Search Documents

By W. L. Nelson

The orebodies at Copper Mounta1n lie along and within a few hundred feet of the contact of an intrusive stock of gabbro with a series of bedded volcanic rocks of the Nicola formation. These. orebodies are all entirely within the volcanic series but in many cases the centre line of the orebody at depth is directly under the gabbro contact at the surface, due to a slight overhang of the gabbro. The gabbro and volcanic rocks are cut by a number of faults and fault zones which did not materially affect early mining operations, but, as undeground openings increased in size, the faults became more important factors in determining mining methods and procedure. Caving methods were adopted to take advantage of ground weakness in fault zones, and the effect of ground subsidence which resulted from the division of the ground 1nto large, independent blocks by faulting had to be considered in planning the sequence of mining of certain ore blocks. The faults have been divided into two classes: the longitudinal system and the cross faults, or 'breaks' as they are termed locally. In addition to the two classes of faults, the zones of parallel ore fracture also control mining procedure, but to a lesser degree, in regard to caving or ground subsidence. A third structural feature which influences mining procedure is the mine dyke system. The longitudinal or main fault system roughly parallels the gab? bro contact and is made up of a number of branches and auxiliary fractures. The main fault itself is essentially vertical, but there are a number of branches and fractures on each side of it which, though parallel m strike, may dip as flat as 50 degrees toward or away from the main fault. The full width of the main fault system has not been determined, but it is known to extend beyond the zone of mine workings. A marked schistosity follows the main fault and both schistosity and chloritic alteration have been noticed along the secondary faults of this system. Several prominent orebodies lie along the main fault and its branches. The influence of the main fault system on mining is probably related more to subsidence than to actual cavi.ng, although it is effective in both.

Jan 1, 1950

By K. G. Chipman

IN 1936, the Department of Mines and Resources was formed by the amalgamation of the former Departments of Mines, Interior, Indian Affairs, and Immigration. In the amalgamation, the Geological Survey and the Topographical Survey became the major divisions of the Bureau of Geology and Topography, which is a part of the Mines and Geology Branch which, in turn, is a part of the Department of Mines and Resources. The Topographical Survey was formed by combining the former Topographical Division of the Geological Survey and the air and ground mapping sections of the former Topographical and Air Survey Bureau of the Department of the Interior. The latter organization, previous to 1933, had been known as the Topographical Surveys Branch of the Department of the Interior. The amalgamation of 1936 definitely placed on the Topographical Survey the responsibility for the original mapping required for the development of our natural resources. The war has brought upon us the situation where all work has had to be in the furtherance of the war effort. With decreased staff and limited appropriations, the mapping on those scales which are directly concerned with the natural resources has been confined to the search for oil and strategic minerals. The reconstruction period will produce a different situation, with different problems. The past is behind us and it is necessary to prepare for the future. First, we should consider briefly a few general principles in the making and using of maps, then take stock of what we have, see what the needs are, and consider how we are to meet these needs.

Jan 1, 1944

By J. A. Russell

IT IS the purpose of this paper to show how the design of the larger slope hoists in use in the mines of the Dominion Steel and Coal Corporation has tended to evolve ta suit the particular conditions of operation. These hoists are all used for hauling coal in trains or trips of pit tubs up the mine slopes, which usually follow the dip of the seam . As the mine is developed to the dip and the slope grows in length, the length of the rope and the size of the hoist required to handle it rends to become extremely cumbersome. It has been found that the best economic conditions of hoisting are obtained when the length of the slope is limited to about seven or eight thousand feet. Beyond this length it is necessary to offset to one side of the line of slope and start a second or auxiliary slope, which will be served by its own hoist installed underground. With this hoisting distance as a basis, we find that we can economically hoist the outputs required, usually about 1,500 tans per eight hours per slope, by hoisting the coal in trips of about twenty boxes. This, on the grades obtaining, will require a rope of about l 1/4in. diameter, running at a speed of 1,200 ta 1,800 feet per minute, and requiring from 1,200 to 1,800 h.p. at the hoist shaft. The tendency is for the rope speeds of the surface hoists to be a little higher than the underground hoists which relay to them, so that the surface hoist has a small margin of time in hand. The oldest surface hoists were steam-driven, but, with few exceptions, these have given place to electric hoists. With the exception of one hoist, which was altered in design, the steam hoists have not had the opportunity of evolving in the same way as the electric hoists, and will not be mentioned any further.

