Search Documents

By E. Demedde

Carbon anodes in aluminium reduction cells are continuously consumed during electrolysis. In prebake cells the anodes are replaced at regular intervals. The spent anodes, called butts, are often allowed to cool in air while emitting fluorides into the building from the hot alumina cover and the adhering bath. In modem smelters spent anodes are placed inside enclosures and fluoride emissions during cooling are effectively reduced. Fluoride emissions from spent anodes were estimated by considering the kinetics of fluoride formation, a heat transfer analysis of the cooling anode butt and the ventilation flow from a cavity. Fluoride emissions from large anode butts cooling inside enclosures were compared with those cooling in air. Good agreement with published experimental values was obtained for enclosures having different leakage opemngs, when a hydrofluorination reaction of the spent anodes was included.

Jan 1, 2006

By J. R. Johanson, A. W. Jenike

"A solid flows out of a bin provided that the outlet is sufficiently large so that stable obstructions to flow do not develop. The geometry and surface finish of a bin and the construction of the feeder determine the type of flow pattern which then develops within the bin. The pattern, in turn, affects the uniformity and consistency of the stream, segregation, caking, degradation, live capacity and the action of level measuring devices.In most bins now in operation, material flows toward the feeder through a channel which forms within the stationary solid. This is referred to as funnel flow. If the hopper of the bin is sufficiently steep and smooth and the feeder capable of drawing material across the whole area of the outlet, all the solid flows whenever the feeder is in operation; this is referred to as mass flow. Mass-flow bins are usually far superior to funnel-flow bins; their initial cost is also usually higher.The paper describes the design criteria used in deter-mining the minimum bin outlet needed for flow and the bin geometry needed for mass flow."

Jan 1, 1970

By K. Ogawa, T. Yokoyama

Hydraulic fracturing technique, an applied technique to cause tensile fractures to rock by injecting water pressure to a certain closed section of the borehole, is a measurement method of in-situ rock stress. This technique has the highest track record for techniques used in sub 1000 meter. A feature of this technique is comparatively simple and easy for in-situ stress measurement, because the measurement is applicable when a drilled borehole is available. The predominant advantage of this method is that elastic constants such as Young’s modulus and Poisson’s ratio are not required for determining the value and direction of initial stress. The factors to determine the stress state are the water pressures of re-opening and shut-in of fractures around the borehole wall and its directions. With conventional methods, however, the accuracy of the derived stress states from the observation equations was often adversely affected by the lack of consideration of the remaining water pressure in fractures and insufficient stiffness of the pressurization system. We have developed a new hydraulic fracturing system based on a new test method concept overcoming these defects, and applied to a 300 meter deep borehole in granite. The most important improvement of the new system is an employment of a syringe pump which enables an accurate flow control of fluid with less than 1ml/min in the pressure of 30MPa. Therefore the new test system has a quick response for pressurising in the interval zone, and the measured data was confirmed extremely accurate.

Jan 1, 2015

By J. B. McKenzie

Since connnencing underground prcxiuction in 1979, the Ruttan Mine has been prone to secon:iacy sulphide dust explosions. Al though infrequent during the early years of prcxiuction, these occurrences did result in major damage and lost time injuries. 'As the mine exparrled and developed to further depths, sulphide dust explosions occurred on a more frequent basis. Incomplete ventilation se:rvices, required to exhaust the affected areas, caused frequent delays resulting in lower prcxiuction rates due to the time required to ventilate the affected areas of the mine. CUrrent procedures to minimize the effects of secon:iacy dust explosions evolved from practical suggestions arrl examining methcx:ls other mines have developed to cope with the problem. Procedures and regulations to protect errployees from exposure to hazards of sulphur dioxide are time consuming, expensive and counter prcxiuctive in their present fonn. This paper describes the history of secon:iacy sulphide dust explosions at the Ruttan Mine and the methcx:ls and proced.ures currently in place to minimize and contain the effects of dust explosions.

May 11, 1988

By William H. Emling

With profitability pressures in heavy industry increasing, many producers are turning to predictive maintenance as a means of harvesting untapped value from their production assets. Corporations are losing their maintenance and processing core competencies through attrition. As capital budgets are being trimmed, manufacturers are consolidating operating units into fewer, more profitable routes. Maintenance functions, however, typically receive low priority when investment is made, since many companies consider maintenance costs as ?overhead?. Condition-based monitoring, integrated to Level I and Level II process inputs, is seen as the most cost-effective solution to the implementation of predictive maintenance strategies. This paper will review the evolution of preventive and predictive maintenance programs, highlighting examples of successful application of integrated condition monitoring.

