Search Documents

By A. Galibois, H. Monette, J. L. Collins

This paper deals with the problem of caving, which occurs in varying degrees in blast holes before loading. It is shown that the distribution of the amount of caving in materials may be described by a gamma density function. A decision model to determine the optimal depth of over-drilling 'in order to minimize the expected additional cost per hole is described. Two different policies are discussed. In addition, charts which permit the mine operator to realize significant savings have been drawn for different actual situations.

Jan 1, 1971

By H Zorychta

Based on underground measurements made at the Nova Scotia coal mines of the Dominion Coal Company, Limited, this paper presents a comparison between the physical properties of hardwood packs and steel friction props when used for longwall support. The probable loads sup-ported by steel friction props on a longwall face at both the Dominion No. 20 Colliery and the Princess Colliery are delineated, and the results of the tests are presented in graphical form. It is concluded that the steel friction props are more efficient than the hardwood packs that they replaced as roof supports. Introduction AN evolution in the methods of longwall face support is taking place in the Sydney coalfield. Longwall face support had consisted primarily of timber props and hardwood packs. In 1957, however, at the Princess Colliery, Sydney Mines, Nova Scotia, the first longwall was equipped with steel friction props. At the present time, eleven longwall faces are supported on wood and sixteen faces are carried on steel friction props.

Jan 1, 1965

By B. Dyck, C. Rodgers

ABSTRACT Cameco Corporation is revitalizing its Key Lake Operation uranium mill in northern Saskatchewan. The mill currently uses ammonia stripping in solvent extraction (SX) and ammonia yellowcake precipitation. As part of the revitalization, the company considered installing strong acid stripping in solvent extraction (used at its Rabbit Lake Operation), which would lead to using hydrogen peroxide for uranium precipitation. As part of the process evaluation, tests were carried out to study how the drying temperature in indirect fired dryers would affect the uranium peroxide yellowcake precipitate properties. This paper discusses the test work results, including the relationships between drying temperature and product reactivity with water, product colour, product grade, and energy input requirements.

Jan 1, 2012

By A. Haldar

This study focuses on the flow characteristics of hypereutectic Al-Si alloys in thin sections. The pattern assembly consisted of spiral horizontal patterns, 6.25 mm (0.25 inch) and 12.50 mm (0.50 inch) in thickness with a common sprue. Al-Si alloys with silicon levels of 14%, 18% and 22% were poured with superheats of 60°C, 115°C and 170°C. It was observed that metal fluidity (in terms of flow length and metal velocity) increased with increase in silicon levels and superheat for both section thicknesses. It was also observed that, for a section thickness of 6.25 mm (0.25 inch), silicon level had more pronounced effect on the metal fluidity. For 12.50 mm (0.50 inch) thickness, both silicon level and superheat affected the metal fluidity. The surface hardness of the castings increased with an increase in silicon level of the alloys at the gate and the flow tip. Detailed study of the flow tip was also carried out with a view to understanding the effect of silicon level and superheat on undulated flow length, surface hardness and microstructure.

Jan 1, 2007

By Hrayr Agnerian

The fair market value of an exploration property is determined by its potential to host a mineral deposit. This potential is gauged by the results of previous exploration, exploration stage, meaningful past expenditures and remaining targets that are not yet tested. Values of exploration properties can be viewed as distinct points in a three-dimensional space defined by orthogonal axes, namely: Exploration Stage (x-axis); Cumulative Expenditures (y-axis); and Property Value (z-axis). In general, these values are estimated by applying activity factors on previous exploration expenditures, e.g. an activity factor of 100% for an active property with good potential and a factor of 50% for an active property but past expenditures have not upgraded the property. At certain periods, a market factor may also be applied to reflect the activity of mineral property acquisitions. For properties that do not exhibit any exploration potential, only nominal values are applied.