Jan 1, 1944

By B. K. Ayres

Modern management of uranium mine or mill waste storage facilities (WSFs) often requires that they be remediated or decommissioned with a cover system. In addition to creating a self-sustaining landscape that supports the end land use, cover systems are intended to reduce long-term risks to human and ecological receptors from the stored waste to acceptable levels. The performance and longevity of a cover system will be strongly influenced by the features or shapes of the WSF final landform. Hence, cover systems and landforms must be thought of as an integrated design. Based on the author’s experience, the most important elements of the design process for maximizing the potential of WSF final landforms / cover systems being sustainable over the long term are noted in this manuscript. Several key items that must be considered and addressed during the planning phase of constructing a WSF final landform are also described. Various methods for monitoring performance of a WSF final landform are also reviewed. Key aspects associated with decommissioning a tailings WSF and waste rock pile at the former Cluff Lake uranium mine in northern Saskatchewan are included to illustrate many of the practical insights provided in this paper.

Jan 1, 2020

By M. O. Pekguleryuz, D. S. Aydin

The high temperature oxidation and ignition resistance of Mg-(0-6) wt% Nd alloys have been investigated via isothermal and continuous heating experiments conducted in air atmosphere. Alloy composition is observed to be effective in low levels (~ 0.5 %) in the ignition temperature (Ti) of the alloys; the Ti of pure Mg increased from 630 °C to 770 °C with 0.5 wt% Nd addition. However, no noteworthy improvement was achieved with further additions up to 6 wt% Nd. The initial microstructure was observed to determine the oxide structure on the surface due to the differing oxidation behavior of the phases (a-Mg + Mg12Nd intermetallics). It has been found that the formation of a Nd-depleted region at the subsurface due to extensive Nd oxidation at the oxide/intermetallic interface lowers the protective ability of the oxide scale.

Jan 1, 2015

By S. H. Ash

Introduction Probably the newest thing in mining safety is the apparent dissatisfaction on the part of the mineral industry, as represented by both management and labour, and the general public of many nations in which mining is conducted, with the safety record of the mining industry. This is reflected by published comments in the technical press;' in labour periodicals, in popular Journals and periodicals, and in the daily press (5, 11). Despite what may be said to the contrary, mining in the United States is becoming safer, and this trend has been evident for several years (see Figures 1 to 4). Because the author's experience has been mostly in the United States this paper will discuss briefly some recent observations in the United States that have a bearing on mining safety. Because coal mining is of primary interest to the Mining Society of Nova Scotia, the paper treats mostly of coal-mining safety; however, many hazards in mining .are common to all mines, regardless of the minerals mined.

Jan 1, 1950

By John Kruse, Sethu Raman, Dave Tenney

The Cullaton Lake B-Zone gold mine was the first gold producer in the Kaminak Subprovince of the Canadian Shield . Located approximately 650 km north of Thompson. Manitoba, the mine produced 77,783 ounces of gold and 5,564 ounces of sil ver from 251 ,236 tons of ore during 1981-84 period. The depos it is a small , structurally controlled , stratabound orebody in an Archean iron formation. Most gold occurs in sulphide and silicate fac ies. Based on new ev idence, the depos it is interpreted to have fo rmed by remobilization of syngenetic low-grade gold mineralization in the iron fo rmation in a favoura ble fold structure. The concept and methods developed at the mine have been successfull y applied in the discovery of new deposits in the area. One of the concepts. which link Archean and Proterozoic mineralization. may have wider applications in the search fo r gold deposi ts elsewhere in Canada .

Jan 1, 1986

By A. Blackmore, D. Baker, L. Human

"Mechanical mixing equipment is common in a wide variety of mining, metals and process applications, such as hydrometallurgical reactors, solvent extraction, digestors, and tanks for storage of slurry or hydrocarbons. Computational Fluid Dynamics (CFD) has been applied successfully to single-phase mechanical mixing problems for several decades and is established as a reliable design tool. As computational power and CFD codes have improved over the years, there have been significant advances in modelling capabilities including improved models of turbulence, interaction of rotating and stationary components, multiphase flows, and modelling of free surface interfaces, for example. This paper will provide an overview of the application of CFD to mechanical mixing problems. First, it will review the traditional single phase Multiple Reference Frame (MRF) approach and introduce a range of advanced modelling techniques. Three examples of the application of CFD to industrial mixing problems will be given. It will be demonstrated that CFD is an effective tool for reducing technical risk in design, for identifying the root-cause of mixing problems, and testing modifications to existing operations."

