Search Documents

By W. T. Sampson

Introduction The Kirkland Lake (Ontario) property of Wright-Hargreaves Mines, Limited, - consists of four claims. The two main shear zones or 'breaks' of the Kirkland Lake camp extend through three of these claims, for a distance of approximately 3,500 feet. These claims are on the northeast side of the original lake. The water in this section of the lake has now been replaced with mill tailings. The degree of success of any completed undertaking, especially in the mining industry, reflects the personnel involved. I state with pleasure that the successful deepening of No. 5 winze from 6,400 feet to 7,272 feet was largely due to the co-operation and skilled workmanship of Shaft Captain J. Myelde and his efficient 'leaders'. This winze was sunk at a time when it was most difficult to obtain experienced shaftmen, with the result that the crews did not wholly consist of experienced men (although their desire to learn shaft sinking soon gave good results). This condition added greatly to the responsibilities and duties of those in charge, whose first consideration was for the safety of those engaged in the work, and I take great pride in recording that the entire sinking programme was completed without a lost-time accident. Location of Winze Due to the information obtained through deep diamond-drill holes collared below the 6,000-foot level being of sufficient importance to warrant further exploration, it was decided to deepen the existing No. 5 winze rather than sink another winze. This decision meant that the sinking must be co-ordinated with and proceed simultaneously with operations in the winze, where mining was being carried on between the 3,900-foot and 5,100-foot horizons, inclusive.

Jan 1, 1948

By A. E. Flynn

THERE is at the present time a revived interest in amalgamation, due to the number of mines starting up, usually on high-grade ore, and utilizing this relatively cheap and convenient means of recovering gold, more especially in their initial stages of production. The marked increased use of the amalgamation process has revealed a dearth of amalgamators and there is no doubt the art of amalgamation has stood still for a generation or two and is not readily applicable to the modern practice of milling gold ores. Mill operators of long experience are learning the art for the first time and are giving it intelligent study, and considerable testing and research work is now being undertaken Most millmen consider amalgamation a simple process, and so it is when we have a clean ore with coarse gold, specially when stamps are used for crushing. In treating Nova Scotia ores by stamps and amalgamation, recoveries of 95 to 97 per cent are common and easily obtained. So-called 'under-water feed' is almost universally used in Nova Scotia and is quite beneficial. The water is supplied through jets between the dies and below the die surface and maintains this space as a live trap which catches the gold particles before they are overground and spoilt for amalgamation. With this method, the portion of gold recovered in the battery is higher than usual and often amounts to 80 per cent of the total gold in the ore, the remaining 20 per cent being caught on the plate. As a continuous amalgamator, the simple plate cannot be excelled. Some of the modern devices having moving or covered and not very accessible plates, which cannot be readily inspected and dressed to keep them in condition, do not give the best results in service. An exception might be drawn in the case of amalgamation of very heavy ore or concentrate which would bank up unless the plate is carried at such a steep inclination as to weep mercury. Difficulties in stamp-mill amalgamation are encountered when acid water is used or when grease is present. Also, certain sulphides and graphitic and talcose ores give trouble, resulting in poor gold recovery and high mer-cury loss. The older literature on gold milling deals with the common troubles of this type and the old-time amalgamator was well able to take care of day-by-day difficulties. When the difficulties were unsurmountable, the ore was classed as 'refractory' and other processes were used.

Jan 1, 1939

By John C. Wilmot, Robert E. Brewer, Royce J. Smith

In March 2003, Phelps Dodge started up an innovative pressure leach facility for processing copper concentrates at the Bagdad mine in Arizona. This paper describes the development of the concentrate leaching plant at Bagdad and the operational results from start up to present. Optimization efforts and an approach to mineralogical modeling of the concentrate to calculate oxygen utilization are also presented.