Jan 1, 1996

By A. M. Elmahdy, T. Hirajima, M. Farahat

"Separation of molybdenite from chalcopyrite is mainly achieved through flotation technique to raise their grades up to 25% to be extracted in smelters. However, molybdenite recovery and grade obtained from this process is not satisfactory in most cases due to the natural hydrophobicity of both minerals. The influence of conventional heat treatment on pure chalcopyrite and molybdenite minerals was investigated. X-ray diffraction, TG-DTA and XPS techniques were applied before and after heat treatment. The results showed phase changes for both minerals. Magnetic separation experiments of single and mixture of both minerals at several magnetic intensities were made. For single mineral experiments, 100% molybdenite recovery was obtained at all experimental conditions as non-magnetic fraction whereas ca. 100% chalcopyrite recovery was achieved under certain conditions. In case of 1:1 binary mixture, 87% and 83% molybdenum and copper recoveries, respectively, were obtained. The increase in chalcopyrite magnetic recovery is related to the formation of more magnetic phases as confirmed by characterization techniques.The objective of this study is to increase the magnetism of chalcopyrite to make its separation from molybdenite by magnetic separation possible and to understand the mechanism behind it. These results indicate that it may be possible to upgrade molybdenite ores using heat treatment followed by magnetic separation to the required grade by smelters which is difficult to attain by froth flotation and the other techniques."

Jan 1, 2016

By R. Holmestad, M. Gazizov, S. Wenner, R. Kaibyshev, J. K. Sunde

"Mechanical properties and microstructure of an Al-4.7Cu-0.74Mg-0.51Si-0.48Mn-0.10Cr-0.09Ti-0.02Fe (wt. %) alloy subjected to various thermomechanical processing (TMP) have been investigated and compared to conventional ageing at 170°C (designated T6). Three TMP routes involving cold deformation of solution treated samples were tested. These were (i) 3%-stretching (T8-3%), (ii) equal-channel angular pressing (ECAP) to true strain (e) of ~1 (T8-1) and (iii) ECAP to e~2 (T8-2), all with subsequent ageing at 170°C for 0-96 h. At peak age conditions, both yield stress, ultimate tensile strength and elongation-to-fracture decreased for the T8-3% state as compared to the T6 condition. Intermediate ECAP (T8-1 and T8-2) lead to significant increase in maximum yield stress, ultimate tensile strength and elongation-to-fracture. The changes in mechanical properties were related to microstructure evolution, encompassing changes in grain sizes, dislocation densities, precipitate morphology and phase fractions, which were characterised using transmission electron microscopy. Relations between TMP, precipitation behavior and contributions to different strengthening mechanisms are evaluated.INTRODUCTION Al-Cu-Mg-Si alloys are widely used as structural materials in aerospace industry due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance. These properties are largely due to the formation of a large number of nano-sized metastable precipitates during artificial ageing (Polmear, 2006; Eskin, 2003; Gazizov, Dubina, Zhemchuzhnikova, & Kaibyshev, 2015). The precipitation behaviour in these alloys is complicated and depends among other things on Cu concentration and the Mg:Si ratio (Wolverton, 2001; Chakrabarti, & Laughlin, 2004). In general, the precipitation sequence has been presented in a prior study (Eskin, 2003) as follows:"

Jan 1, 2018

By Douglas R. Schmitt

In general, knowledge of the state of stress within the Antarctic lithosphere remains largely unconstrained due in part to Antarctica?s inaccessibility and because of the paucity of seismic focal mechanism solutions. As such, an important component of the ANDRILL project was to acquire new information on the stress directions and magnitudes within the upper crust. Extensive fracture mapping of the core and oriented ultrasonic televiewer logging were carried out to provide strong constraints on both stress orientations and the faulting regime. The first hydraulic fracturing stress determinations in Antarctica were also carried out to provide complimentary stress magnitudes. These measurements were accomplished using a wire-line transported hydraulic fracturing system consisting, essentially, of two synthetic polymer packers that were inflated to isolate the 1-m long pressurization interval. The tests were conducted at the end of the drilling and logging in a ~130-m section specially drilled below 1000 mbsf (nearly 1500 m from the rig floor) for hydraulic fractures. This zone was drilled primarily through competent, dense, and low permeability diamicts. The core fracture and televiewer logging information was used to site twenty separate measurements. Classic hydraulic fracturing pressurization records with unambiguous breakdown and fracture closure pressures were obtained in about half of the measurements. The remaining tests provided fracture propagation and closure pressures that are consistent with the classic breakdown curves, but they did not include a clear breakdown pressure and are indicative of the reopening of either natural or drilling induced fractures in the wellbore wall. The preliminary analysis of the results are in generally good agreement with the stress directions indicated by the core fracture logging and the stress regime suggested by the character of the drilling induced core fractures.