Jan 1, 2015

By K. Lillkung, J. Kourunen, M. Latva-Kokko

"Carbon-in-leach (CIL) and carbon-in-pulp (CIP) processes utilize activated carbon to adsorb solubilized gold for recovery. Due to carbon attrition and non-ideal carbon management, however, some of the gold is lost in carbon fines and to the solution. The carbon attrition mechanism inside CIL/CIP reactors is mainly abrasion-related. This is critical to gold loss since gold loading takes place predominantly in the outer shell of the carbon particles. Thus fine carbon dust has a relatively high gold content and such a small particle size that it cannot be captured with safety screens. The attrition rate depends on ore and carbon characteristics, but it is always proportional to the mixing power intensity. This rate can be minimized by continuous suspension level measurement and control of agitation speed. In addition, a novel tank bottom structure can significantly reduce the required mixing power input compared to a flat bottom tank. A major challenge in carbon management is infrequent and inaccurate measurement of carbon concentration in the reactors. In order to reduce soluble gold losses by means of improved carbon management, Outotec has been developing a continuous in-situ measurement for carbon concentration that is tolerant to changes in slurry density.INTRODUCTION Cyanide leaching has been utilized since the late 19th century as a standard technology for hydrometallurgical gold production. Since then, gold and silver recovery rates have increased due to technological development, but very similar recovery methods are still being used. The original recovery method was to use zinc precipitation – similar to the Merrill-Crowe process, which is still common for feed materials with low throughput and high silver content. However, in most cases, activated carbon recovery is preferred due to its improved efficiency. The carbon-in-pulp process (CIP) and its modification, carbon-in-leach (CIL), have a lower residual soluble gold level and are not similarly affected by soluble base metals. The main alternative for the use of carbon is ion exchange resins. The principle of resin processes is similar to the CIL/CIP processes, with a different type of adsorbent material. Carbon processes are usually preferred over resin processes due to the significantly higher cost of resin material and the possibility to use simpler, well-established technology with carbon processes."

Jan 1, 2017

By Sib N. Mukherjee

Main ventilation fans are used in all the mines and they run continuously 24 hours a day and 365 days in a year. Any improvement in their performance can lead to considerable power saving. The basic principle for selection, operations, and related measures are discussed in brief in the paper. The contributions of different elements of mine fan on its performance are discussed in brief. The means to improve efficiency of a running fan is also discussed and the importance of saving even 1 Kwh is elaborated. It is found that the cost of the energy saved may even permit a replacement fan to be procured in a few years time.

May 1, 2007

By C. Pichler, C. Benigni, J. Antrekowitsch

"The recycling of steel mill dust results in zinc oxides which are sold to the primary industry in or-der to recover zinc in its metallic form. Due to the contained impurities - chlorine and fluorine - these sec-ondary oxides are usually charged into the roaster together with primary concentrates. Appearing problems in this furnace limit the application of secondary materials. Based on the zinc amount, a direct leaching, assumed that a low halide concentration is present, would be possible. To use the zinc solution directly in the electrowinning stage, the concentration of impurities, first of all iron, is limited. Iron can be found in secondary zinc oxides due to carry over during the recycling process. In order to reduce the iron content in the solution, the leaching has to be pH-controlled. This leads to a limited number of simple purification steps before the solution enters the electrolysis. Various trials were performed to evaluate the influence of temperature, time and sulphuric acid concentration on the iron dissolution. This paper deals with the results and also focuses on other impurities such as halides. Additionally, the soda washing process, usually done with secondary zinc oxides to remove most of the halides, and the challenges within this step are discussed.INTRODUCTION Recycling of steel mill dust, which is the main zinc containing residue, in the Waelz process dis-plays the common method worldwide. The product of the process is a secondary zinc oxide which is con-taminated with different elements like lead, iron and halides due to mechanical carry over or evaporation. Depending on the feeding material the concentration of each element in the dust is varying. The zinc con-tent of the product, also called Waelz oxide, lies around 65–68%. Based on these values it presents an al-ternative to the primary concentrate for the production of metallic zinc. The contained halides limit the direct utilization in the leaching stage and therefore have to be reduced. State of the art is a soda washing process but also solvent extraction gives a possibility to remove chlorine and fluorine but the desired con-centration for the electrolysis is hardly reachable (Antrekowitsch et al., 2016) Iron is present as an undesirable component of such secondary zinc oxides due to carry over. During the hot acidic leaching of the secondary concentrate, iron is dissolved too. Based on the higher electrical potential iron has to be removed before the zinc solution enters the electrowinning stage. It is usually removed by precipitation as goethite, hematite or jarosite, which is the common precipitation residue (Ismael et al., 2003)."