Jan 1, 2004

By E. Wraith, W. W. Culver, B. Wesstrom, P. J. Mackey

Electrodeposited copper of the 1860s was of unprecedented purity, although the profound significance of this achievement was not fully realised until the dawn of the electrical age a decade or so later. By the 1870s there were three somewhat large (4 to 4.5 tonnes Cu/day) electrolytic copper refineries in Germany based on J. B. Elkington’s process, first patented in the United Kingdom in 1865. More such refineries were planned throughout Europe. At the same time, copper output in the U.S.A. was starting to expand and with the spread of European electrolytic copper refining technology across the Atlantic, the door opened to major increases in North American output. The technology was first taken up in 1879 by James Douglas at the Chemical Copper Company in Phoenixville, Pennsylvania, where he was Superintendent. Douglas was assisted in this pioneering work by Edward Weston. The copper refinery at the Chemical Copper Company was small, not unlike the first plants in Europe. The present authors contend that the electrolytic copper refinery at the Chemical Copper should be regarded as the first copper refinery in the United States. The Balbach Copper Refinery in New Jersey, which commenced operations in 1883 with an initial production of about 2 tonnes Cu/day, has been erroneously considered as the “first commercial refinery”; it rightly belongs in second place. The early developments at these plants are discussed in this paper. INTRODUCTION In the mid-1800s, the main uses for copper were as sheathing on the wooden sailing ships of the day to protect from marine growth, boiler components in locomotives and steam engines, along with some construction uses. Copper ores were generally smelted, and further fire-refined for market. The recovery of gold and silver, if present in payable amounts, was a slow and relatively expensive step. This situation regarding copper would change by the 1870s with advances in the generation and use of electricity. The introduction of the dynamo led to major developments in electrorefining. First demonstrated in principle by Faraday in 1831 (Faraday, 1832), the dynamo was subsequently adapted and further developed by J.S. Woolrich for electro-metallurgical applications in 1842 (Woolrich, 1842; Napier, 1845). It provided a new source of power with the unprecedented potential to significantly change the scale of metal production by electrometallurgy. Interestingly enough, copper would be needed for the electrical age just beginning. By 1869, advances in dynamo design offered relatively reliable large machines, which enabled J. B. Elkington in the United Kingdom to use the dynamo in the radically new Pembrey copper electrorefinery — the first copper electrorefinery in the world (Wraith, 2013). Initial production at Pembrey was small — in the range of 1 to 2 tonnes/day — while gold and silver were recovered more readily by the treatment of the slimes than with methods used hitherto.

Jan 1, 2019

By Marcel Labbé

La largeur de l?armature peut être modifiée selon les besoins du client entre 48 " et 64" de largeur totale, donc 2 sections de 24" à 32". Ceci permet à l?opérateur d?effectuer le démantèlement de l?équipement pour le déplacement dans les endroits restreints. Le déménagement d?un niveau à un sous-niveau devrait se faire dans un quart de travail de 8 heures. L?option de largeur permet au client de choisir un équipement adapté à son environnement de travail (1). La largeur de la table de forage peut être modifiée selon les besoins du client entre 48" et 96". Cette particularité permet une meilleure stabilité, et plus de précision dans le forage (2). Il y a 4 pattes hydrauliques à chaque coin pour la stabilisation lors de forage (3). La table de forage a 360° d?angle de forage sur 3 côtés du transporteur. La table peut sortir de chaque côté du transporteur de 40 ½" à partir du centre du transporteur pour faciliter la mise en place de la foreuse dans les endroits difficiles d?accès. La plage de forage est considérablement agrandie. Cette caractéristique qui fonctionne hydraulique, permet à l?opérateur de forer sans être obligé de changer la position du transporteur pour des changements de trous. Tous les types de foreuse peuvent être installés sur cette table de forage (4). Sa petite dimension lui permet d?accéder, par des monteries de 30" de diamètre, à des sites de travail de 2,5 mètres de hauteur et largeur. C?est un équipement adapté aux gisements filoniens. Ce genre de gisement est de moins en moins rentable pour les compagnies minières. La mécanisation des ces gisements va permettre de les rentabilisés en augmentant la productivité et la santé du travailleur, en réduisant la dilution (5). Les manettes de contrôle de la foreuse, les mouvements de la table de forage ainsi que le déplacement du transporteur ont été installés selon les recommandations d?un ergonome. Des recherches ont été effectuées par ce spécialiste sur les cas d?accident survenus avec l?utilisation de ce genre d?équipement. Il a déterminé les positions le plus confortable que l?opérateur doit prendre pour éviter les douleurs prolongées (6). Le système de roulement est composé de 4 roues pleines installées sur 4 planétaires de 9000 à 15000 livres de capacité munis chacun d?un moteur hydraulique. Des freins ont été installés sur les planétaires pour assurer la sécurité de l?opérateur et faciliter le positionnement du transporteur lors du forage. Des roues rétractables peuvent être installées pour faciliter l?accès sur rail (7). Ce transporteur peut être alimenté par une puissance électrique plutôt que par une puissance pneumatique. Cette puissance électrique est fournie par un Power Pack qui transforme l?énergie en puissance hydraulique. Ce type d?alimentation est employé lors du forage de développement, mais il peut aussi être utilisé pour le forage long trou. Cet avantage permet au client qui a un problème de pression d?air d?utiliser l?électricité. Par contre si vous utilisez l?électricité mais que dans un secteur isolé le gros courant électrique n?est pas accessible vous pouvez utiliser votre équipement en utilisant la puissance pneumatique. Le changement d?alimentation énergétique se fait facilement (8). Cet équipement est construit pour effectuer 4 types d?activités : forage de développement de niveau et sousniveau avec l?installation d?un bras porteur, forage et pose de câbles d?encrage pour soutènement de terrain, forage de production long trou et forage de monterie ascendante et descendante. L?avantage est que vous investissez dans un seul équipement au lieu de 2 ou 3. Cet avantage vous fait économiser dans votre budget d?équipement. En plus cet équipement est construit pour de dure travaux et ne contient aucun système électronique (9).