Jun 1, 2012

By W. Dietzel

Fracture mechanics based techniques are used to gain insight into the phenomenon of stress corrosion cracking (SCC) and to develop guidance for avoiding or controlling SCC. From constant extension rate experiments under rising load or rising displacement conditions the susceptibility of high strength steels, aluminum, magnesium and titanium alloys to SCC and hydrogen embrittlement can be assessed. Such tests on pre-cracked specimens are also well suited for studying the mechanisms leading to SCC by employing appropriate models for the degradation of metallic materials which take into account the uptake of atomic hydrogen from the corrosive environment. Measurements of crack growth resistance curves using the crack tip opening displacement as fracture parameter can be compared with simulated R-curves obtained from modeling of the mechanism of hydrogen embrittlement. The materials investigated are a high strength steel and a magnesium alloy both exposed to environmental conditions which fostered the uptake of hydrogen.

Jan 1, 2010

By K. Bowes, M. D. Maley, R. J. Ring

The Honeymoon Uranium Project is an acid In-Situ Recovery (ISR) mine in South Australia. It was previously operated for approximately 18 months before being placed on care and maintenance in 2014, it was then acquired by Boss Resources in 2015. Boss has been performing a number of studies to plan for reopening of the mine, including a successful field leach trial (FLT) in 2017. The current configuration for uranium precipitation at Honeymoon is a batch process. Whilst this achieves effective uranium recovery, the precipitates produced are often very fine, with poor settling and solid/liquid separation characteristics. Continuous precipitation, involving recycling of solids, has reportedly been successfully utilised in other operations to increase the particle size and density of the product, leading to solids that can be more readily dewatered, dried and drummed, with less fines and dust generation. However, no operational data are available from such operations.

Jan 1, 2020

By J. P. Harrison, K. Gao

It is well known that in situ stress measurements at a given site will generally display significant variability. However, it appears that a robust analysis of such measurements – i.e., one that is faithful to the tensorial nature of the data – is not available. Despite the fact that stress is a tensor, stress magnitude and orientation have long been analyzed separately using classical statistics. In earlier work we demonstrated the applicability of tensor statistics to the analysis of stress variability. Here, we investigate further the difference between tensor and classical statistics with respect to the stress tensor correlation matrix. Our analysis commences with the selection of a series of valid correlation matrices. Then, assuming that standardized tensor components follow the multivariate standard normal distribution, these correlation matrices are used to generate marginal probability distributions of the eigen-parameters (i.e., principal stress magnitude and rotation angle). From these, random stress tensors are generated, their eigenparameters determined, and the probability density distributions of these obtained using both classical and tensor statistics. Our results indicate that, for all correlation matrices, both methods give practically identical distributions for principal stress magnitude. However, the discrepancy between the two methods with regard to probability density distribution of rotation angle is highly dependent on stress component correlation. This discrepancy is usefully quantified in terms of the integral, with respect to orientation, of the difference between the two probability density distributions. This parameter, which we term Area Difference, is closely linked to the magnitude of the correlation matrix determinant, which itself is related to the normal stress correlation coefficient (i.e., ?x ,?y ??). Assuming that Area Difference should not exceed 0.1, we identify the critical determinant for any particular value of normal stress component correlation coefficient. Thus, using published in situ stress data and the obtained critical determinants, we show that for a specific normal stress component coefficient, when the correlation matrix determinant is less than its critical determinant, the more precise tensor statistics should be used to calculate the distribution of rotation angle. These results demonstrate that the customary analysis of stress measurement data may lead to erroneous results, and that tensor statistics appears to be preferred approach.

Jan 1, 2015

By Kathy S. Kalenchuk

Damages have been observed in shafts, backfill infrastructure and the slick line at the Leeville Mine. Shaft damage (shearing and spalling of the concrete liner) is attributed to mine-induced rock mass deformations concentrated where regional faults intersect the shafts. Aggregate bin, mixer station and conveyor drive damage (shotcrete shearing, heave of concrete floor slabs and bending of a vertical steel beams) is attributed to rock mass squeezing induced by elevated magnitudes of the vertically orientated major principal stresses. Separation of the slick line has occurred do to extension of the stressshadowed rock mass immediately above the mined out areas. Three-dimensional numerical models have been developed and calibrated to simulated rock mass deformations with magnitudes similar to those believed to have produced the observed damages. By stepping through the mine sequence, models reproduce deformations at the same mining stage as when damage has occurred. Calibrated models have been used to forward project further damage over the remaining mine life.