Jan 1, 2017

By Bird. M.

As the Cadia mill was the first 40ft diameter SAG mill, commissioned in 1998, its performance, liner and discharge design attracted considerable international attention. Twelve years on, the liner design and the control philosophy are being readdressed to further improve the mill?s performance. A comprehensive series of 3D liner scans, over life of the liner, have been used to calibrate liner mass loss and progressive changes in the liner profile. This data is being used to provide true charge mass and mill filling, plus progressive trajectory profiles over life of liner. This information, along with measures of mill performance over liner life, is being used to select the optimal operating conditions as the liner wears, and hopes to inform future liner design.

Jan 1, 2012

By W C. Shakespeare

The Ontario Committee on Taxation is making a comprehensive study of taxation in the Province of Ontario, and in this connection has received representations concerning mining taxation from a number of interested parties. Some of the more important recommendations on mining taxation are reviewed in this article. Introduction FOLLOWING the appointment of the Federal Royal Commission on Taxation, the Ontario Government, effective in November, 1962, appointed the Ontario Committee on Taxation to review taxes and revenues available to the Province of Ontario and its local governments, to co-operate with the Royal Commission on Taxation and with any other bodies of enquiry appointed by other provincial governments, and to make such recommendations as it sees fit to the Prime Minister of Ontario and the Executive Council. The members of the Committee are: MR. L. J. SMITH, F.C.A., Toronto, (Chairman) MR. ERIC HARDY, Toronto DR. R. CRAIG MCIVOR, F.R.S.C., Hamilton MR. CARL A. POLLOCK, Kitchener MR. R. BREDIN STAPELLS, Q.C., and Toronto. Like its Federal counterpart, the Royal Commission on Taxation, the Ontario Committee has held public hearings, has received written

Jan 1, 1965

By K. Chattopadhyay

Fluid flows in metallurgical reactors play a vital role on liquid metal cleanliness for both ferrous and non-ferrous metallurgy. Thus, it is absolutely critical to understand different fluid flow mechanisms, and the use of computational methods to model the complex non-isothermal, turbulent, single- and multiphase-flows, has to be appreciated. The present case study emphasizes on controlling the flow of liquid steel in a tundish and enhancing liquid metal cleanliness. CFD modeling was used to build a robust mathematical model, and effects of flow control furniture and non-isothermal conditions were analyzed. The mathematical model was validated against water model experiments. Parameters that were conducive for inclusion removal were identified and implemented in the plant. Some flow control devices could increase inclusion removal to a great extent compared to the existing configurations. In cases, where a hot ladle was poured into a relatively cooler tundish, inclusion removal was better, whereas results were catastrophic in cases where colder liquid was poured from ladle to the tundish. Similar techniques can be applied for other liquid metals including light metals and non-ferrous metals.

Jan 1, 2015

By Seungyeol Lee

Currently, a new construction method using a robotic system is widely spreading in construction sites. This study is related to the design of glazing robot?s teach pendant which can improve convenience of handling and hence improve the productivity through the efficient interaction between an operator and a robot while doing glazing works, e.g., curtain wall installing. The suitability of selection and arrangement of control switches was assessed according to mechanical motions of a glazing robot, and design guidelines for improving convenience and productivity were drawn up through questionnaires carried out by site operators. To verify the proposed design guidelines, working time comparison of the proposed teach pendant and the existing teach pendant was executed.