May 1, 2001

By Alfred W. G. Wilson

In this paper is presented a review of the changes that have taken place in certain Canadian non-metallic mineral industries since 1909. The fifteen-year period 1909 to 1923, inclusive, has been selected for two reasons. In the first place, statistical treatment of the subject under review has been nearly uniform throughout the period. In the second place, this decade and a half is itself further subdivisible into three well marked quinquennial periods, the middle one covering the period of the great war when industrial conditions were greatly disturbed. It then becomes possible to institute certain comparisons between equal periods before and after the war disturbances. The items selected for inclusion in this review are certain of the more important members of that class of minerals usually grouped together under the heading of non-metallics. They are all minerals of which Canada is known to possess important resources, and which are indispensable to many of our greatest manufacturing industries.

Jan 1, 1925

By J. F. McMahon

Introduction The greater portion of the information presented in this paper was obtained in the course of an investigation on clay gathering and its cost in the provinces of Quebec and Ontario (1). For assistance in the preparation of the paper, the writer wishes to record his thanks to Mr. Howells Fréchette, Chief of the Ceramics and Road Materials Division of the Mines Branch. Clays are mineral substances consisting essentially of hydrous aluminium silicate which become plastic when wet, fairly hard when dry, and stony masses when burned to a sufficiently high temperature and re-cooled. Shales are clays which have been indurated by the processes of nature. Millions of tons of clays and shales are won yearly for the production of brick, tile, sewer pipe, drain tile, roofing tile, fire-brick, china-ware, wall and floor tile, cement, and a host of other products. There are certain types of clay which, due to their particular qualities and limited distribution, are mined entirely or in part for sale to manufacturers, and are even exported from one country to another, as for example china-clays or kaolins, utilized in the manufacture of white-wares and in the paper industry, due to their consistent whiteness; ball-clays, utilized in the white-ware industry, due to their bonding power and whiteness; slip-clays, used in the stone-ware industry because of their glazing properties, and in the grinding-wheel industry for their burned bonding properties; and suspension-clays, such as are used in the enamelling industry. However, the great bulk of clays and shales won are used in the production of heavy clay products, and the manufacturer of these generally owns and operates his own deposit of raw material.

Jan 1, 1933

By P. R. Warner

This paper reviews the development of certain aspects of the electrical specifications of Anglo American?s suite of specifications for gearless mill drives (?GMDs?). These specifications are based on experiences in both Anglo American?s and others? operations, benchmarking against large hydro generators, the advice of industry and university experts, and continuous close co-operation with OEMs. To achieve a step change in availability additional final testing and electrical protection have been implemented, insulation requirements have been specified for machines to be operated at high altitude and clean area and access control systems have been developed.