Jun 1, 2012

By S. Isaac

The networks of interdependencies between elements in building projects, referred to as the project topology, are often complex and difficult for project teams to comprehend. It is hypothesized that a graphbased model of the project topology can be based on existing data in Building Information Models (BIM), facilitating the application of graph-theoretic algorithms to analyze this topology. The objective of this study is to propose an outline for the synthesis of BIM and graph theory. This synthesis is expected to contribute to the development of new tools for representing, managing and analyzing the design of building projects.

Aug 1, 2013

By H. M. Kim, J. Rutqvist, D. W. Ryu

"Demand of high pressurized gas storage in underground rock caverns is increasing. Compressed natural gas (CNG) and compressed air energy storage (CAES) are one of the promising examples after since lined rock cavern (LRC) concept has been verified through in-situ pilot tests. Two key essential concerns of high pressured gas storage in underground rock caverns are mechanical stability of the cavern against high inner storage pressure and the risk of gas leakage from the caverns.In this study, we introduce our results of numerical simulations so as to investigate the potential of monitoring for gas leakage at a pilot facility for CAES in underground LRCs. The pilot facility was constructed at a comparatively shallow depth of 100 m, compared to the previous cases with several hundreds of meters, aiming at validating the feasibility of the LRC storage concept in which inner sealing liners, consisting of steel plate and concrete linings, are installed inside the excavated rock caverns (KIGAM, 2011). Compressed air may leak through either initial defects of inner containment liners such as imperfect welding regions and in-situ construction joints of the liners, or through structurally damaged points of the liners during the CAES operation where compression and decompression of the caverns are necessarily repeated and their structural robustness can be deteriorated.For this perspective, we carried out a coupled thermodynamic and geomechanical deformation analysis using TOUGH-FLAC simulator, and investigated the effectiveness of strain monitoring method in detecting mechanical failure of liners which may provide major pathways of air leakage. We therefore used an equivalent continuum model to relate the localized tangential strain to fracture permeability changes, which was developed in our early work (Rutqvist et al, 2012). In detecting and characterizing the leakage location, we tested a cross correlation technique using the synthetic pressure responses monitored in case of the failure of the inner liners. From the investigations, we showed that tangential strain, rather than radial, monitoring especially at the inner face of the sealing liners can be more effective in detecting the mechanical failure of the liners.In localizing the leakage point, we noted that the interface between the inner liners and surrounding rock may not be perfectly bonded so as to increase permeability through which any leaking air pressure may migrate more dominantly. We also demonstrated that the cross correlation of the time histories of pressure measurement especially at these interfaces can be useful in identifying the leakage point. These results may provide useful information in overall design of monitoring and alarming system of our upcoming CAES pilot facilities."

Jan 1, 2015

By James Ball

The paper describes a new type of pump and related apparatus specifically designed to dredge sea-floor minerals from very great depths. The principle of operation of the dredging system is explained, and the factors which determine the equipment size and the power required for varying mining rates and depths of water are discussed. An estimate of the capital and operating cost of a commercial-scale mining system is presented.

Jan 1, 1968

By V. V. Zubkov

The systems of geophysical monitoring have been already put into operation at coal mines and ore mines. Since at present it is rather difficult to conduct mine experiments; it is necessary to start a new step in joining of geomechanics and seismic. The linking geomechanical and geophysical monitoring at coal mines and ore mines today became possible due to progress in development of numerical methods of modeling of stress state and technology for processing of seismic information. This paper describes one potential step in linking geomechanical and seismic monitoring at coal mines and ore mines.

Aug 1, 2013

By Mousa Mohammadi

Due to operational advantage of dragline in simultaneous excavation and back-filling, the equipment has gained vast importance in open-pit mining. Besides, absence of auxiliary haulage units and a myriad of other benefits are also credited in favor of excavation of muck piles by the draglines. However, the aspects of production, productivity and economics are of utmost significance in dragline operation and planning. In this light, the present paper is an endeavor to analyze availability and utilization of dragline operations. The paper presents a good amount of data for 4-draglines operating in one of the major opencast projects in India. The study reveals the trends of availability and utilization of these draglines during last 11-years. Furthermore, the study also highlights the salient reasons for loss of available hours and for idling of the draglines. Some startling information and facts have been illustrated in form of graphs and pie charts.