Aug 1, 2013

By C. Piribauer, E. Feichtenhofer, A. McEneaney

"As part of a major diversification project, RHI AG, through its plant in Drogheda Ireland, has developed a Caustic Calcined Magnesium Oxide (CCM) for use in the Cobalt (Co) & Nickel (Ni) hydrometallurgical extraction industry. In the course of the project, the company investigated the chemical and physical properties of a number of different Magnesia’s used in Co & Ni hydrometallurgy applications and has been able to determine the important parameters for a successful Magnesia for this application. A number of live plant trials have confirmed the results of this testwork and the company is now proceeding to produce this product in commercial quantities at Premier Periclase Ltd., the RHI AG plant in Drogheda, Ireland. This paper will outline the development work conducted by the company and highlight the important chemical and physical properties that make a successful CCM. Much of the research was conducted at the RHI Technology Centre in Leoben, Austria. In addition, a number of external laboratory studies were conducted on behalf of RHI AG. The result of this work has allowed the company to develop a Magnesia product with optimised properties for use in the Cobalt and Nickel hydrometallurgical extraction process.INTRODUCTION Premier Periclase is part of RHI AG, a globally operating supplier of refractory products, systems and services, headquartered in Vienna, Austria. The company produces Magnesia from seawater at its plant in Drogheda, Ireland. While the main focus is on production of refractory grade Dead Burned Magnesia for the steel industry, the plant also produces a number of different grades of Caustic Calcined Magnesia as well as Magnesium Hydroxide products. As part of a major project to diversify the company’s product base, the use of CCM in the Cobalt (Co) & Nickel (Ni) hydrometallurgical extraction industry was investigated. One of the company’s highly reactive grades of Caustic Calcined Magnesia was found to be particularly suitable for this application. In an effort to understand what makes a successful Magnesia for hydrometallurgy the chemical and physical properties of different Magnesia’s used in Co & Ni hydrometallurgy were investigated. This paper and conference presentation outlines the findings of this process."

Jan 1, 2017

By R. D. Brown

The Federal Government's White Paper on Tax Reform received further major criticism in the reports of the Committees of the House of Commons and the Senate, which recently completed a lengthy review including public hearings of the government's proposals. These reports both criticized the emphasis placed by the White Paper on its concept of tax equity rather than on a system which would promote economic growth. However, the Finance Committee of the House of Commons was prepared to accept, with modifications, a number of the White Paper's key reform proposals. The Senate Finance Committee was more critical of the basic thrust of the tax reform program and recommended that a modification of the existing tax system would be more appropriate to Canada's needs. Both Committees re-commended a more favourable treatment of mining income than that originally proposed in the White Paper, and to some extent both Committees suggested proposals that were even more favourable to the industry than those set out in Finance Minister Benson's amended proposals made in August of this year. This article out-lines the principal recommendations and comments in the reports of both the House of Commons Committee and the Senate Finance Committee.

Jan 1, 1971

By Y. Héroux, A. Chagnon, M. M. Savard

"Résumé- Le gîte de Pb-Zn de Gays River s'accompagne d'anomalies des propriétés de la matière organique (MO) et des assemblages de minéraux d'argile (AMA). L'association entre la minéralisation, la distribution de la réflectance de la MO et des AMA suggère que ces traceurs peuvent servir à l'exploration des sulfures de métaux de base dans cette région.A l'emplacement du gîte, la réflectance varie considérablement (0,80% à 1,88%), pouvant même afficher une baisse avec l'enfouissement, ce qui est interprété comme une altération chimique de la MO. Les valeurs les plus élevées s'accompagnent localement de quelques textures en mosaïque et délimitent une anomalie thermique au centre sud de la région. Parmi les minéraux des argiles identifiés, l'illite et la chlorite sont terrigènes alors que la smectite, la kaolinite et la corrensite sont authigènes et, à l'instar de l'altération de la MO, résultent des nouveaux équilibres chimiques créés suite à la précipitation des sulfures.Abstract- The Gays River Pb-Zn ore deposit is associated with anomalies defined from the characters of the organic matter (OM) and from the clay minerals assemblages. The relationships be­ tween these anomalies and the mineralization at the mine suggest that these parameters can be used as new guides for the exploration for base-metal sulfides in this area.The vitrinite reflectance (RJ shows a wide range of values (0.8% to 1.88%) and exhibits an anomalous suppressive effect with depth of burial at the mine site, suggesting a chemical alteration of the OM. The highest R, values are associated with mosaic textures and outline a thermal anomaly at the south-center of the studied area. Among the identified clay minerals, illite and chlorite are terrigenous, whereas smectite, kaolinite and corrensite are authigenous and, like the alteration of the OM, are due to the new chemical equilibria resulting from the precipitation of the sulfides."