Jan 1, 2012

By Stephen Hardcastle

Supplying ventilation in underground metal mines can be one of the most energy demanding services required to support production activities. Consequently, as energy, in the form of electricity or combustible fuels can be expensive and their unit cost is expected to increase, there is significant interest in reducing the overall demands of a mine?s ventilation system through such initiatives as controlling ventilation based upon demand and exploring other power alternatives to the current usage of the diesel engine in mobile mine vehicles. However, determining the benefit of any energy saving technology is complex and not universal applicable across the industry, consequently they have not been widely adopted. For these technologies to succeed they must be strategically applied based upon sound business cases. The intent of this paper is to provide information on some of the prospective control strategies and their potential impact on the power consumption related to supplying ventilation.

May 1, 2007

By H. T. Kennedy, D. L. Flock

"The project described in this pa-per was undertaken to provide a more thorough understanding of the effect of contamination by drilling fluids on the electrical properties of porous systems. The basic work per-formed was filtration tests on both consolidated and unconsolidated sands and the determination of their resistivity profiles with the aid of screen-type electrodes spaced at convenient intervals along the core.Four drilling fluids were selected, ranging in resistivity from 447.0 ohm-cm. to •5.76 ohm-cm. The permeability of three unconsolidated and four consolidated cores, on which resistivity measurements were made, varied from 1,257 md. to 4,560 md. Five additional cores with permeabilities as low as 49 md. were tested to investigate the effect of permeability on the depth of invasion of drilling fluids.The effect of drilling fluid invasion on resistivity profiles was determined on cores containing brine only, and on those containing 80 to 90 per cent oil and 20 to 10 per cent brine. The study included measurements of (a) clay content of different sections of the core, (b) saturation of the invaded fluids and oil in different parts of the core, and ( c) changes in resistivity as a result of gravitational re-distribution of fluids and diffusion of electrolytes.The data showed that the resistivity of an invaded core is, as was expected, controlled by the resistivity of the filtrate, the resistivity of residual core water, the resistivity of the clay particles, and the amount and distribution of the filtrate, clays, residual oil, and brine. In most cases there was a significant increase in resistivity owing to the presence of clay solids which had invaded the core. The change in resistivity, as a result of the diffusion of salts, was substantial after a period of five hours. There is evidence in some cases that the residual oil and core water saturations of the unconsolidated cores, after substantial invasion, are very low, indicating almost complete displacement by invading fluid."

Jan 1, 1959

By W. B. Morrey

This paper deals with the development of the new cap-sensitive slurry explosives. The history and special features of these explosives are outlined, and recent field trials are described.

Jan 1, 1973

By A. Rahimi

Refractory castables based on alumina-silicate aggregates are commonly used in casting wheel components and launders. In this research the recycling process of waste magnesia chrome bricks for production of refractory castable lining for launders and casting wheel ladles at Iranian Sarcheshmeh copper complex (I.S.C.C.) is discussed. The smelting plant of ISCC consumes 4,000 tons refractory materials and produces 2,000 tons waste refractories annually. In order to reduce the environmental pollutions and gain the economical advantages, the recycling of waste refractories proved to be a solution [1]. In ISCC, 800 tons alumina or alumina-silicate refractory castables are used for linings of anode furnace ladles and launders annually [2]. In the present work, the spent bricks from reverberatory, converter and anode furnaces were analyzed in term of microstructural changes from hot zone to the cold end to evaluate the changes in texture and chemical composition. Different formulations based on recycled magnesia chrome aggregates and various particle size distribution and cement content were tested. Economic recycled magnesia chrome refractory mixture was prepared after crushing and sizing the non-deteriorated regions of wasted bricks. After evaluation of physical and mechanical properties of samples, one ton of refractory castable was prepared and successfully installed in the casting wheel ladles.