May 1, 2001

By LUKE O. LINDOE

A major clay products industry in the Medicine Hat area since before 1910 has maintained a continued interest in the clays of the Cypress Hills. For the first forty years the materials used were local red-burning Cretaceous and Pleistocene clays and sands and high-quality stoneware clays of the Whitemud Formation at Eastend, Saskatchewan. Recently a much broader spectrum of raw materials has been brought into use. Including the exposures of the Eagle Butte structure, the Cypress Hills present a 1200 m section of clay-like sediments. Of this 1200 m about 94 per cent, the high montmorillonite shales of the Upper Cretaceous, can be considered useless, or nearly so; the remaining six per cent, all fresh-water beds, presents a wide variety of potentially useful materials. The development of these clay resources is complicated by deep surface creep on the south flank of the Cypress Hills, by largescale slumping on the north flank and by a structural complex in the Eagle Butte area.

Jan 1, 1984

By P. M. Pearson

This paper describes the principles ()f systems engineering and their application to the various transport problems confronting the mining industry. The organization of mining operations into sub-system design problems is explained.

Jan 1, 1970

By F. Hassani, J. Peck, D. J. Lucifora

The performance of a rotary blasthole drill is heavily dependent on the material being drilled. This material is a microcosm of the in-situ geology that makes up the surface mine in which the rotary blasthole drill is deployed. The performance metrics that are influenced by the in-situ geology are penetration rate (distance drilled per unit time), rotary torque and to a lesser extent rotary speed and vibration. For simulation and testing purposes it is useful to have a validated plant model based upon the application of study. Once validated, a plant model can be used to perform simulation based testing as a supplement and possibly in place of more expensive and logistically complex field testing. Previous studies in the field of rock mechanics have supplied proven models that relate the performance of a rotary blasthole drill to the material being drilled for a given rock type with a given drill bit. In this study, field based experiments were conducted in an active surface mine on a working rotary blasthole drill and the corresponding monitoring while drilling (MWD) data was recorded. Data analysis was then performed on the collected field data. The techniques used successfully fit the collected MWD data to the previously proven rock mechanic models. This paper explores the theory relating rotary blasthole drill performance to the material being drilled, illustrates the required data collection and data analysis techniques, and demonstrates the ability of these techniques and the known rock mechanic models to provide a simulated plant model for the drilling process that can then be validated. This validation is also discussed.

Jan 1, 2015

By P. J. Finnis

This paper describes the use of wire rope on open-pit mining equipment, giving specifications and examples of the performance achieved. Installation methods are also discussed, making the paper of considerable practical use to mine operators.

Jan 1, 1973

By D. R. Schmitt, N. Ong, R. S. Kofman

Shales and mudstones comprise about 75% of all the sedimentary rocks. In, particular, organic rich shales are considered as a petroleum source rock and more recently with the advent of hydraulic fracturing technology to be a reservoir in their own right. In this sense, the aforesaid motivates our work with laboratory measurements of elastic properties of these geologic materials, which are known to be anisotropic. As such, assuming Vertical Transverse Isotropy (VTI) symmetry, the dynamic and static moduli of a series of cores from various geological formations in Alberta, Canada are simultaneously investigated as a function of confining pressure using the ultrasonic pulse transmission method and strain gages. Dynamic moduli were obtained from ultrasonic P- and S-wave velocities measured on a prism cut with faces perpendicular, parallel and oblique to the assumed vertical axis of symmetry. Static moduli were calculated from strain-stress curves obtained along the directions perpendicular and parallel to the assumed axis of symmetry as well. Velocity measurements show that samples are highly anisotropic, but that the pressure-dependent behaviour of the wave speeds differs. VP(90°) and VSH(90°) both with layer parallel propagation and polarizations change little with pressure while VP(0°) and VS(0°) (both with layer perpendicular propagation) display significant nonlinear responses particularly at pressures < 25 MPa. These characters transfer to the derived full set of elastic constants. In order to effect a proper comparison of the dynamic and static moduli, we convert the dynamic elastic constanst to linear compressibilities pependicular (Kdyn1) and parallel (Kdyn3) which are directly comparable to the static tangent compressibiities obtained by differentiation of the observed strains. Both sets highlight the anisotorpic nature of the material but most interestingly Kdyn1 _ Ksta1 but Kdyn3 > Ksta3 by nearly 40% for one of the samples. The other samples measured respond similarly suggesting that conceptually the structure of such materials could be considered to be constructed of alternating stiff or compliant layers. This finding has implications in the response of the formation to stress particularly during hydraulic fracturing and the interpreation of acoustic logs in providing appropriate measures of elastic properties for engineering purposes.