Aug 1, 2013

By J. Fellowes, V. Landais, J. Robson, J. Carr

"Aerospace Al-Zn-Mg-Cu (7xxx) alloys are known to be susceptible to environmentally assisted cracking (EAC). This phenomenon has been studied intensively for many decades, leading to empirically adopted methods to mitigate this problem through overaging and composition design. In parallel, many theories have been developed to explain EAC in 7xxx, but none is yet universally accepted. Today, a number of emerging techniques offer potential to shed new light on EAC in 7xxx. The purpose of the present paper is to demonstrate how X-ray tomography (XCT) combined with electron microscopy can be used to identify the true crack path in 3-dimensions, and hence identify material for site specific electron microscopy analysis. Composition mapping over large areas to high accuracy has been performed using a modern electron microprobe analysis system. This has been combined with transmission electron microscopy to investigate local composition in matrix and precipitates at high resolution. This combination of techniques across length scales offers the potential to provide new insights into the links between local composition, microstructure, and EAC resistance.INTRODUCTION Environmentally-assisted cracking (EAC) is a phenomenon which dramatically decreases the performance of metals and can cause premature failure of large structures. Observed in situations where components were not subjected to critical loads and no widespread corrosion was involved, this type of brittle failure is extremely difficult to predict. The EAC designation covers a number of phenomena, e.g. stress corrosion cracking (SCC), hydrogen embrittlement (HE), corrosion fatigue (CF), etc. Initially identified in steels, EAC can also affect other metals such as high-performance aerospace aluminium alloys, and this phenomenon has been a concern for industries for decades. Extensive research has been conducted on the effects of various environments (moist air, saline water, dry hydrogen gas, etc.) on microstructures and crack propagation, however no consensus has been reached and the exact nature of the mechanisms that control EAC is still being debated (Birnbaum & Sofronis, 1994; Gangloff, 2007; Holroyd & Scamans, 2013; Lynch, 2012; Oriani, 1972; Scamans, Alani & Swann, 1976, Young & Scully, 2002)."

Jan 1, 2018

By W. B. Boggs

A paper describing the Noranda smelter was presented at the 1930 annual meeting of the Institute (1). A lacer article appeared in the Trans-actions of the A.I.M.&M.E. in 1933. Since that time there have been many changes and improvements in plant operation and it is the abject of this paper to give an account of developments up to the beginning of 1939. The Noranda smelter was built originally for a capacity of 30,000 tons a month. At present, the average tonnage being treated is 110,000 tons a month, the tonnage of custom ores alone amounting to almost the total rated capacity of the original plant. This increase has been accomplished by increasing the capacity of the reverberatory furnaces from 700 tons of solid charge per furnace day in 1928 to 1,500 tons per day at the present time. In 1935, it appeared chat the limit of furnace capacity had been reached at about 1,300 tons of charge per day because of the short life of the sprung silica arches. However, the adoption of the suspended magnesite roof, which had been developed at the Flin Flou smelter of the Hudson Bay Mining and Smelting Company, overcame this difficulty and it is believed that the limit of the capacity of the present reverberarory furnaces has not been reached. A brief account of the changes to equipment in the various departments will be given, followed by a description of the more important features of present smelter practice.

Jan 1, 1939

By S. Uddin

Microsegregation manifests its effect on microstructural evolution of cast or welded alloys which in turn influences their important mechanical and electro-chemical properties. In the above context, mathematical models of microsegregation have proven to play an important role in estimating the nature and predicting the effects of this phenomenon in wide varieties of solidification processes. Microsegregation models are useful in designing new commercial alloys, in estimating the homogenization time for the post-process heat treatments and in many other practical applications. In this study, two semi-analytical models of microsegregation were developed to predict the concentration field of solute in the liquid and solid regions for dendritic solidification of binary metallic alloys. Both models assume that the growing dendrites are cylindrical in shape. This assumption is more realistic compared to the common assumptions of plate like dendrites that most of the earlier researchers employed in their microsegregation modeling study. The solute redistribution profile, in the developing solid layer, necessary to determine the back diffusion parameter was derived from Fick's second law for the model without coarsening. The application of this parameter in a wide range of conditions and the use of its basic form in the model with coarsening has been verified. The concept of coordinate transformation and enhancement of back-diffusion Fourier number were used in deriving the model which took into account the coarsening of dendrites. The models are then extended to deal with rapid solidification and peritectic transformations and the results were compared with relevant experimental data for Aluminum and other alloys. A good agreement between model predictions and experimental results was found.

Jan 1, 2007