Jan 1, 2007

By J. G. A. Stevenson

GENERAL Location of Property THE Stirling zinc-lead-copper deposit is in Richmond county, Cape Breton, about a quarter of a mile southwest from Stirling P.O., and some 45 miles southwest from Sydney. The property is accessible by road for at least nine months of the year, and during the navigation period coastal boats maintain a service touching at the port of Fourchu, eleven miles from the mine. When flying conditions permit, the Cape Breton Flying Club, of Sydney, will carry passengers to or from the property, a service which has been particularly advantageous on two occasions when hospitalization was urgently required. The Company has mining rights on leases Nos. 73-74, 78-80, and 101-104, inclusive, and owns 166 acres at Stirling and one acre at Fourchu. The ore deposit is in lease No. 73. History The Stirling deposit was discovered in the 'nineties', probably about 1895. The original discovery is said to have been made in the bed of Copper creek, which traverses the ore-zone. For a number of years, indifferent development work was carried on with a view to copper production only, and it was not until1915-16 that attention was directed to the possible production of zinc. Previously, the ore had been considered too complex for metallurgical treatment. During the period 1916-24 several operators attempted to develop the property, among them being the Stirling Exploration Company, Stirling Mining & Smelting Company, New Jersey Zinc Company of New York, Hayden & Stone Company of Boston, and The Eastern Mining & Milling Company. Up to 1924, the work was limited mainly to trenching, stripping, ? diamond drilling, and shot drilling.

Jan 1, 1937

By A. Luszczkiewicz

This paper presents the beneficial effects of non-oxidative leaching of final and intermediate copper sulfide concentrates with sulfuric acid prior to the final cleaning stage of flotation. This unique process, combining leaching and flotation, appears to be advantageous for difficult-to-treat carbonate-bearing Polish copper ores, such as those processed in copper concentrators at KGHM Polish Copper. It was shown that after the chemical decomposition of about 70 % of the total carbonates naturally present in the flotation feed, a considerable enhancement of subsequent flotation results (both grade and recovery). The resulting products of non-oxidative leaching are solid hydrated calcium sulfate (gypsum), soluble magnesium sulfate and gaseous carbon dioxide. The beneficial effect established by the laboratory leaching tests was subsequently confirmed during a pilot plant operation treating final copper concentrate and a problematic intermediate concentrate at the Lubin concentrator.

Jan 1, 2007

By K. E. Waters, E. R. L. Espiritu, G. R. da Silva

"Rare earth (RE) elements are essential components of emerging green technologies. The increase in demand for these applications have driven the search and development of new rare earth deposits such as the Niobec project in Quebec, Canada. This deposit consists primarily of dolomite with significant amount of RE minerals bastnäsite and monazite, the primary sources of RE elements. Due to the minerals’ fine liberation sizes, flotation is commonly used as a concentration method. To develop an efficient process, the electrokinetic properties of the minerals must be understood. In this study, the surface properties of bastnäsite, monazite (RE minerals) and dolomite (a common gangue mineral) were investigated by zeta potential measurements. These measurements are affected by various ions present in solution; for bastnäsite, monazite and dolomite, some of these ions are H+, OH-, PO43- and CO32-. Dolomite, being a sparingly soluble mineral and a primary component of the ore, may be the greatest contributor of these ions in solution in the form of CO32- ions. Thus, different sources of CO32- ions (from dolomite dissolution and from Na2CO3) were investigated. The research work aims at elucidating how these reagents may influence the minerals’ surfaces. The results have shown that dolomite supernatant and sodium carbonate greatly affect the electrokinetic properties of each minerals. The addition of dolomite supernatant have resulted to relatively similar zeta potential of the minerals; while, sodium carbonate have affected them differently. These observations could be useful in efficient flotation of bastnäsite and/or monazite from bastnäsite-monazite-dolomite system.INTRODUCTIONThe increase in the demand for rare earth (RE) elements has driven the search and development of new deposits. Out of 53 rare earth projects in the world, 19 can be found in Canada (Hatch, 2015). These include the Niobec project of Magris Resources Company in Quebec. This deposit contains a significant amount of rare earth minerals (such as bastnäsite and monazite), with carbonates (such as dolomite) as the primary gangue minerals."