Jan 1, 2015

By S. A. Bunk, E. C. Eccleston, J. J. Amsden

Fluidized bed technology has been widely applied to mineral and metallurgical processes. Over the years, modeling of fluidization technology has progressed to a level at which basic design parameters can usually be defined based on empirical correlations. In addition, scale-up considerations have become better understood, and significant advances have been made in the area of computer simulation. Despite these advances, fluidization is a complex phenomenon, and modeling tools remain limited in their ability to simultaneously model both fluidization and chemical process parameters. As a result, almost all mineral and metallurgical applications of fluidized bed technology require pilot testing prior commercial scale design. This paper outlines pilot plant testing requirements and process development considerations for development of low technical risk commercial designs.

Jan 1, 2011

By R. W. Nice

Presently about 60% of the world&apos;s nickel resources are tied up with lateritic ores while about 25% of the world&apos;s nickel is produced from sulphides. Based on this the industry has to focus on improving lateritic nickel economics in order to maintain the high use of the metal worldwide. In 1997 three junior mining companies in Australia organised finance against all odds and commenced development of three separate nickel and cobalt extraction plants treating lateritic nickel ores. All three projects utilise similar pressure acid leaching (PAL) technologies while each has unique metal recovery technologies All projects have experienced numerous processing and maintenance related difficulties such that full ore throughput has been reached by only one operation after five years. This shortfall in performance has caused the owners considerable angst and financial pain. In 2000 Cawse went into receivership and was purchased by an international corporation. Recently, Bulong also went into receivership and has undergone an orderly shutdown, awaiting sale to a new buyer. Murrin Murrin has settled with its financiers and is in a position to operate as planned for many years forward. This paper will discuss a number of the technical difficulties that affect the ore preparation, PAL and solution treatment circuits of these plants. The objective is to identify the cause of some of the difficulties and propose possible solutions so that the next generation of lateritic operations can emerge as technically and, more importantly, economic successes. A number of these process improvements have been identified by the existing operators and in many instances have been or are being implemented into the existing operations.

Jan 1, 2004

By W. Kempson

"As has been noted on numerous occasions, the vertical shafts being sunk around the world are all tending to get deeper as we seek to take advantage of higher grades of minerals which can sometimes be found at greater depths. One of the challenges with these deeper shafts is the requirement to supply services to the mine’s operations at depth as well as the requirement to dewater the mine. Both the supply of water and the dewatering of mines is generally done using piping. With the greater shaft depths, this piping is now required to contain higher pressures as well as to accommodate changes in temperature resulting from normal mine operations. This paper will discuss the requirements for the design of high pressure piping in deep vertical shafts. The discussion will start with the general definition of the systems and the detailed design requirement. Once this is clearly outlined, we will discuss the options available for fulfilling these requirement as well as the advantages and disadvantages of each of the systems. We will finish with the installation recommendations and provide a basis for the maintenance of these systems. INTRODUCTION Piping in vertical shafts is used to provide a number of services in underground workings. These services vary depending on geographical location and the type of the ore body which is being mined. For example, in the Zambian Copper mines, one of the largest requirements for in shaft piping is for dewatering. Similarly in the Gold deposits in the West Wits basin as well as the deep level Copper deposits in Arizona, one of the largest uses for the piping is the supply of a cooling medium to underground workings to create a safe working environment (this can in the form of water or of glycol depending on the application). In South Africa, systems were installed which used the hydrostatic head which is generated from supplying chilled water to mines whose depths exceeded 2,000 m below surface. This chilled water was supplied as a closed system, allowing for high pressures to be generated which was then used to supply useful work (for example, Rock Drills, Face Cleaning and other ancillary services) whose power was traditionally supplied by compressed air or electricity. This system was initially researched by Chamber of Mine in South Africa. The design pressure range of these systems is 14 MPa to 18 MPa."

Jan 1, 2019

By J. A. Espinosa-Guillen, J. A. Lopez-Molina, S. García, J. A. Valencia-Quintanar

