bellemare, 1995a, b, c, d, e, f, 1997, 1998a and b; Bellemare et Petryk, 1996a, b, c and d). Cette étude donne un aperçu des différentes variétés de pierres extraites dans la Province de Grenville entre 1983 et 1997, les situe dans leur contexte géologique et en localise les principales régions productrices. Elle est une suite à l'article publiée par Nantel (1984).

Jan 1, 2001

By I. C. Edwards, D. C. Smith

THE milling plant of Bicroft Uranium Mines Limited at Ban-croft, Ontario, was one of the first in Canada to employ ion excl1ange for the selecti1•e recovery of uranium from acid leach liquors. The ion ex-change circuit started operating early in November, 1956, and by June 1 I959, had handled more than two million tons of pregnant solution containing I,830,000 pounds of U3Os. Each column had been saturated and eluted about 430 times. The ion exchange columns are the conventional fixed bed type. Uranium is eluted from the resin with a sodium chloride-sulphuric acid solution and is precipitated continuous-ly with magnesia. After filtering and drying, the precipitate, or "yellow cake," is packaged in drums for shipment to the refinery.

Jan 1, 1962

By O. E. Andrew

THE object of this paper is to present a brief summary of the dust control system in use on the 3,825-foot level at the jaw crusher station, Lake Shore mine. During the years 1936 and 1937, dust survey reports were presented to the management showing that high dust concentrations were being created during operating periods. At that time, however, this crusher was running only an hour or so each shift, and it was felt that no large capital expenditure for dust control equipment could be justified. In order to afford some protection to the operators, a number of respirators then on the market were .tested and the &apos;Comfo&apos; respirator was adopted for use by the crusher-men. In 1938 this crusher began to handle a large share of the total mine tonnage and the hours of operation were increased. Further dust sampling showed increased dustiness with the longer operating time. It was also realized that the operators suffered considerable inconvenience if they wore their respirators throughout the shift. If the respirators were not worn, then dangerous amounts of dust were being inhaled. The fact that the crusher station was situated on the 3,825-foot level limited the means that could be employed to eliminate the dust hazard. At that rime there was not available the 5,000 c.f.m. of fresh air which would be required to sweep out or dilute0 the dust, and there was also no way of disposing of the contaminated air without passing it on for other men to breathe. Thus it became apparent that a self-contained dust disposal system would have to be installed.

Jan 1, 1941

By A. Haque

"This paper describes an improved formulation of an analytical shear strength model developed by Haque & Kodikara (2012) by incorporating the failure of regular concrete/rock joints subjected to CNS condition. Sokolovskii’s analytical solutions developed for failure stress of slopes have been found to be effective in this regard. The analytical models have been validated for predicting the shear behaviour of concrete/rock joints subjected to various CNS loading conditions. The model has been found to accurately predict the dilation, normal stress and shear stress behaviour for a regular triangular saw-tooth joint up to the peak shear stress. Moreover, the peak shear stresses of concrete-rock joints with asperity angles ranging from 5 to 27.5o compared reasonably well with the available laboratory test results.INTRODUCTIONA new shear strength model for elastic regular triangular concrete/rock joints loaded under Constant Normal Stiffness (CNS) boundary condition has been developed by Haque & Kodikara (2012). The salient feature of this model is its capability of accurately estimating the normal and shear stresses of joints with shear displacements under CNS condition by incorporating the elastic deformation of asperities. However, the shear strength model of Haque & Kodikara (2012) for the elastic asperities cannot be directly employed to predict the peak shear stress of a joint experiencing plasticity under applied loads. Therefore, the model inevitability requires articulation of an appropriate shear failure criterion simulating the boundary conditions of the loaded asperity to predict the peak shear stress and corresponding normal stress and dilation behaviour of concrete/rock joints. Sokolovskii (1960) developed a set of analytical solutions for failure stress of slopes comprising c-??soils, which can be exploited effectively to simulate the failure condition as encountered for loaded regular triangular concrete/rock joints (Seidel & Haberfield, 2002)."

Jan 1, 2015

By N. Fukatsu

The recent development of galvanic cell-type hydrogen sensor for molten copper was outlined. The principle of the sensing mechanism, the fundamental structure of the sensor, and its performance as a process control device are discussed based on experimental work undertaken by the authors. Besides sensors based on usual perovskite-type proton conducting oxide, those using magnesium-doped alpha alumina, which was recently known as a proton conductor, were investigated and the results at the laboratory scale are reported. Considering the excellent sensitivity at high temperature and the stability to the disturbance from the attendant oxygen activity, magnesium-doped alpha alumina was regarded to be a superior material for the sensors used for such purposes.

Jan 1, 2007

By Mohamed Sassi, I. Kolo, R. L. Sousa, R. K. Abu Al-Rub, Manhal Sirat

"Fractures induced by folds are pivotal in hydrocarbon exploration, ground water transport and harnessing of geothermal energy. This is because of the need to predict and understand fracture propagation in reservoirs which have folded rock formations. Despite its prominence, there is a lack of reliable numerical models for simulating fractures resulting from rock folding. This is partially due to the difficulty involved in fracture modelling. As a contribution to fold-fracture modelling, this work applies a coupled plasticity-damage model to rock fracturing and anticlinal folds. Parametric studies on a single folded layer give insight into the fold formation and behaviour. The anisotropic continuum damage model which considers both tension and compression is formulated using the power damage evolution law. For ease in formulation, strain equivalence hypothesis is adopted whereby the strain is the same for both damaged and undamaged configurations. Lubliner plasticity yield criterion is adopted for plastic deformation. The model is coded in Abaqus user subroutine UMAT and is applicable to quasi-brittle materials.INTRODUCTIONThe understanding of fractures in the earth’s crust helps in the prediction, evaluation and characterization of fractured reservoirs, whether they are petroleum, geothermal or underground water reservoirs. This is partly because reservoir permeability and stability are dependent on fracture properties (Nelson, 2001). To achieve this, various approaches have been developed to analyze reservoir rock fractures. These could be grouped into (a) discrete approaches – where the rock mass is represented by a finite number of well-defined components and (b) continuum approaches – where the mathematical assumption of an infinitesimal element is made (Jing, 2003). Ivanova (Ivanova, 1998) comprehensively studied fracture systems in nature and highlighted folds as one of the major geologic settings that produce fractures. Naturally occurring folds in reservoirs sometimes compound fracture analysis. It might not be clear whether the fractures formed before, during or after rock folding. Fractures formed during the folding process are expected to show stress orientations related to folding and are thus of primary concern in rock folding simulation. It could be argued that there are no numerical models that as"

Jan 1, 2015