Jan 1, 2016

By J. E. Dutrizac

"The end of an era in zinc metallurgy took place on July 31, 1976 when the horizontal retort furnaces of the National Zinc Company in Bartlesville, Oklahoma were permanently shut down (1) . For more than a century, horizontal retorting had been the most common method of producing zinc in the United States; it was a thriving industry in many parts of that country, especially in the natural gas belts of Oklahoma and Texas. With the Bartlesville closure, yet another metallurgical process has become an object of historical interest for North American metallurgists. Although shrouded in controversy, the origins of zinc metallurgy seem to date back at least 2000 years. Pyrometallurgical methods with carbon reductants are capable of producing zinc from oxidic zinc ores, but only above the boiling point of the metal. Although slow cooling results in re-oxidation of the zinc vapour by air or carbon monoxide, quenching yields liquid zinc; some form of rapid cooling, either accidental or intentional, was likely used by ancient metallurgists to liquify the metal. Zinc metal found in Athenian objects of the Roman era was likely of accidental origin. The Romans employed brass extensively for coins and ornaments(2) , and this was intentionally produced by the calamine process whereby oxidic zinc ores were added to molten copper under strongly reducing conditions. Zinc appears to have been known in China and India as early as 1000-1300 A.D., and was probably smelted commercially in those countries from the 14th century. Although the early metallurgical procedures were probably inefficient, they were able to produce zinc metal in significant amounts. The large heaps of zinc residues with clay retorts bear testimony to an early smelting industry of impressive magnitude. It is estimated that the heaps at Zawar, India alone represent the extraction of 100 000 tons of metallic zinc(2) In the 1730s the smelting of oxidic zinc ores was developed in England using a vertical retort method. In 1788 a British patent was granted for making zinc from zinc blends (ZnS) by roasting the ore in a coalfired reverberatory furnace, mixing the calcine with charcoal and smelting the mixture with suitable zinc condensation. The English process was very energy intensive, however, and early in the 19th century the Belgians developed a horizontal retort process for the reductiondistillation of zinc that was more fuel efficient. This technique was gradually developed into what came to be known as the Belgian process, the forerunner of the ""modern"" horizontal retort furnace."

Jan 1, 1999

By Ginger Gibson

As an occupational culture, mining comes with its own set of rules, agendas and values. Yet mines often also operate in the traditional territories of indigenous communities, with whom specific agreements are negotiated that commit to respect culture, economy and environment. Mines in these locations employ extremely diverse workforces whose value systems often come into conflict in on-the-job relationships. Adaptation of individual worker attitudes and industrial operating culture thus both need to occur if there is to be the negotiation of a workable relationship. This paper will discuss ways that NWT diamond mines have adapted to their workforce, to ensure that rights and cultures of their diverse workforce can be respected. Historically, the concept of culture has been dealt with solely through the forum of ?cross-cultural? workshops. Gibson presents a model of a new type of ?cultural-engagement? workshop based on the top ten cross-cultural conflicts that actually arise at a remote mine-site. This model helps managers, team leaders, and workers to tackle in-mine conflicts that arise based on differing value systems of aboriginal and non-aboriginal workers and management. In addition, Gibson suggests that the concept of culture must be more rigorously applied throughout the mine structure and not discussed only in the forum of the cross-cultural workshop.

May 1, 2007

By Lawrence Bragg

WE associate metals with hardness, toughness, and strength. But a curious paradox lies at the root of the valuable mechanical proper-ties of the metallic state: in order to be strong, a metal must be weak. This paradox, and the equally surprising fact that, in a sense, metals are not true solids at all, are among the topics here discussed by Sir Lawrence Bragg. (1) WHAT METALS MEAN TO US We employ various materials to build or fabricate the many objects we use in everyday life, choosing those whose properties are most suitable for the purpose which the object has to serve. Certain of these materials have been used from the earliest times, such as stone, wood, leather, and animal or vegetable fibres, each with its own peculiar valuable properties. Stone resists crushing and is very durable and permanent, as indeed it must be, since it has so long resisted change as a part of-the earth's crust. It is there-fore ideal for walls and buildings, and very early in his history man discovered how to make artificial stones by burning clay, with the advantage that they could be given any desired shape, and made into bricks or given elaborate forms as pottery. Wood is strong and tough and light, it resists tension as well as compression, and is nor brittle like stone. It forms beams and furniture and parts of tools or weapons. Leather is tough but at the same time iris flexible; it is ideal as straps or sheers. Vegetable fibres such as linen or cotton, and animal fibres such as wool and silk, owe their value to their flexibility and strength in resisting extension. They can be spun into yarn or rope, and woven into cloth. The technological age in which we are now living is replacing the natural products used by early man by a series of artificial products, but it is remarkable to see how in nearly every case we are copying Nature's materials. The wide use of concrete represents a developed art of making artificial stone. Artificial fibres such as rayon or ?nylon replace cotton, wool, and flax. Plastics are coming very much to the fore; they correspond to early man's use of horn, another substance with peculiar properties of roughness in all directions without the 'grain' of wood. For the most part we are following in the footsteps of our remote ancestors, though we can make for ourselves what they had to cull from wood and field. There are exceptions; for instance, we have discovered comparatively recently the number of uses to which natural rubber can be put, and are now making it artificially. This is a really new discovery; our ancestors had nothing with such remarkable powers of elastic stretching without breaking, and resistance to being abraded.