"The design and implementation of grouting treatments in rock masses are procedures that require continuous adjustment of parameters and criteria to optimize the results. In this proposal we describe a set of tools that enhance decision-making for this type of jobs particularly in dam projects. The methodology is focused on hydrogeological zoning of the site and its constant update combining engineer’s experience with artificial intelligence techniques to integrate the site knowledge; as well as the evaluation of grouting results for different scrutiny scales, with special attention on the relationship between water absorption and grout consumption. INTRODUCTIONSeveral methodologies for design, implementation and evaluation for grouting rock masses have been developed for the solution of specific problems and tested in diverse geological conditions. Each of these methodologies is focused on results evaluation for different scrutiny scales (Table 1) and is employed to assist decision-making before or during the grouting process.Some methods define specifications for grouting each stage of the borehole, making theoretical, semi empirical or experience-based considerations to define basic parameters as maximum pressure, maximum volume, grouting time, flow rate, etc. Ultimately each approach aim to optimize the injection process, adjusting volumes or the grouting time required to obtain satisfactory results, reducing risk of creating new flow paths or unnecessary grout travels, and enhancing the mixture properties to achieve adequate penetrability and long-term behaviour. Some of these criteria have been widely used in dam projects, for example the concept of Grouting Based on Facts to define the maximum pressure and volume (Ewert, 1997), the GIN method (Lombardi & Deere, 1993; El Tani, 2012), or the North American standards based on Apparent Lugeon measures (Naudts, 1995; Bruce 2011); on the other hand, there are relatively new criteria that have shown good results for dam grouting as the Aperture Control Method (Bonin et al., 2012; Carter et al., 2012) or the Real Time Grouting Control Method (Stille et al., 2012)."

Jan 1, 2015

By Richard Murphy

"The general geology of the Great Bear Lake area has been described by; D. F. Kidd in the Summary Report of the Geological Survey for 1932. A brief description of the Eldorado mine was prepared by C. S. Lord for Memoir 230; Mineral Industry of the Northwest Territories; published by the Geological Survey in 1941. Recently; a detailed geological examination of the mine area has been initiated by the Geological Survey and; under A. W. Jolliffe's leadershif; J. D. Bateman; H. B. Thurber; and M. Feniak have prepared a number of maps and reports; as yet unpublished. Detailed mapping of the mine has been carried out since August; 1943; by A. W. Esty.Kidd has shown that, in the largely granitic country along the east side of Great Bear lake, the Echo Bay district is one of several underlain by older rocks . These he has divided into the Echo Bay and Cameron Bay groups. The former are strongly altered sediments, .porphyries, and lavas; the latter and younger group is predominantly sedimentary and far less altered. Associated with the granite, which everywhere intrudes the sediments and volcanics, are earlier differentiates. Later than all these rocks are various basic intrusives, collectively termed diabase. All the rocks are of Precambrian age."

Jan 1, 1954

By P. E. Weidmark

"PART I - Published PapersBallivy, G., and Dupuis, M., ""Laboratory testing for the design of grouted rock anchors""; Proc 6th Pan Am Conf Soil Mech Found Eng; Lima; 1:277-291; 1979.Ballivy, G., Ladanyi, B., and Gill, D., ""The effects of moisture content on the strength of fissured rocks""; Proc 1// 1ntnl Congr 1.A.E.G.; Madrid; //:2:7-16; 1978.Baumgartner, P., and Stimpson, B., ""Development of a tiltable base friction frame for kinematic studies of caving at various depths""; Int J Rock Mech Min Sci Geomech Abstr; 16:4:265-267; 1979.Bawden, W.F., and Roegiers, J.-c., ""Discussion and interpretation of the mathematics governing radial flow in a single horizontal rock fracture""; ISBN 07727-7002-6; Dept Civil Engng publication 79-11; Univ Toronto: 134p;1979.Chatterji, P.K., Smith, L.B., and Insley, A.E., ""Construction of Saline Creek Tunnel in Athabasca oil sand""; Can Geotech J; 16:1:90-107: 1979.Coates, D.F., and Gyenge, M., ""A case history of pit slope design""; Proc 4th ISRM Congr; Montreux, Switzerland; Sept 1979; 1:Theme IV:591-596; 1979.Crawford, A.M., and Curran, J.H., ""A dynamic direct shear machine for determining the time-dependent behaviour of rock joints"": Dept Civil Engng publication 79-08; Univ Toronto; 1979.Crawford, A.M., and Curran, J.H., ""A displacement discontinuity approach to modelling the creep behavior of rock and its discontinuities""; Dept Civil Engng publication 79-09; Univ Toronto; 1979.Crawford, A.M., and Curran, J.H., ""A higher-order displacement discontinuity element""; Dept Civil Engng publication 79-10; Univ Toronto; 1979.Cruden, D.M., ""A computer-based system for rock mass description""; Proc 1// Intnl Congr I.A.E.G.; Madrid; //:2:155-159; 1978.Cruikshank, D.J., and Curran, J.H., ""A.B.LE. approach to modelling of fluid flow in fractured rock masses""; Proc 7th Cdn Congr Appl Mech; May 1979; Sherbrooke, Que; 887-888; 1979."