Jan 1, 1994

By A. Holland, T. Krumins, E. Olin, J. F. M. Castilleja, J. Geldart, C. Fleming, I. Jackman

A flowsheet has been developed to treat the flotation tailings from a copper mine in Mexico to recover gold and silver by cyanidation and carbon-in-pulp (CIP). The plant will treat ~15,000 t/day of a 60:40 blend of current flotation tailings and the mine’s historic tailings. The tailings also contain a significant amount of cyanide-soluble copper, and the economic viability of the project is strengthened by recovering most of the copper and cyanide associated with this process. The solution and solid phases in the CIP tailings will be separated in a counter current decantation (CCD) circuit and the CCD solution overflow will be treated by a SART Process. Copper precipitates as a salable copper sulphide product in the SART Process and the cyanide that is associated with the copper complex is regenerated as free cyanide. After SART, a portion of the SART product solution will be recycled to leach to reuse the free cyanide, while the remaining solution will be used as wash water in the CCD circuit. Incorporation of the SART Process in the flowsheet allows the CIP circuit to be operated aggressively as a gold plant, which means most of the silver in solution passes through CIP to SART. Silver co-precipitates with copper in SART and is recovered very efficiently with the copper sulphide by-product. Incorporation of SART also allows the leach and CIP circuits to be operated with relatively high levels of free cyanide, which enhances silver leach kinetics and helps keep copper from loading onto the carbon in CIP. The flowsheet was developed in the laboratory and successfully demonstrated in a fully-integrated pilot plant in 2018.

Jan 1, 2019

By J. Budac, J. Dennett, D. Mayne, P. Nawrocki

"The Nickel/Cobalt operation in Fort Saskatchewan, Alberta has successfully used an oxidative ammonia leach process to refine a variety of feeds into high quality nickel and cobalt products for over 60 years. Fundamental changes to the refining process were made when the major feed was converted from nickel concentrate to cobalt rich mixed sulphides in the early 1990s. Since the early 1990s, the production capacity of the refinery has expanded to match increases in both mixed sulphides and other feeds. In addition to increasing the production capacity of the refinery, other changes have been required in order to improve the operability and reliability of the refinery as well as to deal with increasingly stringent safety and environmental requirements. This paper describes recent changes at the refinery including changes to the flow sheet, improvements in unit operations, incorporation of new feeds, management of byproducts, and control of impurities.INTRODUCTION The Cobalt Refinery Company (Corefco) plant in Fort Saskatchewan processes nickel-cobalt mixed sulphide intermediate produced at the lateritic nickel mine and high-pressure acid leach (HPAL) facility in Moa Bay, Cuba. Both operations are jointly owned and operated by Sherritt International and General Niquel of Cuba. The mixed sulphide, along with other feed materials, is processed at the Fort Saskatchewan refinery using a pressure ammonia leach-hydrogen reduction process to produce nickel and cobalt metal. This refinery was originally constructed in 1954 to treat nickel concentrate from Sherritt’s Lynn Lake mine in Manitoba. (Benson and Colvin, 1964; Boldt and Queneau, 1967; Forward, 1953; Forward and Mackiw, 1955; Kerfoot, 1989) From the mid-1970s until the early-1990s, the facility operated as an independent refinery, treating nickel-bearing feeds from around the world. The flowsheet was changed in 1992 to address the increased cobalt content of the feed. (Cordingley and Krentz, 2005; Kerfoot and Cordingley, 1997) The flowsheet was adapted further in 2009 to improve cobalt speciation in the leach process, which allows better cobalt-nickel separation. The 2009 iteration is shown in Figure 1. Three ammonia leach stages were used to ensure high recoveries of nickel and cobalt. Underflow solids from the final leach stage contained mainly iron oxides. One of the features of the leach process is the innovative recycling of ammonia. Ammonia vented from the leach process in tail gas and from atmospheric tanks is recovered and recycled into the refinery using water based scrubbers and a high pressure distillation process. Indeed, roughly 250 t NH3/d is recovered as distillate and recycled back into the process. Also, air enriched with ammonia which is vented from the later first stage autoclaves is recycled to the lead first stage autoclaves to maximize oxygen and ammonia utilization."

Jan 1, 2017