Jan 1, 1943

By J. W. Baker

"The Kerr-Addison mine is on the northeast shore of Larder Lake in the township of McGarry, District of Timiskaming, Ontario. It lies just south of the highway leading to the town of Kirkland Lake, 25 miles to the west.The property was first staked in the summer of 1906, by a party of prospectors led by a Dr. Reddick of Ottawa. Subsequent assessment work resulted in the erection of a 20-stamp mill in 1908. Gold from this mill was used in the first gold coins to be minted in Canada. The operation did not prove successful, however, and mining was suspended. In 1914 a consider-able amount of underground development was undertaken by the Associated Goldfields Co., without success.In 1936 Kerr-Addison Gold Mines Co. carried out large-scale sampling from four adits driven into the hillside at the mine. Results were not satisfactory, but it was decided to drill one last deep diamond drill hole from surface. The hole cut a wide section of gold ore. With this encouragement, further development outlined a large tonnage of ore, and a 500-ton mill was put into production in May, 1938. In 1939, its first full year, the mine produced 54,480 ounces of gold and 2,732 ounces of silver. By 1955 the mill had been expanded to a rate of 4,549 tons daily, and in this year 427,193 ounces of gold and 23,490 ounces of silver were produced.From 1938 to the end of 1955 the total production, from 17,473,797 tons milled, has been 3,607,462.74 ounces of gold (0.2064 ounces per ton), and 182,278.56 ounces of silver, with a total value of $131,073,037."

Jan 1, 1949

By H. A. Khorami, T. Wong, B. Velapatino, E. Asselin, T. Donnelly, E. Bryce, R. Dixon

A copper–nickel concentration gradient alloy was designed and fabricated through a powder metallurgy (PM) process. Copper and nickel powders were mixed with different weight ratios from 0 to 100% copper in 10% increments. Each powder mixture was poured inside a cylindrical die and compacted between two punches using a hydraulic press machine at pressures up to 70 MPa, resulting in approximately 1 mm thick layers (discs) of pressed Cu–Ni powder. These 11 Cu–Ni compacted powder layers, i.e. 0–100% Cu with 10% increments, were then compressed together with pressures up to 420 MPa to form a green part. The green part was sintered in a vacuum furnace at 1000°C for 10 hours to form a solid mass (PM part) of Cu–Ni concentration gradient alloy. In the sintering process, Cu and Ni particles fused together and formed a single piece due to diffusion of the atoms across the boundaries of the particles. The diffusion of atoms also converted the stepwise concentration change into a uniform concentration gradient. INTRODUCTION Copper has numerous applications in different industrial sectors due to its superior physical, electrical, mechanical and chemical properties such as its excellent thermal and electrical conductivity, resistance to fatigue, high ductility, and resistance to corrosion. Moreover, copper and its alloys have natural antimicrobial properties. This has opened up new applications for copper–based self–disinfecting surfaces in healthcare in an effort to mitigate healthcare–associated infections (HAIs). HAIs affect millions of patients each year, leading to significant morbidity and mortality as well as financial losses to healthcare systems (World Health Organization, 2016). HAIs spread through three main routes: (a) iatrogenic in which HAIs are a direct consequence of medical encounters and/or treatment; (b) person to person where organisms are transferred between healthcare workers, patients, and visitors; and (c) environmental where transmission occurs via contaminated surfaces and equipment (e.g. doorknobs, railings, toilets/commodes, medical carts). The use of antimicrobial copper–based materials on high touch surfaces could diminish pathogen transmission via this latter rout. This has subsequently led to the development of a variety of copper–based materials for use in healthcare settings and promoted the investigation of the antimicrobial efficacy of copper–based materials.

Jan 1, 2019