Jan 1, 1980

By Y. Kusuda

Since 1981, the Annaka refinery has recovered zinc from zinc leach residues by the Waelz Process. The important considerations of this process are the prevention of the growth of coating accretions in the Waelz kiln and the improvement of the zinc volatilization rate. In this paper, simulation predictions and the results of the industrial operation regarding the prevention of coating accretions in the Waelz kiln and the improvement of the zinc volatilization rate at the Annaka refinery are reported and compared.

Jan 1, 2006

By S. Huang, K. Xia

"During crushing, rock particle is subjected to complicated loading and the particle shape influences the fragmentation outcome. Thus, a highly controlled laboratory test is desired to establish the relation between the loading and the fragmentation parameters for better understanding the rock crushing mechanism. In this work, a split Hopkinson pressure bar system in combination with high speed cameras is utilized to carry out a dynamic ball compression test, in which the spherical rock sample is adopted to avoid the shape effect. Using the elasticity theory, the history of the axial symmetric tensile stress perpendicular to the diametrical direction along the loading axis is determined, from which the loading rate and the dynamic indirect tensile strength are calculated. With the aid of the moment-trap technique, the total energy absorbed by samples is accurately determined from the one-dimensional wave analysis. Furthermore by considering the kinetic energy of the sample fragments using the high speed camera snapshots, the surface energy is determined for each sample. The relations between the loading rate and the fragmentation parameters, i.e., the number of fragments and the surface energy are established. The application of this method to a granitic rock shows that it is flexible and can be applied to the crushing study of generic brittle solids. INTRODUCTIONCrushers are widely used to break rocks to extract specific minerals in the mining industry, and to obtain rock fragments with desired size distribution in construction industry. During crushing, the breakage of particles can be in either the single-layer mode or the multi-layer mode. In the single-layer mode, the particle breakage can be assumed to be isolated, in which the interaction between particles can be ignored. It is thus suggested by many researchers that highly controlled single particle test should be performed to establish the relation between the input mechanical energy and size reduction for better understanding the crushing mechanism (Yashima et al., 1987; Tavares, 2007; Pitchumani et al., 2004)."

Jan 1, 2015

By Darryel Boucher, Thomas W. Leadbeater, Raymond Langlois, Joshua Sovechles, McGill University, Zhoutong Deng

"Spiral concentrators are used to upgrade ore based on the density difference between their component minerals. This simple flowing film gravity separator is of interest for the processing of large amounts of material, as found in the iron ore industry. Addition of wash water at different points on the trough of the spiral affects the grade and recovery of the valuable concentrate by affecting the flow of particles within the thin slurry film. This paper shows how radiolabelled hematite (-355+300 µm) and quartz (–1,180+1,000 µm) tracers were used to determine the particles’ behaviour within the slurry film with and without the addition of wash water. The results presented provide a detailed particle flow pattern around a wash water addition point and its effect on the trajectory and velocity of the particles. This information is of interest in building knowledge about spiral wash water injection parameters such as injection location, direction, flow rate and nozzle orifice type (affecting jet shape and velocity).INTRODUCTIONSpiral concentrators are density based separation devices. They are extensively used in the upgrading of iron ore, fine coal and minerals sands (sources of ilmenite, rutile, zircon and monazite) (Wills & Finch, 2016). A spiral unit is composed of a channel of specific profile formed as a helix of 3 to 7 turns around a central structural post. The feed pulp is composed of 15 to 45% solids with particle size from 75 µm to 3000 µm (Wills & Finch, 2016). Throughput of a single spiraling trough can be up to 8 ton per hour and multiple trough unit (up to four trough) can process up to 30 ton per hour for a footprint of around 0.7 m2 (Palmers & Vadeikis, 2010). They are low cost concentrators considering manufacturing of their trough via polymer reverse molding. The energy intensity of a spiral plan is notably small considering the throughput and is mostly related to pulp pumping and final concentrate dewatering."

Jan 1, 2016

By R. Kamguem

The surface of a mechanical part plays an important role in determining performance in service. The presence of scratches left by the cutting or tearing of the material on the surface of the workpiece supports the concentration of stress and strain. This article presents the experimental study for high speed milling of the aluminum alloy 7075-T6, using cutting tools different by the nose radius and coatings (TiCN, TiAIN, TiCN + A12O3 + TiN). A multi levels factorial design of experiment (DOE) and statistical analysis was used. The roughness parameters investigated are Ra, Ra, Rv, Rc, Rsm, and Rk. The results show that the feed rate, the types of coatings and the geometry of the cutting tools have the most significant impact on the surface roughness profil. Surface finish charts according to feeds and cutting speeds were established for each tool tested.

Jan 1, 2011